Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 30-08-2024 | Due Date Extended for tenders closing on 12-08-2024. | Admin Corrigendum Date Extend | 06-09-2024 |
| Sl. No. | Item Description |
| 1 | SCHEDULE A PART I (B/R WORKS)Dismantling of brick or terracing tiles of single layers on roofs incl cleaning of bricks/tiles and removal of unusable bricks/tiles and removal from site, complete all as specified. |
| 2 | Wire brushing and cleaning theroof surfaces with water including flashings and junction of parapets complete all as spd. |
| 3 | Demolition of mud in roof any thickness whether full thickness removed or part thereof including plaster & leaping complete all as specified |
| 4 | M&L for APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.0 KILOGRAM/SQUARE METREblack finish reinforced with non-woven polyster matt wt not less than 150 gms/SQUARE METRE with theRUNNINGMETREo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/SQUARE METRE torching over laps with a propane or abutan gas torch with a over lap of 75 mm at the side and 100 mm at the ends and sealing including applying a coat of cold emulsion bituminious primer all as per manufacturers instructions incl preparation of surface complete all as specified and directed. Note :- The water proofing treatment shall be got carried out by the manufactarer or their authorised applictor\"s duly approved by GE in writing. |
| 5 | Plain cement concrete (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified. |
| 6 | Material & Labour for PCC 1:2:4 type B-0 (using 12.5 mm graded mechanical crushed aggregate) for benching, coving shall be 150 mm in radius mixed with acrylic based polymer water proofing compound, complete all as specified & directed by Engineer-in-Charge.(WPC shall be paid separately) |
| 7 | Precast PCC plain factory made tiles,ISI marked,22 mm thick of size 250 mm x 250 mm, fabricated using grey cement & no pigments. on 15 mm thick cement mortar (1:3) bedding and joints grouted flush in cement mortar (1:3) mixed with integral liquid water proofing compound over roof surfaces complete all as specified. |
| 8 | M & L for cutting holes n. exc 150 Sq. cm into or through brick walls built in cement mortar and making good in cement concrete 1:2:4 type B01 as required complete. |
| 9 | Demolition of cement concrete (any type)for existing sunken portion of WC/Floortrap incl removing of all debris from site to a distance exc 250 m but not exc 500m and deposited where directed incl cleaning of surface with wire brushes and water complete all as specified and directed |
| 10 | M& L in repair for 40mm dia (Bore) GI pipe medium grade as in spout complete all as specified and directed. |
| 11 | M& L for PCC 1:5:10 type E2 using 40mm graded aggrgate as in filling in sunken portion floor ,rounded or chamfered on edges complete all as specified and directed. |
| 12 | M & L for sunken floor water proofing treatment complete all as under - (a) scrapping the surface with wire brush and cleaning with water and allow to dry (b) Applying cement slurry @ 3.0 KILOGRAM/SQUARE METRE duly mixed with water proofing compound (C) 15 mm thick cement plaster 1:3 with additional floating/setting coat mixed with water proofing compound as per manufacture instruction ( the corner will made rounded in concave shape)(D) Applying cement slurry @ 3.0 KILOGRAM/SQUARE METRE duly mixed with water proofing compound (E) apply one coat of hot bitumin grade 85/25 confoRUNNINGMETREing to IS 702 @ 1.2 KILOGRAM/SQUARE METRE . (f) supply and laying APP with nin woven polyster reinforced sheet 3mm thick weight not less than 3.00 KILOGRAM/SQUARE METRE (G) applying one coat of hot blown bitumin grade 85/25 confoRUNNINGMETREing to IS-702 @1.20 KILOGRAM/SQUARE METRE (H) curing the sunken portion with water min 48 hours by ponding. (Water proofing shall measured and paid separately) |
| 13 | Demolition of brick work built in CM incl all quions arches, pillar etc all as specified and directed. |
| 14 | Material and labour for brick work withold size sub class ‘B’ bricks,straight or curved on plan to any radiousl built in cement mortar (1:4) complete all as specified. |
| 15 | All as per Item No 202above but except bricks. |
| 16 | Material & labour Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 etc complete all as specified and directed . |
| 17 | Taking down Cement plaster on brick or stone walls incl raking out joints hacking for key & scrubbing down with water etc compplete all as specified and directed. |
| 18 | M&L Rendering 15 mm thickon fair faces of brick work or concrete surfaces, finished even and fair (without using extra cement) on walls in cement mortar (1:6), complete all as specified. |
| 19 | M&L Rendering 10 mm thickon fair faces of brick work or concrete surfaces, finished even and fair (without using extra cement) on walls in cement mortar (1:6), complete all as specified. |
| 20 | Rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), using water proofing compound complete all as specified.NOTE:WPC will be measured and paid for separately |
| 21 | M&L for rendering 5mm thick in (1:3) cm on fair faces of ceiling.finished even and smooth without using extra cement.complete all as specified and directed. |
| 22 | Material & labour for rough cast plastering over and incl 10 mm thick rendering in cement mortar 1:3 and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than noRUNNINGMETREal for rendering to ensure that larger aggregates are thoroughly covered. Rough cast plaster shall be applied asspecified clause 14.22 of SSR Part-I . |
| 23 | Supply only liquid water proofing comound ISI Marked complete all as specified and directed. |
| 24 | Material & labour 5 mm thick cement plaster in CM 1:3 as in soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth w/o using extra cement etccomplete all as specified and directed . |
| 25 | Description all as per item no 11 above dut over and incld dubbing out average 10 mm thick on irregular surfaces of soffit of slab/chajjas/sunshades etc in CM 1:4 |
| 26 | M&L fo providing one layer of guiniting of thickness not exceding 50 mm provided steel reinforcement and chicken wire mesh if required by means of tinned tracks or welded to existing reinforcement in CM 1:3 for top & bottom of roof slabs, beams, columns and staircase ets as directed incl scaffholding at any height all as directed incl MSchicken wire mesh of weight exceeding 0.25 KILOGRAM/SQUARE METRE and n.exe 4KILOGRAM/SQUARE METRE all as directed. |
| 27 | M&Lpreparation of exposed brick wall surface by cleaning the surface with wire brush to remove all dirt/loose materials from the bricks and from the joints between the bricks.Prepared surface should be then washed with diluted HCL acid (dilution ratio of 1:50) for three times in a day for two days. After acid wash surface should be allowed to be air dried for one day.Note : Further treatment over the surface so achievedwill be carried out only after approval of the same by GE.Note:- This item shall be executed by authorised applicator only. for carrying out efflorescence treatment to exposed and prepared wall surfacehere–in–abovein following sequence :–(a) Prime the prepared surface with one of the following product mixed with cement in 1:1ratio as bonding agent :–(i) Pidicrete URP of M/S Pidilite(ii)Sika Latex of M/s Sika(iii) Nitobond SBR Latex of M/s FOSROC(b) Immediately after priming the surface PMM (Polymer Modified Mortar) to be applied \"BY HAND\" while the primer is tacky.PMM should be prepared by mixing one of the following compounds in Cement Mortar 1:3 as per manufacturer\"s instructions :–(i) Pidicrete URP of M/S Pidilite(ii)Sika Latex of M/s Sika(iii) Nitobond SBR Latex of M/s FOSROC(c) PMM surface should be allowed to dry one day.After that it shoud painted with two coats of one of the following compound mixed with cement only in ratio of one part of selected compound and one point fire part of cement :–(i) Pidicrete URP of M/S Pidilite(ii)Sika Latex of M/s Sika(iii) Nitobond SBR Latex of M/s FOSROC(d)Now apply two coats of one of the following compound over the surface.These compounds are to be used as per manufacturer instructions :–(i) Pidifin 2K of M/S Pidilite(ii)Brush Coat of M/s Sika(iii) Brush Bond of M/s FOSROCNote : Both coats should be perpendicular to EACH other and gap between two coats shall be minimum 6 hours.(e) Sprinkle loose coarse sand after second coat while surface is tacky.Note: (i) Item will be executed by authorised applicator of the selected /approved company only. (ii) Every stage of work will be approved by GE then only next layer will be executed by contractor. |
