Tender For special Repair To Bldg No P-112, P-113 And P-245 At Mil Stn Sgnr- 1 Dismatiling brick tiles or terracing tiles, single layer on roofs and mud phuska complete all as specified and directed. 2 M&L for laying roof PCC tiles 20cmx20cmx25mmthick with grey cement and no pigment , set , jointed and pointed in neat cement slurry in roof floors laid over 15mm thick CM 1:6 complete all as specified and directed. 3 M&L for PCC (1:2:4) Bo using 12.5 mm graded stone aggregate as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc., with approved water proofing compound all as per manufacturers instructuions on the roof surface to achieve requisite slope all as specified and directed. (Note :- Supply only water proofing compound shallbe measured & paid separately). 4 Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 8-10 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed. 5 M&L for PCC 1:2:4 , type B-0 (using 12.50 mm stone aggregate) as in benching (gola ) making concave shape gola of 80mm radius at juctions of roof/terrace with parapets/sides walls complete all as specified and directed. 6 M&L for Roof treatment to RCC roofas follows :- (a) Cleaning the roof surfaces thoroughly using wire brushes to remove sharp projections,cleaning joints, washing, drying and removing all dirt/dust to receive concrete padding/ plaster etc complete. (b) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:4)with WPC , finished even and smooth without using extra cement.(c) Providing one coat of approved bituminous primer @ 100 gms per sqm, over dried plastered surface. (d) Laying 3 mm thick APP based polymeric membrane, (mineral finish) minimum weighing 3 Kg/Sqm reinforced withnon woven polyster fabric (weight not less than 150 gms/Sqm) by torch application. The overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by Engineer-in-Charge.Makes:-STP, Dr Fixit, SIKKA, Torch Tar Notes: (i) All joints and change in directions should be covered with cement mortar (1:3) mixed with SBR latex @ 200 ml/bag of cement/ as per site requirement and cured well before laying membrane by torching.(ii) All angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) Water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only.The name of firm and applicator shall be got approved from GE before carrying out the work. (iv) The independent testing of membrane for technical parameters given in particular specificationsshall be carried out from Govt approved labs having fascilities for testing of membrane. (v) The guarantee of treatment shall be for minimum 10 yearsreckoned from date of completion of whole work. 7 Dismantling floor hearth or wall tiling including cement mortor bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 8 M&L non skid premium 1st quality ceramic coloured tiles8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured polymer based grout to match over and including 20 mm thick screed bed in cm 1:4 complete all as specified and directed. 9 M&L 595/x595x8mm / 600x300x8mm mm thick double charged, stain free, vitrified colour tiles as in vertical sufaces such as skirting or dado set & jointed in neat cement slurry & pointed in epoxy groute to match the shade of tiles including 10mm backing coat in CM 1:4 complete all as specified and directed. 10 M&L for stain free Vitrified Ceramic colour tiles 8 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured epoxy groute to match including 20mm thick screed in CM 1:4 complete all as specified and directed. 11 M & Lmachine cut kota stone slab flooring 20-25mm thick(minimum size 55 cms x 55 cms) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing including 15mm of screed bed in CM 1:6 aggregate complete all as specified and directed. 12 M & L machine cut kota stone slabs as in vertical surfces such as risers of steps/vertical surfaces 18-20mm thickover cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing also moulding edgesincluding 10mm of backing coat in CM 1:4, complete all as specified and directed. 13 M & L granite (of any type)work 20 mm thick(table rubbedand polished) in hand wash platforms and like in cement mortar 1:4including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm of screed bed in CM 1:6 complete all as specified and directed. 14 Demolition of brick work built in cement mortar of any description complete all as specified and directed. 15 M&L for brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. 16 Taking down cement plaster including raking out joint, hacking for key & scrubbing down with water etc complete all as specified and directed. 17 M&L, 15mm thick rendering in CM 1:6 on fair faces of brick or concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed. 18 M&L, 15mm thick rendering/plastering 15 mm thick on any face of brick wall or concrete surface consisting in two layers i.e. First laye 10 mm thick in cement mortar (1:4) and second (top layer) layer 5 mm thick in cment mortar (1:4) including mixing of liquid WPC in mortar @ asper manufacturer instruciton per bag of cement of 50 Kg, finisied fair and even without using extra cement complete all as specified and as directed.(Note: WPC shall be measured & paid separately as supply only) 19 M&L, 5mm thick rendering in CM 1:3 on fair faces of concrete surfaces as on ceilings finished even and smooth without using extra cement complete all as specified and directed. 