Tender For Addn/ Altr In Bldg No A-47 (Or Cook House) At Dalhousie.; 1 Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out 2 Returning filling in including spreading, levelling,watering and well ramming in layers not exceeding 25cm thick. 3 Removal of surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point and disposal. 4 M & L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete etc. 5 Formwork to rough finished surfacesides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter in flat all as specified and directed 6 M&L for RCC M 25 (Design Mix) using 20mm graded crushed stone aggregate as in foundation,ncludings,footing, foundation, beams, plinth beam bases for columns,etc basement slabs mass concrete completed all as specified and directed. 7 Formwork torough finished surface sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. 8 M&L for RCC M 25 (Design Mix) using 20mm graded crushed stone aggregate as in beams ,cantilevers bressummers lintels over 1.50m spancomplete all as specified and directed 9 Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips 10 Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and bindersand over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips 11 Dismantling of brick work/stone work built in cement motor all as specified 12 M&L Brick work with old size fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge . 13 S&F 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork ,applying evenly a coat of blown type bitumen at the rate of 1.5kg/per sqm and binding with clean dry sand @ 0.05 cum per sqm, polythene film, 150 micron thick,laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sq.mtr complete all as specified and directed by engr in charge. 14 Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface 15 M&L 75 mm thick PCC 1:4:8 type D 2 using 40 mm gradedstone aggregate as in sub base all as specified and directed 16 M&L 25 mm thick1:2:4 type B 0using 12.50 mm gradedstone aggregate as in floor finishing cement concrete surface even and smooth withoutusing extra cement all as specified and directed 17 M&L machine cut kota stone slab flooring 18-20mm thick in single piece over cement screed base laid and jointed with grey cement mixed with pigment to match the shade of the slab including rubbing,polishing and chamfering the edges of stepsinculding screed bed or bedding layer of mortar 15 mm thick CM (1:6)all as directed by Engineer-in-Charge. 18 M & L forrubbing,polishing and chamfering on old Surface ofKota Stone Complete all as specified and directed by Engineer-in-Charge. 19 S & F.Glazed ceramic tiles in vertical surface 350 x250x 7 mm/ 450x 350x7 mmthick set and jointed in neat cement slurry and pointed in white or coloured cement to matchto the shade over 10 mm thick cement sand screed (1:3)complete allas specified. 20 M&L 75 mm thick cement concrete type C1 1:3:6using 40 mm gradedstone aggregate as in plith protection, surface finished even and smooth without using extra cement. 21 M & L form work to soffits of suspended slabs such as roof slab and similar work not exceeding 200mm thick for rough finished surfaces of concrete all as specified and directed by Engineer - in - Charge . 22 M & L form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs, horizontal or sloping and similar work exceeding 5cm but not exceeding 10cm wide for rough finished surfaces of concrete all as specified and directed by Engineer - in - Charge. 23 M & L RCC M-25 design Mix as in chajjas, fins, fascias,shelves ,Kitchen platformlouvers, parapets and railing etc and the like including necessary formworks all as specified and directed by Engineer - in - Charge. 24 M&L for 20mm thick Granite (of any type) work in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as secified and as directed. 25 S&Fpowder coated anodized aluminum frame for doors, windows , ventilators with one of more rebates including joining cleat for fixing etc. completed all as specified. 26 S&F anodised aluminium door shutter ,aluminium section wt 0.55 kg / mtr including necessary joining cleats ,glazing clips, rubber eoprene packing , handles 2 Nos. in each door , hinges , anodised aluminium snap beading screws etc. 27 Taking down chowkats with shutter n. exc 1.5 sqm each. (without taking of shutter from the frame) .all as specified & directed. 28 S & F in repair powder coated aluminum sliding window three track with frame & two glass shutter using 4 mm thick glass tinted modi guard and one shutter with stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm using aluminum powder coated section aluminum cleat , PVC track, bearing, handle lock rubber beading etc complete fittings as approved. Note :- Size of aluminum section shall be under – (i) three track top and vertical – jindal main 2010. Section No 20621 or equivalent as approved by AGE (I).(ii) Three track bottom – Jindal main – 2010 section 20620 orequivalent as approved by AGE (I).(iii)Shutter Vertical Section - Jindal main – 2010 section 20604 orequivalent as approved by AGE (I).(iv) Shutter top and bottom - Jindal main – 2010 section 20604 orequivalent as approved by AGE(I).(v) Shutter vertical middle ( interlock) - Jindal main – 2010 section 20605 orequivalent as approved by AGE(I).(vi) aluminum anodizedgrill diamond shape 100mm x 100mm aperture of 6 mm dia roundbars including necessary joining cleats, clips anodised complete all as specified. 