| 28 | Material and labour for applying waterproof cement based putty @0.80KILOGRAM (undiluted) per SQUARE METRE of average thickness 2.50mm in two coats on prepared / newly plastered wall (external/ internal) and ceiling surfaces as per item No 1.00& 10.00 in following steps- (i) Filling cracks in wall using crack seal compound Asian smart care crack seal or equivalent(ii) Mix the putty @ 0.8 KILOGRAM/SQUARE METRE by adding 35 to 40% water by volume or as per approved manufacturer\"s instructions & mix it with electric putty mixer with mixing capacity of min 2.5 KILOGRAM putty per minute upto 5 to 10 minutes(iii) Apply the first coat of prepared mix with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minute with max pressure 3300 PSI with bottom to top configuration and allow 6-8 hrs to dry the putty surface.(iv) Apply the second coat of prepared mix with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minute with maximum pressure 3300 PSI with horizontal configuration(v) Allow 6-8 hrs to dry putty surface then prepare the surface by electronic wall sander machine to apply subsequent coats of primer complete all as specified and directed. |
| 29 | Material and labour for applying two coats of oil bound emulsion distemper on prepared & primed wall ( internal) and ceiling surfaces of approved tint complete all as specified & as directed. |
| 30 | Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 31 | Demolition ofof reinforced Cement Conc of any description & in any position comp incl cutting of reinforcement complete all as specified and directed. |
| 32 | FoRUNNINGMETREwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc |
| 33 | Use and waste of foRUNNINGMETRE work to sides & soffits of plinth bands , lintel band, Shelves etc including, shelves etc. complete |
| 34 | Use and waste of foRUNNINGMETRE work to chajjas and similar work for fair finish surfaces all as spd. |
| 35 | M&L RCC Nominal Mixtype B1 using 20 mm graded stone aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span completeallas specified. |
| 36 | M&L Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like Type B1 1:2:4 (20 mm graded aggregate) |
| 37 | M&L for Reinforced Cement concrete Nominal Mixusing 20mm graded aggregates mechanically crushedas in chajjas etc complete all as specified and directed. |
| 38 | Material and labour mild steel 10 mm dia and over TMT bar cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 39 | Material and labour mild steel 6-8 mm dia TMT bar cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 40 | Description all as per item No 38 above but 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders etc.complete all as specified and directed |
| 41 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 42 | Demolition of Cement Conc.as in G.F & paving n. exc. 15cm thick (above or below G.L.) |
| 43 | M&L PCC 1:5:10 type E-2using40mm graded stone agg 75 mm thick as in sub base of floor complete all as specified and directed. |
| 44 | M&L 25mm thick cement concrete Type B1 1:2:4 (12.5mm graded aggregate)as in floor finished rough to recieve floor finishes etc |
| 45 | M&L First quality, Non skid ceramic, coloured, rectified i.e. straight edge (locally known as joint free) tiles of size 600 x 600mm EACH and of thickness not less than 7mm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to matchthe shade selected quality laid over and including 15mm thick screed bedding layer in CM (1:4) complete all as specified. |
| 46 | M&L First quality, Non skid ceramic, coloured, rectified i.e. straight edge (locally known as joint free) tilesof size 600 x 600mm EACH and of thickness not less than 7mm, in skirting etc. over & including 10 mm thick cement mortar (1:4) screed, set and jointed with tile adhesive with notched trowel and pointed in grout of matching shade of tiles, complete. |
| 47 | Material & Labournon skid coloured ceramic tiles 400 x 400 x 7 to 8 mm set & jointed with neat cement slurry & pointed in white/coloured cement to match the tiles over and including 15mm thick screed bed incement mortar 1:6 complete all as specified and directed. |
| 48 | Material & Labour for glazed ceramic colouredtiles 450x350x7 mm thick onvertical surface such as skirting , dado etc. over 10 mm thick backing coat plaster in CM 1:4 complete all as specified and directed. |
| 49 | M&L Vitrifiedceramic tiles light shade 10mm thick (Square/rectangular) polished, area of EACH tiles not exceeding 0.36 SQUARE METRE, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to matchthe shade selected quality laid over and including 15mm thick screed bedding layer in CM (1:4) make and sample as approved by GE/Engr-in-charge |
| 50 | M&L Vitrifiedceramic tiles 10mm thick (Square/rectangular) polished, area of EACH tiles not exceeding 0.36 SQUARE METRE, in skirting/dado etc set and jointed in neat cement slurry and pointed in coloured cement to matchthe shade selected quality laid over and including 10mm thick screed bedding layer in CM (1:3) make and sample as approved by GE/Engr-in-charge |
| 51 | Machine cut Kota stone slab flooring 18-22 mm thick, for staircase step in single piece (of length not more than 1200 mm), laid over over & including 15 mm thick (average thickness) cement mortar (1:3) screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete, includingprovn oftwo Nos 3x3mm grooves at tread of EACH step complete all as specified. |
| 52 | Machine Cut Kota stone slab 18-22 mm thick on vertical surfaces like riser of steps, skirting, in single piece (of length not more than 1200 mm) over & including 10 mm thick (average thickness) cement mortar (1:3) screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Mirror finish), complete all as specified. |
| 53 | M&L Machine cut Kota stone slab flooring 20-25 mm thick, laid over & including 20 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified. |
| 54 | M&L Machine cut Kota stone slab flooring 20-25 mm thickskirting, dado and pillar, laid over & including 10 mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified. |
| 55 | M&L Granite jet black shade, 15-18 mm thick, machine cut, machine polished,bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 15 mm thick(average thickness) cement mortar(1:4) screed, as in cookingplatfoRUNNINGMETRE,shelves,RCCcounters,windowcills&similarsituations,completeallas specified. |
| 56 | Baroda Green marble, 15-18 mm thick,machine cut, lapd over & including 15 mm bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 15 mm thick(average thickness) cement mortar(1:4) screed, as in cookingplatfoRUNNINGMETRE,shelves,RCCcounters,windowcills&similarsituations,completeallas specified. |
