|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing), rubbish off the premises complete all as specified and directed. |
| 2 | Material & Labour 25mm thick PCC 1:2:4, type B-0 using 12.5mm graded crushed stone aggregate as in sub floor finished surface for laying tiles complete all as specified and directed. |
| 3 | M&L for Non - skid/matt finished coloured Ceramic tiles8 to 10 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchincluding 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and directed. |
| 4 | M&L for 7mm thick non skid coloured ceramic tiles (area of each tile exc 0.06 andn exc 0.11sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and directed. |
| 5 | S&F 10 to 12 mm thick endura tiles/outdoor tiles of size 300x300mm/400x400 mm set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and directed. |
| 6 | Demolition of cement concrete (un reinforced ) in ground floors and pavings n.exc 15cm thick (below or above ground level ) and removing debris ouside MD land complete all as specified and directed. |
| 7 | Demolition of brick work/ block masonry or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 8 | M&L for precast cement concrete block masonry type C-1 (1:3:6), using 20mm graded crushed stone aggregate, set and jointed in cement mortar 1:6 complete all as specified and directed. |
| 9 | M&L for 75mm thick PCC 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub base or floor complete all as specified and directed. |
| 10 | Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members complete all as specified and directed. |
| 11 | M&L for 6mm thick teak wood finish veneered ply board, solid core, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed to walls/ceiling of any description fixed with screws to timber frame work, complete all as specified and directed. |
| 12 | M&L in repair for 2nd class softwood clean sawn as in scantling fixed with nails exceeding 13 Sqcm and n.exc 25 Sqcm in section complete all as specified and directed. |
| 13 | M&L for polishing for the following steps against item No 11 above-(a) Surface Preparation : All wood surface shall be must be clean, firm and dry, remove any oil, greese, mortar dropping etc sand in the direction of grain to a smooth finish with 150 followed by 220 grit paper and remove dust with a damp cloth.(b) Filler : Use a coat oil based wood filler alllow to dry for 24 Hrs and remove the excess using 220 grit emery paper and wipe with dry cloth.(c) Stain the wood : Adding stain to bare or stripped wood can change the colour and highlight the grain pattern of any interior wood. Apply wood stain by rubbing or brushing aganist the direction of the grain will be help fill deep pores with stain. Apply a libral amount of stain giving up the wood an ample amount to abosrb. allow to dry 30 to 60 mins.(d) Apply touch wood polish two coats allowing 15-20 minutes between coats.Note : Any additional coat of wood polish required to achieve the requisite finish is included in the quoted rates. |
| 14 | Taking down shutter of any description exc 1 Sqm and not exc 2 Sqmcomplete all as specified and directed. |
| 15 | Taking down chowkhat or frames not exc 1.50 Sqm(without taking down shutters from the frames) complete all as specified and directed. |
| 16 | S & F 35mm thick 2nd class softwood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and directed. |
| 17 | M&L for IInd class Hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. |
| 18 | M&L for 2nd class hard wood 25 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc,sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied and fitted to chowkat complete all as specified and directed. |
| 19 | S&F 3 mm thick sheet glass, ordinary quality in square or rectangular not exc 0.50 Sqm in each pane fixed as per instructions of manufacturer complete all as specified and directed. |
| 20 | S&F 200mm long aluminium anodised barrel tower bolt of extruded section in old or new position complete all as specified and directed. |
| 21 | S&F Aluminium alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 22 | S&F aluminum door handle cast type 150 mm as in old or in new position complete all as specified and directed. |
| 23 | S&F 100mm long mild steel medium weight butt hinges cold rolled complete all as specified and directed. |
| 24 | S&F 100mm long aluminium anodised barrel tower bolt of extruded section in old or in new position complete all as specified and directed. |
| 25 | S&F aluminum door handle cast type 100 mm in old or in new position complete all as specified and directed. |
| 26 | S&F 75mm long mild steel medium weight butt hinges cold rolled complete all as specified and directed. |
| 27 | M&L for two coat of synthetic enamel paint over a coat of wood based primer including preparation of new wood surfaces complete all as specified and directed. |
| 28 | Dismantling plain or corrugated steelsheeting any gauge thickness including nanital or similar pattern complete all as specified and directed. |
| 29 | S&F 0.63 mm thick galvanised mild steel sheets with two corrugation side lap in curved shape fixed with J or L hooks with zinc coating of grade 275 complete all as specified and directed. |
| 30 | S&F rolled section as in main and cross beams, hip and jack rafters, purelins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates of Fe -410 Gde E-250 complete all as specified and directed. |
| 31 | Dismantling structural steel work including doors and gates of any description and in any position complete all as specified and directed. |
| 32 | M&L for two coats of synthetic enamel paint on new /previous untreated steel surface including preperation over a coat of red oxide zinc chrome primer complete all as specified and directed . |
| 33 | M&L for two coats of comofluge paint on new or old untreated steel sheet surfaces including preparation over a coat of red oxide zinc chrome primer complete all as specified and directed. Note:- Tint, make and pattern of paint shall be approved by GE. |
