|
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc. 15cm thickness below or above ground level (including floor finishes) complete all as specified and directed by Engineer-in-Charge. |
| 2 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store/credit to contractor complete all as specified and directed by Engineer-in-Charge. |
| 3 | M&L for 25 mm thick PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in floors complete all as specified and directed by Engineer-in-Charge. |
| 4 | M&L for vitrified Ceramic tiles dark shade 10mm thick (square/rectangular) polished, area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge. |
| 5 | M&L for vitrified tiles dark shade Granite /Marble /wood textures 10 mmthick tiles in vertical surfaces n. exe0.36 Sqm, over and including 10mm thick backing coat in CM 1:4set and jointed in neat cement slurry and pointed inwhite or colored cement to match complete all as specified and directed by Engineer-in-Charge. |
| 6 | M&L for non skid ceramic coloured joint free tiles 7 to 8mm thick (square/ rectangular), area of each tiles exceeding 0.18 but not exceeding 0.38 Sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:4) laying floor finish complete all as specified and directed by Engineer-in-Charge. |
| 7 | S&F coloured glazed ceramic tiles on vertical surfaces 300x200x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 8 | S&F 450x350x7mm size coloured glazed wall tiles setandjointed in neat cement slurry and pointed with cloured cement to match as in vertical surfacesover and including 15mm thick rendering in cement mortar 1:4 on vertical surfaces to receive wall finishescomplete all as specified and directed by Engineer-in-Charge. |
| 9 | M&Lfor 20mm thick granite tiles (any type)in one piece machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 10 | M&L for machine cut kota slabs flooring 20-25 mm thick over and including 15 mm thick screed bed in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge. |
| 11 | M&L for machine cut kota slab flooring 20-25 mm thick in one piece in riser of steps, skirting, dado and pillars, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick rendering in cement mortar 1:4 on vertical surface to receive wall finishescomplete all as specified and directed by Engineer-in-Charge. |
| 12 | M&L for rounding to edges of stone slab such as steps cooking plateform and other similar situations complete all as specified and directed by Engineer-in-Charge. |
| 13 | M&L for 75mm thick,PCC 1:3:6 type C-2(using 40mm graded crushed stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 14 | Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key and scrubbing down with water complete all as specified and directed by Engineer-in-Charge. |
| 15 | M&L for 10mm thick cement plaster on fair faces of brick work or concrete surfacesincement mortar 1:6 finishing the surface even & smooth w/o using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 16 | M&L for 15mm thick cement plaster on fair faces of brick work or concrete surfacesincement mortar 1:4, finishing the surface even & smooth w/o using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 17 | M&L for applying two coats of OBD over one coat of alkali resistant primer (application of approved wall care putty 3mm thick to smooth & even surface) onnew plastered surfaces including preparation of surfaces complete all as specified and directed by Engineer-in-Charge. |
| 18 | Material and labour for applying two coats of OBD to old treated plastered surfaces of wall including preparation of surfaces (by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and gresay spots)(application of approved wall care putty 1mm thickto smooth & even surface) complete all as specified and directed by the Engineer-in-Charge. |
| 19 | M&L for two coats of cement base paint over a coat or alkali resistance primer on newly plastered surface of wall including preparation of surfaces complete all as specified and directed by Engineer-in-Charge. |
| 20 | M&L for two coats of cement base paint on old plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer-in-Charge. |
| 21 | Taking down chowkhats or frames not exc. 1.5 Sqm with shutters (without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge. |
| 22 | Taking down chowkhats or frames with shutters (without taking shutter from the frame) exceeding 1.5 sqm and not exceeding 4.00 sqm each complete all as specified and directed by Engineer-in-Charge. |
| 23 | M&L for 2ndclass hardwood, plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge. |
| 24 | S&F mild steel work in bands, straps, hold fast, support or stays for rainwater pipes, and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engineer-in- Charge. |
| 25 | S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelaminated PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings complete all as specified and directed by Engineer-in-Charge. |
