Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 24-01-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 29-01-2025 |
| 2 | 17-01-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 24-01-2025 |
| 3 | 07-01-2025 | BOQ Corrigendum | BOQ | 17-01-2025 |
| 4 | 31-12-2024 | Corrigendum to date | Date | 17-01-2025 |
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness below or above the ground level and removal of debris from site, complete all as specified and directed.Note:- Demolition includes PCC/ floor finishes such as kota stone/ floors tiles of any description. No extra cost to be born by the Govt exchequer for any of the above. |
| 2 | Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles,complete all as specified and directed. |
| 3 | Taking down cement plaster on brick walls or concrete surface etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.Note :- The cost includes any thickness found during execution increased due overleaping of n number of layers of plaster, tiles, mosaic finish without any cost to govt exchequer |
| 4 | Taking down door shutter of any description exceeding 1.0 Sqm but not exceeding 2.0 sqm and refixing in the same opening, complete all as specified and directed. |
| 5 | Taking down door shutter of any description exceeding 1.0 but not exceeding 2.0 sqm, complete all as specified and directed. |
| 6 | Taking down chowkhats or frames(without taking off shutter from the frames) exc 1.5 Sqm and n exc 4 sqm, complete all as specified and directed.Note:- The rate includesmaking good of surfaces without any extra cost to Govt |
| 7 | Taking down chowkhats or frames(without taking off shutter from the frames) n. exc 1.5 Sqm, complete all as specified and directed.Note:- The rate includesmaking good of surfaces without any extra cost to Govt |
| 8 | Dismantling of cast iron or PVC pipe upto 100mm bore, jointed in cement mortar in any position, complete all as specified and directed by Engineer -in - Charge. |
| 9 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. |
| 10 | Dismantling structural steel work as in framed trusses n exc 10.00 mtr, complete all as specified and directed. |
| 11 | Dismantling structural steel work of any description not otherwise provided, complete all as specified and directed. |
| 12 | Dismantling of asbestos cement (corrugated, semi corrugated etc)/ PVC sheets in roof covering including ridges, complete all as specified and directed. |
| 13 | Dismantling of timber scantling 40 Sqcm and over in section, in any position as in unframed or framed work, complete all as specified and directed. |
| 14 | Hacking out old broken glass (any thickness size, quality or description from wooden or steel frames glazed with putty / beads, complete all as specified and directed. |
| 15 | M&L for walling of random rubble, uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed. |
| 16 | Description all as per srl item no. 15 here-in-before but except stone, complete all as specified and directed. |
| 17 | M&L for precast plain cement concrete, 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in bond stones set in cement mortar 1:6 complete all as specified and directed. |
| 18 | Extra over stone walling for hammer dressing to face stone and dressing of face beds with maximum depression on face from straight edge held against the dressed surface on sand stone n.exc 20mm, complete all as specified and directed. |
| 19 | M&L for brick work with sub class \"B\" bricks, old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:4 , complete all as specified and directed. |
| 20 | Description all as per srl item no. 19 here-in-before but except bricks. |
| 21 | M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:6 complete all as specified and directed. |
| 22 | M&L for applying water proofing or damp proofing treatment to wall surface with smart care damp block or other equivalent from Fosroc/ Asian paint/ Sika/ Pedilite by elastomeric cementious coating including all necessary surface preparation,etc complete all as per manufactureres specification and application methodology, the coating shall be applied in two coats achieving proper finish, complete all as specified & directed. |
| 23 | M&L for rendering 15 mm thickon concrete surface /brick surface on wallin cement mortar 1:4, finished even and smooth without using extra cement, complete all as specified and directed. |
| 24 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar (1:6), finished surface even and smooth without using extra cement complete all as specified and directed. |
| 25 | M&L for rendering 05 mm thick in cement mortar 1:3 on concrete surface of ceiling, finished surface even and smooth without using extra cement, complete all as specifed and directed. |
