|
| 1 | Dismantling asbestos cement (corrugated, semicorrugated etc) sheets in roof coverings complete all as specified and directed |
| 2 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ 150) as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed |
| 3 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ 150) as in roof covering/cladding to wall, ridge etc fixed with self tapping screws complete all as specified and directed |
| 4 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed |
| 5 | M&L for Non Skid colouredjoint free ceramic tiles 8-9mm thick(square/ rectangular) area of each tiles exc 0.18 Sqm but n. exc 0.38 Sqm (600x600mm) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 complete all as specified and directed |
| 6 | M&L for Non Skid colouredjoint free ceramic tiles 8-9mm thick(square/ rectangular) area of each tiles exc 0.18 Sqm but n. exc 0.38 Sqm (600x600mm) as in vertical surface such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 to recieve tiles complete all as specified and directed |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 8 | M&L for Non Skid coloured joint free ceramic tiles 7 to 8mm thick grade-4(square/ rectangular) area of each tiles exc 0.06 Sqm but n. exc 0.11 Sqm (300x300mm) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 complete all as specified and directed |
| 9 | M&L for coloured Glazed joint free ceramic tiles in vertical surfaces 350x250x7/450x350x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering or bedding layer of cement mortar 1:4 complete all as specified and directed |
| 10 | Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed |
| 11 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed |
| 12 | M&L for RCC 1:2:4 type B1 (using 20mm graded stone agg) as in slab and shelves supported on walls or Chajja/ Facia complete all as specified and directed |
| 13 | M&L form work to soffits of suspended slab such as roof slab and similar work n. exc 200mm thick (horizontal or sloping) rough finished flat surface complete all as specified and directed |
| 14 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 15 | M&L pre-polished Baroda green marble 14 -16 mm thick (table rubbed and polished) in step, jambs, pillars , window cills, cooking plateforms and the like in CM 1:4 incl pointing in white cement1:2 using marble dust with admixture of pigment to match with marble including half round moulding and making hole for gas pipe where required over 15mm thick screed bed in CM 1:6 complete all as specified and directed |
| 16 | Dismantling of wallandceilingboards(fibre, pulp, insulation etc) or insulationboards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed |
| 17 | M&L for GI snap grid framework including 4mm thick Designer E-boards for false ceiling (grid size 605mm x 605mm ) including necessary notching and preparing holes and hangers 2mm dia GI adjusting level fixed to structural members. Galvanised steel section of exposes T section grid with exposed flange faces dulypowder coated white/ivory colour. The suspension system consisting of perimeter wall angle of size 20x20x0.45mm of GS sheet to secured on wall/partition face with the help of rawl plug screws @450mm c/c.Universal T shaped main runner with single rotatary stiching of size 35x24mm made from 0.33mm thick GS sheet of length 3.60m to be spaced @1200mm c/c.Cross T shaped runner of size 25x24mm with double thick GS sheet 0.25mm thick spaced @ 600mm c/c.To form 600x600mm size module, intermediate T shaped cross runner of size 25x24mm made from 0.25mm thick GS sheetof length 600mm is placed inside the module of size 1200x600mmincluding suspension of the ceiling frame from structural members with 2mm thick GI wire and level adjusters all cut out etc to the required line and shape as per manufacturer recommendations complete all as specified and directed. |
| 18 | Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed |
| 19 | M&L for brick work with sub class \"B\" old size bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed |
| 20 | M&L for half brick work with subclass ‘B’ bricks, straight or curved on plan to any radius built in CM 1:4 complete all as specified and directed |
| 21 | M&L for 75mm thick PCC 1:3:6 type C2 (Using 40mm graded stone aggregate) as in plinth protection/path laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed |
| 22 | Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed |
| 23 | M&L for 15mm thick plaster in CM 1:6 on fair face of brick walls finished even and smooth without using extra cement complete all as specified |
| 24 | M&L for preparation of newly plastered surface of wall and applying two coats of internal acrylic distemper including a coat of primer of approved tint over a coat of wall care putty complete all as specified and directed |
