|
| 1 | Excavation over areas not exc 1.5m deep in hard/dense soil for foundation etc. and getting out, complete all as specified and directed. |
| 2 | Removing and disposing off the excavated material/soil out side MD Land, complete all as specified and directed.Note: For payment pirposes, quantity of excavation after deduction of the quantity of returning filling, shall only be payable under this item. |
| 3 | Grubbing up tree trunk including cutting of trunk portion protruding over ground, digging out roots, filling holes and levelling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc. 50 m and clearing site, girth of tree Exc.30cm and n exc. 100cm |
| 4 | M & L Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out In Hard/dense soil.completed all as specified |
| 5 | Excavating in trenches, by mechanical means(hydraulic excavator) n exc 1.5 m wide and n exc 1.5 m in depth; for footing, Plinth Beam & Dwarf Wall, etc. n exc 10 sq m on plan and getting out in Hard/dense soil. |
| 6 | Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in soft/loose soil including taking out brick protection etc complete all as specified and directed. |
| 7 | Excavating in trenches, by mechanical means(hydraulic excavator) exc 1.5 m wide and n exc 3.0 m in depth; for footing, Plinth Beam & Dwarf Wall, etc. n exc 10 sq m on plan and getting out in Hard/dense soil. |
| 8 | M & L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface |
| 9 | M & L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) |
| 10 | M & L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall |
| 11 | M & L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area |
| 12 | M & L Cement concrete in foundations, filling and mass concrete 1:4:8 using 40 mm graded aggregate (For Foundation) |
| 13 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in Hard/dense soil. |
| 14 | Removing excavated material in Hard/dense Soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point |
| 15 | M & L RCC- M-30 (Design Mix) using 20mm graded aggregate For Footing and plinth beams |
| 16 | M & L RCC- M30 (Design Mix) using 20mm graded aggregate for Column complete all as specified and directed |
| 17 | M & L RCC- M30 (Design Mix) using 20mm graded aggregate for beams and lintels complete all as specified and directed |
| 18 | M & L RCC- M30 (Design Mix) using 20mm graded aggregatefor RCC Slab |
| 19 | M & L RCC- M30 (Design Mix) using 20mm graded aggregatefor RCC parapet wall/drops/RCC Chajjas |
| 20 | S & F TMT bars 10mm dia & over of Grade Fe 500 incl cutting, bending, binding & placing in position with binding wirefor footings Slab beams roof slab etc complete al as specified and directed |
| 21 | Ditto as per item No 20 above but 5 to 10mm dia in stirrups, spacers & binders. |
| 22 | M & L Form workfor rough finished surfaces of concrete measured flat for For Footing |
| 23 | M & L Form workfor rough finished surfaces of concrete measured flat for Column, |
| 24 | M & L use & waste Form workfor rough finished surfaces of concrete measured flat for Plinth Beam |
| 25 | M & L use & waste Form workfor rough finished surfaces of concrete measured flat for RCCbeams sides and soffits |
| 26 | M & L use & waste Form workfor rough finished surfaces of concrete measured flat for RCCSlab |
| 27 | M & L use & waste Form workfor rough finished surfaces of concrete measured flat for RCCdrops/Chajjas |
| 28 | M & L Pre-cast cement concrete block masonry with solid blocks Type C1 1:3:6, exc. 10 cm in width and setting in Cement mortar (1:6) mortar, complete. |
| 29 | S& Ffactory made WPC solid door frames of size 65x100mm including fixing to walls using three numbers dash through bolt on each side as completeall asspecified .and directed |
| 30 | S& Ffactory made single extruded WPC solid door shutters decorative type flush door of size 35mm completeall asspecified and directed |
| 31 | S&F extruded aluminum alloy handles (150mm ) fabricated type anodised complete all as specified Make :- Shalimar / jyoti/ Classic/ Ashoka |
| 32 | S&F hinges (150 mm)stainless steel medium weight complete all as specified |
| 33 | S&F aluminum anodised barrel tower bolts (150 mm ) of extruded section complete all as specified |
| 34 | S&F 300 mmAluminium alloy , anodised , sliding door bolt with hasp, staple (bolt type ) and fixing clips of sheet , cast , exctruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified |
| 35 | S & F powder coated aluminium sections frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 36 | M&L for Ready mix plaster 10mm thickonfaces of bricks or concrete surface includingincluding preparation of wall surfaces etc complete all as specified and directed. |
| 37 | M&L for rendering 5mm thick in ready mix plaster on ceiling surface and finishing the surfaces even and smooth without using extra cement including scrapping down and preparation of ceiling surfaces to receive plaster, scaffolding as reqd etc, complete all as specified and directed. |
| 38 | M&L for Ready mix polimer modified cement based plaster 15mm thick on new bricks or concrete surface including preparation of wall surfaces etc complete all as specified and directed. |
| 39 | Material & Labour for applying two Coats Of Oil Bound Distemper Over One Coat Of Primer on Internal Wall |