| 26 | M&L for rendering 20 mm thick on fair faces of stone walls in cement mortar (1:4), finished even and smooth without using extra cement complete all as specified and directed. |
| 27 | M&L for providing 75mm cement concrete, type C-1, 1:3:6, (using 20mm graded crushed stone aggregate)as in plinth protection, laid in slope 1:12 from outer edge of the wall,finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight), complete all as specified and directed. |
| 28 | M&L for plain cement concrete 1:2:4, type B-1, (using 20 mm graded crushed stone aggregates)as in coping to path, edging, benching and the like including form work, complete all as specified and directed. |
| 29 | M&L for plain cement concrete 1:3:6, type C-1, (using 20 mm graded crushed stone aggregates)as in surface channel and drains, complete all as specified and directed. |
| 30 | M & L for 25 mm thick plain cement concrete 1:2:4,type B-0 (using 12.5 mm graded stone aggregate) as in sub base, finished fair for receiving floor finish, completeall as specified and directed. |
| 31 | M & L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, completeall as specified and directed. |
| 32 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar (1:4), finished surface even and fair for receiving tiles as in dado/skirting, complete all as specified and directed. |
| 33 | M&L for 18-20mm thick machine cut kota stone slab(mirror polished) (area of each slab n. exc 0.27 Sqm except space constraint) as in flooring, laid and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including 15mm thick screed bed in cement mortar 1:6, after dismantling old unserviceable kota stone, complete all as specified and directed. |
| 34 | Cutting to existing kota stone flooring includig minor repairs and polishing, complete all as specified and directed. |
| 35 | M&L for 19mm thick granite stone slab (of any type) work (table rubbed and polished) in cooking platforms, in steps, pillars, window cills, jambs etc, laid over 15mm thick bedding in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite slab, rounding edges etc after dismantling of old unserviceable granite stone slab of any size, complete all as specified and directed. |
| 36 | M&L for Green marble work of any type 16-20mm thick (table rubbed and polished) as in flooring, top of slabs, steps, jambs, pillars, window - cills, and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of marble including grinding and polishing after dismantling of existing marble slab, complete all as specified and directed. |
| 37 | Providing edge moulding to any thickness ofMarble/Granite stone of any descriptioins including machine polishing to edge to give high gloss finish etc., complete all as specified and directed. |
| 38 | M&L for vitrified tiles (light shade) of size600x 600x 08 to 10mm thick (premium quality) as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified and as directed.Note:- The contractor shall have no claim on difference what so ever on shade /colour of tile. |
| 39 | All as per item ser No 38 but in vertical surfaces, complete all as specified and as directed. |
| 40 | M&L for Vitrified Ceramic tiles 8-10 mm thick (square/ rectangular) of approved colour polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry. The tiles shall be fixed by using spacers and filling the epoxy to match the tile surface,complete all as specified and directed. |
| 41 | All as per item ser No 40 but in vertical surfaces, complete all as specified and as directed. |
| 42 | M&L for non skid ceramic coloured tiles 7 mm thick (premium quality) (as approved by Engr-in-Charge) Square/rectangular, area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified and as directed. |
| 43 | M&L for glazedceramic coloured tiles of size 350x250 x7mm/ 450x350x7mm thick,(premium quality)on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified and as directed. |
| 44 | M&L for wooden laminate floor tiles 7 mm thick with dove tailed joints laid over 150 micron polythene film and 3 mm thick foam as per manufacturer\"s instructions and fixed complete as in floor and skirting (as approved by Engr-in-Charge), Complete all as specified and as directed. |
| 45 | S&F in repair Stainless steel curtain rod 25mm dia with fixing brackets, dooms and knobs at both ends as per requirement, complete all as specified and directed. |
| 46 | S&F wooden finish single bracket holders for curtain rods (matching with curtain rods) with end stops, complete all as specified and directed. |
| 47 | S&Fin repair steel rolling shutter 1.25 mm thick with ball bearing, as specified including top cover, anchoring rod, hasp and stapple, guiding rail and one shop coat of primer, erected in position as indicated complete push pull or manual type including formice mortice holes for fixing of shutter with PCC 1:3:6, type C-0 using 12.5mm graded stone aggregates, complete all as specifed and directed. |
