|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand(zone-III) : 8 graded stone aggregate 40 mm nominal size). |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 5 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 6 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 7 | Providing and fixing up to floor five level precast cement concrete hollow block including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete. 1:1½:3 (1 Cement : 1½ coarse sand(Zone III) : 3 graded stone aggregate 20 mm nominal size). |
| 8 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 10 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 11 | Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 12 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. Cold twisted bars |
| 13 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) |
| 14 | 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) |
| 15 | Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes.GI pipes |
| 16 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 17 | Precast terrazzo tiles 22 mm thick with graded marble chips of size upto12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1cement:4 coarse sand) : Medium shade pigment using 50% white cement and 50% ordinary cement. |
| 18 | Providing and fixing Stainless Steel welded crimped wire mesh of mesh size thickness 2mm opening 15mmx15mm (square/hexagonal) on the frames etc all complete including necessary fittings like screws & G.I wires as per the direction of Engineer in charge |
| 19 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade: Two or more coats on new work. |
| 20 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ( + 0.05 %), total coated thickness with zinc coating 120 gm per sqm as per IS:277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 21 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 gm per sqm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter .(600 mm over all girth). |
| 22 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth. |
| 23 | Providing and fixing 12 mm thick toughened glass of approved brand and manufacture, including fixing arrangement with necessary fittings and making necessary holes etc.all complete as per direction of Engineer-in-charge. |
| 24 | Providing and fixinguPVCframe (Solid) size 75mm x 65mm thickness 6mm for 12mm thick glass pane, corners of the frames to be fixed with the wall with solvent and stainless steel screws as per manufacturer’s specification and direction of Engineer-in-charge |
| 25 | Providing and fixinguPVC Door frame size 75mm x 65mm and panel frame of 65mm x 60mm (solid thickness 6mm) with 4mm glass pane & WPC board of 12mm thickness, corners of the frames to be fixed with the wall with solvent and stainless steel screws, joints mitred and Plastic welded with necessary stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge |
| 26 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer. |
| 27 | Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm). |
| 28 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 25 mm nominal outer dia .Pipes. |
| 29 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) sintex nipple 25mm dia, having thermal stability for hot & cold water supply, including fixing the nipple to the pipe. This includes jointing& fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : |
| 30 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) union socket 25mm dia, having thermal stability for hot & cold water supply, including fixing the socket to the pipe. This includes jointing& fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : |
| 31 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) long bend 25mm dia, having thermal stability for hot & cold water supply, including fixing the bend to the pipe. This includes jointing& fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : |
| 32 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) elbow 25mm dia, having thermal stability for hot & cold water supply, including fixing the elbow to the pipe. This includes jointing& fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : |
| 33 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) Tee 25mm dia, having thermal stability for hot & cold water supply, including fixing the tee to the pipe. This includes jointing& fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : |
| 34 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) Ball Valve 25mm dia, having thermal stability for hot & cold water supply, including fixing the valve to the pipe. This includes jointing& fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : |
| 35 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) plain socket 25mm dia, having thermal stability for hot & cold water supply, including fixing the socket to the pipe. This includes jointing& fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : |
| 36 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) Female Thread Adaptor 40mmx25mm, having thermal stability for hot & cold water supply, including fixing the adaptor to the pipe. This includes jointing& fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : |
| 37 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) Male Thread Adaptor 40mmx25mm, having thermal stability for hot & cold water supply, including fixing the adaptor to the pipe. This includes jointing& fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : |
| 38 | Providing and fixing G.I Tee40mmx25mm, having thermal stability for hot & cold water supply, including fixing the tee to the pipe. This includes jointing, cutting of threads& fittingsand testing of joints complete as per direction of Engineer in Charge. : |
| 39 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 40 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. 110 mm diameter |
| 41 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Coupler 110mm |
| 42 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend |
| 43 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate |
| 44 | Electrification lumpsum for providing wiring with 2.5 & 1.5 sqmm wire & LED lights and including necessary fittings and labour charges wherever necessary as per the direction of engineer -in-charge |
