Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 25-11-2024 | AMENDMENT IN BOQ FOR SPECIAL REPAIR TO BLDG NO T 23 OR LIVING ACCN IN E ZONE PROVN OF 03 X TOILET BLOCKS NEAR BLDG NO T 125 1 AND SPECIAL REPAIR TO BLDG NO OP T193 IN THE AREA OF AGE BR I AND BR II AT RMS | BOQ | 04-12-2024 |
| 2 | 25-11-2024 | AMENDMENT IN DATE FOR SPECIAL REPAIR TO BLDG NO T 23 OR LIVING ACCN IN E ZONE PROVN OF 03 X TOILET BLOCKS NEAR BLDG NO T 125 1 AND SPECIAL REPAIR TO BLDG NO OP T193 IN THE AREA OF AGE BR | Date | 04-12-2024 |
| Sl. No. | Item Description |
| 1 | Demolition of plain cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc complete all as specified and directed. |
| 2 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 3 | Taking down chowkhat or frames not exc 1.5 Sqm each (without taking off shutter from the frame) complete all as specifed and directed. |
| 4 | Taking down chowkhat or frames exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutter from the frame) complete all as specifed and directed. |
| 5 | Taking down shutter not exceeding 1 Sqm each etc complete all as specified and directed. |
| 6 | Taking downshutter of any descriptionexceeding 1.0 Sqmnexc 2Sqm each etc complete all as specified and directed. |
| 7 | Dismantling timber scantlings unframed work 40 sqcm and over in section in any position complete all as specified and directed. |
| 8 | Demolition of reed, lathing single or double, including battens and plaster or chicken wire lathing complete all as specified and directed. |
| 9 | Dismantling of chicken wire lathing complete all as specified and directed. |
| 10 | Disamantling wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness including cover fillets complete all as specified and directed. |
| 11 | Dismantling boarding any description fixed in any position with nails complete all as specified and directed. |
| 12 | Dismantling of wrought iron or mild steel work of any description etc complete all as specified and directed. |
| 13 | Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes laying of cable/ pipe holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft and loose soil etc complete all as specified and directed. |
| 14 | Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excl ashlar facing etc complete all as specified and directed. |
| 15 | M&L for PCC (1:4:8) Type D-2(using 40mm graded stone aggregate) as in foundation filling and mass concrete etc complete all as specified and directed. |
| 16 | M&L for brick work in cement mortar (1:6) using sub class \"B\" bricks (using old size burnt bricks) straight or curved on plan exc 6.0 m mean raidus etc complete all as specified and as directed. |
| 17 | M&L for brick work with sub class \"B\" bricks (using old size burnt bricks) straight or curved on plan in any radius in half brick thick walls built in cement mortar (1:4), etc complete all as specified and as directed. |
| 18 | M & L for PCC (1:4:8) type D-2, 75 mm thick (using 40 mm graded stone aggregate) as in sub base etc complete all as specified and directed. |
| 19 | M&L for damp proof course, (1:2:4) type B-0 as in 40mm thick(using 12.5mm graded stone aggregate)to horizontal or vertical surfaces including necessary formwork over & including applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and binding with clean dry sand @0.05 cum per sqm incl 150 micron thick polythene film laid over a coat of bitumen primer @ 0.30 to 0.50 kg per sqm etc complete all as specified and directed. |
| 20 | M&L PCCtype B-1, (1:2:4) (using 20mm graded stone aggregate) 25mm thick as in subbase levelling course of flooring finished even and fair using extra cement etc complete all as specified and directed. |
| 21 | Returning filling in including spreading leveling watering and well ramming in layers not exc 25 cm in soft/loose soil etc complete all as specified and directed. |
| 22 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point. |
| 23 | M&L for RCC as in beams, cantilevers, bressummers, lintels over 1.5m span using RCC Type B1 (1:1.5:3) (using 20mm graded stone aggregate) etc complete all as specified and directed. |
| 24 | M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with etc complete all as specified and directed. |
| 25 | M & L forMS TMT bars 6 mm to 8 mm dia cut to length, bent to shape reqd incl cranking, bending and binding with MS wire n.exc 0.90 mm dia (annealed) for stirrups/binders etc complete all as specified and directed. |
| 26 | Use & waste of Formwork to sides and soffits of lintels beam, cantilevers etc complete all as specified and directed. |