20 M&L three coats of white wash to new surfaces on ceilings including preparation of surface complete all as specified and directed. 21 M&L two coats of cement based paint over 1.0 mm thick wall putty over a coat of primer on newly plastered surface includingpreparation of surface complete all as specified and directed. (Note : The prepared surface after wall putty will be passed by the GE, through written order before applying future extra finishes) 22 M&L two coats of Interior Acrylic Emulsion over 1.00 mm thick wall puty over a coat of primer on newly plastered surface includingpreparation of surface complete.(Note : The prepared surface after wall putty will be passed by the GE, through written order before applying future extra finishes) 23 M&L two coats of white wash to old surfaces on ceilings including preparation of surface complete all as specified and directed. 24 M&L forComplete removal of existing treatment and applyingtwocoats of Interior Acrylic Emulsionto oldsurfaces of wall over over 1.00 mm thick wall putty includingpreparation of surface complete all as specified and directed. 25 S&F Steel window with side hung shuttrs including projection type hinges with steel handlde, and steel peg stya complete all as specified and directed. 26 Taking down unserviceable MS steel Gate/Door of any description, type and size by straightening stiles/ rails and welding hinges/hold fasts and joints includingand refixing after making serviceable/ functional complete in all respects all as directed complete all as specified. complete all as specified and directed .Note : Rates are included in reinforcement/emp of JCB or Crane and operator to dismantle/taking down the MS Gate/Door, welding works etc. 27 Taking down steel window/ventilators chowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqm each complete all as specified and directed. 28 S&F 10mm dia MS round guard bars for steel windows/Stair case railing complete all as specified and directed. 29 S&F MS falt iron 25 x 6mm as in hold fast confirming to Fe 290 Gde E-165 complete all as specified and directed. 30 Cutting holes in brick (n.exc half brick)walls in cement mortar forinserting holdfasts andmaking gooddismantled portion incement mortar 1:3 or cement concrete 1:2:4Type B-1 complete all as specified and directed. 31 S&F framed brackets of angles or tee with web and flange cut to shape, drilled and counter shunk for screw, including bending and welding angles asnecessary gusset plates riveting rails, braces,running rails and guides and hanging, peg stay for steel windows/ventilators ; also fastening and fixing complete conforming to Fe-290(Grade-165)complete all as specified and directed. 32 S& F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 33 S&F powder coated aluminium door shutters/paritition with sliding arrangements etc, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,powder coated aluminum snap beading screws etc. includingaluminium 4 lever Mortice lock , vertical type, size 100 mm and directed double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed. 34 S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars,aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws and sliding aluminium channel, wheels and locking arragements , anodised aluminium fittings such as peg stays 150mm long, hinges type B-21 100mm long, suitable handle and tower bolt and including anodised aluminum grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15 ) of approved design /pattern, with approved standard section and fixed to the window /doorwith C.P brass/SS screw @ 200mm centre to centre , including cutting the grill to proper opening size for fixing and operation of handles including flyproof wire mesh. as per requirement complete all as specified and directed. 35 S&F Anodised aluminum grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15 ) of approved design /pattern, with approved standard section and fixed to the window /doorwith C.P brass/SS screw @ 200mm centre to centre , including cutting the grill to proper opening size for fixing and operation of handles including flyproof wire mesh. Note:- Design shall be approvedby Engineer - in - Charge. Note :- Minimum thickness of powder coating shall not be less than 50 micron. 36 S & F for 5.5mm thick sheet glass(tinted),selected quality and glazing with necessory arrangement in square exc 0.5 sq. m in each pane complete all as specified and directed. 37 S&F in repair for door closer hydraulically regulated, alunimiunbody designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed. 38 Taking down wooden chowkats or frames (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified and directed. 39 Taking down wooden/FRP/PVCchowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqmeach complete all as specified and directed. 40 Taking down shutters door/window/cupboard of any description (wooden/aluminium/Iron/Glass) of any material and any typeexc 1 Sqm but n exc 2 sqm each and repairing work in all respects (including neccessary cleats, rubber packing etc in almuminium Door, lung/hold fasts) and refixing in same opening complete all as specified and directed. 41 Taking down shutters of any material and description and type n exc 1 Sqmeach and refixing in same opening after resecuring easing duly completed repair work in all respects etc.ccomplete all as specified and directed. 