| 57 | Baroda Green marble, 15-18 mm thick,machine cut, lapd over & including 15 mm bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 15 mm thick(average thickness) cement mortar(1:4) screed, as in Tread of Stair casecompleteallas specified. |
| 58 | Baroda Green marble, 15-18 mm thick,machine cut, lapd over & including 15 mm bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 15 mm thick(average thickness) cement mortar(1:4) screed, as in Riser/skirting of Stair casecompleteallas specified. |
| 59 | Rounding to edgesof stone (of any description) slabs one edge, such as in steps, cooking platfoRUNNINGMETRE, and other similar situations including rubbing and polishing (mirror finish), complete all as specified. |
| 60 | Cement concrete75 mm thick 1 :2 4 type B 2 using 40 mm graded stone aggregate as in flooring, finished cement concrete surface even andfair with outusing extra cement to be laid in alternate panels as directed complete all as specified |
| 61 | M&L 40 mm thick cement concrete type B-1 , 1:2:4 (20 mm graded crushed stone aggregate) as in PCC flooring finished the concrete surface even and smooth w/o using extra cement complete all as specified and directed. |
| 62 | M&L 40 mm thick cement concrete type B-1 , 1:2:4 (20 mm graded crushed stone aggregate) as in PCC flooring incl spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed. |
| 63 | Glass dividing strips, 3mm thick and inserted in position to confoRUNNINGMETRE to design and width of strip 38mm complete all as specified and directed. |
| 64 | Taking down chowkaths or frames n.exc 1.5 SQUARE METRE (without takingoff shutter from the frame) EACH and removing from the site including dismantling brick work for hold fasts etc |
| 65 | Taking down chowkaths or frames Exc 1.5 SQUARE METRE but n.exc 4 SQUARE METRE(without taking off shutter from the frame) EACH and removing from the site including dismantling brick work for hold fasts etc |
| 66 | Taking down shutters of any description n exc 1 SQUARE METRE EACH and removing from the site. |
| 67 | Description all as per item no 61 above but exc 1 SQUARE METRE EACH and nexc 2 SQUARE METRE EACH . |
| 68 | Taking downof wooden door shutter of any description area exceeding 1 SQUARE METRE and n exc 2 SQUARE METRE EACH and refixing in same opening after repair/easeningcomplete |
| 69 | Dismantling structural steel work including doors, gates but excluding framed truss etc. |
| 70 | M & L for Erection and fixing only of framed work as in doors or gates of angle or other section with gusset plates, rails, braces, ect.. Complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and fixing complete. |
| 71 | S& F Pressed steel frames of size 125 x 60 mm for doors with one or more rebates including fixing lugs, 125 mm size hinges, lock strike plate, etc., complete, as specified, supplied and fixed . |
| 72 | S& F Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including fixing lugs,125 mm size MS hinges, lock strike plate, etc., complete, as specified, supplied and fixed . |
| 73 | M & L 40mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on one face and decorative face veneer with lipping on one face complete all as specified. |
| 74 | S&F 35 mm thick factory made glazed & Skelton shutter of IInd class H/Wood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2010). |
| 75 | S&F Factory solid PVC door frames of size 120mm x 60 mm made with one or more rebates including fixing lugs/holdfast, 125 mm size Stainless hinges(03 Nos), lock strike plate, etc., complete of colour choiceallas specified and directed, MaKeECCO CELLand equivalent |
| 76 | S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with locking arragement inluding 20mm SS tower bolt (02 Nos),150mmgrip SS Handle (02Nos), in door at site of colour choice all as specification colour WOOD COLOUR |
| 77 | Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in EACH shutters) (45.5mm x 28mm),Glazing bead (24.5mm x 16mm) will be miterd cutand fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware[Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)(Note: The unit rate quoted by contractor includes cost of 5mm thick dark glass,stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position,and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 78 | Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm) Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated),But Hinges of\"zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor includes cost of 5mm thick dark glass,stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position,and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 79 | Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 SQUARE METRE.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foRUNNINGMETREing process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing &direction of Engineer-in-Charge.(Note: The unit rate quoted by contractor includes cost of 4mm thick pin headedglass, and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 80 | Supply & fixing Brass, sliding door bolt 250 mm long with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed |
| 81 | S&F 200 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed |
| 82 | Supply & fixing Extruded brass handles,fabricated type polishedtype handle 150 mm long complete all as specified & directed. |
| 83 | Material and labour PCC 1:3:6 type C-1 (20 mm graded mechanically crushed stone aggregate) as in filling pressed steel frame /hold fast blocks etc complete all as specified and directed. |
| 84 | S&F mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Fe 310-0 complete all as specified. |
| 85 | Supply & fixing Mild Steel Framed work such as Guard Bar/grill welded to window frame or fixed independantlys, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confoRUNNINGMETREing to Fe.290.Gde-E-165 complete all as specified & directed. |
| 86 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples |
| 87 | M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applyingtwo coat of syntheatic enammel paint over one coat of pink primer all as specified. |
| 88 | Material & labour for painting to steel surfaces of any description not other wise described over 10cm width or girth with two coats of synthetic enamel paint over one coat of red oxide primer incl preparation of new surfaces complete all as specified and directed by Engr-in-charge |
| 89 | Material andlabour for preparation of veenred wooden surfaces of any description over 10cm width or girth and applying two coats of melamine polishing of approved brand to wooden surfaces including filling , sanding,spraying allas per manufacturo instructionand directed by Engr in charge. |
| 90 | S&F 300 mm MS ordinary rat tail rod pattern springs incl roller and roller plate fixed to wooden chwkhats or welded to angle iron door frames. |
| 91 | S&F small articles such as door stoppers etc of IInd class H/Wood.Incl all necessary labour area not exc 200 cu cm EACH with 50mm long cold rolled mild steel butt hinge medium weight all as specified and directed |
| 92 | Preparation of old painted wooden surfaces of any description not otherwise describedover 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed. |
| 93 | Preparation of old steelsurfaces of any description over 10cm width or girth not other wise described applying two coats synthetic enamel paint complete all as specified. |