| 27 | S & F compound girders and stanchions, lattice girders aerialmasts, staging for water tank and the like incl caps, bases, splices etc built up from two or more beam or channel sections or angles with plates incl all lattice bars, stiffeners, gusset plates etc complete all as specified and directed |
| 28 | M&L for RCC (1:2:4) Type B1(using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabsetc complete all as specified and directed. |
| 29 | Use & Waste of formwork to chullah hood, chajjas troughs and similar items including edges etc complete all as specified and as directed |
| 30 | M & L for non skid ceramic tiles 7 to 8 mm thick (square/rectangular),area of each tilesexceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement with pigment to match shade of tiles,laid over and including 15 mm thick screed bed in CM (1:6)complete all as specified and directed. |
| 31 | All as per Ser items No 30.00 (here-in-before) but on vertical surfaces such as skirting , dado risers to stepsover and including 10 mm thick bedding layer in CM (1:4). |
| 32 | M&L for glazed ceramic coloured tiles of size 350x250x 7mm/ 450mm X 350mm x 7mm thick as in dado/skirting set and jointed in neat cement slurry and pointedin whitecement mixed with pigment to match shade of tiles over and including 10mm thick CM (1:4) backing coat etc complete all as specified and directed. |
| 33 | S&Fsteelworkintubulartrusses, post, purlinsincludingspecialshapedwasheretc.CompleteusingERWorinductionbuttweldedtubesconformingtoIS1161-1979gradest-240complete all as specified and directed by Engineer - in – Charge |
| 34 | M&L forRoof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410 -W (Gde-E- 250) quality-A etc complete all as specified and directed. |
| 35 | S & F for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde-E- 250) quality-B etc complete all as specified and directed. |
| 36 | S&F MS screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nuts, length of bolt exc 10cm andn Exc 15 cmlong dia of neck 11 to 15 mm etc complete all as specified and directed. |
| 37 | S&F MS screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nuts, length of bolt exc 15cm andn Exc 22.5 cmlong dia of neck 16 to 20 mm etc complete all as specified and directed. |
| 38 | M&L for preparation of newsurfaces of steel and iron work of any description over 10 cm width or girth not otherwise described andapplying two coats of synthetic enamel paint over a coat of redoxide primer on new surfaces in any tint etc complete all as specified and directed. |
| 39 | M&L for 2nd class hard wood scantling as in framed worketc clean sawn complete all as specified and directed. |
| 40 | All as per item No 39.00 (here-in-before) but except timber complete all as specified and directed. |
| 41 | S & F for4 mm thick of size 600x600mmHSPC (high pressure Steam Cured) pre-painted self embossed, textured designer boardE-Board Classic to be fixed or laid with GI frame grid/section size 600mm x 600mm with main runner 38x24x0.9 mm thick, cross tee 8.6x24x0.9mm and wall angle 19 x19x0.9mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both waysfixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified and directed. |
| 42 | M & L 25mm thick and 200 mm width second class hard wood boarding , plained one side with butt joints as ineaves boards complete all as specified and directed. |
| 43 | M&L for 75 mm thick PCC (1:3:6) type C-2 , (using 40 mm graded stone aggregate) in plinth protection laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed. |
| 44 | M&L for chequered cement concrete tiles 25mm thick laid over and including 15mm thick screed bed or bedding layer of mortar for laying floor finishes in cement mortar 1:6, etc, set, jointed and pointed in neat cement slurry with grey cement and pigments complete all as specified and directed. |
| 45 | M&L for 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pined joints complete all as specified and directed. |
| 46 | M&L for factory made 35mm thick 2nd class hard woodGlazed and skelton window and ventilatorshutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebatedwithout sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a)etc complete all as specified and directed. |
| 47 | M&L for factory made 30mm thick 2nd class hard woodGlazed and skelton window and ventilatorshutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebatedwithout sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b)etc complete all as specified and directed. |
| 48 | S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and directed. |