42 S & F 1.25mm thick sheet pressed steel frames of frame size 125 x 60mmfor doors with one or more rebatesincluding necessary fixing lugs, lock strike plate, etc., complete, as specified,supplied and fixed complete all as specified and directed. 43 S & F 1.25mm thick sheet pressed steel frames of frame size 105 x 60mmfor doors with one or more rebatesincluding necessary fixing lugs, lock strike plate, etc., complete, as specified,supplied and fixed complete all as specified and directed. 44 M&L for providing cement concrete (1:3:6) type C1 using 20 mm gradded stone aggregate for filling in pressed steel frames and PCC blocks for hold fasts complete all as specified and directed. 45 S & F 2nd class hardwood 35mm thick shutter, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers including fittings per shutter i.e.125 mm SS hinges (03 Nos),200 mm longAluminium tower bolt (02 Nos) and 300mm long Aluminium sliding bolt (01/02 Nos) & Aluminium handles (02 Nos) each: supplied and fitted to chowkats complete all as specified and directed. 46 S&F in repair PVC connection 15mm size with PTMT nuts of length 650 mm long complete all as specified and directed. 47 S&F door viewer vide angle brass with glass cap 14 mm dia complete all as specified and directed. 48 M&L 2nd class hardwood 35mm thick Glazed and skeleton shutters of door/window/ ventilaor, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. 49 Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of but of Frame size 65x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed.(M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 50 Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calciumcarbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: 125 mm long stainless steel butt hinges (03 nos), 150 mm long aluminium handles (02 Nos) and 150 mm longaluminium tower bolts shall not be paid separately) 51 S&Faluminium handle cast type anodised, 150mm longcomplete all as specified and directed. 52 S&F 150 alminium anodies barrel tower bolts of extruded sction and fixed complete all as specified and directed. 53 S&F 300mm long aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed. 54 S&F 125 mmbutt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type C-21 complete all as specified and directed. 55 S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. 56 S & F for floor door stopper of aluminium alloy body and tongue, Overall length of cover plate 140mm anodised, with hard drawn steel spring, complete all as specified and directed. 57 M&L for preparation of old surface including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and removing all dirt and dust by watering making surface even and smooth and then applying two coats of cement base paint over over1 mm thick wall putty well prepared old decorated plastered surface etc all as specified and directed. 58 M & L for preparation of old decorated wall surfacesby brooming down or steel wire brushing,scrapping down smoke soot,moulds,moss and efflorescent salts and trading oil and greasy spotsand then applying two coat of Interior Acrylic Emulsion over1.00 mm thick wall puttycomplete all as specified and directed. 59 M&L two coats of synthetic enamel paint over a coat of pink primer on new surfaces of wooden and wood based materials over 10 cm width or girth including preparation of surfaces complete all as specified and directed. 60 M&L one coat of synthetic enamel paint on old painted surfaces of wood and wood based materials over 10 cm width or girth including preparation complete all as specified and directed. 61 M&L one coat of synthetic enamel paint on old painted surfaces of steel and iron work over 10 cm width or girth including preparation complete all as specified and directed. 62 M&L two coats of synthetic enamel paint over a coat of red oxide primer on new surfaces of steeland steel based materials over 10 cm width or girth including preparation of surfaces complete all as specified and directed. 63 S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed. 64 S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 65 S&Fventilationn window blinds withclosing and opening arrengement complete all as specified and directed. 66 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick sorrounds, glazed with oil putty or fixed with beads complete all as specified and directed. 67 S&F 4mm sheet glass ordinary quality and glazing with oil putty in squaren. exc 0.5 sqm in each plane complete all as specified and directed. 68 Supply & Fix 4mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in suqares exc 0.5 Sqm in each pane complete all as specified and directed. 69 Supply and fixing curtain rod 25mm dia MS pipe with coloured PVC coated, wall thickness of pipe not less than 20 guage, including fancy type brackets and pair of decorated end knobs (finials), stop roller etc. as per site requirement, fixed to wall with fixing accessories, including taking down old existing curtain rods any description complete all as specified and directed. 70 Taking down eaves gutter or rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks etc. complete all as specified and directed. 71 S&F 110mm bore PVC (SWR) rain water pipe single socketed in any length with rubber ring joints, jointed with solvent fixed to wall with matching PVC SWR rings including cutting holes and making good the disturbed portion with PCC (1:2:4) type B0 including clamps and bends complete all as specified and directed. 