| 26 | S&F factory made solidPVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and gap insert for top rail and bottom rail paneling of plain colour PVC to sheet to be fitted in the MS frame welded / sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed by Engineer-in-Charge. |
| 27 | S&F 2nd class hard wood 35mm thick factory made plain framed panelled shutterswith lock rail and pannel of 9mm BWP commercial ply or 12mm veneered particle board with commercial faces veneers on both faces the size of rails and stile as per IS-1003 (Part-1) kilne seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge. |
| 28 | S&F 2nd class hardwood glazed and skeleton shutters 35mm thick prepared to received guage etc.(divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass or guage etc.Size of members of shutters as per SSR Part-I Section VIII clause 8.24(a) complete all as specified and directed by Engineer-in-Charge. |
| 29 | S&F aluminium anodised barrel tower bolts extruded section of size 200 mm complete all as specified and directed by Engineer-in-Charge. |
| 30 | S&F aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts ofsections or cast-aluminium extruded alloy and fixed complete all as specified and directed by Engineer-in-Charge. |
| 31 | S&F butt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge. |
| 32 | S&F mild steel 300mm size ordinary rat tail pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge. |
| 33 | Hacking out old or broken glass (any thicknesssize quality or description) from steel frames or stone concrete or brick surrounds glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-Charge. |
| 34 | S&F 4mm thick sheet glass of ordinary quality and glazing with oil putty in n. exc 0.5sqm each in pane complete all as specified and directed by Engineer-in-Charge. |
| 35 | S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed by Engineer-in-Charge. |
| 36 | Taking up or down steel tubing and connection including cleaning for refixing or removal to store for 15mm bore of pipe complete all as specified and directed by Engineer-in-Charge. |
| 37 | S&F 15mm bore GI tubing medium grade with all fittings fixed to walls ceiling or laid in trenches complete all as specified and directed by Engineer-in-Charge. |
| 38 | Fixing only 15mm bore GI tubing medium grade with all fittings fixed to walls ceiling or laid in trenches complete all as specified and directed by Engineer-in-Charge. |
| 39 | Taking up or down steel tubing and connection including cleaning for refixing or removal to store for 20mm bore of pipe complete all as specified and directed by Engineer-in-Charge. |
| 40 | S&F 20mm bore GI tubing medium grade with all fittings fixed to walls ceiling or laid in trenches complete all as specified and directed by Engineer-in-Charge. |
| 41 | Fixing only 20mm bore GI tubing medium grade with all fittings fixed to walls ceiling or laid in trenches complete all as specified and directed by Engineer-in-Charge. |
| 42 | S&F in repairs PVC valve less 10 litre capacity syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engr-in -Charge. |
| 43 | S&F in repairs vitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and connection to flushing cistern, brackets, flushing pipeetccomplete all as specified and directed by Engineer-in-Charge. |
| 44 | Dismantling water storage tanks of any description/ exc 250 & n exc 500 litres capacity and removing from site complete all as specified and directed by Engineer-in-Charge. |
| 45 | S&F rotational moulded polyethylene 500 liters capacity waterstorage tanks (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ballcomplete all as specified and directed by Engineer-in-Charge. |
| 46 | Supply and fixing in repairs grating doom 125mm dia with waste hole of PTMT weight not less than 40mm each complete all as specified and directed by Engineer-in-Charge. |
| 47 | S&F in repairs PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge. |
| 48 | S&F in repair PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge. |
| 49 | S&F in repair PVC bends 110 mm bore complete all as specified and directed by Engineer-in-Charge. |
| 50 | S&F in repair PVC bends 75 mm bore complete all as specified and directed by Engineer-in-Charge. |
| 51 | S&F looking mirror 600mm x 450mm bevelled edge mirror of selected quality glass 5mm thick mounted on 6 mm thick AC building board or commercial ply and fixed to wooden plugs with CP brass screws and cup washers etc, fixed in repairs, complete all as specified and directed by Engineer-in-Charge. |
| 52 | S&F in repairs 15 mm bore fancy typeCP bib tapscast copper alloy with crutch or butterfly handle , screwed down for iron pipe complete all as specified and directed by Engineer-in-Charge. |
| 53 | S&F in repairs 15 mm borebrass CP mixer for mixing hot and cold waterscrewed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engineer-in-Charge. |
| 54 | S&F in repairs 15 mm bore CPstop/angle valve cast copper alloy screwed down, high pressure with crutch or butterfly handlefancy typecomplete all as specified and directed by Engineer-in-Charge. |
