Tender For The Work Sanctioned Under Additional Business Plan 2024-25 In Area Under Electricity Urban Distribution Division-Ii, Gorakhpur; 2 Loading, unloading and safe carriage of following materials from Store Centre, Gorakhpur to JE dump Store and JE dump Store to work site with proper stacking :- 3 3x185 mm2 XLPE 11 KV 4 Cable jointing kit 11 KV XLPE 3X185 sq mm 5 Cable jointing kit 11 KV XLPE 3X185 sq mm S/T 6 S.T. Pole 11 Mtr. Long 7 11 KV Dropper Channel 8 11 KV Top Channel 9 11 KV Pin Insulator 10 11 KV pin with net 11 Earthing Complete 12 Supply offollowing material/fitting complete in all respect :- 13 Holding clamps for top, dropper, t-off etc 14 GI Nuts & Bolts off size 15 G.I Pipe dia 150 mm 16 The excavation of 2 No foundation pit of size 750mmX450mm and having depth of 1/6th of the full length of the pole. Fabrication & erection of double Pole with fixing of necessary clamps & accessories (Top Channel, Dropper Angle etc.) as per required. All required materials such as Holding clamp/STP clamp, Nuts & Bolts off size etc will be provided by the contractor.Grouting of Pole in cc 1:4:8 (Cement, sand & 40 mm brick ballast), Grouting will be done in the block ofsize 450x450 mm x depth upto ground level and backfilling of pits with mud completely and leveling etc (Material provided by Contractor).Making plinth around Pole height 300 mm above ground level with top 100 mm is kept tapered so that no rainwater gets accumulated on the top. All work will be done as per RESPO norms & relevent IS Specification. 17 Painting of Pole by double coating Aluminium & Red oxide paint. Paint will beprovided by contractor 18 Earthing of ST Pole by MS earthing Rod & 6 SWG earthing Wire as per RESPO norms. 19 Laying and dressing of under ground 11 KV 3X185 sq mm XLPE Cable by Horizontal drilling method as per RESPO norms. The Depth of horizontal drilling shall be between 2 to 3 meters or as per site required. 20 Errection of 11 KV 3X185 sq mm XLPE Cable Jointing Kit with complete work 21 Making Loop alongwith dressing, Marking, Tagging and Hoisting of cable on Single/Double pole using G.I. Pipe 6dia 3 mtr. Long with complete work. 22 fo|qr uxjh; forj.k [k.M&f}rh; xksj[kiqj ds vUrxZr fctusl Iyku esa Lohd`r u;s 250 ds0oh0,0 forj.k ifjorZdksa dh LFkkiuk ds dk;ksZ dks lseh VuZdh ds vk/kkj ij djk;s tkus gsrq dk;Z dk fooj.k %& 23 Loading, unloading and safe carriage of following materials from Store Centre, Gorakhpur to JE dump Store and JE dump Store to work site with proper stacking :- 24 250 KVA Transformer 25 11 KV XLPE Cable 3X70 sq mm 26 11 KV C/J Kit 3X70 sq mm 27 ST Pole 09 M long 28 ST Pole 11 M long 29 MS Top Channel (125x65x2240) mm 30 MS angle (Dropper) 100X50X2028 mm 31 ACSR Weasel conductor 32 ACSR Dog conductor 33 11 KV Pin Insulator with pin 34 11 KV Disc insulaor with fiitings 35 LT AB Cable (3X150+1X120+1X16) sq mm 36 LT Cable 1X35 sq mm 37 11 KV Fuse set 38 11 KV T-Off Channel 39 Stay complete (Stay rod 16X1800 mm, stay wire 5 kg, stay clamp, bolt & nuts) 40 Earthing complete 41 LT Cable 1X240 sq mm 42 Supply offollowing material/fitting complete in all respect :- 43 LT Three Phase Distribution box 44 Clamp for LT Three Phase DB Box 45 Suspension Clamp with I hook (Insulated) 46 Dead end Clamp with I hook (Insulated) 47 Piercing Connector (Insulated) 48 Shackle insulator 49 LT Clamps 50 Holding Clamp for top, dropper channel Fuse set etc with nuts & bolts 51 Copper Z Calmp 52 GI Nuts & bolts of