72 Taking up or down GI steel water tubing 15mm bore and connections including fittings from floor/walls/ceiling complete all as specified and directed. 73 Taking up or down GI Steel water tubing 20mm bore and connections including fittings from floor/walls/centrings complete all as specified and directed. 74 S & F Galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good complete all as specified and directed. 75 S & F GI steel water tubing 20mm bore medium grade with all fittings and fixed complete to walls ceiling or laid in floors complete all as specified and directed. 76 Dismantling water tanks any type exc. 500 ltr but nexc 1000 ltrcomplete all as specified and directed. 77 S & F rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part -I (1000 Ltrs) capacity complete all as specified and directed. (Note PVC tank shall be ISI marked & having two layer) 78 S&F 20mm ball valves high pressure of PTMT with epoxy coatedAluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 mm - 210 gms / 25mm-455gms/ 40mm - 690 gms). complete all as specified and directed. 79 S&F wall hung WC with UF Seat Cover ,Hinges, Accessories SetSize 640 x 360 x 765 mm white complete, includingconcealed body flushing cisternwith hinging arrangement, complete all as specified and directed. 80 S&F health faucet to EWC, CP brass with minimum 1000mm long CP flexible pipe, connection etc., complete all as complete all as specified and directed. 81 S&F in repair for vitreous China urinals,full stall urinal (back or corner wall type), complete includingproviding and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) and including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed. 82 S&F Urinal partitions slabs terminating about 40cm above floor line, fixed in repairs complete all as specified and directed. 83 Supply and fix in replacement vitreous china wash hand basin white flat back of size 550mm X 400mm (table top/corner or any type), fixed with a set of cast iron brackets including cutting and pinning in ends of brackets to wall, including 15mm size CP pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or cold with long scrwed shanks and fly nuts, 32mm dia brass chromium plated waste fittings 450mm long PVC connection of 15mm size with PTMT nuts and 40mm dia waste pipe complete all as specified and directed. 84 S&Fsoap dish CP brass 100mm dia (round or oval) fixed to walls or dados.complete all as specified and directed. 85 S&F in repairs brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified and directed. 86 S&F in repair CP Tubular towel rail, 20mm dia, D type, 600mm long between flanges fixed with CP brass screws complete all as specified and directed. 87 S&Fchromiumplated tubular towel rail 600mm long with lower hanger complete all as specified and directed. 88 S&F Towel Ring of aluminium fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms)complete all as specified and directed. 89 S&F in repairs cabinet of PTMT with looking mirrorof size 350x555mm complete all as specified and directed. 90 S&F frameless rectangular LED Mirror with touch switch600mm x800 mm5 mm thick glass mirror with double coat for protection and longevity grounded edges for safety and silver plating on the back for better reflection. mounted on wall with necessory fiments complete all as specified and directed. 91 Supply and fixing corner glass shelf assembly fancy type, made of 5mm thick sheet toughened glass of size 250x250mm, fixed along wall with chromium plated catcher brackets, brass screws and PVC plug complete all as specified and directed. 92 S&F 15mm bore PVC connections, with PTMT nuts, of length 450/600mm complete all as specified and directed. 93 S&F Single lever Basin Mixer without Popup waste with 450 long Braided Hoseswith long screwed for iron pipe of 15 mm dia, complete all as specified and directed. 94 S&FCentral Hole Basin Mixer without Popup waste System with 450 mm long Braided Housewith long screwed for iron pipe of 15 mm dia complete all as specified and directed. 95 Supply and fix in repairs chromium plated angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed. 96 Supply and fix in repairs chromium plated stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed. 97 S&F in repair concealed chromium plated Angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed. 98 S&F in repair 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 99 S&F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 100 S&Fin repairs 15mm bib taps cast copper alloy, chromium platedfancy type with crutch or butterfly handle screwed down screwed for Iron pipe or for brass ferrule and fixed complete all as specified and directed. 101 S&F Grating doom 100mm dia of CP (Minimum weight 25gms) complete all as specified and directed. 102 Dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches complete all as specified and directed. 103 S&F 75mm dia cast iron soil waste pipe and vent pipes in any lenth with or without ears with cement joint laid in trenches or in floors complete all as specified and directed. 104 S&F 75mm dia cast iron soil waste pipe and vent pipes in any length with or without ears with cement joint fixed to walls complete all as specified and directed. 105 S&F 75 mm bore dia CIbends/Tee(any radius) diminishing pieces or tapers complete all as specified and directed. 