29 S&FPowder coated aluminumventilators shutter side hung type without sash, aluminum section weighing glazed clips, rubber packing anodized aluminum fittings such as peg stays 150 mm long (1 nos)hinges type B-21 100 mm long (2 Nos) suitable handle (1 Nos) complete all as specified. 30 S&F sheet glassnot less than 4.8 mm thick ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 sqm in each pane 31 S & F galvanised stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm fixed with tinned tacks, or galvanised wire staples,fixed in repairsall as specified. 32 S&F in repairs door closer hydraulically regulated, aluminium (Die cast) body, designation No. 3, universal type suitable for door shutter upto 1000mm in width complete all as specified and as directed. 33 M&L in repairs AluminiumMotrice lock4 levers and 75mm size for aluminium doors 34 S&F for Alum door stopper of any descripion all as specified and directed by Engineer-in-charge. 35 Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each all as specified . 36 S&F IInd class hard wood (Sal, Hollock)plain solid, straight, Chowkat and frames, wrought, framed, rebated on the solid , rounded or chamfered, put togetherwith glue, pinned at joints complete all as specified. 37 S&F flush shutters, 35 mm thickness solid core construction, with block board core and ply wood face panels, commercial type on both sides complete all as specified. (Make : Swastik Ply Wood, Century Plywood or equivalent) 38 S & F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats all as specified. 39 S & F 150 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinges pin,anodised and fixed. 40 S & F Aluminium alloy, anodised, sliding door bolt 300mm with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudedsections or cast-aluminium alloy and fixed 41 S & F in repair MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete 42 S&F 18mm thick PVC sheet having one side decorative laminated sheet all required brackets SS screws etc. the panel shall be fabricated using adhesive and screws where ever required.all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification including fitting i.e. magnetic catcher,stainless steel handleapproved by Engineer -in-Charge. 43 S&F 125mm Hasp and staple, aluminium anodized, including bolt to hinge plate and fixed with screws 44 S & F continous piano hinges mild steel bright finish or galvanised of 30mm width 45 M&L for applying two coat of synthetic enamel paint over a coat of pink primer on new wood or wooden surfaces of any description over10cm in width or girth not otherwise described including preparation complete all as specified. (Make : Goodlass Nerolac Paints, Berger Paint, Asian Paints or equivelent) 46 M & L for preparation of old painted wooden surfaces of any description over 10 cm width of girth not otherwise described and applying one coat of synthetic enamel paintall as specified. 47 S&F 15 mm bore CP angle cock one way chromium plated, high pressure with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified. 48 S&F Aluminium anodized snap grid (powder coated) frame work of grid size 605x605mm including hangers 6mm dia GI (upto 1200mm long) for false ceiling including notching and preparing holes, including aluminium cleat/corner pieces and GI 4mm dia suspenders with utterfly clips, wall angle of size 24 x 24mm, main runner (teee) of size 24 x 38mm, cross tee of size 24 x 28mm, (No of suspenders shall be decided by the GE as per actual size requirement)Perforated particleboard/tiles of 10 mm thick for insula-tion puroses, as in ceilings flat or sloping 60x60 cm in size complete all as specified and as directed. 49 S & F in repair stainless steel plate rack of size of 900 mm x 775 mm x 250 mm made out of 1 mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge. Make Anupam internationalor Equivalent make and model approved by AGE(I). 50 S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm 51 S&F 15 mm bib taps, chromium plated fancy type cast copper alloy with crutch or butterfly hand, swrewed down, secrewed for iron pipe or for brass ferrule and fixed. 52 S&F 20 mm bore stop valve , cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both end of iron pipe or union and fixed all as specified. 53 S & F PVC connection 15 mm size with PTMT nuts of length 450 mm all as specified. 54 GI tubes medium grade 15mm dia, with all fittings and fixed complete to walls and ceiling or laid in floors all as specified.(Make : Jindal, TATA) 55 S & F of GI tubes medium grade 20mm dia with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor all as specified. 56 Dismantling water tank and removing to stores exc250ltr n.exc 500ltr all as specified & directed. 57 S & F rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 1000 Litres all as specified and directed by Engineer - in - Charge . 58 S&F 20 mm float ball valve high pressire of PTMT with epoxy coated aluminium rod & high density platic ball screwed for iron pipe and fixed. ( Min weight 15 mm - 142 gms/20 mm 210 gms/25 mm 455gms/40mm 690 gms) 59 S&F 110mm bore PVC (SWR) pipes single socketed inany length withrubber ring joints laid in trenches or in floors all as specified and directed. 60 M&L75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement 61 Taking down cement plaster/dado on brick wall/ stone masonary including racking out joints, hacking for keys scrubbing down with water all as specified. 62 M& L Rendering 15 mm thick on other than fair faces of brick work/ stone masonary or concrete surfaces in CM 1:6 finished even and smooth ( wihout using Extra cement) as in vertical surface all as specified and directed. 