Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.Up to 1.50 mt depth |
| 2 | Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. above 1.50 mt Up to 3.00 mt depth |
| 3 | above 3.00 mt Up to 4.50 mt depth |
| 4 | above 4.50 mt Up to 6.00 mt depth |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50and lift upto 1.5 m. |
| 6 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 7 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 8 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. |
| 9 | Providing and injecting chemical emulsion for pre-constructional anti termite treatment and creating andchemical barrier under and around the coloumn pitswall, trenches, basement, excavation top surface of plinth filling junction of wall and floor along the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete (plinth area of the building at the ground floor only shall be measured as per SI 6313 (part-II 1981) Alderine emulsiifiable concentrate or any other approved material such as Heptrachlor or Chlordane will be used. the rate ofapplication 5 lit./per sqm of chemical emulsion shall be asfollows-1 Treatment for masonary and foundation 5 Ltr per sqm.2- Back fill in immediate contact with foundation 7.50 Ltr per sqm. 3- Treatment of top surface of plinth filling 5 Ltr per sqm. 4- Treatment junction of wall and the floor 7.5 Ltr per sqm.5- Treatment of soil along external perimeter of building 7.5 Ltr per sqm.6- Treatment of soil under apron along external perimeter 5 Ltr per sqm. (As per manufacturer\"s standard dilution). |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth. 1:4:8 (1 Cement : 4 coarse sand (ZONE-III) derived from natural sources : 8 graded stoneaggregate 40 mm nominal size derived from natural sources). |
| 11 | Providing and laying damp-proof course 40mm thick with cementconcrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from naturalsources : 4 graded stone aggregate 12.5mm nominal size derived fromnatural sources) |
| 12 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 13 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). |
| 14 | Centring and shuttering including strutting, propping etc. and removal of form for :Foundation, Footing base of column etc. |
| 15 | Suspended floors, roofs, landings, balconies and accessplatform |
| 16 | Lintels,plinth beam& Beams |
| 17 | In Column\"s |
| 18 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 19 | Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safeworking load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap):300 mm dia piles |
| 20 | Brick work with common burnt clay F.P.S. (non modular) bricks of class 150in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 21 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 22 | Brick work with Class-150 bricksconforming to IS: 2222 -1991 in superstructure above plinth level upto floor five level in all shapes and sizes: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 23 | Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 150 in foundations and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 24 | Half brick masonry with F.P.S. (non modular)bricks of class designation 150 in superstructure above plinth level upto floor V level: Cement mortar 1:4 (1 cement :4 coarse sand) |
| 25 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 26 | Providing filling cinder in sunken portion |
| 27 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting offollowing operations:a) Applying a slurry coat of neat cement using 2.75 kg/sum. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120mm and minimumthickness at khurra as65 mm. |
| 28 | Providing wood work in frames of doors, windows, clerestory windowsand other frames, wrought framed and fixed in position with hold fastlugs or with dash fasteners of required dia & length (hold fast lugs ordash fastener shall be paid for separately): Second class teak wood |
| 29 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 30 | Extra for cutting rebate in flush door shutters (Total area of the shutterto be measured). |
| 31 | UPVCWINDOW: Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) |
| 32 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 33 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. |
| 34 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 35 | 12 mm cement plaster on the fair side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand) |
| 36 | 12 mm cement plaster on the fair side of single or half brick wall of mix : 1:6 (1 cement : 6 coarse sand) |
| 37 | 15 mm cement plaster on rough side of single or half brick wall of mix : 1:6 (1 cement : 6 coarse sand) |
| 38 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floatingcoat of neat cement: 20 mm cement plaster |
| 39 | 6 mm cement plaster 1:3 (1 cement : 3 course sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams. |
| 40 | Add for plaster drip course/ groove in plastered surface or moulding toR.C.C. projections. |
| 41 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate |
| 42 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 43 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm |
| 44 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanitywindow sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqm |
