|
| 1 | Taking down chowkhats or frames n.exc 1.50 Square Meter with shutters (without taking off shutters from the frames) complete all as specified and ditected. |
| 2 | Taking down chowkhats or frames exc 1.50 Square Metern.exc 4.00 Square Meterwith shutters (without taking off shutters from the frames) complete all as specified and ditected. |
| 3 | Taking down shutters of any description exc 1 Square Meter and not exc. 2 Square Meter each complete all as specified and ditected. |
| 4 | S&F for 30mm thick flush shutters, solid core construction, designer with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed. |
| 5 | Material and labour 30 mm thick 2nd class hard wood factory made Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) complete all as specified in SSR Part I. |
| 6 | S&F for Pressed steel door frame of size 105 x 60 mm, double rebated for doors made out of 1.25mm thick mild steel sheet including necessary fixing lugs, hinges lock strike plate etc, complete all as specified and directed. |
| 7 | S&F for Pressed steel door frame of size 125 x 60 mm, double rebated for doors made out of 1.25mm thick mild steel sheet including necessary fixing lugs, hinges lock strike plate etc, complete all as specified and directed. |
| 8 | Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specification & drawing as shown in SSR part II complete all as specified and as directed. |
| 9 | Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in frame at site as per specification & drawing as shown in SSR part II, complete all as specified and as directed. |
| 10 | Dismantling block board/ boarding of any description and in any position complete including iron mongries complete all as specified. |
| 11 | Supply & fix 18 mm thick PVC board one side prelaminated and other side plain white colour as in cup board shutters and frames, kitchen cabinet frontshutter, partion, shelf, & drawer, fixed with screws, solvent cement / adhesive complete all as specified and directed by the Engineer-in-Charge. |
| 12 | Supply & fix 18 mm thick PVC board both side plain white colour as in cup board shutters and frames, kitchen cabinet frontshutter, partion, shelf, & drawer, fixed with screws, solvent cement / adhesive complete all as specified and directed by the Engineer-in-Charge. |
| 13 | Supply & fix 6 mm thick PVC board both side plain white colour as in cub board selves etc fixed with screws, salvent cement/ adhessive , complete all as per specifications & directed by Engr-in-Charge. |
| 14 | Supply and Fix Hasp and staple 100mm safety type, stainless steel 304 grade with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and ditected. |
| 15 | S&F for Continuous (PIANO) hinges, mild steel, bright finish or electrogalvanised 30 mm width of flaps (when open) complete all as specified as directed. |
| 16 | Supply and Fix factory made steel windows with side hung shutters including box type hinges with MS handles and tower bolts complete with glazing bars dovetailed or welded with one shop coat of primer complete all as specified and directed. |
| 17 | Supply and Fix factory made steel windows with side hung shutters including box type hinges with MS handles and tower bolts complete without glazing bars, as fly proof shutters with one shop coat of primer complete all as specified and directed. |
| 18 | Taking down existing projected type hings from the steel window carefully without disturbing frame and Supply and Fix 50 mm long mild steel box type hinge weld to steel frame and shutter with welding and making good including touch with paint and with existing surfaces including scaffolding all as directed by Engr-in-charge. |
| 19 | Supply and Fix butt hinges SS steel, medium weight 100 mm size with fixed complete all as specified and ditected. |
| 20 | Supply and Fix 150 mm long, solid in one piece stainless steelbarrel tower bolts complete all as specified and directed. |
| 21 | Supply and Fix 150mm size solid in one piece stainless steel handles,cast D type, fixed in stainless steel screwsall as directed complete all as specified and directed by Engr-in-Charge. |
| 22 | Supply and Fix 125mm size solid in one piece stainless steelhandles,cast D type, fixed in stainless steel screws all as directed complete all as specified and directed by Engr-in-Charge. |
| 23 | Supply and Fix 300mm long MS Helical door spring welded to steel frame or fixed to wooden door frame with screws including roller and roller plate etc complete all as specified and directed. |
| 24 | Supply and Fix floor door stopper of stainless steel double legged and tongue, 304 grade, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and ditected. |
| 25 | Supply and Fix stainless steel sliding door bolts 204 grade,hasp and staple typewith bright bolt not less than 12 mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 250mm long complete all as specified and ditected. |
| 26 | Hacking out old broken glass (any thickness, size, quality or description) from metal frame includingpunching or drilling out old glazing pins/spring clips and providingfixing new ones. |
| 27 | M & L sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc 0.5 Square Meter each pane all corner of glass to be fixed with silicon complete all as specified and directed by Engr-in-Charge. |
