|
| 1 | Earthwork in excavation of foundation trenches or drain, in all sorts of soil (including mixed soil, but excluding laterite or sand stone) including removing spreading or stacking the spoils within a lead of 75 mtr. As directed. The item includes necessary shoring. |
| 2 | Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with powdered earth or local sand. |
| 3 | Cement concrete with graded jhama khoa (30mm size) excluding shuttering in ground floor in foundation (1:3:6) proportion. |
| 4 | Brick work with 1st class bricks in cement mortar ( 6:1 ) (a) In foundation and plinth |
| 5 | (b) In superstructure, ground floor |
| 6 | Hire and labour charges for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works. (upto roof of ground floor) |
| 7 | Ordinary Cement Concrete(mix1:1.5:3)with graded stone chips(20 mm nominal size) excluding shuttering and reinforcement, if any,as per relevant I.S codes. |
| 8 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups,binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape,placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction. For works in foundation, basement and uptoroof |
| 9 | Labour for Chipping of concrete surface before taking up Plastering work |
| 10 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or rougening of concrete surface, including throating, nosing and drip course where necessary ( Ground floor )20 mm. thick plaster |
| 11 | 15 mm thick plaster |
| 12 | With 4:1 cement mortar 10 mm thick plaster |
| 13 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). Tor steel/Mild steel |
| 14 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position butexcluding the cost of hinge and other fittings. In ground floor.35mm thick shutters with 19mm thick panel of size 30 to 45 cm Sishu,Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 15 | (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S,W.I. Flats and bars of windows, railing etc.fitted and fixed with necessary screws and lugs in ground floor. |
| 16 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) |
| 17 | Supplying, fitting and fixing of but hinges with steel scrws for door and windows of size 50mm x 40mm x 2.5mm |
| 18 | i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting 75mm long x 10mm dia bolt |
| 19 | Anodised aluminium barrel/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to IS 204/74 fitted and fixed with cadmium plated screws |
| 20 | ASF in floor and dadoo, staircase etc with cement concrete 1:2:4 with sone chips laid in panels as directed. 35 mm thick |
| 21 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. Solvent based interior grade Acrylic Primer. One coat |
| 22 | Aplying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. |
| 23 | Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) Standard Quality |
| 24 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost ofprimer. In Ground floor (Two Coat) Normal Acrylic Emulsion |
| 25 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 26 | Priming one coat on plastered or other timberl surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 27 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :On timber or plastered surface :Two coats (with any shade except white) |
| 28 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :On steel or other metal surface :Two coats (with any shade except white) |
| 29 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand |
| 30 | Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer\"s specification for water proofing layer in water tank etc |
| 31 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) |
| 32 | Labour for boring tubewell of required dia by water jet system through any type of soil strata including hire and labour charges for boring pipes, scafolding, tool and plants as necessary and taking out them and lowering pipes, strainers, blind pipe etc. and fitting and fixing the same complete including bucket washing and other identical works in the connection. The tubewell should have a minimum 50mm gap inbetween the outside of the tubewell pipe and the bore.For depth upto 150 metre for 40 mm dia tube well with top enlargement of 100 mm dia.100 mm dia boring etc. top enlargement. |
| 33 | 40 mm dia boring |
| 34 | For depth more than150 metre iii. 40 mm dia boaring |
| 35 | Solvent cement 250 gm container |
| 36 | Collecting sample of water for bacteriological and chemical test for any depth at any time during execution of the work including hire and labour charges for tools and plants ant sterilising the equipments, paying all charges, testing etc. complete in all respect as per direction. |
| 37 | 100mm x 40 mm reducing PVC socket (heavy type) |
| 38 | Supplying, fitting and fixing plug of approved make conformimg to I.S specifications. 40mm |
| 39 | Steel cutter 450 mm long with socket of 40 mm dia |
| 40 | High density polythine strainer of approved make conformint to IS specification of 40 mm dia. |
| 41 | Supplying, fitting and fixing special hand pump no. 6 of approved make(for 50 mm or 40 mm dia. tube well). |
| 42 | PVC rigid pipes & fittings (Medium duty) conforming to ASTMD- 1785 and threaded to match with GI pipes as per IS-1239 (Part - I) 40 mm dia |
| 43 | PVC rigid pipes & fittings (Medium duty) conforming to ASTMD- 1785 and threaded to match with GI pipes as per IS-1239 (Part - I) 100 mm dia |
| 44 | Washing & developing of tube well with air compressor pump and engine for 8 (eight) hours continuous pumping per day with necessary arrangements for testing the yield in gallons per hour with \"V\" notch including hire and labour charges for all tools and scaffolding as required. |
| 45 | G.S.T |
| 46 | LWC |