106 S&F 75 mm bore dia CIbends(any radius) with ducks foot or heel rest complete all as specified and directed. 107 S&F 75mm C I branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) complete all as specified and directed. 108 S&F75mm CI branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) complete all as specified and directed. 109 S&F, 100 mm dia cast iron soil waste pipe and vent pipes in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed. 110 S&F, 100 mm dia cast iron soil waste pipe and vent pipes in any lenth with or without ears with cement joints fixed to wall complete all as specified and directed. 111 S&F 100 mm bore dia CIbends/Tee(any radius) diminishing pieces or tapers complete all as specified and directed. 112 S&F 100mm CI bends (any radius) with ducks foot or heel rest complete all as specified and directed. 113 S&F100mm CI branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) complete all as specified and directed. 114 S&F100mm CI branch pieces, doube (equal or unequal) ordinary or inverted (spigot or socket type) complete all as specified and directed. 115 S&F 100 mm Traps P and S complete all as specified and directed. 116 S&F 75 mm Traps P and S complete all as specified and directed. 117 M & L for 75mm thick cement concrete type C-2, 1:3:6 using 40mm graged aggregate as in plinth protection complete all as specified and directed. 118 M & L for 40mm thick cement concrete type B-1, 1:2:4 using 20mm graged aggregate as in flooring , finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. 119 Demolition of cement concrete(unreinforeced) of any description and in any position for sunken portion (below or above ground level) complete all as specified and directed. 120 M&L for Water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below complete all as specified and directed by Engineer-in-Charge:- (a) applying 15 mm plaster in CM 1:3 with WPC on raised verticle surface (b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc. (c)Creating fillet coving of 50x50 mm with polymer modified mortar on the junction of slab and walls (d)Apply first coat of two component modified polymer coating on the horizontal and verticle surface(e)Provision of glass fiber mesh of 2 x 2 mm immediately on above coating (f) Apply second coat of two component modified polymer coating after 72 hrs (g) Cement concrete 1:4:8 over the coating as per requirment (h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout complete all as specified and directed by Engineer-in-Charge. Make:- Dr. Fixit/Fosroc/STP Note: (i)PCC filling in sunken portion will be measured seperately. Note : Complete treatment/work to be executed by the approved applicator.Warranty to be given by the applicator firm of 5 years in writing. 121 M&L for PCC (1:5:10) type E-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete or filling in sunken floor complete all as specified and directed. 122 Dismantling timber scantlings 40 sq. cm and over in section, in any position in framed work complete all as specified and directed. 123 M&L for Second class Clean sawn hard-woodPlain , solid , straight chowkhats and frames , wrought , framed rebated on the solid , rounded or chamfered , put together with glue, pinned at joints, supplied and fixed.inscantlings and for frame etc complete all as specified and directed. 124 S&F Continuous( piano) hinges , mild steel , bright finish or electrogalvanised Width of flaps 30mm (when open) complete all as specified and directed. 125 M &L for providingModular Cup boardwith shutters in required sizes& shape at site made out of 18 mm thick one side decorative laminate and other side balancing lamination sheet consisting of carcass 18 mm thick PVC sheet & PVC sheetwith all required brackets SS screws e.t.c. with adequate complete locking arragnements. The panels shall be fabricated using adhesive and screws where ever required . All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish as per manufacturer instructions and complete all as specified and directed. 126 S & F Stainless steel fancy type 200 mm handle complete all as specified and directed. 127 S& F Auto Closing Concealed Hinges for Half Overlay Doors with 95 Degree Opening Angle complete all as specified and directed. 128 M&L for Providing RCC precast cement concrete Type B0 1:2:4 (12.5mm gragded aggregate) 40 mm thick Jallies(measured solid includingallmouldings and frame) complete all as specified and directed. 129 S&F 0.56 mm thickPlain, Aluminium sheeting, Alloy 31000 H4 for crumple/ expansion joints, ridges, hips, valley gutter, drip,and straight flashing (length and girth as fixed)fixed with self tapping screws complete all as specified and directed. 130 Demolition of Cement concrete(reinforeced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 131 M&L Reinforced Cement concrete Type B1 1:2:4 (nominal mix) 20mm graded stone aggregate in slabs supported on walls, beams and columns , in floors, roofs, landings, balconies, canopies, deck slabs, chajja, parapit wall, slab, VIFT Wall/Traverse Wall and in shelves ann the like in cluding form work complete all as specified and directed. 132 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. 133 M&L providingreinfoced cement concrete (nominal mix) in cement concrete 1:1.5:3 Type A1(20mm graded aggregate)as chajjas, lintels, water tank staging slab and likeetcand similar workcomplete all as specified and directed.