| 94 | S&F 100mm long hasp and staple sofety type Aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws. |
| 95 | S & F stainlesssteel curtain rod 25mm dia having wall thickness 1.6mmfixed with and including stainless steeldecorative brackets, two lotto for EACH road length at both endetcas in repair complete all as specified and as directed by the Engineer-in-Charge. |
| 96 | Factory made mild steel door shutter with frame, fabricated from of 1 mm thickMS sheetincluding provision of steel handle & locking arrangement by providing 04 leaver lock with duplicate keys (of make Godrej, Link or Harrison) & handle etc, (all as per Godrej pattern & detail shown on Drawing No. FD-1032 sheet 1/1 dtd 25.9.93) including spray painting over a coat of red oxide primer and fixed the same on existing cupboard nitch with cement & sand mortar, complete. |
| 97 | S & F rubber strips 3 to 4mm thick & 65mm to 75mm wide fixed on bottom rail of door for covering gaps between door & floor to aviod entry of insects,dust etc complete . |
| 98 | S&F 150 mm overall length of cover plate Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete as all spfd and directed by EIC |
| 99 | Dismantling woodenboarding any description, fixed in any position with nails as in shelves of cup board and pelmets of any description. |
| 100 | S&F for LEAD FREE PVC Celuka ply 18mm thick (Minimum density 600KILOGRAM/CUBIC METRE) of both side plain white colour, fixed with stainless steel screws, solvent cement /adhesive to make kitchen /bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed by Engr–in–Charge. |
| 101 | S&F for LEAD FREE PVC Celuka ply 18mm thick (Minimum density 600KILOGRAM/CUBIC METRE) of single side rigid lamination of approved colour and other side plain white colour, fixed with stainless steel screws, solvent cement /adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer’s specifications complete all as specified and directed by Engr–in–Charge. |
| 102 | S&F for 12mm thick LEAD FREE PVC Celuka ply (Minimum density 600KILOGRAM/CUBIC METRE) of fixed with stainless steel screws, solvent cement /adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed by Engr–in–Charge. |
| 103 | S&F for stainless steel 304 grade wire basket cutlery of size 370 x 485mm premium quality fixed in position complete all as specified and directed by Engr–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON and GODREJ. |
| 104 | S&F for stainless steel 304 grade wire basket (average weight 2.5 to 4 KILOGRAM per Basket) of pull out type like plain /cup & saucer /bottle /multi purpose /2–3 shelf basket etc for kitchens of required size fixed in position complete all as specified and directed by Engr–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON and GODREJ. |
| 105 | S&F for Ball bearing runners 45mm telescopic (KTS–20) full extension load capacity minimum 50KILOGRAMs complete all as specified and directed by Engr–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON and GODREJ |
| 106 | S&F for ‘D’ type cabinet handles premium quality, stainless steel grade 304, gloss chrome, SN finished 150mm long matt finishedcomplete all as specified and directed by Engr–in–Charge. Make: HETTICH, KAFF, GLEN, HARRISON and GODREJ. |
| 107 | S&F for Auto closing hinges of size 35mm of 0 crank (KH–001) of 8 crank (KH–002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed by Engr–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON and GODREJ. |
| 108 | Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site |
| 109 | Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site |
| 110 | Supply & fixed GI tubing medium grade 15 mm dia incl fittings, cutting threading and fixing to walls or fixing in concealed walls or in floors etc, and making good the surfaces matching to exsiting surafaces of walls/ floor to the entire satisfaction of Engineer-in-charge. |
| 111 | Supply & fixed GI tubing medium grade 20 mm dia incl fittings, cutting threading and fixing to walls or fixing in concealed walls or in floors etc, and making good the surfaces matching to exsiting surafaces of walls/ floor to the entire satisfaction of Engineer-in-charge. |
| 112 | Cuttingchases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends of edges of landings, steps, cills etc., and cutting chases for concealed water tubing and making good complete. |
| 113 | Refixing old GI tuibing 15mm bore galvanised with all fittings as in walls,ceilings or floors etc complete. |
| 114 | Refixing old GI tuibing 20mm bore galvanised with all fittings as in walls,ceilings or floors etc complete. |
| 115 | Dismantling old unserviceable cement concrete/PVC water tanks of capacity exc 250 ltrs & n.exc 500 Ltrs including supplying & fixing of PVC water storage tank 500 ltr capacity HDPE triple layered ,white colourcylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight20 mm - 210 gms ) fixed as in repairs.N ote :(i) Inlet, outlet & wash out pipe will be measured paid for separately. |
| 116 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.(cleaning reparing etc measured separately). 500 litre |
| 117 | Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. of tank capacity n exc 500 Ltr complete all as specified. |
| 118 | S&F in repairs,Vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe, P or S trap,) all as specified. |
| 119 | S&F in repairsfor PVC water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified. |
| 120 | Supply & fixedin repairsvitreous China squatting pan of “Orissa Pattern” of size 580x440mm colouredwith integral footrest complete including making good floors complete all as specified. |
| 121 | S&F in repair10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe all as specified. |
| 122 | Supply andfixedin repair vitreous china wash hand basin white flat back of size 550x440mm including CI brackets ,chromium plated waste coupling, waste pipe etc.,complete all as specified. (incl all waste fittings) |
| 123 | Supply only pillars taps fancy typechromium plated cast copper alloy with capston head long screwed shanks of 15mm bore compete all as specified. |
| 124 | S&F in repair Brass CP WHB Mixer valve for mixing hot and cold water screwed down for 15mm dia iron pipe all as specified. Make : Jaquar Cat Part No. CON-167KNBand equivalent |
| 125 | S&F in repair chromium plated hand shower (health fauset), telephonic type with 8mm dia, 1.5 meter longpvctube coverCP flexible with wall hooksuitable for 15 mm bore iron pipes or for unions and fixed complete all as specified and directed.Make Jaquar Cat Part No. ALD-587and equivalent |
| 126 | S&f as in repair JET fighter spray with flexible aRUNNINGMETRE complete for EWC as all spfd and directed by EIC. |
| 127 | S&F in repair Chromium plated toilet paper holder. Make:-Jaquar Cat Part No. CAN-1151Nand equivalent |
| 128 | S&Ftwo way bib Tap chromium plated brass fancy type of 15 mm bore complete as all specified and directed by EIC .Make Jaquar Cat Part No. CON-041KNand equivalent |
| 129 | S&F chromium plated hand showerwith 1.5 mtr long flexible tube withwall mixer telephonic type completewith provision for overhead shower with 115 lond bad pipe on upper side, connecting legs & Wall flange all as specified and directed complete all as specified and as directed by engineer in charge . Make Jaquar Cat Part No. CON-273KNUPR &equivalent |
| 130 | S & F of stainless stell peg set of 06 Nos hook all as specified and directed |
| 131 | S&F for corner glass shelf with CP stand complete all as specified. |
| 132 | S&F in repair Towel ring square with round flange of make JAQUARor Equivalent. |