| 25 | M&L for applying two coat of internal acrylic distemper of approved tint over a coat ofwall care putty on walls after complete removal of existing treatment and preparation of old plastered surface by rubbing down, washing complete all as specified and directed |
| 26 | M&L for 15mm thick plaster in CM 1:4 on fair face of brick walls finished even and smooth without using extra cement complete all as specified |
| 27 | Material & Labour preparing surfaces plastered or unplastered for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43litre/10sqmoverandincludingprimingcoat of exterior primer applied @ 0.90 litre/ 10sqm over new surfacescomplete all as specified and directed |
| 28 | Material & Labour preparing surfaces plastered or unplastered for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43litre/10sqmoverandincludingprimingcoat of exterior primer applied @ 0.90 litre/ 10sqm over Old surfacescomplete all as specified and directed |
| 29 | Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of sizeexc 1.5 Sqm and n.exc 4 Sqm complete all as specified and directed |
| 30 | Taking down chowkhats or frames area n. exc 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed |
| 31 | M&L (125mm X 63mm Double Rebate) Factory made 100% solid WPC Door frame made from 100% LEAD FREE (Single extruded process) material with density 780kg / Cum and manufactured by an ISO : 9001-2015 certified company, all as per specification drawings as directed by the Engr-in-Charge The door frame should be water proof, Termite proof, Fire retardant and having excellent, fixed with fasters with sufficient holding capacity complete all as specified and directed |
| 32 | M& L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 63X100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 33 | M& L Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 34 | M&L for 30mm thick brand factory made wire mesh solid WPC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 20mm x 40mm for stiles and 20mm x 40mm for top, lock & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacturer complete all as specified and directed. . |
| 35 | S&F in repair galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specifed and directed |
| 36 | S&Fwindows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM) and Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52x 25mm. Outer frame & mullion sections to have rebate for glazed shutters. Fly mesh with 20 mm GI flat beading for provision of guard bars/ grills. Fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stainless steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter with 0.36mm dia of wire and 1.40mm aperture. Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 12mm square guard bars with 110mm spacing c/c (Horizontal bay) to be welded on FI 20x6mm alaround except runner portion complete all as specified and directed |
| 37 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm both side prelam PVC sheet and edges will be painted to match with the prelam sheet reinforced with MS square tube in opening incl necessary fixing arrangements as per specification and drawing complete all as specified and directed |
| 38 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails.MS frame shall be covered with heat moulded prelam PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side prelam PVC sheetfor top rail, lock rail and bottom rail on either side as gap insert for top rails, bottom rail, panelling of both side prelam PVC sheet to be fitting in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement in the frame at site as per specification and drawing |
| 39 | S&F in repair Double layerrotational moulded PVC water storage tank cylinderical, vertical with closed top hoisted and fixed in position tank capacity 500 Ltr with and including PTMT float valve 20mm dia and making connection for inlet and outletcomplete all as specified and directed Make : Polycon/Rotomac/Sintex |
| 40 | S&F 250mm MS sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate |
| 41 | S&F 100mm size MS butt hinges medium weight ISI marked, cold rolled |
| 42 | S&F 200mm long MS barrel tower bolts all as specified |
| 43 | S&F 150mm size MS handles all as specified |
| 44 | S&F 150mm aluminium, anodised, barrel tower bolts of extruded section |
| 45 | S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised |
| 46 | S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete |
| 47 | S&F inrepair 100mm Pvc pipes single socketed in any length with rubber ring joint laid in trenches of floorcomplete all as specified and directed |