| 34 | Taking down carefully the existing aluminium/copper point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets, ceiling rose, fanregulators, lamp holders, call bell, bell pushes any type etc by unscrewing and taken away from site complete and make good the disturbed surface as existing complete all as specified and directed. |
| 35 | Taking down sheet metal enclosure DBs, main switch board etc and making good distrubed surface to match with existing surface complete all as specified and directed. |
| 36 | M & L for point wiring with 1.5 sqmm (nominal Area) FRLSH PVC insulated unsheathed multi stranded copper conductor, 1100 Volts grade, in and including PVC casing capping/conduit(ISI marked)with accessories such as bends, cross, elbow, tees etc. of suitable size including concealedPVC/MS pressed steel cadmium plated terminal box not less than 1.6 mm thick for mounting switches, sockets, fan regulators etc and 3 mm thick laminated sheet top cover(ISI marked) including continuous earth wire FRLS PVC insulated unsheathed 1.5 Sqmm (nominal area) copper multistranded conductor, 1100 Volts grade, connecting to common earth and earth dolly complete all as specified for one light point/Exhaust fan point controlled by one switch. |
| 37 | All as per item No 36 above but for one three pin socket outlet on same board complete all as specified and directed. |
| 38 | All as per item No 36 above but for one three pin socket outlet 5 amps on independent board complete all as specified and directed. |
| 39 | All as per item No 36 above above but for 3 pin 15 amps socket outlet on independent board with 2.5 sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 sqmm stranded copper conductor cable as continuous earth wire, complete all as specified and directed. |
| 40 | S&F Switch piano flush type single pole one way 5A SP 230 Volts complete all as specified and directed. |
| 41 | S&F Socket outlet 2 in 1, 3 pin 5 Amps Flush type complete all as specified and directed. |
| 42 | S&F Switch Socket combination outlet 2 in 1, 3/5 pin 5 and 15 Amps flush type complete all as specified and directed. |
| 43 | S&F Ceiling rose surface bakelite type 3 terminals 65x20mm complete all as specified and directed. |
| 44 | S& F in repair sheet metal enclosure, TPN, DB, 4 way, 415 V powder coated, for MCB to be used complete all as specified and directed. |
| 45 | Supply and fix in repair MCB, SP 06 to 40 Amps 10 KA \"C \" Curve complete all as specified and directed. |
| 46 | S & F in repair MCB, TPN,63A capacity, 10 KA C- curve, 415 V complete all as specified and directed. |
| 47 | S & F in repair surface and wall mounted LED tube light fitting integral type 1x20W, 230V, connector block etc completewith all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.Make:- Havells Cat Part No. LUMILINEPLUSBS20WLED865SPCS or equivalent in Bajaj /CG/ philips/Halonix/Wipro |
| 48 | Supply, installation, testing and commissioning bus chamber factory made Outdoor type, CPRI approved, size 0.45mx0.75mx0.4m deep,fabricated out of 3.15 mm thick mild steel sheetand vermin proof with neoprene gasket having front opening and locking arrangement mounted on angle iron legs made out of angle iron size 40 mm x 40 mm x 6 mm, 8.0 mtr long, 0.40 mtr above ground level and 0.40 mtr embedded in PCC 1:2:4 type \"B\"-1 using 20mm graded crushed stone agreegate blocks of size 0.30 mtr x 0.30 mtr x 0.50 mtr- 04 Nos, duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete with 200 Amp rated aluminium bus bar, LED three phase indicators, suitable for 3 phase 4 wire supply system with MCCB 125 Amp 4 polebreaking capacity 25 KA -01 No, duly drilled holes for cable connection mounted on epoxy based post insulators are all as required and deemed to be included in quoted rate, complete all as specified and directed. |
| 49 | S & F in replacement XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm 4 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing complete all as specified and directed. |
| 50 | Excavation in trenches n.exc 1.5 metres wide and n.exc 1.5 metres deep and getting out in any type of soil, for laying of cables/pipes complete all as specified and directed. |
| 51 | Returning filling in including spreading leveling, watering and well ramming in layers n. exc 25cm, complete all as specified and directed. |
| 52 | Removal of excavated material to be distance n.exc 50M and depositing where directed at a level n.exc 1.5m high from the starting point, complete all as specified and directed. |
| 53 | Supply and laying in replacement unreinforcedprecast concrete cable cover class LV type I flat size 250x150x40mm complete all as specified and directed. |
| 54 | M & L for Sand cushioning to under ground cables, 8 cm thick layer before laying and testing the cable and 15 cm thick after laying of cable complete all as specified and directed.Note:- Punned thickness of 18 CM shall be measured and paid under this item. |
| 55 | M & L for GI light grade pipe of 50mm dia with all fittings, laid in trenches, across road or pole complete all as specified and directed. |
| 56 | M & L forEarthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15 mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixingarrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electricalplate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.NOTE :- Item of earthing includes the cost of 7.5 metre long galvanised iron pipe and earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work. |
| 57 | M & L for Earthing complete with galvanised steel earth plate electrode 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised Iron Strip 25x4 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified & directed by Engr-in-ChargeNOTE :- Item of earthing includes the cost of 7.5 metre long galvanised iron pipe and earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work. |