| 28 | Supply and Fix 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each pane complete all as specified and directed. |
| 29 | Supply and Fix Stainless steel 304 grade wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples with 8% nickle complete all as specified and ditected. |
| 30 | Supply and Fix in repair 20 mm dia stainless steel polished 204 grade drapery rod 1mm thick with final decorative, including brackets, decorative finished at both ends completeall as speccified and directed as per approved sample complete all as specified and ditected. |
| 31 | M&L for 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar work/places, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement and Demolition of cement concrete ground floor and paving nexc 15cm thick (below or above ground level) and dispose with in the MD land 1.5kmcomplete all as specified and directed. |
| 32 | M&L for glazed ceramic colour tiles size 300 mm x 450 mm/ 300 mm x 600mm x 6-7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 and dismantling of existingwall tiling including cement mortar bedding (but not backing) andrubbish off the premisescomplete all as specified and directed. |
| 33 | M&L for non skid/mat finish ceramic colour tiles of size 300 mm x 300 mm and 7 to 8 mmthick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed. |
| 34 | M&L for non-skid / mat finish designed coloured joint free ceramic tiles of size not less than 400 mm x 400 mm x 6-7 mm thick in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 and dismantling of existing tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed. |
| 35 | All as per item No 22 here in above but as in skirting and including 10 mm thick rendering in cement mortar 1:4,complete all as specified and directed. |
| 36 | M&L for heavy duty antiskid parking coloured tiles 9-10 mm thick dark shade (square/rectangular) polished area of each tiles not exceeding 0.36 sqm, in floor etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified. |
| 37 | Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for complete all as specified and as directed. |
| 38 | M&L for coloured pre-polished rubber moulded chequred cement concrete tile 300mm x 300mm x 20-22mm thick with anti skid properties set, jointed and pointed in neat cement slurry as in floor with grey cement and pigmentlaid over and including 15 mm thick screed bed in CM 1:6 completeall as specified and as directed. |
| 39 | M&L for 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and directed. |
| 40 | M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in leveling course to floors complete all as specified and directed. |
| 41 | Demolition of Stone slabs and tiles laid, bedded in any mortar of any description or thickness in floors, aprons etc complete all as specified and ditected.. |
| 42 | Supply and Fix granite 20mm thick of any type ( table rubbed and polished in steps, jambs pillars, window cill, cooking platfoRunning Meter and like in cement mortar 1:4 incl pointing in white cement complete all as specified and ditected. |
| 43 | Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concretebut excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and ditected. |
| 44 | M & L Brickworkwith subclass `B\" bricks, straight or curved on plan exc 6m mean radius, built in Cement Mortar 1:4 complete all as specified |
| 45 | M & L for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:6, surface finished even and smooth (without using extra cement) ,including Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc including scaffoldingcomplete all as specified and directed. |
| 46 | M & L for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4, surface finished even and smooth (without using extra cement) ,including Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etcincluding scaffolding complete all as specified and directed. |
| 47 | M & L for 10 mm thick rendering on celing surface in cement mortar 1:3mixed surface finished even and smooth,including Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etcincluding scaffoldingcomplete all as specified and directed. |
| 48 | M&L for preparation of newly plastered surface of walls including corners and applying two coats ofdistemper oil emulsion over applying of 1-1.5 mm thick wall care putty finish wall surface even & smooth all as specified and directed. |
| 49 | M&L for two coats of exterior grade 1st quality weather coat paints over a coat of alkali resistant priming paint including preparation of new plaster external surfaces of wall etc, with scrap wire brush and washing with waterover applying of 1-1.5 mm thick wall care putty finish wall surface even & smooth complete all as specified and directed. |
| 50 | M&L for preparation of newly plastered surface on ceilings and applying three coats of white wash on ceiling, off sets, pillar etc. all as directed and specified. |
| 51 | M&L for complete removal of existing treatment of walls including corners and applying two coats ofdistemper oil emulsion over applying of 1-1.5 mm thick wall care putty finish wall surface even & smoothall as specified and directed. |