| 48 | S&F forpressed steel door frames of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including a shop coat of zinc chrome primer including back filling with PCC 1:3:6, type C-1, using 20mm graded stone aggregates, complete all as specified and directed. |
| 49 | S&F for pressed steel door frames of size 105x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including a shop coat of zinc chrome primerincluding back filling with PCC 1:3:6, type C-1, using 20mm graded stone aggregates, complete all as specified and directed. |
| 50 | S&F for factory made 35 mm thick 2nd class hard wood plain frame pannelled shutters (two panels and double shutter) with lock rail and pannel or 9mm BWP comerical ply or 12mm venered particle board with comerical face verering on both faces. The sizes of rail and style as per IS-1003 part kiling seasoned, complete all as specified and directed. |
| 51 | S&F for factory made 35 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specifiedin SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and directed. |
| 52 | S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square, complete all as specified and shown on drwaing in SSR Part-II (2020). |
| 53 | S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & shown in drawing mentioned in SSR Part-II 2020, complete all as specified and directed. |
| 54 | S&F for 100mm long butt hinges medium weight cold rolled mild steel (ISI Marked) , complete all as specified and directed. |
| 55 | M&L for300mm brass ordinary rat tail rod pattern door springs (ISI marked) of approved make including roller and roller plate, complete all as specified and directed. |
| 56 | S&F for factory made MS tubular Box type window (double rebate and double shutter) of MS rolled steelsection conforming to IS-1038 and shall be ISI marked manufactured by ISI approved manufacturer, openable frames shall be fabricated of sections as approved by Engr-in-Charge, corner welded to form a solid fused welded joint, handles shall be of Z section welded with openable frame box steel section used in outer frame, shutter frame and central frame shall be ERW secton of 16 gauge with fixing lugs to be fixed as per provision of IS-1038except that top lugs shall not be provided , all shutters of windows shall be provided with 4 Nosfriction free hinges, 2 Nos 75 mm tower bolts to each leaf of window one at top and one at bottom welded on 3 mm thick steel sheet piece of suitable size which shall be in turn welded to Z section of steel window to provide suitable arrangement of using tower bolt. Glazed, gauzedwindow , mild steel casement stays 300 mm with hinged joint and two plates with studs complete all as specifiedwith all fittings and fixtures without glazing bars including 3mm thick sheet glass ordinary quality and GI wire mesh of 0.56mm nominal dia and average width of aperture 1.18 mm etc, complete all as specified and directed. |
| 57 | S & F of 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and directed. |
| 58 | S& F for galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18m and fixed with tinned tacks, or galvinsed wire staples including cutting, welding etc for steel window / ventilators, complete all as specified and directed. |
| 59 | M & L for powder coated (customised design heavy duty) aluminium frame of any colour (thickness or powder coating not less than 50 micron)for doors, windows frames, other sections for doors, windows, ventilators with one or more rebates channel for sliding shutters, grilll etc including joining cleats for fixing etc, complete all as specified and directed. |
| 60 | S&FPowder coated aluminum American handle cast type 200mm longfor doors (ISI marked), complete all as specified and directed. |
| 61 | S&F powder coated aluminumhandle cast type 100mm collapsible type (ISI marked), complete all as sepcified and directed. |
| 62 | S & F of powder coated 75 mm long butt hinges, extruded aluminum alloy (ISI marked), complete all as specified and directed. |
| 63 | S&F for rubber gasket of size for fixing aluminum door/ window/ ventilator shutters, completeall as specified and directed. |
| 64 | M & L for anodised aluminium (customised design heavy duty) for doors, windows frames, other sections for doors, windows, ventilators with one or more rebates channel for sliding shutters, grilll etc including joining cleats for fixing etc, complete all as specified and directed. |
| 65 | S&Faluminum American handle cast type 200mm longfor doors (ISI marked), complete all as specified and directed. |
| 66 | S&F Anodised aluminumhandle cast type 100mm collapsible type(ISI marked), complete all as sepcified and directed. |
| 67 | S & F of anodised aluminum 75 mm long butt hinges, medium weight cold rolled extruded aluminum alloy (ISI marked), complete all as specified and directed. |