| 48 | S&F inrepair 75mm Pvc pipes single socketed in any length with rubber ring joint fixed to wallscomplete all as specified and directed |
| 49 | S&F PVC 75 mm floor trap plain with grating includingjointingwith solvent cement complete all as specified and directed |
| 50 | S&F PVC vent cowls 75mm |
| 51 | S&F in repair of sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm and bowl size 410mm x 330mm x160mm complete all as specified |
| 52 | S&F in repair vitreous china water closet Orissa pattern of size 580 X440mm white ISI marked including provn of cement concrete bedding including connections to flushing cistern/pipe and making good disturbed portion to match existing surfaces complete all as specified. |
| 53 | S&F in repair vitreous china white wash hand basin flat back of size 550x400mm including CI/MS brackets including cutting for and pinning in brackets but including waste pipe complete all as specified. |
| 54 | S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action push type with inlet ball valve and float including flush pipe long 32mm dia, ball valve, handle, bracket etc complete all as specified and directed. |
| 55 | S&F in repair 600x450x6mm thick looking mirror bevelled edge of selected quality glass fixed with stainless steel glass fastner complete all as specified |
| 56 | S&F in repair 15mm dia brass chromium plated Bib tap fancy type with wall flange complete all as specified |
| 57 | S&F in repair 15mm dia brass chromium plated pillar tap with fly nut with long swan neck screwed for 15mm bore dia of pipe complete all as specified |
| 58 | S&F in repair 15mm Stop valve angle cockfancy type, chromium plated with long shunk and cup (concealed type) high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified |
| 59 | S&F in repair chromium plated brass shower roses with or without swivel joints 125mm size including shower arm complete all as specified |
| 60 | S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer complete all as specified. |
| 61 | S&F in repair 32 mm dia PVC flush pipe of polyethylene of low or high density for WHB, sink, urinal complete all as specified and directed. |
| 62 | S&F in repair 20 mm dia brass CP tubular towel rail D type600mm long complete all as specified and directed |
| 63 | Taking up or down 15mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed |
| 64 | S&F 15 mm bore dia ofmedium grade galvanised steel tubing withall fittings including tank nipple and fixed complete to wall or laid in floor including cutting through walls, floors, etc and their making good with existing surface complete in all respect as specified |
| 65 | S&F 15mm boregun matel globe or gate valve with iron wheel, screwed both ends for iron pipes complete all as specified |
| 66 | Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed |
| 67 | S&F 20 mm bore dia ofmedium grade galvanised steel tubing with all fittings including tank nipple and fixed complete to wall or laid in floor including cutting through walls, floors, etc and their making good with existing surface complete in all respect as specified |
| 68 | S&F 20mm boregun matel globe or gate valve with iron wheel, screwed both ends for iron pipes complete all as specified |
| 69 | S&F in repair of 20mm dia SS drapery rod, fancy type, SS knobs and brackets, fixed in any length complete all as specified and directed |
| 70 | M&L for 75mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in path finish the top surfaces even and rough to receive top layer complete all as specified and directed |
| 71 | M&L for rubber moulded coloured glossy finish cement concrete chequered tiles of size 20cm X 20cm X 25mm thick jointed in neat cement slurry and pointed in white or coloured cement and pigment to match the surface of tile as in floor over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed |
| 72 | M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping, edging including necessary form work complete all as specified |
| 73 | M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in surface channel or drain or benching in manhole complete all as specified and directed |
| 74 | M&L for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/stoppedends etc complete all as specified and directed |
| 75 | S&F in repair 18 mm thick with min density 600 Kg/Cum LEAD FREE PVC Celuka ply of one sideand other side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed |
| 76 | S&F 150mm Hasp and staple, SS steel, wire type, including bolt to hinge plate and fixed with screws all as specified and as directed |
| 77 | S&Fauto closing hinge , mild steel, bright finished or electro galvanized, width of flaps (When open) 30mm |
| 78 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed |
| 79 | S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces,Stragingetc complete, drilled for fixing of steel sheeting or other coveringdoors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittingsand hanging, also fastening and fixing conforming to Fe 410-W (Gde-E-250) quality \"A\" complete all as specified and as directed by Engr-in-Charge |
| 80 | M&L for applying two coat of synthetic enamel paint on steel surfaces inc primer of any description over 10cm width or girth not otherwise described and complete all as specified and directed by Engr-in-Charge |
| 81 | S&F welded steel wire fabric weight n. exc 4 Kg per Sqm suitable to weld with steel members complete all as specified and directed by Engr-in-Charge |
| 82 | Disconnecting the electrification and taking down DBs (any type of SPN DBs) andmaking good to the disturbed surfaces to match the existing surface all as specified and as directed by EIC.Note - Temporary power supply shall be provided by contractor. |
| 83 | Taking down U/S submainwiring aluminiumetc and making good the disturbed surfaces of walls/ floor etc matching with the existing surface. |
| 84 | M&L for sub-main wiring (concealed) with two single core 6 sq mm FRLSH PVC insulated unsheathed stranded copper conductor cable drawn through including chasing cutting in any type of massinory including 25 mm dia non-metallic PVC conduit fixed in wall including 6 sq mm copper earth continuity wire, accessories and connecting to earth dolly complete, all as specified and as directed by EIC. |
| 85 | Taking down carefully aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pedants, regulators, sockets, light fitting etc.. and making good the disturbed surfaces of walls/ floor etc matching with the existing surface all as specified and as directed by EIC. |
| 86 | Material & Labour for following type Point Wiring controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and includingconcealedPVC conduitMMS ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia(Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates). |
| 87 | One light point controlled by one switch. |
| 88 | One ceiling fan pointcontrolled by one switch. |
| 89 | One exhaust fan pointcontrolled by one switch. |
| 90 | One 3 pin socket outlet 5 Amps on the same board. |
| 91 | One 3 pin socket out let 5 Amps on the independent board. |
| 92 | One bell point controlled by one bell push |
| 93 | All as per Item No.86 above but 2.5 Sq mm multi stranded copper conductor with 2.5 Sq mm copper earth continuity wire connected to earth duly complete for one 15A Socket on Independent board all as specified and as directed by EIC. |
| 94 | Supply and fixing surface & wall mountedLED batten 4 feet with 1x20 Watt indoor decorative luminaries with and including electronic driver and 1x20 watt LED Lamp, pre-wired including necessary electric connection with copper flexible PVC cable of 0.50 Sq mm 3 core not more than 1 mtr in length from ceiling rose/connector to light fitting,conforming to the following specifications: (i) System Watts/lumens: - Max 20 W/Total system lumen not less than 2400 Lm, voltage range- 140 to 270 Volts, continious operation of 2 hours at 320 Volts.(ii) Housing: - Aluminium Extruded body. (iii) IP rating: - Minimum IP 20. (iv) Front cover: - Acrylic/polycarbonate cover (v) Mounting: - Suitable for wall/ ceiling mounting. (vi) Finish: - Smooth finish. (vii) Lamp: - High bright LED. (viii) System Efficacy of Luminaries (lm/Watt): - Not less than 120 Lm/watt. (ix) Colour temperature: - Not less than 5700 degree K. (x) Colour rendering index (CRI): - Not less than 80. (xi) Life: - Not less than 25000 hrs of operation. (xii) Optics: - Designed for optimum light distribution. (xiii) Control gear: - Inbuilt electronic driver with APFC, PF not less than 0.95, and THD not more than 20% of the standard operating voltage 180-270V Ac, 50 Hz. (xiv) Surge protection: - Inbuilt surge protection minimum 2.5 KV. (xv) Heat sink: - As per OEM\"s design. |
| 95 | S & F anglelamp holder, PVC Polycab type with back plate suitable for batten fittings complete including fixing of 9/10 watt LED bulb all as specified. |
| 96 | Supply and fixingstep socket type modular fan regulator 120/280 V , 100Watt all as specified and as directed. |
| 97 | Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge. |
| 98 | S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge. |
| 99 | Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge. |
| 100 | Supply and fixing switch modular , one-way 16Amps,1 module 240 Volts AC all as specified and directed by Engr- in-charge. |
| 101 | S & F Switch Modular bell push single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge. |
| 102 | Supply and fixing door bell ding dong type suitable for 230 Volts, AC, 230 Volts, single pole. |