| 52 | M&L for complete removal of existing treatment on ceiling and applying three coats of white wash on ceiling, off sets, pillar etc all as directed and specified. |
| 53 | M&L for complete removal of existing treatment of walls including corners and applying twocoat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqmover applying of 1-1.5 mm thick wall care putty finish wall surface even and smooth complete all as specified and directed. |
| 54 | M & L applying two coats of Synthetic enamel paint on newwooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed. |
| 55 | M & L preparation of old painted surfaces of wood of any description over 10 cm width or girth and applying one coat of synthetic enamel Paint complete all as specified and directed. |
| 56 | M & L applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed. |
| 57 | M & L applying one coat of synthetic enamel paint on old painted steel surfaces/concrete surfaceof any description including preparation of steel surfaces complete all as specified and directed. |
| 58 | S&F for 15 mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor including taking down of old unserviceable pipes complete all as specified and directed by Engr-in-Charge. |
| 59 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F for 20 mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor including taking down of old unserviceable pipes complete all as specified and directed by Engr-in-Charge. |
| 61 | Supply and Fix CP brass long bodybib tap 15mm bore screwed for iron pipe or for brass ferrule complete all as specified and ditected. Make-Cera/Parryware/Hindware. |
| 62 | Supply and Fix in repairs CP stop/angle cock fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed |
| 63 | Supply and Fix in repair CP brass shower rose 15mm dia , 100mm dia complete all as specified and directed. |
| 64 | Supply and Fix in repair 10 Litr Dual capacity PVC low level flushing cistern including PVC syphon and float valve withPVC long bend for out let, fixing with WC complete all as specified and directed by Engr-in-charge |
| 65 | Supply and Fix in repairsPVC connection 15mm size with PTMT nuts, of 450 mm long complete all as specified and ditected. |
| 66 | Supply and Fix rotational moulded polyethylene 500 Ltrs Capacity water storage tanks(cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float three layer external and internal white and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and ditected. |
| 67 | Supply and Fixin repair viterous china squatting pan (orissa pattern) long pan size 580x440mm white with integral footrest with cast iron spun 600 mm long \"P\"trap (SI 3989 1984), set in cement concrete type B-1 (1:2:4) complete (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in-charge. |
| 68 | Supply and Fix in repairs 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers as approved by Engr-in-Charge. |
| 69 | Supply and Fix in repairs 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified. |
| 70 | Supply and Fix in repairs Soap dish 6 inches, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 71 | Taking down CI/AC/PVC pipes incl fittings upto 110/75mm dia and removing from site complete all as specified and directed. |
| 72 | Supply and Fix PVC (SWR) pipes of 110 mm dia, single socketed fixed to walls complete all as specified and directed. |
| 73 | Supply and Fix PVC (SWR) pipes of 75 mm dia, single socketed fixed to walls complete all as specified and directed. |
| 74 | Supply and Fix PVC (SWR) bends of 110 mm dia, any radius complete all as specified and directed. |
| 75 | Supply and Fix PVC (SWR) bends of 75 mm dia, any radius complete all as specified and directed. |
| 76 | Supply and Fix PVC (SWR) junction single Tee equal or unequal 110 mm dia complete all as specified and directed. |
| 77 | Supply and Fix PVC (SWR) junction single Tee equal or unequal 75 mm dia complete all as specified and directed. |
| 78 | Supply and Fix PVC(SWR) floor trap, plain with grating including jointed with solvent cement of 75 mm outlet dia complete all as specified and directed. |
| 79 | Supply and Fix in repairs 32 mm bore heavy duty waste pipe not less than 60cm long with PVC coupler for kitchen sink, WHB, urinal, etc complete all as specified and directed by Engr-in-Charge. |
| 80 | Supply and Fix in repairs for 75/110mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof complete all as specified and directed. |
| 81 | Supply and Fix in repair sink coupling 32mm dia PTMT half or full threaded complete all as specified and directed by Engr-in-Charge. |
| 82 | Supply and Fix in repair CP steel Grating round with steel frame with hinge 100mm dia all as sample approved by Engr-in-charge. |
| 83 | Material and Labour for taking down existing roof treatment of felt etc any thickness or description including cleaning all upto roof slab incluing removing spoil former site and Material and Labour for providing roof treatment as per the following steps :-i) Filling cracks of roof slab with approved chemical sealing compound and applying 15mm thick renedering in CM 1:4 over neat cement slurry @ 3.00 Kilogram/Square Meter over cleaned roof surface with use of approved water proofing compoung. ii) Applying a coat of cold applied bituminous primer @ 0.30 Kilogram/Square Meter followed by APP modified five layer polymeric membrane 3mm thick, minium weight 3.60 Kilogram/Square Meter reinforced with plyester non-woven fabric (weight not less than 150 gms/Square Meter) manufactured by M/s STP Ltd or M/s Texsa India Ltd, laid as per the manufacturers instruction with side over lap of 75mm and end over lap of 100mm and finally finished with super silver sheild @ 0.10 Ltr/Square Meter. Note : The work of water proofing treatment shall be got executed thorugh manufacturer or authorised applicator only. |