| 133 | S&F in repair 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles scrwed down suitable for 15mm bore pipe or union in repair complete all as spd.Make : Jaquar Cat Part No. CON-107KNand equivalent |
| 134 | S&F in repairBib tap, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, suitable for 15 mm bore pipe, complete all as specified. Jaquar Cat Part No. CON-037KNand equivalent |
| 135 | Supply & fixed in repairs stainless steel grating openable 100mm SQUARE METREm size with/without hole including fixing with white cement complete all as specified. |
| 136 | S&F in repair angle valve cock chromium plated fancy type 15 mm bore with flangecomplete all as specified. MakeJaquar Cat Part No. CON-053KNand equivalent |
| 137 | S&F in repairchromium plated Stop valves, cast copper alloy, screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 20mm bore. |
| 138 | Supply & fixedin repair fancy type shower rose125mm dia sizeof Rim and 30cm long CP brass pipe with swiwel joint in complete all as specified. |
| 139 | S&F in repair sheet glass shelf assembly consisting of 5.5 mm th sheet glass shelf 12 cm wide with chromium plated guard and railing 60 cm long. |
| 140 | Supply & Fix in repairCP Soap dish any type, fixed to plugs with chromium plated brass screws. Make Jaquar Cat Part No. CAN-1131Nand equivalent |
| 141 | S & F in repair chromium plated, towel rail, 20mm dia, D type, 60cm long between flanges. |
| 142 | S&F in repairfor PVC connections 15mm size with PTMT nuts of length 450mm |
| 143 | S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe incl bedding in cement mortor to dwarf wall ot cantilever brackets and connecting union to pipe overall size 915x460mm, bowl size 410x 330x160mm incl all fittings ie CP waste coupling, waste pipe complete all as specified. |
| 144 | S&F 600x450mm size bevelled edge looking mirror of selected quality glass mounted on 12mm thick marine plywood with powder coated aluminium frame alround and fixed with wooden plugs, CP screws, cup and washers. |
| 145 | S&F in repairs PVC cabinet with looking mirror of size 350x450mm complete all as specified and directed. |
| 146 | S&F stainless steel plate rack standard size 1000mmx750mm mm complete and fixing with rawl plug and steel screws of wt not less than 8KILOGRAM EACH |
| 147 | Demolition and breaking up drain pipes 75/100 mm dia, SGSW,AC, PVC, concrete pipe including fittings, complete all as specified and as directed. |
| 148 | S & FPVC (SWR)110mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 149 | S & FPVC (SWR)75mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 150 | S &F PVC (SWR) bends of 75mm radius |
| 151 | S &F PVC (SWR) bends of 110mmradius |
| 152 | S& F PVC (SWR) junction single, (Single T) equal or unequal of 110mm dia with access door all as specified and directed |
| 153 | S & F PVC (SWR) vent cowl of 110mm dia |
| 154 | Supply & Fixing PVCP or S trap 100 mm bore |
| 155 | M & LPVC (SWR) floor trap, plain including jointing with solvent all as specified and directedcement of outter diameter outlet of 100mm as in repairs |
| 156 | M&L stack clamps of 50mm by 5 mm flat iron and 16 mm dia round iron stays, incl bolts & nuts and securing ends of stays to wall or roof for 100 mm bore CI Pipe complete |
| 157 | M&L for salt-glazed stoneware gully traps,150x150 square or round mouthed, type \"P\" setting and jointing to drains with cm 1:1. |
| 158 | Demolition and breaking up 150 mm bore drain pipes (salt glazed stone ware pipes) set in cement mortar complete all as specified. |
| 159 | Excavation in trenches n.exc 1.5 M wide and n.exc 1.5m deep as in soft/loose soil for foundation etc or for shaft walls, cesspit, manhole etc n.exc 10SQUARE METRE on plan |
| 160 | Returning, filling including spreading, levelling and well ramming in layers not exceeding 25 cm in EACH layer as in soft / loose soil complete. |
| 161 | Removingexcavated material and debries obtained from demolistion toa distance exc 250 m but n exc 500 m and depositing where directed at a level n exc 1.50m above the starting point. |
| 162 | M&L for Concrete bed to drain pipes of 150mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 complete all as specified |
| 163 | M&L for 150mm Sail-glazed stoneware drain pipes laid in trenches and jointed as specified |
| 164 | Demolition of brick work built in CM incl all quions arches, pillar etc all as specified and directed. |
| 165 | Material and labour for brick work withold size sub class ‘B’ bricks,straight or curved on plan to any radiousl built in cement mortar (1:4) complete all as specified. |
| 166 | All as per Item No 202above but except bricks. |
| 167 | Material & labour Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 etc complete all as specified and directed . |
| 168 | M&L for rendering 15mm thick in CM 1:4on fair faces of brick work or concrete surface of wall and finished surface even and smooth with neeru finish to plastering as all specified complete all as specified and directed by EIC |
| 169 | M&L for providingPCC 1:2:4 type B-1 (20mmgraded stone aggregate )as in coping/ benchingetc including necessary foRUNNINGMETRE work complete all as specified and directed. |
| 170 | M&L for plain cement concrete 1:4:8 , type D-2 using 40 mm graded stone aggregate) as in fdn , filling and mass concrete complete all as specified and directed . |
| 171 | Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and foRUNNINGMETREing branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and refoRUNNINGMETREing benching as required for 150 mm dia pipe |
| 172 | Demolition ofof reinforced Cement Conc of any description & in any position comp incl cutting of reinforcement complete all as specified and directed. |
| 173 | M&L precast concrete cover slabs for drain man hole/drain etc.in (1:2:4) type B-1 using 20 mm mechanically crushed graded stone agg.set in CM (1:6) complete. |
| 174 | Material and labour mild steel 10 mm dia and over TMT bar cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 175 | M & L for Brick work with sub class ‘B’ bricks, straight or curved on plain exceeding 6 metre mean radius in cement mortar (1:6), complete all as specified and as directed by the Engineer-in-Charge |
| 176 | M&L for Rendering 15mm thickin CM 1:4 on fair faces of block masonry surfaces or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed by EIC |
| 177 | M&L prepration of newly plastered surface and apply two coat of cement base paint complete all as specified & as directed. |
| 178 | M & L for Framed work as in doors or gates (ornamental type) of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steelsheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete confoRUNNINGMETREing to Fe-410-W(Gde- E-250) quality-A |
| 179 | Demolition of cement concreteunreinforced of any description andin any position not otherwise specifically provided for. |
| 180 | M&L, 75 mm thick PCC (1:3:6) C-2 using 40mm graded stone agg in path/plinth protection finished even & smooth completed W/O using extra cement. |
| 181 | M&L PCC (1:3:6) C-1 using 20 mm graded stone agg as in surface channel or drain incl use of necessary from work for fair finishedsurface. |
| 182 | Extra for foRUNNINGMETREing fair finishing of drain or channel 30 cm inner girth in cement concret using extra cement including foRUNNINGMETREs, moulds mitrel gloppid ends etc |
| 183 | M&L Roof Trusses (framed) , trussed , purlins, crane gantries, rails and fastenings and heavy bracket framing ( Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete as all spfd and directed by EIC |