| 45 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Light shade pigment using white cement |
| 46 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cementmortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 47 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 48 | Providing and laying rectified Glazed Ceramic Wall tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @3.3 kg/sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 49 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thicknessto be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4(1 Cement : 4 Coarse sand), jointing with grey cement slurry @3.3 kg/sqm including pointing the joints with whitecement and matching pigments etc., complete. |
| 50 | Finishing with Deluxe Multi Surface Paint system for interiors and exteriors using primer as per manufacturers specification: Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture |
| 51 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sum. over and including priming coat of exterior paint applied @ 0.90 litre/10 sqm. |
| 52 | Distempering with 1st quality acrylic distemper (ready mixded) having VOC content less than 50 gram/litre, of approved manufacture and of required shade and colour all complete to achieveeven shade and colour : New work (two or more coats) over and including waterthinnable priming coat with cement primer having VOC content less than 50 gram/litre. |
| 53 | Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 54 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 55 | Providing and fixing chromium plated brass curtain rod having wall thickness 1.25mmwith two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc. wherever necessary complete: 25 mm dia. |
| 56 | Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge: With decorative veneering on one side and commercial veneering on other side |
| 57 | Providing and fixing wall panelling comprising of wooden frame wrok using 50mmX50mm sections ofhard/sal wood in a maximum spacing of 600mm c/c on both side. (fixing of membersas required) covered with 12mm thick plywood layered with 4 mmthick veneer on one side pasted and pressed with adhesive to give a comfort & smooth finish. PU polish etc complete |
| 58 | Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge: With 20 mm thick beveled tegular mineral fibre falseceiling tile (NRC 0.7) |
| 59 | Providing and fixing Stainless Steel sliding door bolts, approved quality & make with necessary screws etc all complete: 250x10 mm. |
| 60 | Providing and fixing Stainless Steel tower bolts, approved quality & make with necessary screws etc all complete: 250x10 mm |
| 61 | Providing and fixing Stainless Steel tower bolts, approved quality & make with necessary screws etc all complete: 200x10 mm |
| 62 | Providing and fixing Stainless Steel handles, approved quality & make with necessary screws etc all complete. : 125 mm. |
| 63 | Providingandfixing150mmbrightfinishedfloorbrassdoor stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete |
| 64 | Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with : 5.5 mm thick glass panes |
| 65 | Salt Peter Treatment: Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 66 | Cement plaster 1:4 (1 cement: 4 coarse sand) finished with a floatingcoat of neat cement: 15 mm cement plaster |
| 67 | Providing & applying a coat of residual petroleum bitumen of grade ofVG-10 of approved quality using 1.7kg per square metre on damp proofcourse after cleaning the surface with brushes and finally with apieceof cloth lightly soaked in kerosene oil. |
| 68 | Supply & Fixing of Polythene Sheet 50 micron |
| 69 | SANITARY INSTALLATIONS & C.P FITTINGS: Providing and fixing water closet squatting pan ( Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS:7231,with all fittings and fixtures complete including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. |
| 70 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI markedwhite solidplastic seat and lid |
| 71 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: a)White Vitreous China Wash flat back basin size 550x400 mm with single 15 mm C.P. brass pillar tap |
| 72 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : one urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 73 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board, 510x1040 mm bowl depth 250 mm |
| 74 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete: Flexible pipe, (a).32 mm dia (for wash basin) |
| 75 | (b).40 mm dia(for sink and urinal) |
| 76 | Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 77 | CP Brass fittings: Providing and fixing unplasticised PVC connection pipe with brass unions: 45 cm length, 15 mm nominal bore |
| 78 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931.a) 15 mm nominal bore |
| 79 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards andweighing not less than 690 gms.a) 15 mm nominal bore |
| 80 | Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931.a) 15 mm nominal bore |
| 81 | Providing and fixing C.P. brass shower rose with 15 or 20mm inlet, 150 mm diameter |
| 82 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931: 15mm nominal bore |
| 83 | Providing and fixing 8 mm dia C.P. /S.S .Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopeantype W.C. of quality and make as approved by Engineer - in - charge |