| 68 | S&F door closer hydraulically regulated, aluminium (extruded section body) designation No 2, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg (ISI Marked), Complete all as specified and directed. |
| 69 | S&F fordouble action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed (ISI Marked),completeall as specified and directed. |
| 70 | S&F aluminum alloy wire cloth , 0.45 mm nominal dia of wire and avg width of aperture 1.40mm and fixed withaluminum stapples , complete all as sepcified and directed. |
| 71 | S & F for brass morticelock vertical type 100 mm long with 4 levers(ISI marked), complete all as specified and directed. |
| 72 | S&F for sheet glass 5.5 mm thick, ordinary quality and fixed with aluminum & rubber beading in square exc 0.5 sqm in each pane, complete all as specified and directed. |
| 73 | M&L for taking down old aluminium shutters and refixing in the same opening after necessary repairing including replacement of all necessary fittings, complete all as sepcified and directed. |
| 74 | complete remova of existing water proofing treatment on non approachable / non accessible roof surface horizontal and vertical surfaces in following sequence through manufacturer / authorized applicator of the manufacturer complete all as specified and directedby Engr-in-Charge:-(i) Taking down/removing existing treatment and cleaning properly with wire brushing etc,rabish off from the premishes (ii) 10mm thick plastering on roof surfaces in cement mortar 1:4 mixed with water proofing compound as per manufacturers instructions(iii) after drying concrete surfaces and apply a coat of bituminous primer @0.40 Kg/Sqm on the prepared surface of roof (iv)After the primed surface has dried, apply a coat of hoat blown bitumen85/25 or equivalent viscosity grade @ 1.2 Kg /Sqm of the surfaces etc complete.(v) Laying unrolled over the bitumen coated surfaces polymeric water proofing membrane, of approved make standard weight not less than 3 Kg / sqm with 100 mm over laps shall be sealed by flame as per manufacturer instruction.(vi) Applying a coat of hot air blown grade bitumen of grade 85 / 25 @ 0.5 Kg / sqm duly sanded over polymeric membrane complete. Note :- Rate of WPC will be included in the quoted rate. |
| 75 | S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS-1161(1979) grade ST-240 complete all as specified and directed. |
| 76 | Erection and fixing steel work in roof trusses including special shape washers et. Complete using using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240. complete all as specified and directed by Engineer-In-Charge. Note:- Old steel retrieve from dismantling shall be re-use. |
| 77 | S&F in repair for roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy brackets framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats, etc. conforming toGde Fe-290E-165, complete all as specified and directed. |
| 78 | S&F Mild steel bolts.exc. 5 cm lengthnot exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed by engineer-in-charge. |
| 79 | S&F (plain orchequered ) channels ,square cutor notched ( oridinary and counter sunk) forming holes , w/o any attatchment, complete all as specified and directed. |
| 80 | M&L for preformed material for plugging the holes in AC / CGI sheets as required, complete all as specified and directed. |
| 81 | S&F self adhesive membrane over leaked GI sheet 1.5mm thick self adhesive elastomeric SBS (Styrene Butadiene Styrene) bitumen based membrane with high density aluminum film on top, provided with Pibial / Emufal TE Bitumen primmer @0.3 ltr per sqm , mimimum over laps shall be 50mm on sides and 100 mm on end laps, complete all as specified and directed. |
| 82 | Heavy Duty reinforced acrylic coating for terrace/walls water proofing over a coat of Primmer for Sealer coatwith roller, complete all as specified and directed. Make:-Dr Fixit/ Sika/ Asian paint |
| 83 | M&L for framing for partition/ cladding by using stainless steel of different size sections and shapes as per ground requirement of reqd shape (Curve or Plain ) (Gde 304 ISI marked) for fixing of boarding using clamps nut boltsusing seamless welding buffing in such a way that no joint is visible, complete all as specified and directed. |
| 84 | S&F in repair 8 mm thick double wall standard polycarbonate sheets of approved colour fixed to MS frame using screw / bolts/aluminum profile and rubber packing including sealing of joints by using silicon gel, complete all as specified and directed. |
| 85 | S&F for Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mmthick of approved colour having tensile strength 550 MPa as in roof covering / cladding to wall of any radius as directed by GE fixed with self tapping screws including side end lap as per manufacturer\"s instructions including dismantling, complete all as specified and directed. |