| 184 | M&L rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) foRUNNINGMETREing holes incl. rivetting, welding etc complete all as specified. |
| 185 | Supply and fixing inPre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directedby Engr-in-charge. |
| 186 | Surface dressing not ex 15 cm deep in soft/loose soil incl cutting of bushes / shrubs not exc 30 cm girth incl grubbing out roots complete all as specified. |
| 187 | Removing excavated soil exc 1.50km but n exc 5km and depositing where directed by Engr-in-Charge |
| 188 | M&L for 100mm thick cement concrete type D-2, 1:4:8 (40 mm graded aggregate) as in sub base complete all as specified. |
| 189 | M&L for sand filling under floor or in foundations including watering and consolidation complete all as specified as directed. |
| 190 | M&L for 60 mm thick coloured machine pressed precast concrete interlocking paver block any shape and size confiRUNNINGMETREing to IS 15658-2006 of 60mm thickness M-35 grade with gray cement and no pigment to match complete all as specified. |
| 191 | M&L for providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in copings, slightly, rounded or chamfered angles complete all as specified as directed. |
| 192 | S & F Steel rolling shutters 1.25mm thick with ball bearing, gear operated type with bevel gear box and crank handle alongwith Safety lever locks mild steel with 4 levers for rolling shutters as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated,complete: push pull or manual type all as speicified and directed |
| 193 | Removing building materials etc (other than spoil payable under items 03028 to 03031 in section 3-Earthwork) to a distance of 5KM or under beyond the lead included in the rates including loading, unloading and stacking at the destination complete |
| 194 | SCHEDULE A PART II (SMART PERIODICAL WORKS)Material and labour for applying one coat of acrylic water based exterior grade / interior grade primer @ 0.90 litre (undiluted) / 10 SQUARE METRE diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 lit per minute having a pressure of 3300 PSI on prepared ceiling or internal / external walls surfaces. Allow 6 - 8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed. |
| 195 | Material and labour for applying two coats of anti fungal weather proof grade exterior acrylic emulsion paint of approved tint @1.80 lit / 10 SQUARE METRE (undiluted) as per approved manufacturer\"s instruction over prepared and primed surface of external wall. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed.Notes for item Nos 194 & 195 :–The work for periodical services shall include the following and the rates quoted by the bidders shall include the same :–(a) The work pertaining to periodical services shall be executed by the contractor as per MoU from authorised applicator through manufacturer ofthe materials like Exterior Emulsion paint, putty etc after approval by the GE.(b) The Contractor shall upload with the documents under cover I \"Memoradum of Understanding\" (MOU) with at least one of the manufacturers mentioned in the contract, failing which the bid shall be laible to be rejected.(c) Use of Scaffolding, trestles, ladders, cradles etc necessary for execution of work and protective measures.(d) Removing of Nails, making good holes, cracks etc(e) Work in patches and in narrow /widths, bands, cornices, pilasters etc and cutting in edge of line where necessary.(f) Spreading and removing covering to doors, windows, floors, fittings etc to protect them from splashes.(g) Washing floors, cleaning glass, joinery, electric fittings, wirings etc. Drops and splashes of paint to be cleaned to the entire satisfaction of Engineer–in–Charge.(h) Sample patch of 10sqm be prepared considering all the items of periodical and shall be got approved from GE prior to carrying out further work. |
| 196 | SCHEDULE A PART III (E/M WORKS)Material and Labour for Taking down Copper/Aluminium point wiring (light, fan, socket or power) complete, any type / size complete with removing all connection and accessories, fittings and fixturessuch asswitches , sockets, ceiling rose,pendent holder,fan regulator any type , all type of tube light fitting , batten , steel or PVC conduit , casing caping etc compele and making good the disturbed surface of wall , floor etc. complete all as specified and directed by Engineer-in-Charge. |
| 197 | Material and labour for Point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 Sq. mm (nominal area), single core, FRLS, PVC insulated and unsheathed stranded cable 1100 volts grade, ISI-694 marked TEC and FIA approvedin and including heavy duty PVC concealed conduit and its fittings,ISI marked,PVC junction boxes, modular metal sunken/flush boxes with suitable modular cover plate including FRLS rigid PVC insulated unsheathed strandedcopper conductor 1.5 Sq. mm nominal cross sectional area wire as earth continuity conductor upto common earth and connecting to common earth dolly complete and including cutting/chasing of wall complete all as specified and directed by Engineer-in-Charge for the following:- |
| 198 | (a) One light point controlled by one switch/one fan point controlled by one switch and fan regulater. |
| 199 | (b) socket outlet 3 pin, 5 Amp on independent board. |
| 200 | (c)Socket outlet, 3 pin,5 Amp on the same board with other switches. |
| 201 | (d) One light point controlled by two,2way switches. |
| 202 | (e) One bell/buzzeer point controlled by one bell push button on the same board with other switches or independent |
| 203 | Material and labour for Point wiring using approved colour coding as per IS with stranded copper conductor 2.5 SQUARE METREm (nominal area ),single core ,FRLS PVC insulated and unshaethed stranded cable 1100 volts grade ISI-694 marked TECand FIA approved in and including heavy duty ,PVC concealed conduit ISI marked for one 3 pin 15 Amps modular socket outlet on independent board with earth dolly including FRLSPVC Insulated unsheathed copper conductor 2.5 SQUARE METREm nominal cross section area as earth continuity conductor upto common earth and connecting to common earth dolly complete and including cutting/chasing of wall complete all as specified and directed by Engg. in charge. |
| 204 | Material and labour for Point wiring using approved colour coding as per IS with stranded copper conductor 4 SQUARE METREm (nominal area ),single core ,FRLS PVC insulated and unshaethed stranded cable 1100 volts grade ISI-694 marked TECand FIA approved in and including heavy duty ,PVC concealed conduit ISI marked for one industrial type metal clad earth plug and socket out let with earth dolly including FRLSPVC Insulated unsheathed copper conductor 4 SQUARE METREm nominal cross section area as earth continuity conductor upto common earth and connecting to common earth dolly complete and including cutting/chasing of wall complete all as specified and directed by Engg in Charge. |
| 205 | Supply and fix Modular Switch one way 6Ampsone module ISI Marked complete all as specified and directed by Engg in Charge. |
| 206 | Supply and fix Modular Switch one way 16Ampsone module ISI Marked complete all as specified and directed by Engg in Charge. |
| 207 | Supply and fix Modular Switch Two Way6 Ampsone module ISI Marked complete all as specified and directed by Engg in Charge. |
| 208 | Supply and fix Modular Bell Push6 Ampsone module ISI Marked complete all as specified and directed by Engg in Charge. |
| 209 | Supply and fix Modular Socket 6 Amps 5 Pin2 Module complete all as specified and directed by Engg in Charge. |