| 49 | M&L butt hinges medium grade cold rolled mild steel and fixed size of hinges 100 mm long size etc complete all as specified and directed. |
| 50 | M&L butt hinges, medium weight 75 mm long size etc complete all as specified and directed. |
| 51 | S&F Aluminium anodised barrel tower bolt of extruded section and fixed 100 mm long etc complete all as specified and directed. |
| 52 | S&F Aluminium anodised barrel tower bolt of extruded section and fixed 200 mm long etc complete all as specified and directed. |
| 53 | S&F Aluminium handle cast type anodised 150 mm long etc complete all as specified and directed. |
| 54 | S&F 125mm size aluminium handles,cast type,anodised all as directed complete all as specified and directed. |
| 55 | S & F 3mm thick figured glass panes pinheaded and glazing with oil putty & pins/spring pins complete in squares n.exc 0.50 sqm each panes etc complete all as specified and directed. |
| 56 | S&F 3 mm Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane |
| 57 | Taking down cement plaster on brick walls including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 58 | Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excl ashalar facing etc complete all as specified and directed. |
| 59 | M&L GI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed and bird proofing in walls incl all laps cutting and waste complete all as specified and directed. |
| 60 | M&L 15mm thick plastering in CM (1:4) on one side of lathing in two separate layers even and smooth without using extra cement complete all as specified and directed. |
| 61 | M&L 12 mm thick plastering in CM (1:6) on the other side of lathing finished even and smooth without using extra cement complete all as specified and directed. |
| 62 | M & L rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete work even and smooth without using extra cement etc complete all as specified and directed. |
| 63 | M & L rendering 15mm thick in cement mortar 1:6 on fair faces of brick or concrete work even and smooth without using extra cement etc complete all as specified and directed. |
| 64 | M&L for applying two coats of oil bound distemper on new plastered surfaces of walls including preparation of surface over & including a coat of primer, on plastered surfaces, preparatory to distempering complete all as specified and directed. |
| 65 | M&L for prepration of new plastered surfaces ofwall and applying two coats of oil emulsion distemper over & incl a coat of primer on wall surfaces complete all as specified and directed. |
| 66 | M&L for complete removal of exisitng treatment of old decorated surfaces ofwall & applying two coats of oil emulsion distemper over & including a coat of primercomplete all as specified and directed. |
| 67 | M&L for preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applyingone coat of oil bound distemper of approved shade/tint etc complete all as specified and directed. |
| 68 | M&L for preparation of new plastered surfaces and applying two coats of exterior weather paint over & including a coat of primer onwall surface complete all as specified and directed. |
| 69 | M&L for complete removal of exisitng treatment of old decorated surfaces ofwall & applying two coats of exterior weather paint over & including a coat of primer onwall surface upto 3 storeyed bldg complete all as specified and directed. |
| 70 | M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over & including acoat of pink primer etc complete all as specified and directed. |
| 71 | M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying onecoat of synthetic enamel paint all as specified. |
| 72 | M&L for preparation of old steel surfaces exc 10cm width or girth and applying one coat of synthetic enamel paint all as specified & directed. |
| 73 | Taking upor down steel tubing and connections includingwith all fittings for 15 mm bore GI tubing etc complete all as specified and directed. |
| 74 | Taking upor down steel tubing and connections includingwith all fittings for 20 mm bore GI tubing etc complete all as specified and directed. |
| 75 | Refixing of old steel tubing and connections in new or old position with & including new all fittings laid infloor, wall or ceiling as directed, for 15mm bore GI tubing etc complete all as specified and directed. |
| 76 | Refixing of old steel tubing and connections in new or old position with all new fittings laid infloor, wall or ceiling as directed, for 20mm bore GI tubing etc complete all as specified and directed. |
| 77 | S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore etc complete all as specified and directed. |