| 55 | S&F in repairs health faucet CP Brass hand Jet Shower 15mm bore dia and 1500mm long CP pipe complete all as specified and directed by Engr-in-Charge. |
| 56 | M&L for preparation of new or untreated wood or wood based surfaces of any description exc.10 cm. in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 57 | M&L for preparation of old surfaces of ceiling plastered or unplastered including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of white wash on ceiling complete all as specified and directed by Engineer-in-Charge. |
| 58 | M&Lfor preparation of old painted wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 59 | M&Lfor preparation of old painted steel surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 60 | Dismantling plain or corrugated steel sheeting any gauge, thickness including roof covering etc. complete all as specified and directed by Engineer-in-Charge. |
| 61 | S&F forpre-painted galvalume aluminium zinc coating GIbased corrugated steel sheets 0.50 mm thick of anycolour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge. |
| 62 | S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheets 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge. |
| 63 | S&F in repairs for weather boarding in 2nd class hardwood clean swan , plain, feather edges, 15 mm to 20 mm thick and fixed with 30 mm laps joints complete all as specified and directed by Engineer-in-Charge. |
| 64 | Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs including cover fillets etc. complete all as specified and directed by Engineer-in-Charge. |
| 65 | S&F for anodised aluminium snap grid of size 605 x605 mm frame work for false ceiling including straining with GI wire4 mm thick complete all as specified and directed by Engineer-in-Charge. |
| 66 | S&F for 10mm thick PVC insulation panels with EPS stuck to 1 mm thick plain PVC sheet suitably placed in false ceiling grid made of aluminumGI/MS as per specification and drawing complete all as specified and directed by Engineer-in-Charge. |
| 67 | Taking down carefully old U/S point wiring copper/Aluminium (light/ fan /sockets/power) complete with switches, sockets, fan regulators, ceiling roses, lamp holders, brackets, removing material to store for keeping in safe custody or credit to contractor and making good to disturbed surfaces complete all as specified and directed by Engineer-in-Charge. |
| 68 | M&L for concealed point wiring with FRLS PVC insulated, un-sheathed, multi stranded copper conductor cable of 1.5sqmm size, 1100volts, drawn through and including non metalic rigid PVC Conduit not less than 25mm with all accessories fixed on wall/ceiling/truss including FRLS PVC insulated, unsheathed, multi stranded copper conductor cable of 1.5sqmm size asearth continuty conductor connected to common earth dolly including required numbers and size of Sunken boxes/ hylam sheet fixed on wall for fixing the switches, switch sockets, sockets, regulators etc complete all as specified for (a)One light point controlled by one 5AswitchNOTE: a) Colour coding shall be followed as given below:-i) Phase - Red/Yellow/Blueii)Neutral - Blackiii) Earth - Greenb) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit of suitable size as directed by EIC. |
| 69 | (b) Description all as per item no. 68 above but for One Fan point controlled by one 5Aswitch complete all as specified and directed by Engineer-in-Charge. |
| 70 | (c)Description all as per item no. 68 above but for One 5A flush type switch socket point on same boardboard complete all as specified and directed by Engineer-in-Charge. |
| 71 | (d)Description all as per item no. 68 above but forOne5A flush type switch socket point on independent board complete all as specified and directed by Engineer-in-Charge. |
| 72 | (e) Description all as per item no. 68 above but for One Bell point control by one 5A bell push switch complete all as specified and directed by Engineer-in-Charge. |
| 73 | (f) Description all as per item no. 68 above but for One Exaust Fan point controlled by one 5Aswitch complete all as specified and directed by Engineer-in-Charge. |
| 74 | M&L for concealed point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 2.5 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid,not less than 25mm PVC condiut with all accessories such as tee, bends, elbow, reducers, junction box etc fixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including sunken boxes/ hylam sheet in any module complete for One 5 pin, 15A switch socket combination on the independent board complete all as specified and directed.Note: Colour coding shall be folowed asi) Phase - Red/Yellow/Blueii)Neutral - Blackiii) Earth - Greenb) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit of suitable size as directed by EIC. |
| 75 | S&F ceiling rose surface bakelite 65 x 50mm, flush type, 3 terminals complete all as specified and directed by Engr-in-charge. |
| 76 | S&F switch piano flush type single pole one way, 5/6 Amps complete all as specified and directed by Engineer-in-Charge. |