(Note : The rate quoted shall be deemed to include use and waste of necessary form work) 134 M & L Mild steel TMT bars5mm dia and over upto and including 10mm dia in stirrups, spacers and binders , cut to length, bent to shape required, including cranking, bendingspirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.(Note : Additional Reinforcement:In the case of the shear reinforcement also, if the diameter of the rebars are reduced, provide 8mm dia stirrups in the form of 2 U shaped bars. Tie them properly so that it has a tight contact with the main bars. ) 135 M & L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bendingspirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.(Note : Additional Reinforcement: Check th diameter of the existing rebars and if the diameter is less tahn 30% of the origianl diameter, provide additional reinforcement. Cut 12mm dia bars as main reinforcement to the required lengthwith proper development length. Tie them to the prefixed shear connectors so that the additional rebar acts monolithically with the existing ones and core concrete. 136 M&L for TMT bars 6 to 8mm dia and over cut to length bend to shape reqd incl crancking and incl mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. 137 S&F hollow section PVC wall Lining consisting of 5mm thick plain colour PVC sheetinclusive of solvent cement and fixing at site on PVC strips/fillets as per specification and drawing complete all as specified and directed. 138 Demolition concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) all as specified complete all as specified and directed. 139 M&L75 mm thick cement concrete type D2, 1:4:8 (Using 40mm graded stone aggregate)filling and mass concrete complete all as specified and directed. 140 M&L 25mm thick cement concrete flooring type B 1, 1:2:4 using 20 mm graded aggregate finished even and fair complete all as specified and directed. 141 M&L for sand filling (25mm thick) under floors or in foundations including watering and consolidation complete all as specified and directed. 142 M&L Machine pressed precast concrete interlocking paverblock any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified and directed. 143 M&L providing precast cement concrete in PCC (1:2:4) type B-1 with 20 mm graded aggregate for kerb stone and similar works with plain fair finishes including chamfers, weatherings, throat- ing etc. and setting in mortar (1:4) complete with joints to match complete all as specified and directed. 144 S & F for steel work in tubular trusses ,channels ,purlines, crange gantries, rails including special shaped washer, platesnuts and bolts, gusset plates, cleats,including necessary drillingetc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 including dismantling of framed trusses complete all as specified and directed. 145 S & F for Flat ironfor wind ties,plates (plain or chequered) channels, posts, square cut or notched (ordinary and counter sunk) forming holesetcFe 410 -W (Gde- E- 250) quality- A complete all as specified and directed. 146 S&F mild steel screw bolts (machine made) with hexagonal or square head at one end, and screwed the other,or screwed bothend to be fitted with washer and one hexagonal/ square nut not exceeding 5cm long and dia of neck 11 to 15mm complete all as specified and directed. 147 M & L for Chipping of slab/ columns/ beams/ chajjas/ parapet/ roof projection/balcony/staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris for all lead and lifts, all complete all as specified and directed. 148 M & L for Cleaning & applying rust remover in two coats over rusted reinforcement surface and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 6-8 sq. mtr/ltr not less than 50 microns dft with Sika friazinc R or equivalent to reinforcement surface as per manufacturer’s instructions including all scaffolding , machinery, tools tackles and clearing of debris. complete all as specified and directed. 149 M & L for Hard drawn steel wire fabric n exc 4Kg/Sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement complete all as specified and directed. 150 S & Fof new steel or rebars by drilling holes with 10 mm to 20mm dia and 100 to 200mm deep as per IS code of 10D formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends/shear connector and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding / fixing / placing in position the steel mesh reinforcement at desired level/ stretching complete all as specified and directed. (Note : Steel/reinforcement shall be paid and measured separately). 151 M & L for applying bond coat on the prepared old surface of concrete/masonry to receive new polymer mortar/polymer modified mortar or micro concre with two coats of Sika-Latex Super SBR or equivalent as per manufacturer specifications. Laying of reinstatement polymer mortar or micro concrete shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete complete all as specified and directed. 152 “M&L for applying to the damaged concrete portion of slab/ columns/ beams/ chajjas/ parapet / roof projection/ balcony/ staircase with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious patch repair mortar Sika monotop 122F or equivalent (having the technical parameters mentioned in material specifications) capable of applying up to 20-25mm thick in double layer initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness complete all as specified and directed. 