Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 09-01-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 16-01-2025 |
| 2 | 24-12-2024 | Corrigendum 2 | Date | 09-01-2025 |
| 3 | 18-12-2024 | Corrigendum 1 | Date | 02-01-2025 |
| Sl. No. | Item Description |
| 1 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in floors (other than ground floors),roofs, beams, columns, staircases, landing, chajjas,shelves and similar suspended workcomplete all as specified and directed . Note:- Proper precaution to be taken to avoid damage to floor slab from free falling of debris/concrete while demolition of roof slab. A layer of tyre of vehicles followed by covering of floor slab by wooden planksbe used to absorb shock of free falling debris/concrete.The quoted rate shall be deemed to include the cost of all precausionery measures. |
| 2 | M&L for providing Reinforced cement concrete M-30 (design mix), (using 20mm graded crushed stone aggregates) as inslab supported on walls, beams, columns,landings,balconies, canopies,deck slabsand in shelves and other similar workscomplete all as specified and directed and directed . |
| 3 | M&L for providing Reinforced cement concrete M-30 (design mix), (using 20mm graded crushed stone aggregates) as inlintels over 1.5 mtr clear span, siesmic band,beams,cantilevers and similar workscomplete all as specified and directed |
| 4 | M&L for use and waste of form work tosoffits of suspended slab such as roof slabs, not exceeding 200mm thick, horizontal or slopingcomplete all as specified and directed . |
| 5 | M&L for Mild steel TMT bars 10mm dia and over , cut to length, bent to shape as required, including cranking, bending and binding with& including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed . |
| 6 | M&L forMild steel TMT bars5 mm dia and over upto& including 10mm dia, as in stirrups, spacers and binders,cut to length bent to shape requiredincluding cranking, bindingspirally for hooping for columns, hooking ends and bindingwithand including MS wire annealed not less than 0.9 mm dia or securining with clipcomplete all as specified and directed. |
| 7 | Demolition of Brickwork or stone/boulder masonry,built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 8 | M&L for brick work with sub class \"B\" bricks using old size bricks, straight or curved on plan exceeding 6m mean radius,built in cement mortar 1:6 complete all as specified and directed . |
| 9 | All as per Srl item No. 08 here-in-before but except bricks. |
| 10 | M&L for brick work with sub class \"B\" bricks using old size bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4complete all as specified and directed. |
| 11 | Taking down shutter of any description exc 1 sqmbut n.exc 2sqm each & refixing the shutter in same opening including easing and adjusting complete all as specified and directed. |
| 12 | Taking downchowkats or frames n.exc 1.5 sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed. |
| 13 | Taking downchowkats or frames exc 1.5 sqm but n. exc 4 sqm each with shutters (without taking of shutters from the frames) complete all as specified and directed. |
| 14 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and screw withdrawal strength of 2200 N (Face)and 1100N (edge), minimum compressive strength 58 N/ mm ² ,modules of elasticity 900 N/mm ² and resistance of spread of flame of Class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed.Note:- Variation in profile size of frame ±5mm is allowed and contractor\"s quoted rate is deemed to include the same . |
| 15 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and screw withdrawal strength of 2200 N (Face)and 1100N (edge), minimum compressive strength 58 N/ mm ² ,modules of elasticity 900 N/mm ² and resistance of spread of flame of Class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed.Note:- Variation in profile size of frame ±5mm is allowed and contractor\"s quoted rate is deemed to include the same . |
| 16 | S&F factory made 35 mm thick2nd class hard wood, plain, framed, panelled shutters (two panels) with lock rail and panel of BWP commercial plywood or 12mm thick veneered particle board with commercial veneering on both faces .The size of rail and stiles as per IS: 1003(Part-1),kiln seasoned and chemically pressure treated, fitted to chowkats complete all as specified and directed. |
| 17 | S&F factory made 35 mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars ,any numbers sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed . |
| 18 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows& other Frames / Chowkhat of size 45 x 85 mmcomprising of virgin polymer of K value 58-60 (suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and screw withdrawal strength of 2200 N (Face)and 1100N (edge), minimum compressive strength 58 N/ mm ² ,modules of elasticity 900 N/mm ² and resistance of spread of flame of Class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note:- Variation in profile size of frame ±5mm is allowed and contractor\"s quoted rate is deemed to include the same . |
| 19 | S&F Factory Made Solid PVC Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed. |