| 84 | Providing andfixing CPBrass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 85 | Providing and fixing toilet paper holder: C.P. Brass |
| 86 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc.,complete |
| 87 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms. |
| 88 | Providing & fixingC.P. towel ring round shape 250 mm dia with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality. |
| 89 | Providing and fixing 600 mm long C.P. towel rail complete with brackets fixed wooden cleats with CP brass screws with concealed fittings arrangement of approved quality. |
| 90 | INTERNAL & EXTERNAL WATER SUPPLY WORKS: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 20mm nominal dia pipes |
| 91 | 25mm nominal dia pipes |
| 92 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall : 15mm dianominal bore |
| 93 | 20mm dianominal bore |
| 94 | 25mm dia nominal bore |
| 95 | 32mm dia nominal bore |
| 96 | 40mm dia nominal bore |
| 97 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work: 40 mm dia nominal bore |
| 98 | 50 mm dia nominal bore |
| 99 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25mm dia nominal bore |
| 100 | 32mm dia nominal bore |
| 101 | 40mm dia nominal bore |
| 102 | 50mm dia nominal bore |
| 103 | Providing and fixing brass stop cock of approved quality:20 mm nominal bore |
| 104 | Constructing masonry Chamber 60x60x75 cm inside, in brick work of class designation 150 in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 600X600X750 |
| 105 | Extra for depth formanholes. |
| 106 | Providing & fixing Rain water pipe: Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 of working pressure 6 kg/sqmincluding jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion: 110 mm dia |
| 107 | Providing and fixing on wall face unplasticised PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion: Coupler: 110 mm |
| 108 | Bend 87.5 degree: 110 mm Bend |
| 109 | Shoe (Plain): 110 mm Shoe |
| 110 | Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with MS screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete: 110 mm |
| 111 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete. |
| 112 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank |
| 113 | SEWERAGE SYSTEM : Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m: All kinds of soil: Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm. (For external sewarage) |
| 114 | Supply and fixing of UPVC S.W.R. pipe type -B confirming to IS- 13592 including jointing the pipes with rubber ring, lubricant and UPVC SWR cuplar confirming to IS - 14735. Also including excavation of trenches cutting of walls and holes and repairing the walls floors and refilling the trenches as before but excluding supply and cost of other fittings such as elbow, bead, tee and Y-tee including supply of all material labour and T&P .Required for proper completion of the work: (i) 75 mm O.D. |
| 115 | (ii) 110 mm O.D. |
| 116 | Providing and fixing unplasticised -PVC pipe clips of approved designto unplasticised - PVC rain water pipes by means of 50x50x50 mmhard wood plugs, screwed with M.S. screws of required length,including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete: 75 mm |
| 117 | 110 mm |
| 118 | Supply and fixing of UPVC S.W.R. door bend confirming to IS- 14735: (i)75 mm size |
| 119 | (iii)110 mm size |
| 120 | Supply and fixing of UPVC S.W.R. Plain bend confirming to IS- 14735: (i)75 mm size |
| 121 | (iii)110 mm size |
| 122 | Supply and fixing of UPVC S.W.R. Plain Tee confirming to IS- 14735: (i)75x75x75 mm |
| 123 | (iii)110x110x110 mm |
| 124 | Supply and fixing of UPVC S.W.R. Door Y confirming to IS- 14735: (i)75 mm size |
| 125 | (iii)110 mm size |
| 126 | Supply and fixing of UPVC S.W.R. Cowel confirming to IS- 14735: (iii)110 mm size |
| 127 | Supply and fixin g of UPVC S.W.R. Nahni trap size 100/75mm, 100/90mm confirming to IS - 14735 self cleannig design fixed in PCC 1:2:4 and supply and fixing of 125mm dia heavy duty CP brass jali. |
| 128 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete: 100mm diameter |
| 129 | 150mm diameter |
| 130 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all roundS.W./UPVC pipes including bed concrete as per standard design: 100mm dia SW pipe |
| 131 | 150mm dia SW pipe |
| 132 | 150mm dia SW/UPVC pipe (for RWH) |
| 133 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type: With common burnt clay F.P.S. (non modular) bricks of class designation 150. |
| 134 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). With common burnt clay F.P.S. (non modular) bricks of class designation 150. |
| 135 | Extra for depth for manholes: Size 90x80cm with With common burnt clay F.P.S. (non modular) bricks of class designation 150 |
| 136 | Providing and fixing in position pre-cast R.C.C. manhole cover andframe of required shape and approved quality: EHD - 35: Circular shape 560 mm internal dia |
| 137 | Making soak pit 2.5 m diameter 3.0 m deep ith 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter 1.8 m long complete as per standerd design: With common burnt clay FPS (non modular) bricks of class designation 150. |
| 138 | POINT WIRING: Wiring for light point/fan point/ exhaust fan/call bell point with 1.5 sqmm. FRLSH PVC insulated copper conductor single core cable in Surface/ recessed medium class PVC conduit, , with modular switch, modular plate, suitable G.I. box and earthing the point with 1.5sqmm FRLSH PVC insulated copper conductor single core cable etc as required: Group B |