| 78 | S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore etc complete all as specified and directed. |
| 79 | M&L dismantling water tank of exc 250 ltr and not exc 500 ltr Capacity etc complete all as specified and directed. |
| 80 | M&L dismantling water tank of exc 500 ltr and not exc 1000 ltr Capacity etc complete all as specified and directed. |
| 81 | S&F 1000 ltrs Rotational moulded polyethylene double layer water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl disconecting of existing tank all as specified in SSR Part I (Capacity in litres 1000) complete all as specified and directed. |
| 82 | S&F 500 ltrs Rotational moulded polyethylene double layer water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl disconecting of existing tank all as specified in SSR Part I (Capacity in litres 500) complete all as specified and directed. |
| 83 | S&F 20mm ball valves high pressure of PTMT with epooxy coated aluminium road & high density plastic ballscrewed for iron pipe or brass etc complete all as specified and directed. |
| 84 | S&F in repairs WHB Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15 mm bore dia of pipe etc. complete all as specified and directed. |
| 85 | S&F in repairs Health faucet of CP 15MM bore fancy type with suitable flexible pipe as per site reqmt incl CP nipple with socket etc complete all as specified and directed. |
| 86 | M&L for cutiting chases in brick wall, pinning in , making good to fancings where reqd and pointing in cement mortar (1:3) ends or edges of landings, steps etc all as specified & directed |
| 87 | S&F in repairs for 15mm dia of pipe Anglevalves,fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed etc complete all as specified and as directed. |
| 88 | S&F in repairs PVC connection 15mm dia and 45cm long with two Nosof brass checknuts and washers complete. |
| 89 | S&F in repair brass chromium plated fancy shower rose 125 mm in size with or without swivel joints any size incl fixing to steel pipe or union etc complete all as specified and directed. |
| 90 | S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plate bracket guard and railing 60 cm long etc complete all as specified and directed. |
| 91 | S&F in repair CP towel rail 600mm long aluminium anodised of brass CP fixed with and incl CP brass screws etc. complete all as specified and directed. |
| 92 | M&L for Granite (of any type) tiles 18-20mm as in platform thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigmentto match the shade of granite stone including grinding and polishing with nosing over 10 mm screed bed in CM (1:4) complete all as directed by Engr-in-Charge. |
| 93 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification etc complete all as specified and directed. |
| 94 | S&F Factory made solid panel pvc doorshutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined to-gether with solvent cement as per specification etc complete all as specified and directed. |
| 95 | Supply and fixed in repair vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed etc complete all as specified and directed. |
| 96 | S&F in repairs vitreous china water closet Padestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe and including EWC Seat cover complete all as directed. |
| 97 | S&F in repair PVC low level flushing cistern 10 ltr capacity syphonic action type white body with MS bracket,inlet ball valve, floathandle and flush pipe (for EWC or WC) etc complete all as specified and directed. |
| 98 | S& F in repairs Pillar taps, cast copper alloy,chromium plated, screwed down high pressure, with or without lettered ‘Hot\" or ‘Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as spfd & directed. |
| 99 | S&F in repairs for 15mm dia of pipe bib taps cast copper alloy, fancy type, chromium plated , screwed for iron pipe or for brass ferrule and fixed etc complete all as specified and directed. |
| 100 | S&F in repairs for 15mm dia of pipe stopvalves,fancy type and chromium plated screwed down high pressure ,screwed both ends for iron pipes or for Unions and fixed etc complete all as specified and directed. |
| 101 | S&F grating doom 125mm dia with waste hole of PTMT (Min wt 40 gms) etc complete all as specified and directed. |
| 102 | S& F in repairs PVC mounted 5mm thick bevelled edge looking mirror 600 x 450mm including taking down old fixed with chromium plated brass screws and cup washers etc complete all as specified and directed. |
| 103 | M&L cement concrete type C-2 (1:3:6) (using 40 mm graded stone agg) as in surface channels and drains etc complete all as specified and directed. |