| 20 | S&F box type mild steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed by Engineer-in-Charge. |
| 21 | S&F factory made steel window with side hung shutters including box type hinges with steel handle and 2 Nos 150mm long mild steel tower bolt,fixing lugs etc complete with glazing bars dovetailed or welded complete all as specified and directed by Engineer-in-Charge. |
| 22 | S&F factory made steel window with side hung shutters including box type hinges with steel handle and 2 Nos 150mm long mild steel tower bolt,fixing lugs etc complete without glazing bars dovetailed or welded complete all as specified and directed by Engineer-in-Charge. |
| 23 | S&F galvanisedmild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanisedwire staples complete all asspecified and directed . |
| 24 | S&F 3mm thick, figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed |
| 25 | M&L for 4 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with wooden beads (supplied alongwith shutters) in squares n.exc 0.5 sqm each pane complete all as specified and directed. |
| 26 | S&F Aluminium anodised barrel tower bolts, 150 mm long of extruded section complete all as specified and directed. |
| 27 | S&F Aluminium anodised, cast type, handle 150 mm size complete all as specified and directed. |
| 28 | S&F aluminium alloy, anodised, sliding door boltof length 250mm with hasp and staple (bolt type) andfixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed complete all as specified and directed. |
| 29 | S&F 150 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 30 | S&F Mild Steel framed work such as grills, gratings etc. with ends of bars shoulderd and/or riveted, or forged into spikes, framed guard bars, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks,cooler stand,ladder and similar work conforming to Fe290, Gde-E-165 complete all as specified and directed. |
| 31 | M&L for preparation of new or previously untreatedwood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 32 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed . |
| 33 | S&F vitrified tiles 8 to 9 mm thick (square/rectangular),light shade polished,area of each tilenot exceeding 0.36 sqm, as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying finishes complete all as specified and directed . |
| 34 | S&F Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular)area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying finishes complete all as specified and directed . |
| 35 | S&F Glazed ceramic coloured tiles 450mmx300mmx7mm thick (colour and shade as approved) as in vertical surfaces such as skirting/dados etc, set and jointed in neat cement slurry & pointed in white cement with pigment to match the colour of tiles over & including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed . |
| 36 | Dismantling stone slabsof any description or thickness in floors, apron etc laid bedded and pointed in any mortar complete all as specified and directed . |
| 37 | S&F Machine cut kota stone slab in flooring 20-25mm thicklaid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,cutting and mirror polishing over and including 20 mm thick screed bed or bedding layer in cement mortar 1:4complete all as specified and directed. |
| 38 | M&L for mirror polishingon marble /granite/kota stone/ stone work wherever required to give high gloss finish and applying white/coloured cement with pigment to match the shade of kota stone in the joints complete all as specified and directed |
| 39 | M&L for taking down cement plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 40 | M&L for rendering 10mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed. |
| 41 | M&L for rendering 15 mm thick in cement mortar 1:6 on other than fair faces ofbrick work or concrete surfaces finished even and smooth without using extra cementcomplete all as specified and directed . |
| 42 | M&L for rendering 10 mm thick in cement mortar 1:4 onfair faces ofbrick work or concrete surfaces finished even and smooth without using extra cementcomplete all as specified and directed . |
| 43 | M&L for preparation of newly plastered or unplastered wall surfaces and applying three coats of white wash complete all as specified and directed . |
| 44 | M&L for preparation of newly plastered or unplastered surfaces of ceiling and applying two coat of distemper oil emulsion (white/tinted) after finishing the surfaces with a coat of wall care puttybyhand roller complete all as specified and directed . |
| 45 | M&L for complete removal of existing treatment ofold decorated surfaces of wall by brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of distemper oil emultion (white/tinted) after finishing the surfaces with a coat of wall care puttybyhand roller complete all as specified and directed. |
| 46 | M&L for preparation of newly plastered or unplastered surfaces of wall,soffits,fascia of chajjas,roof slab and applying two coat of cement base paint complete all as specified and directed . |
| 47 | M&L for complete removal of existing treatment of old decorated surfaces of walls by brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts, treating oil & greasy spots,filling depression to make smooth surfacesand applying two coat of cement base paintcomplete all as specified and directed. |