153 M&L for 22 mm thick Plastic dividing strips, 1.5mm thickinserted in position, conform to design omplete all as specified and directed. 154 Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed 155 Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed 156 M&L 30 cm x 30 cm x 20-25 mm thick chequered cement concrete tiles set jointed and pointed in neat cement slurry in floors with grey cement and no pigmentswith 20mm of screed bed in CM 1:4 including coping at edges in PCC Type B1 (1:2:4) complete all as specified and directed 157 Dismantling steel/aluminium sheets of any type(corrugated semicorrugated ,Plain or corrugated steel sheeting,any gauge, thickness etc) sheet in roof covering complete all as specified and directed 158 S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed 159 S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed 160 Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed. 161 M & Lfor concealed conduit point wiring complete for light/ fan on independent /combine boardwith cable 1.5 sqmm (Nominal area) FRLSHPVC insulated multistranded unsheathed copper conductor,drawn in and includingPVC Concealed conduitpipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , aftercutting in wall chasing for conduits and sinkings for modular metal flush boxes suitable lengthandthickness for mounting, switches, sockets,fan regulatorwith modular cover plate with frame and making the gooddisturbed surfaces of wallin CM 1:3 with white wash or existing colour including provision ofcontinuousearth continuity conductoralong with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switchand connected to commonearth dolly, complete all as specified anddireced. 162 All as per Srl item No 161 here in before but for one switch socket combination5/6 amp on independent board complete all as specified and directed. 163 All as per Srl item No 161 here in before but for one three pin socket outlet 5 Amps on same board with other switchescomplete all as specified and directed. 164 All as per Srl item No 162 here in before but for one switch socket combination 6 pin 5/15 Amps on independed board with copper conductor 2.5 sqmmalongwith 2.5 sqmmearth contunity conductor complete all as specified and directed. 165 All as per Srl item No 161 here in before but for one light point controlled by two 2 ways switches complete all as specified and directed. 166 All as per Srl item No 161 here in before but for call bell pointcomplete all as specified and directed. 167 S&F in replacement modular switch 5/6 Amp single pole one way, one module complete all as specified and directed. 168 S&F in replacement modular switch socket combinatin 5 pin, type 5/6 Amp 5 in 1 flush type complete all as specified and directed. 169 S&F in replacement modular switch socket combinatin 6 pin, type 5/16 Ampflush type complete all as specified and directed. 170 S&F in modular switch 5/6 Amps single pole two ways complete all as specified and directed. 171 S&F in modular socket outlet 5 pin 5Amps flush type complete all as specified and directed. 172 S&F in replacement industrial socket metal clad plug and socket with MCBs single pole 20 Amp complete all as specified and directed. 173 S&F in modular bell push 5 Amp complete all as specified and directed. 174 S&F in replacement ofmodular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed. 175 S & F switch piano flush type 5/6 Amps single pole one waycomplete all as specified and directed. 176 S & F switch socket combination 5 Pin, 5/6 Amps flush type complete all as specified and directed. 177 S & F switch socket combination 6 Pin, 15/16 Amps flush type complete all as specified and directed. 178 S & F AC 230 single pole Bell ding dong type complete all as specified and directed. 179 S & F ceiling rose surface bakelite 65 x 50mm three terminals complete all as specified and directed. 180 S & F in replacement of existing light fitting withLED batten with aliminium housing andintegrated electronic driver,20 watt having input voltage AC90-300V, 50 Hz , 6500K, and all other accessories including connection with flexiblecable copper conductortwin coreof size 23/.2 mm upto ceiling rose/connector complete all as specified and directed. 181 S&F in replacement water tight bulk head fitting comprision of connector galvanised cast iron back plate, weather proof enamelled gallery, glass well, and including 10 watt LED lampcomplete all as specified and directed. 182 S&F in replacement compact and decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1X10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified and directed. 183 S&Fin replacement of security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed. 184 S & F in replacement LED Bed side Light (White 3000k) 3 watt with flexible arm suitable for reading complete all as specified and directed. 185 S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed. 186 S & FLED lamp 9W for angle holdercomplete all as specified and directed. 