| 86 | S&F for Pre-painted galvalume aluminium zinc coated GI based plain steel sheet 0.50mmthick of approved colour having tensile strength 550 MPa as in roof bent to a curve of any radius as directed by GE fixed with self tapping screws including side end lap as per manufacturer\"s instructions including dismantling, complete all as specified and directed. |
| 87 | S&F for 4mm thick designer ceiling boardin ceiling fixed with screw as per manufacturers instructions, laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white.The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheetof size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres.Hangers of GI wire 4 mm dia to be fixed by approved rawl plug or hanged with existing truss members. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modulescross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per instructions including dismantling of existing board etc, complete all as specified and directed. |
| 88 | Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions including Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equalflanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including dismantling of existing board, complete all as specified and directed. |
| 89 | S&F in repair supeior quality venetian blinds horizontalor vertical type (colour/ Design as approved by Engr-in-Charge at site) including powder coated hardware fittings, complete all as specified and directed by Eng-in-Charge |
| 90 | Taking down old GI tubing 15mm bore, cleaning for refixing or removing to store, complete all as sepcified and directed. |
| 91 | M&L for 15 mm bore galvanized iron tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors, complete all as specifed and directed. |
| 92 | Fixing only for 15 mm bore galvanized iron tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors, complete all as specifed and directed. |
| 93 | Taking down old GI tubing 20mm bore, cleaning for refixing or removing to store, complete all as sepcified and directed. |
| 94 | M&L for 20 mm bore galvanized iron tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors, complete all as specifed and directed. |
| 95 | Fixing only for 20 mm bore galvanized iron tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors, complete all as specifed and directed. |
| 96 | S&F in repair 15 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in new or old position, complete all as sepcified and directed. |
| 97 | S&F in repair 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in new or old position, complete all as sepcified and directed. |
| 98 | S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 500 ltrstank and making connections inlcuding suitable GI wash out, over flow, nipple and20mm bore ball brass valvewith union screwed for iron pipe and fixed including dismantling of old unserviceable tank, complete all as specifed and directed.Note:- The water tank shall be double layered IS marked duly embosed on face and weight as per IS specification. |
| 99 | S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrstank and making connections inlcuding suitable GI wash out, over flow, nipple and20mm bore ball brass valvewith union screwed for iron pipe and fixed including dismantling of old unserviceable tank, complete all as specifed and directed.Note:- The water tank shall be double layered IS marked duly embosed on face and weight as per IS specification. |
| 100 | S&F in repair for vitreous china wash hand basin white, flat back, size 550x400mm size including pedestal, cutting for and pinning ends of brackets or erecting stand, complete all as specified and directed. |
| 101 | S&F in repair forviterous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) and inlcuding set of CP jet with PVC pipe of superior quality, completeall as specified and directed. |
| 102 | S&F in repair Plastic water closet seat,white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed. |
| 103 | S&F in repair for 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float, 32mm bore PVC flush pipe and handle including brackets, completeall as specified and directed. |
| 104 | Fixing only flushing cisternafter repairing the old one retrieved from repair work, complete all as specified and directed. |
| 105 | S&F in repair viterous China urinal half stall type white including CP spreader holding screws , waste pipe etc, complete all as specified and directed. |
| 106 | S&F in repairwater closet pedestal pattern coloured with soft seat cover and twin flushing cistern (as approved by Engineer-in-charge), complete all as specifed. Make: Cera cat part no. EWC S1012135 (soft seat cover B15002 & Twin flush cistern 2205/BT Cruse)/ Jaquar cat part no. LYS-WHT-38751S250UFSMZ / Kohler white cat part no. K-21924X-S-WK. |