| 139 | Wiring for twin control light point with 1.5 sqmm. FRLSH PVC insulated copper cunductor single core cable in Surface/ recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable size G.I.box and earthing the point with 1.5sqmm FRLSH PVC insulated copper conductor single core cable etc. as required. |
| 140 | Supply and fixing of suitable size GI box with modular plate and cover in front on surface or inrecess, including providing and fixing 3 pin 5/6 amps. modularsocket outlet and 5/6 amps. modular switch, connection, painting etc. as required. |
| 141 | Supply and fixing of suitable size GI box with modular plate and cover in front on surface or inrecess, including providing and fixing 6 pin 15/16 & 5/6 amps. modularsocket outlet and 15/16 amps. modular switch, connection, painting etc. as required. |
| 142 | Supply and fixing 20 amp, 240 volts, SPN industrial Type, socket outlet ,With 2 pole and earth ,metalenclosed plug top along wth 20 amp. `C` curve SP,MCB , in sheet steel encosure, on surface or in recess with chained metal cover for the socket out letand complete with connections, testing and commissioning etc. as required. |
| 143 | Supply and fixing of two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 144 | Wiring for circuit/sub-main wiring along with earth wire with the following sizes of FRLSH PVC insulated copper conductor, single core cable in surface/ recessed medium class PVCconduit as required. 2X1.5 sqmm + 1x1.5 sqmm earth wire |
| 145 | 2X2.5 sqmm + 1x 2.5 sqmm earth wire |
| 146 | 2X4.0 sqmm + 1x 4.0 sqmm earth wire |
| 147 | 2X6.0 sqmm + 1x 6.0 sqmm earth wire |
| 148 | 2X10.0 sqmm + 1x 6.0 sqmm earth wire |
| 149 | DISTRIBUTION BOARDS, MCB\"S & ISOLATORS : Supplying and fixing followingway, prewired SP&N MCB distribution board of sheet steel for 240 volts on surface /recess completewithloose wire box, terminal connection for all incoming and outgoing circuit,duly prewired with suitable size FRLSH PVC insulated copper conductor up to terminal block, tinned copper busbar, neutral link, earth bar, din bar,detachable gland plate, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators):6 way , Double door |
| 150 | Supplying and fixing followingway, prewired three pole and neutral MCB distribution board of sheet steel for 415 volts on surface /recess completewithloose wire box, terminal connection for all incoming and outgoing circuit,duly prewired with suitable size FRLSH PVC insulated copper conductor up to terminal block, tinned copper busbar, neutral link, earth bar, din bar,detachable gland plate, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators):6 way (4 + 18), Double door |
| 151 | Supplying and fixing 5 amps. to 32 amps. rating, 240/415 volts, 10kA, `C\" series,miniature circuit breaker (MCB) suitable for inductive load offollowingpolesin the existingMCBDBcomplete with connections, testing andcommissioning etc. as required:Single Pole |
| 152 | Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required. |
| 153 | Supplying and fixingfollowingrating, four pole, (three phaseand neutral) 415volts,residual currentcircuit breaker (RCCB), havingasensivity current upto 30 mA in the existing MCB DB complete with connections,testing and commissioning etc. as required : 63 Amps |
| 154 | EARTHING: Earthing with GI earth pipe, 4.5mtr long, 40mm dia including accessories and providing masonary enclosure withcover platehavinglockingarrangement and watering pipe etc, (with charcoal/coke and salt ) as required.(For internal electrification) |
| 155 | EARTHING: Earthing with GI earth pipe, 4.5mtr long, 40mm dia including accessories and providing masonary enclosure withcover platehavinglockingarrangement and watering pipe etc, (with charcoal/coke and salt ) as required: (For external lighting) |
| 156 | Supplying and Laying of 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with G.I. nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm): (For internal electrification) |
| 157 | Supplying and Laying of 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with G.I. nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm): (For external lighting) |
| 158 | Providing and Laying earth connection from earth electrode with 6 SWG dia G.I wire in 15 mm dia G.I. pipe from earth electrode, including connection / terminating with G.I. thimble excavation and re-filling etc. as required: (For internal electrification) |
| 159 | Providing and Laying earth connection from earth electrode with 6 SWG dia G.I wire in 15 mm dia G.I. pipe from earth electrode, including connection / terminating with G.I. thimble excavation and re-filling etc. as required: (For external lighting) |
| 160 | INSTALLATION OF LIGHT FIXTURES : Installation, testing and commissioning of prewired, flourescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling / wall, including connection with 1.5 sq. mm. FRLSH PVC insulated, copper conductor, single core cable etc. as required. |
| 161 | Installation of exhaust fanin the existing opening, including making good the damage, connections, testing, commissioning etc. as required: upto 450 mm sweep |
| 162 | Extra for fixing the louvers / shutters complete with frame for a exhaust fans of all sizes. |