63 M&L Rendering 15 mm thick on fair faces of brick work/ stone masonary or concrete surfaces in CM 1:4 withwater proofing compound finished even and smooth ( wihout using Extra cement) as in vertical surface all as specified and directed. 64 S&F Rooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings,tank stagingand heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-410 W (Gde-E-250) quality B complete all as specified. 65 Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new pre primed surface. 66 M&L for dismantling CGI or PGI sheet of any gauge and thickness or any pattern roof covering complete all as specified. 67 S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 55p Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. 68 S&F pre painted galvalume aluminium zinc coating GI based plainsteel sheet 0.50 mm thick of an colour having tensile strength of 55p Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. 69 M & L preparing new plastered surfaces of wallsand applying two coats of cement base paint all as specified & directed. 70 M & L preparing new plastered surfaces of internal wallsand applying two coats of distemper oil emulsion over a coat of primer with 3mm thick wall care putty on wall all as specified & directed. 71 Taking down carefully existing copper/aluminium point wiring of any type (light/fan/socket or power) complete fixture and fittings such as switches ,ceiling rose, regulators,sockets etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per sch of credit) and making good disturbed surfaces of wall, floor, ceiling etc. 72 M & L for point wiring with copper conductor cable multistrand, PVC sheathed 1.5 Sqmm size for one light point controlled by one switch including one run of 1.5 Sqmm multistrand PVC unsheathed copper conductor cable for earth continuity inPVC Concealed conduit of approved size and qualityISI marked in Brick machinary/Stone machinary wall complete including cutting, chasing, pinning and making good the disturbed surfaces by using cement mortor 1:3 of wall by providing cement plaster and matching the surfaces by white wash/colour wash all as per existing finishes complete including all other required accessories as specified in Preamble 1(a) to (q) of section 19 of SSR Part-II under heading Point wiring.fixed on walls/ceiling including sunk cast ironterminal boxesgrouting/ flushing on wall for mounting fittings like switch, sockets etc covered with 3.00 mm thick plastic laminated sheet top covercomplete all as specified anddirected by Engr-in-charge. 73 All as per item no. 72 but for one fan point, exhaust fan point. 74 All as per Srl item No 72 here in before butfor one 5 amps socket out let on same board. 75 All as per Srl item No 72 here in before but for one 5 amps socket out let on independent board. 76 All as per item No 72 above but for power point 3 pin switch socket 15 Amp with PVC insulated copper conductor cable multistrand unsheathed 2.5 Sqmm on independent board including one run of1.5 Sqmm multistrand PVCsheathed copper conductor cable for earth continuity incocealed PVC conduit of appropriate size and best quality ISI marked, includingsuitable size of copper lugs and all other required accessories as specified in preamble 1(a) to (q) of Section-19 of SSR Part-II under heading Point wiringfixed on wall including sunk cast iron terminal boxes grouting/ flushing on wall for mounting fittings like switch, sockets etc covered with 3.00 mm thick plastic laminated sheet top cover all as specified and as directed. 77 Supply & Fixing Switch piano, flush button, single pole one way 6 Amps 78 Supply & Fixing Socket outlet 3 pin, 6 amps flush type. 79 Supply & Fixing Switch piano, flush button, single pole one way 16 amps 80 Supply & Fixing Socket outlet 2 in 1,3 pin 5 and 16 amps flush type. 81 Supply and fix in replacement ceiling rose 65X50 mmthree terminals with back plate complete all as specified. Make :- Anchor / Cona / Plaza / SSK 82 S & F in replacement of unserviceable Supply and fixing LED lights fitting 1x 20W,4 feet, 220V,AC decorative box type with driver, holder includingLED tube light connecting up with three core flexiblecopper conductor cable of suitable size from ceilingrose complete.Make- Havells cat part-LHEXACP7UN1W020 or crompton/wipro 83 Disconnecting/ Dismantling of electric Water Heater from site and keep it in safe custody and refix with same in its existing position after completion of work with supply and fix 04 nos hold fastner, nuts, bolts, washer and two nos of hot and cold 45/60cm long PVC water connection pipe etc including painting of geyser complete al as specified and as directed by Engr-in-Charge. 84 Disconnecting/ Dismantling of electric Exchaust fan of any size from site and keep it in safe custody and refix with same in its existing position after completion of work with supply and fix 04 nos hold fastner, nuts, bolts, washer etc complete al as specified and as directed by Engr-in-Charge. 85 Supply & Fixingin replacement Sheet metal enclosure for DB,s, double door(when MCB,s to be used) single pole & neutral 12 way with 200 amps rated bus bar 240 volts with fixing arrangements. Make- C&S/Havells/Indoasian/Legrand 86 Supply and fixing inreplacement MCB single pole and neutral6 to 32 Amps, 240 volts complete all as specified and directed. Make :- C&S/Havells/Indoasian/Legrand 87 Supply and fixing MCB single pole 6 to 32 Amps, 240 volts all as spd and directed. Make C&S, Havells, Legrand,L&T