| 48 | M&L for complete removal of existing treatment of old decorated surfaces of walls by brooming down and scrapping down smoke soot, moulds, moss and efflorescent salts, treating oil & greasy spots,filling depression to make smooth surfacesand applying one coat of white wash complete all as specified and directed. |
| 49 | S&F anodised aluminium snap grid frame work for false ceiling of grid 605x605mm, complete all as specified and directed. Note:-Quoted rate of the item deemed to be included for taking down and refixing (as per existing)minor electric fittings and fixtures (if any) on the surface of ceiling |
| 50 | S&F hangers 6mm dia (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made of GI flat 40x3mm size & length 60mm andexpansion hold fasterners 12.5mm dia,40mm long complete all as specified and directed. |
| 51 | S&F 12mm thick gypsum board as in ceiling material reinforced with GI wire meshfor fixing in 605 mm x 605mm gridcomplete all as specified and directed .Note:- Frame work for ceiling shall be measured and paid separately |
| 52 | S&F Solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet having beading/border on top and on joints inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawings all as specified and directed . |
| 53 | S&F5mm thick PVC Sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing all as specified and directed . |
| 54 | Taking upor down 25mm dia GI/PVC tubing and connection including, cleaning for refixing or removal to storecomplete all as specified and directed . |
| 55 | Taking upor down 15mm dia GI/PVC tubing and connection including, cleaning for refixing or removal to storecomplete all as specified and directed . |
| 56 | Taking upor down 20mm dia GI/PVC tubing and connection including, cleaning for refixing or removal to storecomplete all as specified and directed. |
| 57 | M&L for Steel water tubing of 25 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etccomplete all as specified and directed . |
| 58 | All as per item No 57 here-in-before but except tubes. |
| 59 | M&L for Steel water tubing of 15 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etccomplete all as specified and directed . |
| 60 | All as per item No 59 here-in-before but except tubes. |
| 61 | M&L for Steel water tubing of 20 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etccomplete all as specified and directed . |
| 62 | All as per item No 61 here-in-before but except tubes. |
| 63 | S&Fin repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed . |
| 64 | S&F in repair Stop valve/angle ball, cast copper alloy,chromium plated, screwed down for high pressurewith crutch or butter fly handle,screwedboth endsfor ironpipe of 15mm bore complete all as specified and directed. |
| 65 | S&F in repair 15mm bore bib taps, cast copper alloy, chromium plated fancy typewith crytch or butter fly handle, screwed down of iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 66 | S&F brass CP basin mixer,15mm bore, for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed . |
| 67 | S&F in repair Vitreous china squatting pan, \"Orissa\" pattern, size 580x440 mm white, with integral foot rests, CI \"P\" or \"S\" traps 100mm & PVC flush pipes 32mm diaincluding connecting to trap and to flushing pipe, anti-syphonage pipe etc including all joints and making good to floor complete all as specified and directed. |
| 68 | S&F 10 litres PVC,valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed. |
| 69 | S&F in repair vitreous china counter wash basins, size 470x470mm, white flat back to be fixed on counter/ RCC slabincluding 32mm waste fittings, waste pipe, chromium plated with long screwed shanks & fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified & directed. |
| 70 | S&F Vitreous chinahalf stall Urinal of size 635x395x420mm,whiteincluding providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe andfixing automatic flushing cistern with brackets including flush pipe, grating, union for discharge pipe, PTMT waste coupling 32mm bore, Waste pipe PVC 32mm borecomplete all as specified and directed. |
| 71 | S&F chromium plated urinal spreaderfor fixing with 15 mm dia pipe complete all as specified and directed . |
| 72 | S&F PVC connection, 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 73 | S&F PTMT soap tray, any type, fixed to plugs with chromium plated brass screwscomplete all as specified and directed. |
| 74 | S&F in repair PTMT shelf fixed with and including chromium plated brass screw and plastic cleat complete all as specified and directed. |
| 75 | S&F600mmx900mm looking mirror of selected glass 5mm thickmounted on6mm thick AC Building board or commercial ply woodwith PVC/ wooden moulding beading fixed to wooden plugs with chromium plated brass screws and cup washers etccomplete all as specified and directed . |
| 76 | S&F Towel rail, 450mm long of PTMT, fixed with and including chromium plated brass screws and wooden and plastic cleats( minimum weight 170gms ) complete all as specified & directed |