| 104 | M&L for PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in coping including necessary formwork complete all as spfd and directed |
| 105 | S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 106 | S&F in repairsfor Draperly rod /Harrison rails of CP of 20mm dia with fixing brackets , stops, rollers and ringsetc complete all as specified and directed. |
| 107 | M&L second class hardwood plain fillets exc 13sqcm and notexc. 25sqcm, square or rectangular in section, wrought, secured with nails or brads etc complete all as specified and directed. |
| 108 | S&F PVC (SWR) 110mm dia single socketed in any length with rubber ring joints laid in trenches or in floor etc complete all as specified and directed. |
| 109 | S&F PVC (SWR) 110mm dia bends in any radius etc complete all as specified and directed. |
| 110 | S&F PVC (SWR) 110mm dia junction single T equal or un equal with an floor etc complete all as specified and directed. |
| 111 | M & Lfor 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 112 | S & F 75mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 113 | S & F 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal etc complete all as specified and directed. |
| 114 | M & L for RCC (1:1.5:3) type A1, Nominal Mix (using 20 mm graded granite stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed. |
| 115 | M & L for RCC (1:1.5:3) type A1, Nominal Mix (using 20 mm graded granite stone aggregate) as in columns, pillar, piers, posts & structures etc complete all as specified and directed. |
| 116 | M & L for RCC (1:1.5:3) type A1, Nominal Mix (using 20 mm graded granite stone aggregate) as in beams, cantilivers bressumers, limited over 1.5 m spam etc complete all as specified and directed. |
| 117 | Use and waste for formwork to sides of concrete foundation,footings,bases of columns,raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work;vertical or to batter etc complete all as specified and directed. |
| 118 | Use & waste of formwork for Formwork to sides of pillars, posts, struts, piers, columns and stanchions all as directed by Engr-in-Charge. |
| 119 | S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roofcovering /cladding to wall, fixed with self tapping screws etc complete all as specified and directed. |
| 120 | S & F Pre-painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed. |
| 121 | Supply only water proofing compound etc complete all as specified and as directed . |
| 122 | S&F for anodised aluminium powder coated any colour window and vantilator shutters, aluminium section weighting 0.55 kg/m including necessary joining, cleats,glazing clips,rubbber neoprene, packing, hinges anodised aluminium snap beading screw etc complete all as specified and directed. |
| 123 | M & L for Moorum/ Red bajri filling in floors or pavings, laid in layers n exc 15 cm thic spread, levelled and rammed incl wateringetc complete all as specified and directed. |
| 124 | M&L for hardcore (broken stone) of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammmed to a true surface etc complete all as specified & directed by Engr-in-Charge. |
| 125 | M&L for non skid coloured joint free tiles 7 to 8 mm thick area of each tile exceed 0.18 sqm but not exc 0.38 sqm ,in floor etc. set and jointd in neat cement slurry and pointed in white or coloured cement to match the shade of tiles , laid over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes CM (1:6) etc complete all as specified and directed. |
| 126 | All as per Ser item No 125.00 (here-in-before) but on vertical surfaces such as skirting, dado risers to steps over and incl 10mm thick bedding layer in CM (1:4) |
| 127 | M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick or concrete work even and smooth without using extra cement & using water proofing compound as per manufacturer instruction. etc complete all as specified and directed. (WPC will be measured and paid separately) |
| 128 | M&L for preparation of new plastered surfaces and applying two coats ofcement base paint over a coat of primerof approved shade on walls all as specified & directedby Engineer-in-Charge |
| 129 | M&L for preparation of old plastered surfaces and applying one coat ofcement base paint etcl as specified & directedby Engineer-in-Charge |
| 130 | M&Lfor 3 mmthick Birla white putty/JK white wall care putty on walls etc. complete all as specified and directed. |
| 131 | Supplying and laying 16 mm outer diameter CPVC pipe SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floorsetc. complete all as specified and directed. |