| 163 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required: Upto 35 sq.mm |
| 164 | Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required: Upto 35 sq.mm |
| 165 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 166 | Supply andlayingofaluminiumconductor PVC. insulated armoured,served,sheathed cable 1100volts gradeat 750mmbelow ground level overacushion of 75 mm thick sand around & protected with brick onsides & top on surfacethecablerunshallbe fixed on M.S. clamps etc. of suitablesize completeinallrespect. The armouring of the cable shall be properlyconnectedwith the earth conductor by clamps etc: 16 sqmm4core |
| 167 | 120 sqmm3.5core |
| 168 | for 400 watt hpsv lamp: 6sqmm 2 core |
| 169 | 10sqmm 2 core |
| 170 | 10sqmm 4 core |
| 171 | 25sqmm 3.5 core |
| 172 | Supply of AC 230/250 Volts, 50 Hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required-Make: USHA Cat No. TURBO JET DLX: 300mm sweep. |
| 173 | SUPPLY OF 6 to 10 Watt , LED Down Lighter Make- Havells INTEGRANXTRDDLRSURD9WLED865S |
| 174 | S/F OF 2x2 36W Down Light Make- Wipro CRCO10R036HE57G3 |
| 175 | SUPPLY OF 40W TUBE LIGHT STOUTPLUS1200BS40WLED857SPCWH: a) 1x40 Watt. |
| 176 | S/FOF 10W Mirror Light Make: ENDURALINEARNEOBS10WLED865SPCWH |
| 177 | PANNEL: Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete with all respects. The instrument chamber shall be separate and shall comprise of plug type ammetre, voltmetre, selector switches for ammetre and voltmetre instrument, fuses current transformer etc. the board shall have suitable capacity electrolytic Aluminium busbars as per IS : 8623 insulated with heat shrink sleevings and mounted on non hygroscopic supports such as CMC/DMC supports with detachable side cover and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entry boxes in case of pedestal type, cable sockets compression glands and indicating lamp for incoming etc. The job include the grounting of the board as per direction of Engineer in charge. All outgoing switches of 100 Amp and above will be provided with Amp Metre, current transformers and selector switches etc. and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm /2mm cubicle type switch board shall be of cat. A. B. & B -II and pdestal type for cat.- B and C only. a) Incoming: 630 Amp. TPN -1 No.Outgoing:100amp TPN-5 Nos & 32 Amp. TPN -1 Nos. Cat.B- Cubicaltype |
| 178 | FIRE EXTINGUISHER : Supply and fixing of fire extinguiser ,ABC Type 4.0 kg capacity (ISI Marked IS : 15683 & TAC approved (complete with initial charge and wall bracket ,along with supply of all materials and labour for proper completion of work |
| 179 | Supply and fixing of fire extinguiser ,CO2 Type 4.5 kg capacity (ISI Marked IS : 2878 & TAC approved (complete with initial charge and wall bracket ,along with supply of all materials and labour for proper completion of work. |
| 180 | Supply and fixing of fire bucket, round bottom made of G.I. sheet 9-11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-Charge. |
| 181 | FIRE DETECTION AND ALARM SYSTEM: Supplying, installation, testing & commissioning of manual callboxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. |
| 182 | Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in A.B.S. box with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. |
| 183 | ASPIRATION DETECTOR ACCESSORIES: CABLING & WIRING:Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required. |
| 184 | Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required: speaker cable Single pair, 2-core, 1.5 sqmm |
| 185 | WET RISER SYSTEM : Internal Hydrant System: Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel cuopling of 63 mm dia with cast iron wheel ISI marked confirming to IS 5290 (Type-A) with blank Gunmetal/Stainless Steel cap and Chain as required: Single headed Stainless Steel |
| 186 | Supplying and fixing 63 mm dia 15 m long RRL hose pipe with 63 mm dia male and female coupling duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required: Stainless Steel (Grade 304) |
| 187 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings the pipe on the wall/ceiling with suitable clamps/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 100mm dia |
| 188 | Supply and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type-2 as per IS: 12585 20 mm nominal internal dia gun metal glove valve & nozzle. Drum and brackets for fixing the equipments on wall. Connection from riser with 25 mm dia stop gun metal valve 7 M.S. pipe and socket: 30 m |
| 189 | Supply and fixing air vessel made of 250 mm dia , 8 mm thick M.S. sheet 1200 mm height with air release wall ontop and flanged to connection to riser , and drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with senthtic enamel paint of approved shade and required |
| 190 | Providing, Installation, Testing & Commissioning of Non-Return Valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required: 100 mm |
| 191 | Supply, fixing, testing and commissioning of double flanged Sluice Valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required: 40 mm |
| 192 | 100 mm |
| 193 | Supply, fixing, testing and commissioning of butterfly Valve of rating PN 1.6 with bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 13095 of following sizes as required: 100 mm |