| 77 | S&F Bell push, 5/6 Amps, 230 volts SP complete all as specified and directed by Engineer-in-Charge. |
| 78 | Supply and fix switch sockets combination 5 pin 5 Amps flush type 230 Volts ACcomplete all as specified and directed by Engineer-in-Charge. |
| 79 | Supply and fix switch socket combination 2 in 1, 5 pin, 5 & 15 Amps flush type universal controlled by one switch flush type 230 Volts ACcomplete all as specified and directed by Engineer-in-Charge. |
| 80 | S&Ffan regulator electronic dimmer, 450w,230V flush type and making all necessary connections complete all as specified and directed by Engineer-in-Charge. |
| 81 | S&F ding dong bell AC 230Voltssingle polebell 50 Hzcomplete all as specified and directed by Engineer-in-Charge. |
| 82 | S&Flamp holder PVC/polycarbonate insulated body type complete all as specified and directed by Engineer-in-Charge. |
| 83 | Supply and fixing in replacement LED9 watt pin type bulb complete all as specified and directed by Engr-in-Charge. |
| 84 | Supply and fixing in repairs LED lights fitting 1x 20 W, 220V-230V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge. |
| 85 | Supply and fixing in repairs LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V to 230V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. |
| 86 | S&F of double door type vertical type TPN DB 4 Way ,415Vwith 200Amp busbar, with metalic double door type IP 43 IK 09 protectionsuitable for housing MCCB\"s FP & SPN etc all as specified and directed by EIC. Note : DBs shall be concealed in wall where ever posible including old DB taking out and making good the surface to match with surrounding by plaster, make existing colour complete all as specified and directed by Engineer-in-Charge. |
| 87 | S&F MCCB, FP 63 Amps, 415V,16KA, complete all as specified and directed by Engineer-in-Charge. |
| 88 | Supply and fixing in repairs of 240V, 10 KA \"B\" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge. |
| 89 | Disconnecting & taking down old Unservicable cable & Supply and lay in repairs new cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core complete all as specified and directed by Engr-in-Charge. Note:1: The cost of aluminium thimbles/lugs and cable gland etc is included in quoted rate and no extra payment will be made for it. 2. The rate includes passing of cable through road wall etc The quoted rate also includes making the existing surface good by the contractor. |
| 90 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft / loose soil for laying cables / pipes / erection of poles etc. complete all as specified and directed by Engr-in-Charge. |
| 91 | Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge. |
| 92 | Returning filling in soil including spreading leveling watering well ramming in layers not exceeding 25 cm each complete all as specified and directed by Engr-in-Charge. |
| 93 | Supply and lay in trenches river sand including spreading / levelling, cushioning for underground cables complete all as specified and directed by Engr-in-Charge. |
| 94 | M&L for GI tubing light grade 40 mm diawith all fittings laid in trenches orfixed on wall along pole complete for protection of electric cable complete all as specified and directed by Engr-in-Charge. |
| 95 | M&L for sub class\"B\"brickfor covering protectionto the eletric cablelaiddry flat transversallyalongthe lengthof cableon sandcushioningwith widthequal to lengthof brickcomplete all as specified and directed by Engr-in-Charge. |
| 96 | Supply and fixing in repairs exhaust fan made of sturdy Engineering plastic/steel body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete including cutting and making good existing surface to match complete all as specified and directed by Engr-in-Charge. |
| 97 | M&L in replacement sub-main wiring with 2 runs of 10 sqmm copperconductor cable (FRLSgrade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including non metalic rigid PVC casing and caping/Conduit not less than 25mm with all accessories fixed on wall/ceiling/truss etc as required, including one run of 10 sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unserviceable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black(iii) Earth - green .(b) Three runs of 10 sqmm cable and one run of conduit/casing capping shall be measured as one unit length for measurement and payment purpose. |
| 98 | Material and Labour for Earthing complete with MS plate electrode of size 600 X 600 X 6 mm buried directly and preferably vertically in ground (earth pit not less than 2.25 mtrs deep below ground level ) with top edge of the plate not less than 1.5 Mtrs below ground level, connected to connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate no. 3 of SSR Part-I, connected to Earthing test point including earth work, 1:3:6 C1 PCC chamber, 1:2:4 B1 PCC cover with 8 mm dia steel bars at 100 mm C/C suitable size of GI pipe for earth lead protection and watering, water funnel etc. complete all as specified and directed by Engr-in-Charge. |