187 S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn inexistingPVC conduictincluding 6.00 Sq mm (Nominal Area) copper cableas earthcontinuity conductor including necessary connections, PVCflexible pipes are used in pannel board while connecting the cablecomplete all as specified and directed. (Note : PVC cable and PVC conduit shall be ISI marked) 188 S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 4 sqmm (Nominal Area) FRLSH stranded copper conductor drawn inexistingPVC conduictincluding 4.00 Sq mm (Nominal Area) copper cableas earthcontinuity conductor including necessary connections, PVCflexible pipes are used in pannel board while connecting the cablecomplete all as specified and directed. (Note : Two lengths of 4.0 sqmm cable for one length 4.0 sqmm earth cable alongwith PVC conduit will be measured as one running length) 189 S & F in repairs sheet metal enclosure for double door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounting VTPN 4 Way 415 Volts, ISI marked 250 amps bus bar stove enameled dust and vermin proof, IP:43 protection suitable for incorporation FP MCCB (V-Tech) N3 Frame upto 250A, Isolators and Including give connection with wire and cable etc complete all as specified and directed. 190 S&F in repairs MCCB 4 pole 63 Amps with breaking capacity 16KA, Fixed TM and 415 volts AC supply ISI markedcomplete all as specified and directed. 191 S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed. 192 S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 4 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed. 193 S & F in repairs MCB ‘C’ series type suitable for 240 volts, AC supply32Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. 194 S & F in repairs MCB ‘C’ series type suitable for 240 volts, AC supply5 to 32Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. 195 S & F in repairs MCB ‘B’ series type suitable for 240 volts,10KA, AC supply20 Amps, single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. 196 S & F in repairs MCB ‘B’ series type suitable for 240 volts,10KA, AC supply6 to 32 Amps, single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. 197 M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mmthick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GIand protection by provisionof GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed. 198 S&F Taking down fan, sealing cable end, dismantling blades and removing fan and blades to storecomplete all as specified and directed. 199 M&L for Painting of ceiling fans complete in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust complete all as specified and directed. 200 Hanging only ceiling fan (M.D. supply) and connection up including provision of cable from ceiling rose or connectior to fan complete all as specified and directed. 201 S&F exhaust fan made of sturdy engineering plastic of 250mm sweep 240 volt,complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1:4) white washing matching with existing colour completed all as specified and directedNote : Exhaust fans shall be ISI marked. 202 S&F Rigid non-metalic PVC conduit 20mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends fixing accessories such as couplers, lock nuts, saddles pipe hooks etc. completed all as specified and directed.Note : Exhaust fans shall be ISI marked. 203 S&F TV socket having holes for 20mm conduit entry for tv connection completed all as specified and directed. 204 Supply and lay jointing and testing and commissioning in replacement of 25 Sqmmx4 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed. 205 Supply and lay jointing and testing and commissioning in replacement of 16Sqmmx 2 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed. 206 Supply and lay GI Pipe 50mm light grade of size cable protection in wall trencehes or any situation including clamp nut bolt etc complete all as specified and directed. 207 Supply and lay GI Pipe 40mm light grade of size cable protection in wall trencehes or any situation including clamp nut bolt etc complete all as specified and directed. 208 Supply and filling in Sand for Cable protection complete all as specified and directed.(Note : Punned thickness shall be measured for payment) 209 Supply and lay standard size bricks sub class B as in cable protection complete all as specified and directed. 210 Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr depth for laying of cablescomplete all as specified and directed. 211 Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cmcomplete all as specified and directed. 212 Removal of Excavated material n exc 50mtr and depositing complete all as specified and directed. 213 S&F in switch flame proof rotary type with terminatin box in LM6, 16A, single pole 250V complete all as specified anddireced. 214 S&F of flameproof cum waterproof LED bulk Head fitting of 15W, IP 66 protection of Cast Aluminium alloy material and Heat and Impact resistance toughen A clear glass having Anti corrosive epoxy powder coated finish complete with all accessories pre wired asnd inlcuding connection up with three core flexible copper condutor cable with suitable size complete all as specified anddireced. 215 S&F LED light fitting 1x16/20 Watt flame proof, CMRI certififed recommended for gas/vapor group of IIA & IIB, Zone 1 & 2 and IP 65 protection with die cast aluminium hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc complete with all accessories prewired and includding connecting up with three core flexible copper conductor cable withcomplete all as specified anddireced. 216 S&F post top lantenr LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection wit impact and corrosion resistant complete with driver and lamp complete all as specified anddireced.