| 40 | Material & Labour for applyingtwo Coats Of Oil Bound Distemper Over One Coat Of Primer on ceiling |
| 41 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additivesM @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 42 | M & L for hard core of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 10 cm thick watered and rammed to a true surface complete all as specified. |
| 43 | M & L 75mm thick Plinth Protection PCC (1:3:6) using 20mm graded aggregate (0.75 m wide). |
| 44 | M & L 75 mm thick Cement concrete type D-2 1:4:8 (40mm graded aggregate) as in Sub-Floors, Sub-Bases, Floors and pavings, etc all as specified and as directed. |
| 45 | Screed bed or bedding layer of mortar CM(1:6) 15 mm thick for laying floor finishes |
| 46 | M & L for coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 47 | M & L for Coloured Glazed ceramic tiles in vertical surface 350 x 250 mmx 7 mm / 450 x350x 7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 48 | M & L for machine cut kota stone slab flooring, 20mm thick over cement screed bas laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finish polishing all as specified and directed complete |
| 49 | All as per items No48 above but asin skirting complete all as specified and directed |
| 50 | M & L for granite work(table rubbed and polished) in jambs, steps, window cills, platforms and like in cement mortar 1:4 including pointing in white cemnt using marble dust with admixture of pigment to match with shade of granite 20mm thick,all as specified and directed complete |
| 51 | M & l for 3mm APP based polymeric membrane minimum weighing 3.5 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by torched application complete and finally finished as per manufacturers instructions |
| 52 | Screed bed or bedding layer of mortar CM(1:3) 10 mm thick |
| 53 | Supply only Water Proofing compound |
| 54 | S&Faluminum anodised grill DG- 202 ( 10 mm x 5.2mm ) of Deco grill or equivalent fixed with \"F\" section size not less than 20.60 x 15.20 x 1.5mm thick of approved make all as specified and directed.Note : (i)Make shall be of M/s Decogrille of M/s Associated Groups or equivalent as approved by the GE.(ii) Minimum thickness of anodizing shall be 15 microns. |
| 55 | Supply only 4mm thick sheet figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane etccomplete all as specified and directed |
| 56 | Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed. |
| 57 | S&F inGodrej night latch 4 lever for entrance door with fittings complete all as specified and directed |
| 58 | S&F brass chromium plated towel rail 20mm dia \"D\" type 600mm long between flanges, Cat No BA -01of with and including chromium plated brass screws etc complete all as specified and directed. Make:Prayag polymers Pvt Ltd or equivalent |
| 59 | S&F20mm dia fancy type chromium platedcurtain rod bracketscomplete all as specified and directed |
| 60 | S&F CI floor trap 75mm dia outlet, with CP grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) & taking down old trap complete all as specified and as directed. |
| 61 | S&F CI floor trap 100mm dia outlet, with CP grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) & including taking down old trap complete all as specified and as directed. |
| 62 | S&Fwash hand basin, vitreous china white of size550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar tapschromium plated fancy type etc complete all as specified and directed. |
| 63 | S&F for CP concealed stop cock 15mm borefancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 64 | S&FCP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 65 | S&FCP bib tap 15mm bore fancy type with crutch or butterfly handle, screwedfor iron pipe or for unions and fixed complete all as specified and directed. |
| 66 | S&FCP pillar taps15mm bore., cast copper alloy, chromium plated fancy type complete all as specified and directed. |
| 67 | M&L in repairwaste fitting of 32 mm borebrass, chromium plated for glazed ware wash basin etc complete all as specified and directed.. |
| 68 | S & F waste pipe for WHB/ sink32mm bore fixed to wash hand basin/sinks coupling length pipe 0.90 mtrs each Make -prayag complete all as specified and directed.. |
| 69 | S/Fin repair 15mm size PVC connection with PTMT nuts 450mm length.complete all as specified and directed. |
| 70 | S&F stainless steel grating in ground shape 100mm dia complete all as specified and directed. |
| 71 | S&F low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls or laid in floors etc. |
| 72 | S&F soap dish Cat No BA -25of Prayag polymers Pvt Ltd or equivalent complete all as specified and directed. |
| 73 | S&F 15mm bore U- PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings completed all as specifiec and directed. |
| 74 | Ditto all as per item No 73 above but 20 mm bore. |
| 75 | S&F for gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed of size 20mm bore complete all as specified and directed. |
| 76 | S & FSteel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1998 grade St.-240. |
| 77 | S & Frolled mild steel in roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing(Beam,tee, angle, channel or flat sections)incl distance pieces, cleats, etc conforming to grade Fe-410W-(Gde E-250 Quality A) |