| 107 | S&F in repair vitreous China coloured, counter top wash hand basin, oval type, white, size 665x495mm including cutting for and pinning in, complete all as specified and directed. Make: Cera cat part no. WHB-S2031032/ Jaquar cat part no. ASC-WHT-87701/Kohler 25531W. |
| 108 | S & F in repairs for sink without draining board madeout of stainless steel 0.8mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm bowl size 410mm x 330 mm x 160mm complete all as specified and directed. |
| 109 | S & F in repair for 15mm bore brass chromium plated centre hole basin mixer with round spout including 450mm long PVC pipe with brass nuts without pop up, complete all as specified and directed. Make: Cera cat part no. F1015451/ Jaquar cat part no. CON 167KNB/Kohler 16231D-40. |
| 110 | S & F in repair for 15mm bore brass chromium plated wall mixer with connection to the over head shower arrangement, with 115mm long bend pipe on upper side, connecting legs & wall flanges, complete all as specified and directed. Make: Cera cat part no. F1015401/ Jaquar cat part no. CON 273KNUPR/Kohler 98755 W-Y-CP. |
| 111 | S&F in repair for 15mm bore wall mixer with telephonic bath shower arrangement with connecting legs, wall flanges & wall bracket for hand shower, complete all as specified and directed. Make: Cera cat part no. F1015414/ Jaquar cat part no. CON-267KN/Kohler 19561D. |
| 112 | S&F in repair telephonic hand shower 100mm round shape single flow (ABS body chrome plated with gray face plate) with rubit cleaning system including 15mm bore braided hose for telephonic hand shower, complete all as specified and directed. Make: Cera cat part no. F7030101/ Jaquar cat part no. HSH1937/Kohler 12861NZZ-CP. |
| 113 | S&F in repair 15mm bore angular stop cock with wall flange, complete all as specified and directed. Make: Cera cat part no. F1015201/ Jaquar cat part no. CON-059KN/Kohler K801541N. |
| 114 | S&F in repair for 15mm bore bib tap cast copper alloy chromium platedwith crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, complete all as specified and directed. Make: Cera cat part no. F1015151/ Jaquar cat part no. CON-037KN/Kohler 160931N. |
| 115 | S&F in repair for 15mm bore long body bib tap cast copper alloywith capstan head chromium plated, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed. Make: Cera cat part no. F1015151/ Jaquar cat part no. CON-107KN/Kohler 160931N. |
| 116 | S&F in repairPVC connection 15mm bore 450 mm long Braided Hose with M10X1 Nipple, 15 mm Nut, O-Ring & Rubber washer suitable for basin mixer, complete all as specified and directed. Make:- Jaquar cat part no. ALD-803AB/ Kohler/ Cera |
| 117 | S&F in repair PVC connection 15mm bore 450 mm long Braided Hose with two 15 mm Nut, & Rubber washer without nipple, complete all as specified and directed. Make: Cera cat part no. F8070402/ Jaquar cat part no. ALD-805B/Kohler |
| 118 | S&F repair forPVC connection pipe 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, completeall as specified and directed. |
| 119 | S&F in repair Hand shower ( health faucet ) with 8mm dia 1.2 meter longflexible braided chromium plated tube with wall hook, complete all as sepcified and directed. Make: Cera cat part no. F8030103/ Jaquar cat part no. ALD-573/Kohler 981001N. |
| 120 | S&F in repair for glass shelf assembly 550mm long with chromium plated bracket guard and rainling, complete all as specified and directed. Make: Cera cat part no. F5001114/ Jaquar cat part no. ACNAQN 7771/Kohler K12158-BN. |
| 121 | S&F in repair for soap dish holder, complete all as specified and directed. Make: Cera cat part no. F5002106/ Jaquar cat part no. ACN-1131N/Kohler 1216T0. |
| 122 | S & F in repair towel ring square with round flange, complete as specified and directed. Make: Cera cat part no. F5002105/ Jaquar cat part no. CAN-1121N/Kohler SS-304. |
| 123 | S & F in repair Toilet paper roll holder, complete as specified and directed by Engr-in-Charge. Make: Cera cat part no. F5001109/ Jaquar cat part no. ACN-1155S/Kohler K-5633IN-CP. |
| 124 | S & F in repairs towel rack 600mm long without lower hanger but with three hooks, complete all as specifed and directed. Make: Cera cat part no. F5003101/ Jaquar cat part no. ACN-1181FHS/Kohler SS304. |
| 125 | S & F in repair corner glass shelf with tempered glass, with chromium plated rails and bracket, complete all as specified and directed by Engr in Charge. Make: Cera cat part no. F5005101/ Jaquar cat part no. ACN-1173/Kohler KEA18846CH. |
| 126 | S&F six peg set with 4 mm thick base plate stainless steel fixed with and including rowel plugs and stainless steel screws, complete as specified and directed. |
| 127 | S&F in repair for 15mm bore pillar taps, cast copper alloy, with capstan heads, brass chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, completeall as specified and directed. |