| 132 | Supplying and laying 20 mm outer diameter CPVC pipe SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floorsetc. complete all as specified and directed. |
| 133 | S&F brass Elbow 16mm outer diameter CPVC pipe etc. complete all as specified and directed. |
| 134 | S&F brass Elbow 20mm outer diameter CPVC pipe etc. complete all as specified and directed. |
| 135 | S & F in repairs Vitreous China Urinal,hafl stall urinal, white incl PTMT urinal spreader, waste pipe of polythene of low or high density of PVC 32MM diaetc complete all as specified and as directed. |
| 136 | S&Fcorner glass shelf assembly 300mm radius made of 6mm thick craaylic glass, with CP railing, fixed with suitable rowal plug & screws etc complete all as specified and directed. |
| 137 | S&F in repair soap dish chromium plated stell/stainless steel, approx size 160x160mm x 1mm thick, fixed to walls with plugs & CP brass screws etc complete all as specified and directed. |
| 138 | S&F in repairs CP wall mixer (3 in 1) etc complete all as specified and directed. |
| 139 | S&F for mild steel conforming to Fe 410-0 or Fe 310-0 in bands, straps, supports or stays for rain water, including bolts, if required, hook and pintle hinges; hand made sliding bolts; clamps; hold fasts; hooks for hanging fans and similar small articles etc complete all as specified and directed. |
| 140 | M&L cast iron work grade FG-150, unmachined, in brakets, gull,y traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop vulve boxes, gate stops, parts of ranges, bulusters and similar articles exc 5kg each etc complete all as specified and directed. |
| 141 | S&F 30mm thickfactory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete all as specified and directed. |
| 142 | S&F for depth 0.70mm-1.65 DWCPE (SN8) 180 (OD)/ 163 (ID) mm diameter pipes laid on 150mm thick PCC (1:3:6) type C-2 using 40mm graded stone agg incl packing under and hunching against the sides of pipes bed with and inclnecy excavation, returning filling and removal in any type of soil, RCC/Precast RCC with SFRC ventilating cover and frame, incl all items and activities ti execute and amek sewer line functinaletc complete all as specified and directed. |
| 143 | Dismantling asbestos cement (Corrugated or semi corrugated) sheets in roof covering etc complete all as specified and directed. |
| 144 | Demolition of plain cement concrete of any description in any position not otherwise specifically provided for etc complete all as specified and directed. |
| 145 | S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 146 | S&F for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section of size 40 x 18 x 1.29mm thick including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed. |
| 147 | S&Ffor galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and directed. |
| 148 | S&F for 300mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts fixed etc complete all as specified and as directed. |
| 149 | S&F in repair 300 mm MS ordinary rat tail spring including roller and roller plate complete all as specified and directed. |
| 150 | S&F in repairs vitreous china squatting pan \"orissa\" pattern size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe)complete all as specified and directed. |
| 151 | S&F of 75mm dia PVC (SWR) Vent cowl etc complete all as specified and directed. |
| 152 | S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 153 | S&F in repairs for 75mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof etc complete all as specified and directed. |
| 154 | M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement incl firms mouldsetc complete all as specified and directed. |
| 155 | M&L for precast factory made manhole cover/drain covers with plain faces using RCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) and set in CM (1:4) including necessary formwork etc of required sizes etc complete all as specified and directed. |
| 156 | Taking down carefullycopper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling,floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed. |
| 157 | M&L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable1100 volts grade with multi-stranded copper conductors, drawn throughand including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site complete all as specified and as directed. |
| 158 | Onelight/Fan point controlled by one, one way switch . |
| 159 | One 3 pin socket outlet 5 Amps on the same board with other switches. |
| 160 | One 3 pin socket outlet 5 Amps on the switch socket combination. |