different sizes 53 Al Lugs 54 G.I Pipe dia 6 inch 55 The excavation of 2 No foundation pit of size 750mmX450mm and having depth of 1/6th of the full length of the pole. Fabrication & erection of double Pole with fixing of necessary clamps & accessories (Top Channel, Dropper Angle etc.) as per required. All required materials such as Holding clamp/STP clamp, Nuts & Bolts off size etc will be provided by the contractor.Grouting of Pole in cc 1:4:8 (Cement, sand & 40 mm brick ballast), Grouting will be done in the block ofsize 450x450 mm x depth upto ground level and backfilling of pits with mud completely and leveling etc (Material provided by Contractor).Making plinth around Pole height 300 mm above ground level with top 100 mm is kept tapered so that no rainwater gets accumulated on the top. All work will be done as per RESPO norms & relevent IS Specification. 56 The excavation of foundation pit of size 750mmX450mm and having depth of 1/6th of the full length of the pole. Fabrication & erection of PCC Pole with fixing of necessary clamps & accessories as per required. All required materials such as Holding clamp/PCC/LT clamp, F-Bracket, LT shacle insulator, Nuts & Bolts off size etc will be provided by the contractor.Grouting of Pole in cc 1:4:8 (Cement, sand & 40 mm brick ballast), Grouting will be done in the block ofsize 450x450 mm x depth upto ground level and backfilling of pits with mud completely and leveling etc (Material provided by Contractor).All work will be done as per RESPO norms & relevent IS Specification. 57 Painting of Pole by double coating Aluminium & Red oxide paint. Paint will beprovided by contractor 58 Earthing of ST Pole by MS earthing Rod & 6 SWG earthing Wire as per RESPO norms. 59 Fabrication, errection, commissioning & Testing of 250 KVA T/F on Plinth with all accessories including make its LT and HT connection. All neessary materials will be supplied by the Contractor. 60 Chemical earthing of Transformer (Body+Neutral) as per IS Code 3043 - 1987 specification (Materials will be provided by contractor) 61 Erection and grouting of stay in CC ratio 1:4:8 of Cement, Sand and Stone Ballast including cost of grouting material with nozelling and binding of stay wire (Complete work) 62 Laying of ACSR Dog/Weasel conductor for LT/HT Line with fixing of LT Clamps/other clamps, Shackle insulator and nuts&bolts off size as per required. 63 Laying and dressing of under ground 11 KV 3X70 sq mm XLPE Cable by Horizontal drilling method as per RESPO norms. The Depth of horizontal drilling shall be between 2 to 3 meters or as per site required. 64 Making Loop alongwith dressing, Marking, Tagging and Hoisting of cable on Single/Double pole using G.I. Pipe 6dia 3 mtr. Long with complete work. 65 Erection of 11 KV 3X70 Sq.mm. Cable Jointing Kit 66 Erection of 11 KV Fuse set 67 Construction of T/F plinth of size 2x2x1.2 M with the help of first class brick & 9 masonary in the ratio 1:4 cement & sand coarse. Filling the structure completely andplastering outer surface as per RESPO norms. Top of the plinth covered with 4 RCC Slab of ratio 1:1.5:3 (Cement, sand & concrete) grouting with 2 No ISMC size 125X65X6 MM (confirming to IS 808:1989) of 2000 mm long for resting. All required materials will be provided by the contractor. 