| 77 | S&F in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 Ltr capacity,trippled layered, hoisted and fixed in positionincluding PTMT float valves, high pressure with epoxy coated aluminium rodand high density plastic ballscrewed for iron pipe and fixed in position including all necessary fittings complete all as specified and directed. |
| 78 | Dismantling CI/PVC pipe of 100 / 75 mm dia alongwith fittings ,below or above GL/laid in floors/fixed to walls jointed in cement mortarcomplete all as specified and directed. |
| 79 | S&F110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches/in floors/fixed to walls includingfixing clamps with nut and boltscomplete all as specified and directed . |
| 80 | S&FPVC (SWR)bends any radius ,110mm bore complete all as specified and directed. |
| 81 | S&F 100mm dia cast iron soil, waste and vent pipe, in any length with or without ears with cement joints, laid in trenches/in floors or fixed to walls complete all as specified anddirected . |
| 82 | S&F 75mm dia cast iron soil, waste and vent pipe, in any length with or without ears with cement joints, laid in trenches/in floors or fixed to walls complete all as specified anddirected . |
| 83 | S&FCI bends (any radius), diminishing pieces or tapers, bore of pipe 100 mm fitted with oval access door complete all as specified anddirected . |
| 84 | S&F in repair CI bends, diminishing pieces or tapers, bore of pipe 75 mm complete all as specified anddirected . |
| 85 | S&F in repairs Cast iron floor trap, long neck, 75 mm dia with stainless steel grating including jointing to waste pipe, fixed in cement concrete type B1, 1:2:4 complete all as specified and directed . |
| 86 | S&FPVC waste pipe, 32 to 40mm for WHB/Sink /urinal up to floor trap and fixed complete all as specified and directed. |
| 87 | S&Fin repaircast iron cowl 100mm bore,complete all as specified and directed . |
| 88 | Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material to a distance n.exc 100m from the starting point completeall as specified anddirected |
| 89 | Demolition of mud/soil/mud phuskain roof, any thickness including plastering and leaping (where full thickness removed or only a part there of ) anddisposal of retrieved material to a distance n.exc 100m from the starting point completeall as specified andspecified |
| 90 | M&L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in coping, benching of manhole, roof kerbs or mud stops, rounded or chamfered anglescomplete all as specified and directed. |
| 91 | M&L for 40mm thickPCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) with WPC as in padding courseand similar workson roof slab,levelling to achieve specific slope including slightly rounded or chamfered angles including necessary formwork ,finishing surfaceseven and smooth without using extra cement complete all as specified and directed. Note : WPC will be measured and paid separately |
| 92 | Supply only Liquid water proofing compound. |
| 93 | M&L for Roof Treatment as specified below and as directed :(a) Cleaning, washing of surface and removing all existing bitumen coatings/ APP membrane completely with intense wire brushing or high speed water jet. Surface should be free from any loose paint, dust or grease.(b)All cracks upto 3mm at corner joints, channels and parapets should be treated with crack seal and bigger cracks, damaged portions and hollow areas must be repaired with polymer modified cement mortars.(c)Applying one coat of PrimeSeal/ Epoxy Primer/ShaliUrethane BTD White diluted with potable water in the ratio of 1:1 and apply @ 0.40 kg/ sqm (0.20 kg BTD+0.20 Kg water)(d)Laying polyster reinforced fiber net/50 gsm Geotextile mesh, upto 300 mm on walls.(e)Applying three coat of HydroShield PUD microfibre reinforced UV resistent polyurethane (solid content 68% ) / Damp Proof ultra UVStable fibre reinforced elastomeric liquid waterproofing membrane formulated with PU hybrid polymers (Solid content 55%)/ SmartCare PU Magnum elastomeric waterproofing coating based on hydrophobic polyurethane (solid content 85%)/Single Component Elastomeric Liquid Membrane ShaliUrethane BTD White/coloured(Elongation 400% ± 50, Solid Contents > 80% & Specific Gravity @ 30 OC 1.5 ± 0.03) @ total 2.00 Kg per sqm in two coats for maintaining thickness of 1.5mm,with paint brush/ roller upto 300 mm on walls.(f)) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer. Note : (i)The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer in Charge.(ii)The plan area of floor shall be considered for payment(iii)WPC shall be measured and paid seperately. |
| 94 | Dismantling stone slabsof any description or thickness in floors, apron etc laid bedded and pointed in any mortar complete all as specified and directed . |
| 95 | Demolition of concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and directed. |
| 96 | M&L for plain cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed. |
| 97 | M&L for hard core of gaugenot exceeding 63mmusing broken stone or boulders,deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed . |
| 98 | M&L for sand filling under floor with washed and screened dry fine river sand including watering, well ramming and consolidation complete all as specified and directed |