| 210 | Supply and fix Modular Socket 6/16Amps 6 Pin2 Module complete all as specified and directed by Engg in Charge. |
| 211 | Supply and fix Modular fan Regulator step type2 module complete all as specified and directed by Engg in Charge. |
| 212 | Supply and fix Modular Blanking Plate 1 module complete all as specified and directed by Engg in Charge. |
| 213 | Supply and fixModularTV Socket RJ-11 complete all as specified anddirected by Engineer-in-Charge. |
| 214 | Supply and fix Modular Telephone Socket RJ-11 complete all as specified anddirected by Engineer-in-Charge. |
| 215 | Supply and fix Ceiling rose surface backlite 65 x 20mm size three teRUNNINGMETREinal ISI marked complete all as specified and directed by Engineer-in-Charge |
| 216 | Supply and fix Electric buzzer AC,ding-dong type, 230 Volt, single pole complete all as specified and directed by Engineer-in-Charge |
| 217 | Material and labour for Taking down old and unsrevicablesheet metal enclosure , switch fuse unit , distribution bord any type /way / capacity including fuses,MCB\"s , insulator etc complete after removing all connection and making good the disturbed surface complete all as specified and directed by Engineer-in-Charge. |
| 218 | Supply and fix Sheet metal enclosures with TWO Pinandearth plug sockets controlled by one No.MCB DP rating 20 Amps , 415 Volts grade, complete all as specified and directed by Engineer-in-Charge. |
| 219 | Supply and fix Vertical sheet metal enclosures fordistribution boardTPN 4 way, 415 Volts, sheet metal powder coated, IP 43 protection with 200 Amps rated bus bar, double door type,grouted in wall in cement mortar, including MCCB, 415 volts, 4 pole, TPN Microprocessor based, fixed type rating 125 Amps, 16 KAas incomer complete all as specified and directed by Engineer-in-Charge. |
| 220 | Supply and fix Sheet metal enclosure MCB DB, SPN, 240 volts, 16 way, with 200 Amps Rated bus bar double door type grouting in wall in CM, making good of disturbed surfaces and matching with existing and electrical connections complete all as specified and directed by Engineer-in-Charge. |
| 221 | Supply and fix Sheet metal enclosure MCB DB, SPN, 240 volts, 8 way, with 200 Amps Rated bus bar double door type grouting in wall in CM, making good of disturbed surfaces and matching with existing and electrical connections complete all as specified and directed by Engineer-in-Charge. |
| 222 | Supply and fix MCB SP, 220volt , 50 Hzs, 6 to 32 A, 10 KA , \"C\" series complete all as specified anddirected by Engineer-in-Charge. |
| 223 | Material and labour for Taking down ceiling fan /exhaust fan, sealing cable end, dismantling blades and removing fan, any size or any type complete all as specified anddirected by Engineer-in-Charge.Note : All Ceiling fan/Exhaust fan shall be deposited to concerned AGE E/M for repair if required. |
| 224 | Hanging only ceiling fan (M.D supply) in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 SQUARE METREm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified anddirected by Engineer-in-Charge. |
| 225 | Fixing only exhaust fanin any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 SQUARE METREm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified anddirected by Engineer-in-Charge. |
| 226 | Painting to ceiling fan by spraying using synthetic enamel paint in two coats after cleaning all dust etc. , scraping of old paint , washing with washing powder water, refilling all type of cavities with filler and marking/ numberingas per existing complete all as specified anddirected by Engineer-in-Charge.Note : Colour for paint shall be approved by Engr-in-charge. |
| 227 | Painting to exhaust fan by spraying using synthetic enamel paintin two coats after cleaning all dust etc. , scraping of old paint , washing with washing powder water, refilling all type of cavities with filler and marking/numbering as per existing complete all as specified anddirected by Engineer-in-Charge.Note : Colour for paint shall be approved by Engr-in-charge. |
| 228 | Material and labour for Taking down old unserviceable meter anddepositedto concrned Maintance AGE E/M store and refixing the same after competion of complete work complete all as specified anddirected by Engineer-in-Charge. |
| 229 | Supply and fix LEDbulb 9 watt, 230 volt AC, 50 Hz, Retrofit, B22 base for lamp holder and including lamp holder suitable for batton fitting insulated body with back plate complete all as specified anddirected by Engineer-in-Charge. |
| 230 | Supply and fix Tube light fitting ,1x18/20 W LED 230 V, energy efficentbatten fitting, with driver etc complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible cable copper conductor including 18/20 watt LED tube rod complete all as specified anddirected by Engineer-in-Charge. |
| 231 | Supply and fix 10W Bulk head LED luminaries Die cast aluminium alloybody ,heat resistent prismatic glass cover ,with specially designed gasket incl all accessories & fixtures,internally prewired and connecting by provding copper flexible wire 23/.0076 mm twin core upto fitting, complete in all respects complete all as specified anddirected by Engineer-in-Charge. |
| 232 | Supply and fix Wall mounted decorative LED 12W luminaire complete all as specified anddirected by Engineer-in-Charge. |
| 233 | Supply and fix Surface mounted wall Mirror LED lightCompact & sturdy 10 watt LED decorative fixture with anti glare polycarbonate diffuser, multi purpose lighting solution & applications .all accessories & fixtures,internally prewired and connecting by provding copper flexible wire 23/.0076 mm twin core upto fitting, complete in all respects complete all as specified anddirected by Engineer-in-Charge. |
| 234 | Material and labour for Taking down old and unserviceable sub main wiring any size / type / core incl earth wire complete with batten/conduit etc and making good the disturbed surface to match the existing disturbed surface complete all as specified anddirected by Engineer-in-Charge. |
| 235 | Material and labour for Sub main wiring with two runs of 10 SQUARE METREm for phase and neutral, 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor ,drawn through and including non-metalic PVC rigid conduitISI marked with all conduit accessories conceiled in surface of walls/floors / ceiling etc with 1x6 SQUARE METREmsingle core FRLS PVC insulated unsheathed with one copper conductor as earth wire complete and including cutting/chasing of wall complete all as specified and directed by Engineer-in-Charge. Note:-2 runs of 10 SQUARE METREm cable,one run of 6 SQUARE METREm cable and one run of conduit will bemeasured together as one running meter. |
| 236 | Material and labour for Sub-main wiring with 2 single core flame retardant PVC insulated and unsheathed cable with stranded copper conductor of 6 Sq mm drawing in & including heavy grade FRLS PVC Concealed conduit ISI marked of suitable size ith all accessories onwallsand making good of disturbed surfaces including all conduit fittings, clamps, gutties etcand one additional 1 run of wire of 6 Sq mm but green in colour for earth DBs and boxes with proper thimbles complete and including cutting/chasing of wall complete all as specified anddirected by Engineer-in-Charge.Note:- 3 runs of 6 SQUARE METREm submain wiring and PVC Conduit will bemeasured together as one running meter |
| 237 | Material and labour for Taking up/down in trenches old unserviceable cable any type/any size complete all as specified anddirected by Engineer-in-Charge.Note: Excavation and earthwork will be measured and paid for seperately |