68 Grill fencing of 11/0.4 KV S/S shall be made of rectangular of size & height approx 2 meter as per site requirement with fabrication 50X50X5 mm angel the frame is also have 1 No Horizontal runner of MS flat 40x5 welded in middle to support of grill, having a gate on road side must have provision of locking arrangement. The work is including painting of fencing as per norms. Work will be done as per RESPO specification. 69 Laying & sagging of ABC (3X150+1X120+1X16) Sq.mm. Cable of LT Line with fixing of Distribution Box with Clamp, Insulated Dead end clamp with I hook, Suspension clamp with I hook(Insulated), LT insulated Piercing connector, XLPE 1X35 Sq.mm. Al. cable for enerzing DB,XLPE 1X16 Sq.mm. Al. cable for giving connection to Street Light and nuts&bolts off size by the contractor. 70 Supply and Complete Installation of 2 Nos. Henley Type Tailless Unit 300 AMP in Box using LT XLPE 1X240 Sq.mm. Cable,LT Crimping Lug, GI Nuts & Bolts etc (as per site requirement) on 11/0.4 KV Distribution Transformer. (Only LT XLPE 1X240 Sq.mm. Cable will be provided by Department)Specification of Henley Type Tailless Unit 300 AMPdescribed as below-1. Henley Type MS Sheet duly painted grey enameled paint- MS of 18 SWG (54X4.5 inches) with holes as per requirement2. 6 No. Insulator- Made of White Glazed Porcelain3. 6 No. Copper Spring Contact- 32X3.7 mm Made of Copper4. 3 No. L Contact - Brass5. 3 No. Metal Part Connector For Holding Busbar- Brass6. 1 No. Casted Patti- M.S.7. 1 No. Neutral- Brass8. Iron Clip, Bolt, Nuts, Washer and Screw etc for Tightening- All Galvanized9. Copper Bus Bar Strip- 500X50X5 mm (3 Nos.Copper Busbar Strip to be used on 2 Nos. Tailless unit)10. Aluminium Bus Bar Strip- 500X50X5 mm (1 No)All work will be done as per RESSPO Norms & relevent IS Specification. 71 Supply, fabrication, erection of LT Pillar Box for Tailless Unit after making Plinth of Height 300 mm above ground level LT Pillar Box Size- 1650X1050X520 mm with Gate and Proper Locking arrangement (Canopy of 15 Degree )All work will be done as per RESSPO Norms & relevent IS Specification. 72 fo|qr uxjh; forj.k [k.M&f}rh;] xksj[kiqj ds {ks= esa fctusl Iyku esa Lohd`r vkj0,e0;w0 yxkus ds dk;Z dks lseh VuZdh ds vk/kkj ij djk;s tkus gsrq dk;Z dk fooj.k %& 73 Loading, unloading and safe carriage of following materials from Store Centre, Gorakhpur to JE dump Store and JE dump Store to work site with proper stacking :- 74 3x185 mm2 XLPE 11 kV 75 Cable jointing kit 11 kV XLPE 3X185 sq mm 76 11 kV, 630, 21 kA Ring Main Unit, 3 Way 77 Laying and dressing of under ground 11 KV 3X185 sq mm XLPE Cable by Horizontal drilling method as per RESPO norms. The Depth of horizontal drilling shall be between 2 to 3 meters or as per site required. 78 Errection of 11 KV 3X185 sq mm XLPE Cable Jointing Kit with complete work 79 Erection of 11 kV Ring Main Unit 80 Plinth for 11 kV Ring Main Unit 81 Earthing (Pipe Type) for 11 kV Ring Main Unit 82 fo|qr uxjh; forj.k [k.M&f}rh;] xksj[kiqj ds {ks= esa fctusl Iyku esa Lohd`r ttZj ,0ch0 dsfcyksa dks ifjofrZr@mPphdj.k ds dk;Z dks lseh VuZdh ds vk/kkj ij djk;s tkus gsrq dk;Z dk fooj.k %& 83 Loading, unloading and safe carriage of following materials from Store Centre, Gorakhpur to JE dump Store and JE dump Store to work site with proper stacking :- 84 LT AB Cable (3X150+1X120+1X16) sq mm 85 ST Pole 9 mtr Long 86 LT Cable 1X35 sq mm 87 Earthing complete 88 Supply offollowing material/fitting complete in all respect :- 89 LT Three Phase Distribution box 90 Clamp for LT Three Phase DB Box 91 Suspension Clamp with I hook (Insulated) 92 Dead end Clamp with I hook (Insulated) 93 Piercing