| 161 | All as per Ser item No 157.00 (here-in-before) but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed. |
| 162 | M&L for Switch piano flush type single pole, one way 5Aetc complete all as specified and directed. |
| 163 | M&L for Socket outlet, 2 in 1, 5 pin 5A flush type etc complete all as specified and directed. |
| 164 | M&L for Switch Socket combination, 2 in 1, 5 pin 6A flush type etc complete all as specified and directed. |
| 165 | M&L for Switch Socket combination, 2 in 1, 5 pin 6A/16A flush type etc complete all as specified and directed. |
| 166 | M&L for stepped type electronic fan regulator 100 Watt socket size flush type on the existing phenolic laminated sheet etc complete all as specified and directed. |
| 167 | M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock complete all as specified and directed. |
| 168 | Material and labour for (concelaed Type) point wiring including necessary chases cutting of wall for one light/fan/call bell point with 1.5 sqmmPVC insulated (FR-LSH) PVC sheathed multistranded copper conductor cable 1100 volts gradecontrolled by one way switchincluding 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit with all accessoriesfor mounting of fittings like switch, socket and fan regulator with modular inner plate and cover plate and making good the distrubed surfaces as per the existing complete all as specified and as directed by the Engr-in-Charge. ake: finolex/Richa/RR Kabel. Make of caping/casing & PVC boxes: Prestoplast/finolex/Supreme/Richa |
| 169 | Onelight/fan pointcontrolled by one, one way switch. |
| 170 | One 3 pin socket outlet 5 Amps on the same board with other switches |
| 171 | One 3 pin socket outlet 5 Amps on the independent board. |
| 172 | All as per item No.165.00 (here-in-before) but with 2.5 Sqmm for 3 pin 15 Amps switch socket point on independent board along with one run of 2.5 Sqmm copper conductor green in colour as earth continuity conductor connected to earth dolly complete all as specified and as directed. |
| 173 | M&L for Modular Switch 1 way 6A,1 module etc complete all as specified and directed. |
| 174 | M&L for modular switch 1 way 16A, 1 module etc complete all as specified and directed. |
| 175 | M&L for Modular Socket ,6A/2/3 pin combined 2 module etc complete all as specified and directed. |
| 176 | M&L Modular Socket ,6A/16A-2/3 pin combined 2 module etc complete all as specified and directed. |
| 177 | M&L for stepped type electronic fan regulator,120 W-2 module etc complete all as specified and directed. |
| 178 | M&L for Metal flush box 1/2 module etc complete all as specified and directed. |
| 179 | M&L for Metal flush box 3 module etc complete all as specified and directed. |
| 180 | M&L for Metal flush box 4 module etc complete all as specified and directed. |
| 181 | M&L for Metal flush box 6 module etc complete all as specified and directed. |
| 182 | M&L for Metal flush box 18 module etc complete all as specified and directed. |
| 183 | M&L for modular white cover plate with frame 2 module complete all as specified and as directed. |
| 184 | M&L for modular white cover plate with frame 3 module complete all as specified and as directed. |
| 185 | M&L for modular white cover plate with frame 4 module complete all as specified and as directed. |
| 186 | M&L for modular white cover plate with frame 6 module complete all as specified and as directed. |
| 187 | M&L for modular white cover plate with frame 18 module complete all as specified and as directed. |
| 188 | M&L for Modular bell push switch 5 amps piano type flush type etc complete all as specified and directed. |
| 189 | M&L for replacement of Bell AC 230 volts musical type etc complete all as specified and directed. |
| 190 | Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of4 Sq mm and one run of 4 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn throughand including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- two runs of 4 Sq mm + one run of 4 Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length .Make:- Finolex/Havells/RR KabelMake of caping/casing :- Prestoplast/Finolex/supreme |
| 191 | M&L for sub main wiringtwo run 4.0 Sq mm andone run of 4.0 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn throughand including PVC conduit pipecomplete all as specified and as directed. NOTE:- two runs of 4.0 Sq mm +one run of 4.0 Sq mm and two run of PVC conduit pipe and its accessories of suitable size shall be measured as one unit length |