| 103 | M & L for ceiling rose, surface bakelite, 65 x 50 mm, three terminals all as specified and as directed. |
| 104 | S & F sheet metal enclosures for SPN DB\"s with double glazed door for incorporating MCBs,IP-43 , 8 way with 200 amps rated busbar, 240 volts, as per IS-8623 all as specified and as directed. |
| 105 | S & F MCBs SPN 32 amps, 240 volts, 50 Hz, \"C\" curve including necessary incoming and out going electric connection with suitable size of copper lugs all as specified and as directed by Engr-in-Charge. |
| 106 | S & F MCB SP, 6 to 32Amps,240 volts, 50 Hz, \"C\" curveincluding necessary incoming and out going electric connection with suitable size of copper lugs all as specified and as directed by Engr-in-Charge. |
| 107 | M & L for Earthing complete with galvanised steel pipe electrode, 600 x 600 x 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 mtrs deep below nominal ground level) with top edge of the plate not less than not less than 1.5 metres below nominal ground level connected to galvanised earthing lead of 4 mm dia of iron or steel wire all as shown in electrical plate No. 5 all as specified and as directed.Note :- the cost of excavation and earth work PCC pit and CI cover funnel & watering pipe, wiremesh, charcoal dust and common salt shall be deemed included in the unit rate for earthing all as specified and as directed by EIC. |
| 108 | Taking down old unserviceable existing service/UG cable all as specified and as directed by EIC. |
| 109 | Material and labour for XLPE insulated,LT armoured electric cable with aluminium standed conductor 1100 volts grade,cross-sectional area 35 sqmm ,3.5 core laid in trenches/pipes/ducts/wall/boarings with necessary cable lugs and glands,nuts,bolts and washers etc and testing complete all as specified and directed. |
| 110 | Excavation in trenches not exceeding 1.5 mtr wide and not exc 1.5 mtr depth for laying of cables, pipe lines, protection pipes and foundations etc and getting out in soft loose soil complete all asspecified and directed. |
| 111 | Returning filling in soil including spreading leveling watering and well rammimg in layer n exc 25 cm complete all as specified and directed |
| 112 | Removing excavated soil not exc50 mtr ant depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed |
| 113 | M & L for brick sub class \"B\" 250mm x 115mm x 0.75mm and laid in trenches as in protection of UG cablecomplete all as specified and directed. |
| 114 | Supply and filling in and speading unwashed river sand for cushioning and covering the under ground cables in trenches and punning to provide required cover complete all as specified in SSR Part-I and as directed. |
| 115 | M & L for 50mm bore GI pipe (Light grade) laid under road or fixed with pole/wall of culvert as in protection of UG cableincl necessary MS clamp and complete all as specified and directed. |
| 116 | Boaring holes horizontally under Road without damaging the surface of road (minimum 1.0 Mtr bellow the road surface) with the help of GI tubing of any dia not exc 100 mm dia for passing of UG cable all as specified and as directed.(GI Pipe laid shall be measured seperately) |
| 117 | Supply, fabricated and and fixing of street light bracket made out of GI pipe 1.0 Mtr long, 32mm dia medium grade bent to shape as directed including clamps made out of 40 mm x 6 mm flat for fixing bracket suitable for steel tubular poles including nuts and bolts, washers and other connected items of required size including painting with one coat of aluminium paint over a coat of red oxide/primer all as specified and as directed. |
| 118 | M & L for LED Bldg Security light Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. |
| 119 | M & L for disconnecting electric supply, taking down fan, cealing cable ends, dismantling blades carefully after unscrewing nuts and bolts of ceiling fan any size from existing position and bringing to AGE E/M store yardall as specified and as directed by EIC. |
| 120 | M & L for 40mm bore GI pipe (med grade) laid or fixed with wall for hanging of ceiling fan of 1200 mm sweep including necessary PCC work andMS clamp suitable for fancomplete all as specified and directed. |
| 121 | S & Fvertical load line in sheet metal enclosures MCCB TPN DB\"s with double door for incorporating MCCB as incomer and MCBs SP/SPN as outgooing , IP-43 , TPN 4 way with 200 amps rated busbar, 440 volts, as per IS-8623 including taking out old UNSV DB and making good the disturbed surface of wall and match with the existing surface compelte all as specified and as directed. ( Note- MCCB 3 pole 63 amps as main incomer will be included in quoted rate) |
| 122 | NOTES :-1.For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed. |