Connector (Insulated) 94 GI Nuts & bolts of different sizes 95 The excavation of foundation pit of size 750mmX450mm and having depth of 1/6th of the full length of the pole. Fabrication & erection of PCC Pole with fixing of necessary clamps & accessories as per required. All required materials such as Holding clamp/PCC/LT clamp, F-Bracket, LT shacle insulator, Nuts & Bolts off size etc will be provided by the contractor.Grouting of Pole in cc 1:4:8 (Cement, sand & 40 mm brick ballast), Grouting will be done in the block ofsize 450x450 mm x depth upto ground level and backfilling of pits with mud completely and leveling etc (Material provided by Contractor).All work will be done as per RESPO norms & relevent IS Specification. 96 Painting of Pole by double coating Aluminium & Red oxide paint. Paint will beprovided by contractor 97 Earthing of ST Pole by MS earthing Rod & 6 SWG earthing Wire as per RESPO norms. 98 Laying & sagging of ABC (3X150+1X120+1X16) Sq.mm. Cable of LT Line with fixing of Distribution Box with Clamp, Insulated Dead end clamp with I hook, Suspension clamp with I hook(Insulated), LT insulated Piercing connector, XLPE 1X35 Sq.mm. Al. cable for enerzing DB,XLPE 1X16 Sq.mm. Al. cable for giving connection to Street Light and nuts&bolts off size by the contractor. 99 Dismentling of old existing A.B. Cable 100 Dismentling of old existing ST Pole 101 Carriage of old existing conductor & Pole from work site to store centre 102 Disconnection & reconnection of consumer service cables 103 fo|qr uxjh; forj.k [k.M&f}rh;] xksj[kiqj ds {ks= esa fctusl Iyku esa Lohd`r ttZj ,0ch0 dsfcyksa dks ifjofrZr@mPphdj.k ds dk;Z dks lseh VuZdh ds vk/kkj ij djk;s tkus gsrq dk;Z dk fooj.k %& 104 Loading, unloading and safe carriage of following materials from Store Centre, Gorakhpur to JE dump Store and JE dump Store to work site with proper stacking :- 105 ACSR Rabbit Conductor 106 ST Pole 11 mtr long 107 11 KV Pin Insulator with pin 108 11 KV Disc insulaor with fiitings 109 11 KV V cross arm 110 11 KV T-Off Channel 111 Stay complete (Stay rod 16X1800 mm, stay wire 5 kg, stay clamp, bolt & nuts) 112 Earthing complete 113 Supply offollowing material/fitting complete in all respect :- 114 F Bracket 115 Holding Clamp 116 Nuts & bolts of different sizes 117 The excavation of foundation pit of size 750mmX450mm and having depth of 1/6th of the full length of the pole. Fabrication & erection of PCC Pole with fixing of necessary clamps & accessories as per required. All required materials such as Holding clamp/PCC/LT clamp, F-Bracket, LT shacle insulator, Nuts & Bolts off size etc will be provided by the contractor.Grouting of Pole in cc 1:4:8 (Cement, sand & 40 mm brick ballast), Grouting will be done in the block ofsize 450x450 mm x depth upto ground level and backfilling of pits with mud completely and leveling etc (Material provided by Contractor).All work will be done as per RESPO norms & relevent IS Specification. 118 Painting of Pole by double coating Aluminium & Red oxide paint. Paint will beprovided by contractor 119 Earthing of ST Pole by MS earthing Rod & 6 SWG earthing Wire as per RESPO norms. 120 Laying of ACSR Rabbit/Dog/Weasel conductor for LT/HT Line with fixing of LT Clamps/other clamps, Shackle insulator and nuts&bolts off size as per required. 121 Dismentling of old existing Line 122 Dismentling of old existing ST Pole 123 Carriage of old existing conductor & Pole from work site to store centre
