|
| 1 | Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. |
| 2 | All kinds of soil |
| 3 | Rubblepackingwithhardlateritestoneunder floors includingwatering rammingand consolidatingetc.inpipelinetrenchesandother foundations complete. |
| 4 | Providing&layingcementconcrete1:3:6(1 cement:3coarsesand:6gradedgraniticor basaltic stone aggrt. 40 mm. nominal size) excluding cost of centering, shuttering and finishing in: |
| 5 | All works upto plinth level |
| 6 | Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) |
| 7 | All works upto plinth level |
| 8 | Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member. |
| 9 | Centering&shutteringincludingStrutting, Propping & removal of forms for : |
| 10 | Foundations, Footings, Bases for columns |
| 11 | Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan) |
| 12 | Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement. |
| 13 | Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in superstructure from floor I level upto floor V level. |
| 14 | 12mm cement plaster 1:4 (1 cement : 4 fine sand) |
| 15 | 18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge. |
| 16 | 40 mm. thick red oxide flooring under layer of 30 mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 12.5mm nominal size) and top layer of 10 mm thick plaster of cement red oxide mix using 3.5 kg. Of red oxide of iron per 50 kg. of cement 1:3(1cement : 3 coarse sand) finished with floating coat of neat cement red oxide mix of same proportion. |
| 17 | Steel work in built up tubular (round, square or rectangularhollowtubesetc.)(SquareHollow Section (SHS) IS4923/RectangularHollow Section (RHS)IS4923/CircularHollowSection (CHS)IS1161closedStructuralSteelof(SAIL, TATA.VIZAG,JSW,APOLLOSteelLtd.)make (Min Yeild Stress 310 Mpa))trussesetc., including cutting, hoisting, fixing in position and applyingapriming coatofapprovedsteel primer,including weldingandboltedwith special shaped washers etc. complete. |
| 18 | Providingandfixingcolourcoatedgalvulium roofingsheetsof0.5mmthicknessincludingall theaccessories(TATAmake)butexcludingthe costofpurlins,rafters,trusses,flashingsetc. complete as per the directions of the Engineer in charge. |
| 19 | Addforproviding&fixingFlashings-[Corners, Ridges,valleys,gableend &Trims] (Girth upto 610mm)includingalltheaccessoriescomplete as per the directions of the Engineer in charge. |
| 20 | Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall |
| 21 | Distempering two or more coats with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade. |
| 22 | Painting three or more coats with acryllic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat of |
| 23 | Applying priming coat with ready mixed primer of approved brand and manufacture on steel work. |
| 24 | Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade. |