| 99 | M&L for Machine pressed Precast cement concrete interlocking coloured ( glossy finished / ruberised paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with and including 40mm thick sand cushining complete all as specified and directed . |
| 100 | M&L in repair Pre-cast cement concrete 1:2:4, type B1 (using 20mm graded crushed stone aggregates ) asin kerb stone, set in cement mortar 1:6. including necessary form work , excavation for embedding blocks in ground to depth as directed and finishing exposed surface even and smoothcomplete all as specified and directed . |
| 101 | M&L for preparation of newor previously untreated brick, stone, concrete or plastered and painting with two coats of synthetic enamel paint (white/golden yellow) over a coat of primer complete all as specified and directed. |
| 102 | M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) following the under layer with scratching tool, applying cement slurry on the under layer of cement @ 3 Kgper square metre and top layer 15mm thick in cement mortar 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Payment for providing grooves shall be made separately). |
| 103 | M&L for Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge. |
| 104 | M&L for Acrylic polymer base damp-proof coating system with two component ready to use acrylic polymer modified damp-proof coating shall be carried out as mentiond below complete as per specifications : (i). SURFACE PREPARATION: Remove the existing plastered surface with efflorescence/ seepage area. Non-moving cracks having width upto 5 mm must be filled with Polymer based crack filler.(ii). APPLICATION: Apply acrylic polymer base damp proof coating by brush roller over SSD surface. Apply the first coat of damp proof coating with a paintbrush directly on the surfaces. Allow to dry for a minimum 2-3 hrs. Apply subsequent second layer after drying. The first coat and second coat must be applied in perpedicular direction. The coverage must be atleast 1.2 sqm/kg/coat. The mixing for two component, if required, shall be done as per manufactures specifications. Rendering to be carried out after approval of Eng in charge and shall be paid seprately.Note : Treatment shall be carried out through Authorized applicators only |
| 105 | S&F Collapsible steel gates, top hung ,consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc as specified, erected in position and securing runners with holdfasts and brackets complete all as specified and directed. |
| 106 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed. |
| 107 | M&L for rolling and consolidating formation surfaces in cutting with 8 to 12 tonnes power rollers to required gradient and camber complete all as specified and directed . |
| 108 | M&L for Soling (or sub base) 100 mm thickusing broken boulders, quarried stone, inter stice filled,deposited, spread and surface formed, watered and rolled/rammed with 8 to 12 tonnes rollers , consolidated to required gradient and camber complete all as specified and directed . |
| 109 | M&L for PCC 1:1.5:3, type A2 (using 40mm graded crushed stone aggregates)as in floor etc finished even andsmooth complete all as specified and directed. |
| 110 | M&L for forming contraction(Dummy) joints 75mm deep x 10mm wide, filled with sealing compound of Grade \"B\" complete all as specified and directed . |
| 111 | Removal of surplus soil to a distance not exceeding. 50 m & depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed . |
| 112 | M&L for75mm thick cement concerete type D-2,1:4:8 using 40 mm graded stone aggregates as in subbase filling. Foundation and mass concreting of floors complete all as specified and directed by Engineer in Charge. |
| 113 | M&L for brick work with fly ash bricks using old size bricks, straight or curved on plan exceeding 6m mean radius,built in cement mortar 1:6 complete all as specified and directed . |
| 114 | M&L for RCC 1:1.5:3, type A1 (using 20mm graded crushed stone aggregates)as in slab supported on walls, beams, columns,landings,balconies, canopies,deck slabsand in shelves and other similar workscomplete all as specified and directed and directed . |
| 115 | Excavating in post holes each not exc 0.50 cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layer not exc 25cm and removing surplus soil to a distance not exc 50m and making good surface all as specified`and directed . |
| 116 | M & L for PCC 1:3:6) type C1 using 20mm graded stone aggregate as in bed plates to vertical posts etc, completeall as specified and directed by Engineer-in-charge . |
| 117 | Removing excavated material or surplus soil not exc 50 meter and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed . |
| 118 | S&F Roof trusses (framed), trussed, purlins, crane gantries rails and fastening and heavy bracket framing (beam, tee, angle channel or flat sections) including distance pieces, cleats etc confirmimg to Fe 290 (Gde E -165)complete all as specified and directed |
| 119 | M&L for preparation of new and previously un-treated steel surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 120 | S&F Pre painted galvalume aluminium zinc coating GI basedcorrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed . |
| 121 | Taking down carefully existing aluminium/copper point wiringfor light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells & making goodthe disturbed surfaces of walls, matching the colour with existing surface complete all as specified and directed.Note : Rate for making good shall be deemed to be included in above item rate. |
| 122 | Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLS with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit of suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of switches, sockets, fan regulator etc, covered with 2.8mm thick plastic laminate Hylem / Anchor top cover sheet of required colour, fixed with brass screws and cup washers, painting terminal boxes inside and outside with one coat of red oxide primerincluding continuous earth wire of size 1.5 Sqmm PVCstranded copper conductor unsheathed, insulated, stranded (Green colour) connected to common earthpoint dolly for forone light point/fan point/call bell point, 230 voltscontrolled by one switch complete all as specified and directed . |
| 123 | All as per Ser item No 122 here-in-before but for switch socket combination 5 Amp 5 Pin socket outlet230 volts on same board with other switches complete all as specified and directed . |
| 124 | All as per Ser item No 122 here-in-before but for switch socket combination 5 Amp 5 Pin socket outlet230 volts on independent board complete all as specified and directed . |
| 125 | All as per Srl item No. 122 here-in-beforefor Switch socket combination (multi purpose) 6 Pin 15 Amps 230 volts point to be controlled by one switch and wiring with 2.5Sqmm FRLS PVC unsheathed copper conductor andFRLS cable 2.5 Sqmm PVC insulated earth wire on independent board.complete all as specified and directed . |
| 126 | S&FPVC Lamp holder with back plate suitable for LED 5 to 20 watt bulb / batten fittingscomplete all as specified anddirected . |
| 127 | S&F LED bulb 1 x 10 watt Lamp having luminous efficiency warranty 2 years complete all as specified and directed . |
| 128 | S&Fcomplete set of tube light fitting, 1x20 watt LED (4 feet long),230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. |
| 129 | S&F complete set of tube light fitting, 1x10 watt LED (2 feet long),230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, LED tube, internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. |
| 130 | S&F ceiling rose, threeterminals, PVC polycarbonate, isolated body with bakalite 20mm back plate complete all as specified and directed . |
| 131 | S&F Sub main wiring with two runs of single core PVC FRLS sheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated FRLS copper wire 6 Sqmm for continous earth wire drawn into existing PVC concealed conduit complete all as specifiedand directed Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductorshall be measured as one length) |
| 132 | S&F in replacement Modular switch 1 way 6 amps, one modulecomplete all as specified and directed. |
| 133 | S&F in replacement Modular socket 6A /16A - 2/3 pin combined, 2 modulecomplete all as specified and directed. |
| 134 | S&F in replacement Modular switch 1 way 16 amps, one modulecomplete all as specified and directed. |
| 135 | S&F in replacement Modular socket 6A / 16A -2/3 pin combined, 2 modulecomplete all as specified and directed. |
| 136 | S&F in repairfactory made epoxy polyester powder coated distribution board TP&N ,4 ways (VTPN DB), double door,(concealed flush to wall) (IP-42 protection) fabricated from minimum 1.2 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 250 Amps bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with space for provision for 4 pole MCCB as incommer and outgoing MCBs as required at siteand conforming to IS: 8623 along with cable end box including making good disturbed surface complete all as specified and directed. NOTE: (a) MCCBs and MCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of BoQ. |
| 137 | S&FSheet metal enclosure for DBs,SPN, double door, 230 Volts,12 ways with 200 amps rated bus bar complete all as specified and directed . |
| 138 | S&F MCCB 4 Pole,adjustable type ,415 V, 100 Amps with breaking capacity 16 KA complete all as specified and directed. |
| 139 | S&F MCB SPN 40 amps 240V \"B\" curve with breaking capacity 10 KA in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 140 | S&F MCB SP 40 amps 240V \"B\" curve with breaking capacity 10 KA in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 141 | S&F MCB SP 5 to 32 amps 240V \"B\" curve with breaking capacity 10 KA in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 142 | M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, buried directly in ground vertically (depth of pit not less than 2.25m below normal ground level), with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to electrical equipment/GOD/LA and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI medium grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of precast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Schedule Part-I (2009), complete all as specified and directed. Note(s):- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with TMT bar 8mm dia both ways @100c/c.(ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m, excess beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) Quoted lump sum / rate shall be inclusive of above all provisions. |