| 78 | S & F for mild steel Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165. |
| 79 | S & F MS bands, straps, supports or stays for rainwater, ventilating pipes, including bolts if reqd, hooks(stay), hook and pintle hinges, large hasp and staples, clamps, hold fasts, wall ties, plain angle cleats for securing purlins to wood trusses or rafters and similar small articles confirming to Fe-290 Gde E-165 |
| 80 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with selftapping screws as specified. |
| 81 | S& F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of anycolour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 82 | Preparation of new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer. |
| 83 | S&F PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm dia |
| 84 | M&L synthetic Writing board with green or white colour surface fixed to walls including raised wooden boarders all as specified of size 4mx1.80m |
| 85 | Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in soft loose soil. |
| 86 | M & L Rendering 15 mm thick on fair faces of brick work or concrete surfaces using CM 1:4, finished the surface even and smooth all as specified and as directed. |
| 87 | M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade mixed with greay cement and pigment. |
| 88 | M & L for sand filling under floors or in foundations incl watering and consolidation complete all as specifed and directed. |
| 89 | M & L Reinforced concrete pipe class NP 2 laid and jointed complete with collars of 300 dia bore |
| 90 | M & Lconcrete bed to drain pipeof 300 dia bore using type C2 (1:3:6) |
| 91 | M & L for sand cushioning by spreading in trenches crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer -in-charge. |
| 92 | Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250 mm x 150 mm x 40 mm laid in trenches all as specified. |
| 93 | Supply and Layingor fixing or passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 16 Sqmm 4 core including necessary connection and providing cable lugs as required all as specified. |
| 94 | M&L for cutting existing road/hard and dence soil not exc 45 x 60 cm in wide & depth getting out excaveted materials for laying GI tube; returning filling & well rammin watering finish surface 10 cm from top using PCC 1:3:6 not less than 4 inch thick; including removal of surplas soil all as per directed. |
| 95 | S&F of HDPE pipe 50 mm dia, PN-10 for laying in ground, raod crossing etc for cable protection including necessary fittings, clamps for supports, etc complete all as specified and directed.. |
| 96 | S&F in repair/replacement of building Security lightfitting 30/35 Watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings completeall as per directed by Engr- in – charge. |
| 97 | S& F in replacement of GI steel tubing medium grade 40 mm dia and length up to 1.5 meter bent to shape of offset angle upto 45degree for fixing of security /street light fittings including MS clamps made of 32mm x5mm flat iron, nuts , bolts, etc all as directed by Engineer in charge |
| 98 | M&L for sub mainwiring with twosingle core1.5 Sqmm PVC insulated FRLS multistrandedflexible copperconductorcable 660/1100 volts grade down concealed in slab/wall through non metalic PVC conduitwith and includingPVC insulated 1.5 Sqmsinglecore singlestrand copperconductoras continous earth wire in greencolour connected to commonearth dolly complete all as specified and as directedNote : 1.Two runs ofcable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. |
| 99 | S & F MCCB TPNDB, 4 way TPN (vertical type), double door, 415 Voltsand including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete all as specified and directed.Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating.Make -Havells/Indoasaian/Legrand/ABB/Schnider |
| 100 | Supply & fixingMCCB 4 Pole,415 V, fixed type, 125 Amps with breaking capacity 16 KAincluding connecting up electrically with proper lugsglands and including all necessary fittings complete all as specified and directed. Make -Havells/Indoasaian/Legrand/ABB/Schnider |
| 101 | Supply and fixing TP 63 Amps rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 102 | Supply and fixing SP 63 Amps rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. Make -Havells/Indoasaian/Legrand/ABB/Schnider |
| 103 | -Ditto- all as per item No 102 above but for SP 40 Amps, 240V, 10KA \"C\" curve miniature circuit breaker (MCB) complete all as specified and directed. Make -Havells/Indoasaian/Legrand/ABB/Schnider |
| 104 | M & L for Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers all as shown in Electrical Plate No.3 connected to earthing test point all as specified or indicated including testing on completion. |