| 192 | Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 193 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling and connecting up with driver, three core flexible copper conductor of suitable size complete all as specified and as directed. |
| 194 | Supply and fixing LED luminaire 600 mm x 600 mm, 40/42 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. |
| 195 | Taking down S&F for , LED Light fitting 1 x 20 watt (4 Ft), basic all purpose surface and wall mounted LED battern with polycarbonate housing & intergrated electric driver with all accessoriesincl connecting up with and incl twin/ three core twisted flexible copper conductor cable of suitable size in and incl flexible hose from ceiling rose to fitting complete all as specified and as directed. Make : Crompton Geaves Cat No -CCS-102-20-65-SL-DP-NWH/ Bajaj/ Philips. |
| 196 | All as per item No- 189.00 (here-in-before) but LED Tube light 10 Watt (2 ft) complete all as specified and as directed. |
| 197 | Taking down Supply , fixing and testing in replacement of LED Bldg Security light fitting of capacity 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.2 mtr GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling of holes as reqd and connecting up with flexible copper cable of size 0.75 sqmm 3 core from ceiling rose to the light fitting and all as specified and directed by Engr-in-Charge..Make : CG, Cat No- LSTS-20-CDL-M/ Bajaj/ Philips |
| 198 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and as directed.Make : Bajaj/CG/V-Guard |
| 199 | M&L for motor starter S.P .32A completeincl taking downold UNSVall as specified and as directed. Make: Havells/HPL/Legrand |
| 200 | M&L for MCB Distribution board double door type SPN 12 way, sheet steel, powder coated, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity completeincl taking down old UNSVall as specified and as directed.Note :MCB SPN/SP will be measured and paid separately.Make:- Legrand Cat No 507611 or equivalent in ABB/Siemens |
| 201 | M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, withneutral link & earth bar etc. and fixing MCBs of various rating capacity MCB DBs complete all as specified and as directed.Make : Legrand Cat Part No 507611/ABB/Siemens |
| 202 | M&L for MCB Distribution board double door type SPN 4 way, sheet steel, powder painted, withneutral link & earth bar etc. and fixing MCBs of various rating capacity MCB DBs complete all as specified and as directed.Make : Legrand Cat Part No 507611/ABB/Siemens |
| 203 | Supply and fixing MCB SPN 40 to 63 Amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DBincl taking down old unsv MCB complete all as specified and as directed |
| 204 | Supply and fixing MCB SPN 32 Amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DBincl taking down old unsv MCB complete all as specified and as directed |
| 205 | Supply and fixing MCB SP 6 to 32 Amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DBincl taking down old unsv MCB complete all as specified and as directed |
| 206 | Taking down Ceiling fan/ Exhaust Fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades,hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed. |
| 207 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed. |
| 208 | Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint |
| 209 | Taking down LT UG cable/ service connection of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 16 sq mm, 2 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. |
| 210 | All as per item No 203.00 (here-in-before) but 10 Sqmm 2 Core complete all as specified and as directed. |
| 211 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified ans as directed. |
| 212 | Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified ans as directed. |
| 213 | Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified ans as directed. |
| 214 | M&L for spread fine river sand in trenches complete all as specified ans as directed. NOTE: For measurement purpose, punned down thickness shall only be taken. |
| 215 | M&L for laying brick sub class \"B\" old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed |
| 216 | Supply & laying tubes \"light grade\" galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 32 mm dia bore including taking out unsv GI tubing complete all as specified and as directed. |
| 217 | M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i)The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI cover 10 m thick, funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSRPart-II. (ii)Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type mounted on insulators, where ever applicable. |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