| 194 | Supply and fixing of the fire brigade connection of cast iron body with gun metal male instaneous inlet coupling compete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia MS Pipe |
| 195 | (A) Supplying, installation, testing and commissioning of electic driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump). (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS: 1520. (C ) Suitable HP squirell cage induction motor TEFC Type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horizontal foot mounted type with Class-\"F\" insulation, confirming to IS: 325. (D) M.S. fabricated common base plate, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. Discharge :450 liter per minute at 35 m Head |
| 196 | Construction of granular sub-base by providing close graded Materialconforming to specifications, mixing in a mechanical mix plant atOMC, carriage of mixed material by tippers to work site, for all leads& lifts, spreading in uniform layers of specified thickness with motorgrader on prepared surface and compacting with vibratory power rollerto achieve the desired density, complete as per specifications anddirections of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 |
| 197 | Providing and laying C.C. pavement of mix M-25 with ready mixedconcrete from batching plant. The ready mixed concrete shall belaid and finished with screed board vibrator , vacuum dewateringprocess and finally finished by floating, brooming with wire brushetc. complete as per specifications and directions of Engineer-incharge. (Note:- Cement content considered in this item is @ 330 kg/cum.Excess/less cement used as per design mix is payable/ recoverableseparately). |
| 198 | Supply and fixing of UPVC S.W.R. pipe type -B confirming to IS- 13592 including jointing the pipes with rubber ring, lubricant and UPVC SWR cuplar confirming to IS - 14735. Also including excavation of trenches cutting of walls and holes and repairing the walls floors and refilling the trenches as before but excluding supply and cost of other fittings such as elbow, bead, tee and Y-tee including supply of all material labour and T&P .Required for proper completion of the work:160 mm O.D. (For RWH) |
| 199 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level: 300 mm dia ( for submersible boring) |
| 200 | 300 mm dia ( for RWH) |
| 201 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All type of soil: 300 mm dia |
| 202 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 100 mm nominal size dia |
| 203 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia ( for submersible boring) |
| 204 | 100 mm nominal size dia ( for RWH) |
| 205 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge. |
| 206 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 207 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.. |
| 208 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
| 209 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 210 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of :100 mm dia |
| 211 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp. |
| 212 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 100 mm dia. |
| 213 | Supply of submersible pump of make KSB 2.0HP with control panel, support wire etc. complete. |
| 214 | Providing 2 core PVC insulated submersibble cable from pump panel to submersible pump |
| 215 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work- 32 mm dia nominal bore |
| 216 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore. |
| 217 | EXTERNAL LIGHTING: S & F decorative hot dipped galvanised mild steel step pole 4 mtr. for post top light complete as required. |
| 218 | Supply and fixing of decorative 30 to 40 Watt LED Post top indirect light luminaire having Pressure die cast aluminium body and Clear glass with driver set confirming to IP 65 and above protection complete in all respect. Make Havells |
| 219 | Supply and fixing of LED Gate light fitting having die cast aluminium body and diffuser with driver set suitable for 6 watt to 10 watt. Confirming to IP 54 and above protection complete in all respect. |
| 220 | Supplying,installation,testing and commissioning of Astronomical time switch of following configuration to be mounted in feeder pillars / Lighting DBs for automatic switching On & OFF of street lights at sun set & sun rise or twilight(Auto ON, Auto OFF, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site complete as required: 1 output per phase and suitable for single phase supply |
| 221 | Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required: 32 mm dia |
| 222 | S&F of 32 Amp 415 V metal clad TPN HRCtype switch fuse unit complete with HRC fuse on angle iron bracket complete in all respect. Cat. B |
| 223 | S&F of 32 Amp 240V SPN metal clad rewireabletype switch fuse unit on M.D.F.E.G. / Teak wood board complete in all respects. Cat. B |
| 224 | Supply and fixing following capacity of automatic street light cubicle control panel painted with anticorrosive alkali and acid proof paint consisting of timer switch TSO 100 series with contractors HRC fuses, isolating switch Metreing instrument and instrument box with CTS etc. in case of TPN complete in all respects including the cost of fixing materials, labour T & P etc. as per direction and satisfaction to the E/I: 15 A SPN |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