| 105 | M & L in repairs forpoint wiring with PVCinsulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductorcable 1.5 Sqmm drawn in and including PVC concealed conduit of suitable size of wall/ RCC slab/ ceiling/ colunms/ beams etc with all accessories, fittings, PVC junction boxes etc, with suitabe sunk pressed steel boxes for modular fittings not less than 1.6 mm thick, including Modular cover plate of suitable size etc with necessary fixing accessories andearth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 1.6 mm thick pressed steel terminal boxes concealed in wall mounting switches / sockets / fan regulators fixed with Cadmium platedmachine screws complete etc all as specified for one light / fan / bellpoint controlled by one switch. Note : 1.Two runs ofcable, one run of earth wire, one run of PVC conduit will be measured and paid one unit.Make of conduit :- Sudhakar/ Precision/ Diamond,Make of wire :- Finolex/ Havells/ Polycab/ KEI |
| 106 | -Ditto- all as per item No 105 above but for one 6A 2pin/3pin socket out let multipurpose on the same board with other switches. |
| 107 | -Ditto- all as per item No 105 above but for one 6A 2pin/3pin switch socket out let multipurpose on independent Board. |
| 108 | -Ditto- all as per item No 105 above but wiring complete with 2.5Sqmm for 3 pin 16A socket multipurpose on independent board |
| 109 | S & F in repairs modular type6A one way SP switch 1 moduleconfirming to IS: 3854-1997 with finger proof terminal complete all as specified and directed. |
| 110 | S & F in repairs modular type 2/3 pin 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed.Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree) |
| 111 | S & F in repairs modular type 2/3 pin 16 Amps socket 2 module conforming toIS: 1293-2005 complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree) |
| 112 | S & F in repairs modular type16 A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree) |
| 113 | S & F in repairs modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree) |
| 114 | S & F in repairs ceiling rose three terminal, 230 Volts PVC / Polycarbonate body, complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree) |
| 115 | S & F Modular Blank plate 1 module suitable for Modular switch boards all as specified and as directed |
| 116 | S & F Modularcover plate 12 modules complete all as specified and directed. |
| 117 | S & F Modularcover plate 8 modules complete all as specified and directed. |
| 118 | S & F Modularcover plate 6 modules complete all as specified and directed. |
| 119 | S & F Modularcover plate 4 modules complete all as specified and directed. |
| 120 | S & F Modularcover plate 3 modules complete all as specified and directed. |
| 121 | Supply & Fix LED batten fitting of capacity 20W, operating on 230V, 50Hz, AC Supply having luminous efficacy of not less than 100 lumens/watts, CCT 6500K, P.F>0.9, 2.5 KV surge protection, 4-feet long, housing made out of extruded aluminium housing with decorative end caps elegently designed complete all as specified. Make - Bajaj/ Wipro/ Jaquar/ Halonix |
| 122 | S & F 20W LED Batten with inbuilt smart motion sensor, 230 Volt, 50 Hz, 2 feet, polycarbonate extruded channel, powder coated with diffuser for glare free light, Inbuilt motion sensor prewired with 25% dimmer illuminous in ideal timewith all accessories including two Nos of PVC box of size 75x75x20mm for mounting light fittings including ceiling rose complete with following specification. (i) Housing -Polycarbonate extruded, diffuser-opal-polymer, LED MID power, Light distribution-general spread, LED efficiency - > 130 lumen/Watt, System effieciency- > 100 lumen/Watt, Driver efficiency - more than 85%, power factor- more than 0.95 to 0.98, THD - <10%, Mounting/Fixing- Wall/ Ceiling, Ingress Protection - IP-20, Sensor type- HF inbuilt integral occupancy/movement sensor, Sensor range- upto 5 mtrs(cone formation ), Dimming operation- default operation at 25% of the is rated value. On detection of motion, light output rises to 100% for upto 20 sec . in absence of motion switches back to default operation, LED life- upto 30,000 Hrs. Surge Protection - not less than 2KV. Note:- (i) contractor shall submit LM79 report LM 80Test certificates before claiming for payment .(ii) Warranty certificate for minimum 2 years to be submitted from OEM. Make: Bajaj/Polycab/Shakti/Jaquar/Crompton. |
| 123 | Supply and fixing ceiling fans complete with blades, down rods accessories etc operating with electronic regulator on 230 V, 1200 mm sweep. Min air delivery 210 CFM full load wattage 26 to 32 watts,High Speed conforming to IS 374 :2019, colour white BEE 5 star rated with brushless direct current motor (BLDC) without remote complete all as directed by Engr-in-Charge.Make : BAJAJ (Model : ENERGOS 28) / ORIENT (I FALCON) |
| 124 | S&F modular type 3/5 pin socket with one single pole MCB 20 Amp 230 Volts complete all as specified including concealing in wall suitable for Geyser, AC and Domestic appliances complete all as specified and directed. Make - Havells/ Legrand/ Schneider |
| 125 | Supply & fixing for sub mainwiring with twosingle core4.0 Sqmm PVC insulated FRLS multistrandedflexible copperconductorcable 660/1100 volts grade downin throughrigidflexiblewhere applicablenon metalicPVC casing capingwith and includingPVC insulated4.0 Sqmsinglecore singlestrand copperconductoras continous earth wire in greencolour connected to commonearth dolly all as specified and as directedincluding taking down of old sub main wiringNote : 1.Two runs ofSingle core cable, one run of earth wire & PVC Cassing Capping will be measured and paid one unit. Make - Havells/ Polycab/ KEI |