| 128 | S&F in repair self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader, complete all as specified and directed. Make:- Cera/ Jaquar/ Kohler |
| 129 | S&F in repair 40 mm dia PVC waste pipe for WHB/sink (Min weight 45 to 60 gms), complete all as sepcified and directed. |
| 130 | S&F in repair for 32 mm bore waste coupling, chromium plated, full threaded with 80 mm long including washers, complete all as sepcified and directed. |
| 131 | M&L in repair for looking mirror 6mm thick of selected quality glass of size at required at site (area of each mirror exc 0.3 Sqm), duly bevelled edges with and including stainless spacer (04 no. spacers on one glass) (as approved by Engr-in-Charge), completeall as specified and directed. |
| 132 | S&F in repair 15mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as sepcified and directed. |
| 133 | S&F in repair 20mm dia Ball valve high pressure of PTMT with epoxy coated, aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as sepcified and directed. |
| 134 | S&F in repair PVC \"S\" trap 110 mm bore (SWR) fixed and jointed, complete all as specified and directed. |
| 135 | S & F in repairs for PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. |
| 136 | S & F in repairs for PVC (SWR) pipes 75mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. |
| 137 | S & F in repairs for PVC (SWR) pipes 75mm bore, single socketed, in any length with rubber ring joints fixed to walls with MS clamps of suitable size, complete all as specified and directed. |
| 138 | S & F in repairs for PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints fixed to walls with MS clamps of suitable size, complete all as specified and directed. |
| 139 | S & F in repairs PVC (SWR) bends of any radius with oval access door of 110mm dia completeall as specified and directed. |
| 140 | S & F in repairs PVC (SWR) bends of any radius with oval access door of 75mm dia completeall as specified and directed. |
| 141 | M & L in repair for 75 mm dia floor trap, with grating including jointing to waste pipe with solvent cement, complete all as specified and directed. |
| 142 | S & F PVC (SWR) bends of any radius of 110mm dia with solvent cement, complete all as specified and directed. |
| 143 | S&F in repair for PVC (SWR) junction double (single T) of size 110mm bore jointing with solvent cement, complete all as specified and directed. |
| 144 | S&F in repair for PVC (SWR) reducer 110mm to 75mm bore jointing with solvent cement, complete all as specified and directed. |
| 145 | S&F PVC (SWR) bend any radius of 75mm bore, complete all as specified and directed. |
| 146 | M&L for textured painting (granular or impression type) of any color, design in any position including base coat primer and surface preperation, complete all as specified and directed. |
| 147 | M&L for preparationof old or new surfaces including removal of old treatment and applying a thin layer of plaster of parris to give a uniform finish, complete all as specified and directed. |
| 148 | M&L for preparation of old or new surfaces including removal of old treatment and applying a thin layer up to 2 mm thick of putty to give a uniform finish, complete all as specified and directed. |
| 149 | M&L for Cornice with plaster of paris of appropriet design (as approved by Engr-in-Charge) as in corners, complete all as specified and directed. |
| 150 | M&L for complete removal of existing treatment on wall/ceiling surface including cornices and chajjas etc and applying two coats of exterior emulsion weather coat paint (as approved by Engr-in-Charge) after preparation of old or new surface, complete all as directed and as approved. |
| 151 | M & L for preparation of new plastered surfaces of walls/ ceilings and applying two coats of plastic emulsion paint of any shade as approved by Engr-in-Charge over a coat of primer, complete all as specified and directed . |
| 152 | M&L for complete removal of existing treatment of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer including preparation of surface, complete all as specified and directed. |
| 153 | M&L for preparation of old plastered surface of wall and applying one coat of oil bound distemper, complete all as specified and directed. |
| 154 | M&L for preparation of new plastered and unplastered wall surfcace and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed. |
| 155 | M&L for preparation of old plastered wall surfcace and applying one coats of cement base paint, complete all as specified and directed. |
| 156 | M & L for preparation of new steel and iron surfaces over 10cm width or girth and applying two coatsof synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. |
| 157 | M & L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed. |
| 158 | M & L for preparation of old wooden surfaces over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