| 238 | Supply and laying XLPE insulated, screened, PVC bedded, galvanised steel strip or wire aRUNNINGMETREoured, electric cables (heavy duty) stranded aluminium conductor including cable glands, cable lugs etc , to suit the cable size, 1100 volt grade, ISI marked,laid in trenches or fixing along the poles or passing through the pipes or laid under floors or through walls/ducts etc. complete all as specified anddirected by Engineer-in-Charge of following cross sectional area :-NOTE: Excavation, earth work, sand cushioning, cable cover & pipe for cable protection will be measured and paid for separately. |
| 239 | (a) Cross sectional area 35 sq. mm, 3.5 core |
| 240 | (b) Cross sectional area 6 sq. mm, 2 core |
| 241 | Material and labour for Sand cushioning to cables with a layer sand 8 cm deep before laying the cable and 15 cm depth (punned down to 18 cm depth after laying and stretching of cable) including consolidation etc. complete all as specified anddirected by Engineer-in-Charge.Note:- Punned quantity of sand shall be measured for the purpose of payment |
| 242 | Material and labour for Bricks common burnt clay building bricks, sub-class ‘B’ designation 75 Old size bricks laid dry and flat adjecent to EACH other for brick protection cover on cable complete all as specified anddirected by Engineer-in-Charge. |
| 243 | Steel water tubing, galvanised, light grade, ISI marked,40 mm bore with and including all fittingslaid in trenches, on pole, under road, on wall, under floor etc. for protection of cable complete all as specified and directed by Engineer-in-Charge. |
| 244 | Material and labour for Taking down water heater any type/ size / capacity with all acessories after removing of all connections complete.Note: All Geysers shall deposited to concerned maintanance AGE E/M store for repair if required complete all as specified and directed by Engineer-in-Charge. |
| 245 | Material and labour for Refixingwater heater any type and any size/capacity with and including all accessories such as nut bolt washers , PVC pipe etc with making all connectionusing three core copper conductor flexible cable drawn through in PVC flexible conduit pipe including painting with two coats of super enameled paint of existing shed complete all as specified and directed by Engineer-in-Charge. |
| 246 | Supply and fix DecorativePost top lanternLED luminaire with diffuser and painted spun aluminium deflector fitting 40 W with clear acrylic cover complete all as specified and as directed by Engineer-in-Charge. |
| 247 | Supply and fix LED surface mounted, round panel with aluminium die cast housing 12 W incl all fixing accessories and connection complete all as specified and as directed by Engineer-in-Charge. |
| 248 | Rigid non-metallic PVC conduit exclusive of boxes (junction/teRUNNINGMETREinal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks of external dia size 20 mm , including cutting/chasing of wall complete all as specified anddirected by Engineer-in-Charge. |
| 249 | Supply and fix Junction box of size 150x150x150mm, made out of 2.0mm thick MS sheet, having front openable and locable hinged shutter with self closing arrangmenet, outdoor type weather and veRUNNINGMETREin proof completed duly painted with two coats of silver enameled paint over a coat of red oxide primer, comprising with insualted aluminium bus bar 04 Nos single phase 230 Volts of size 20x3 mm mounted on porcelain basedinsulators, having arrangement of connecting incoming and outgoing cables in and including MCB SP \"C\" curve 06 Amp, 240 Volts, 10 KA mounted on Din rail, thimbles etc.with suitable size of cable glands and MS clamps, nuts, bolts and washers complete all as specified and directed by Engineer-in-Charge. |
| 250 | Material and labour forEarthing complete with and including galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm surrounded by a mixture of charcoal and salt in alternate layers burried directly in ground vertically in a pit of depth not less than 2.25 m deep below ground level with top edge of earth plate at a depth of not less than 1.5 m below ground level, connected with and including galvanised iron or steel earth wire, 4mm dia (No. 8 SWG) by means bolts, nuts, check nuts and washers made out of galvanised iron, 15 mm bore GI pipe (light grade)for protection of earthing lead, 20 mm bore (medium grade) GI pipe for watering with funnel, wire mesh and including necessary excavation and earth work, PCC 1:2:4 type B-1 in pit base and 50 mm thick RCC 1:2:4 type B-1, reinforced with XPM (weight not less than 3 KILOGRAM/sq m) pit cover, C.I frame, charcoal and comman salt filling in alternate layers, complete all as shown and specified in electrical plate No. 3 of SSR Part-I (2009) complete all as shown on drawings and as specified and directed by Engineer-in-Charge.Note : The unit rate includes for protecton pipe 15mm and GI earth wire 4mm from top of earth plate upto 7.50 metre above ground level. |
| 251 | Supply and fix MCB SP, 230volt , 50 Hzs, 40 to 63 A, 10 KA , \"C\" series complete all as specified anddirected by Engineer-in-Charge. |
| 252 | Supply and fix Ceiling fan complete with electronic type regulator and accessories 230 V, 50 Hz, 1200 mm sweep. ConfoRUNNINGMETREing to IS-374-2019, complete all as specified anddirected by Engineer-in-Charge. |
| 253 | Supply and lay Steel water tubing, galvanised, medium grade, ISI marked, 50 mm bore with and including all fittings laid in trenches, on pole, under road, on wall, under floor etc. including taking down existing complete all as specified and directed by Engineer-in-Charge. |
| 254 | Supply and lay Steel water tubing, galvanised, medium grade, ISI marked, 25 mm bore with and including all fittings fixed to walls and ceilings or laid in trench, under floor etc. including taking down existing complete all as specified and directed by Engineer-in-Charge. |
| 255 | Supply and fix Gun metal, globe or gate valves with iron wheel head screwed both ends, class II suitable for iron pipe and fixed for 50 mm boredia including taking down existing complete all as specified and directed by Engineer-in-Charge. |
| 256 | Supply and fix Gun metal, globe or gate valves with iron wheel head screwed both ends, class II suitable for iron pipe and fixed for 25 mm boredia including taking down existing complete all as specified and directed by Engineer-in-Charge. |
| 257 | Excavation in trenches in soft/ loose soil not exceeding 1.50 meter wide and notexceeding 1.5 mtr in depth for foundation etc or for shafts, wells, cesspits, manholes, pier hole etc, and not exceeding 10 SQUARE METRE on plan and getting out complete all as specified and directed by Engineer-in- Chrage |
| 258 | Returning filling in, including, spreading, levelling, watering and well ramming in layers not exc 25 cm thick, excavated soil in trenches complete as in soft/ loose soil, complete all as specified and directed by Engineer-in- Charge. |
| 259 | Removing surplus soil/ excavated material obtained from demolition to a distance exceeding 250 m but not exceeding 500 m and deposition where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge |
| 260 | Supply and fixing 240 V, 10 KA \"B\" curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 to 63 Amp, in the MCB DB complete with connection testing and commissioning. |
| 261 | Note:-Amount of credit ofRs. 296953.00 for retrieved materials is mentioned in Schedule of Credit Page No. 18 of tender documents in pdf form which will be deducted offline while acceptance of tender. |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