| 143 | Excavation in trenches in any type of soil not exceeding 1.5m deep and 1.5m wide, for foundation etc or manholes,piers,shafts etc not exceeding 10 Sqm on plan orfor laying cables/poles foundation / stay assembly etcand getting out complete all as specified and directed. |
| 144 | Returning, filling in,including spreading, leveling, watering and well ramming in layers not exceeding 25cmcomplete all as specified and directed . |
| 145 | M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment. |
| 146 | Supplying and laying,factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dryin trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed. |
| 147 | Supply, laying, jointing, testing and commissioning of Low Tension (LT)XLPEinsulated,armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm, 4 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, alongpolesorpassing through pipes or laid under floor or through walls etc, including taking out existing one completeall as specified and as directed. Note:(i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately. |
| 148 | S&F in repair energy efficient LED Security light fitting of 25W, pressure die cast aluminium housing/body, heat resistant clear toughened glass, better optics for uniform distribution street/ roadway luminaire, with driver including electric connection, complete fitting with all accessorieson andincluding bracket of 40mm dia,light grade ,GI pipe ,1.20 m and connecting with twin core twisted flexible copper conductor cable 1.5 Sqmmand with following specifications complete all as specified and directed :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt.(b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95(e) THD : Max15%.(f) IP rating : IP66. (g) IK rating:Minimum IK07 (h) Built in potted LED Driver of the same make as of the luminaire.(j) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI: Morethan 80 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12Hrs |
| 149 | M&L in repairfor Steel water tubing of 25 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etccomplete all as specified and directed . |
| 150 | S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 25 mm dia of pipe complete all as specified and directed. |
| 151 | M&L in repairfor Steel water tubing of 40 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etccomplete all as specified and directed . |
| 152 | S&Fin repair1X10 watt LED retrofit type bulk head fitting luminaries, die cast, aluminium alloy body, heat resistant, prismatic glass cover with specially designed gasket etc complete with all accessories and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 HZ complete all as specified and directed. |
| 153 | Supply & fixing Energy efficient Ceiling fan complete with blades, down rods, remote & accessories, 230 V,1200mm sweep, minimum air delivery 245 CFM with service value 6.00 BEE, 5 star rated with brushless direct current motor (BLDC)includingwriting of MES number (Black, Roman, Italic or Indian) n. exc 30cm height complete all as specified and directed. |
| 154 | Supplying and fixing and commissioning of electric water heater (Gyser) storage type ABS body of capacity 25 ltrs, BEE appreoved 5 star rating, 230V,single Phase, AC supply inner tank made out of heavy duty stainless steel sheet (Designed with single weld line, factory tested with hydraulic pressure as per latest IS code) with glass lined quoting complete with all accessories such as safety valve thermostate NRV, connection piece PVC connectionfor hot and cold water 3 core PVC insulated PVC sheated copper conductor flexible cable including 15 Amp plug suitable for existing socket and fixing material, 04 Nos nut bolt grouting in wall in PCC(1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and directed. |
| 155 | S&F exhaust fan ,steel body, AC single phase, 4 blades with self closing GI louver shutter suitable for operation on 220/230 volts of 300mm sweep andincluding three core copper flexible wire 1.00 mm diadrawn into and including PVC flexibleconduit andhanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long includingwall hole and making good the disturbed surfaces as per existingcomplete allas specified & directed. |
| 156 | S&F in repair PVC non metallic rigid conduit, 25 mm external dia (medium grade) ISI marked exclusive of boxes but inclusive of all tees, bends, reducer, bell mouth tube ends and fixing accessories, concealed including cutting chases in wall, floor and making good all disturbed surfaces matching with existing surfacescomplete all as specified and directed. Note :-A Sum of Rs. 19,136.00 will be deducted on account of credit for dismantling/ demolished/ taking down material. Please refer detail on srl page No. 30(Schedule of credit) of Tender Documents. |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