| 84 | Supply and Fix in repair plate rack 300mm and size 100 x 80 cm made out of 1.00 mm thick stainless steel complete all as specified and as directed. |
| 85 | Supply and Fix in repairs stainless steel kitchen sinks without draining board ISI marked made of stainless steel 1 mm thick, with plugs, washers and wastes, including bedding lime cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified. |
| 86 | Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high Writing bldg No all as specified and directed by Engr-in-Charge. |
| 87 | Material and Labour 65-70mm for reinforced precast cement concrete 1:1:2with 1.25mm thick MS sheet painted with bituminous paint around the manhole cover (using 20mm graded stone aggregate) as in landings, cover slabs ( for manholes etc.) vibromatic, articles with plain faces including necessary former work using surface vibrator, complete CA No and date of casting to be engraved on the cover slab by stencil and curing will be done in the water resveriorall as specified and directed. (Reinforcement shall be measured and paid for separately under respective item of schedule \"A\"). |
| 88 | Supply and Fix TMT MS bar 8 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia complete all as specified and dircted. |
| 89 | Material and Labour for Removing /cutting trees vegetation, digging out roots from concrete or brick wall filling holes on building (block of 12qtrs ) wall/roof/cajja/water tank staging area etc and making good with cement mortar 1:2:4 complete. |
| 90 | Material and Labour for cement concrete in 1:2:4 type B-2 (40 mm graded aggregate ) as in surface channel and drain complete all as specified |
| 91 | M & L for 20 - 25 mm thick machine cut Kota stone slab as in flooring over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing, rounding to exposed edges incl 20 mm thick screed bedding layer of CM 1:4 complete all as specified and directed. |
| 92 | Taking out old damaged SGSW pipes from existing lines including necessary excavation in trenches and getting out in any type of soil, supply, laying and jointing of PVC pipe of 150mm dia including packing under and haunching against the sides of pipes in PCC (1:4:8) type D-2 and returning, filling in disposal of surplus soil to a distance n exc 50m complete all as specified and directed by the Engr-in-Charge.. |
| 93 | Excavation in post holes (or similar holes ) in any type of soil each n exe 0.5 cum , gettting out, returning, filling in and ramming earth or broken rubble mixed with earth around , in layers not exeeding 25cm, watering, and removing surplus soil to a distance n exe 50 m and making good surface all as specified. |
| 94 | M&L for cement concrete type C-2 1:3:6 (using 40mm graded aggregete as in foundation and mass concrete as specified and directed. |
| 95 | S&F in repair powder coated Aluminium standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter and one noswire gauged shutter sliding type, with aluminum sections as per Series-A(15mm) 3 track of Jindal section numbers for sliding windows,and glazed with glass 5mm thick, fixed with glazing clips, aluminium grill with mesh size 75 mm and aluminium bar 6 mm XPM type, rubber beading / gasket anodised beading, screw and lock type handle of size 75mm, 2 Nos aluminum tower bolt 150mm long etc, complete all as specified and directed by Engr-in-charge. Shutter Top & bottom size:- 37.50 x 15.00 x 1.60 mm Shutter inner lock size:- 37.50 x 15.00 x 1.60 mmShutter side (Handle) size:- 37.50 x 15.00 x 1.36 mmChowkhat bottom size:- 50.30 x 26.00 x 1.20 mm Chowkhat top & sides size:-50.30 x26.00 x 1.00 mm |
| 96 | Dismantlingwrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 97 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including dismantlingwrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 98 | S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed. |
| 99 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed. |
| 100 | S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to walls etc fixed with self tapping screws as specified |
| 101 | M&L for taking down of existing sunken slab treatment from the sunken portion and cleaning the surfaces washing down with water and rubbish of the premises, cleaning and filling cracks with sealing compound, brushing neat cement slurry @ 3.00Kg/Sqm and gouting 25mm thick cement concrete type B-0 (1:2:4) (using12.5mm graded stone aggregate) on sunken slab portion and finishing the top surfaces even and smooth without using extra cement . (b) M&L for two coat of acrylic cementitious water proofing coating (Dr FIXIT pidifin 2K manufactured by M/S Pidilite Industries Ltd or equivalent) and followed by a overlay protective screed (15mm thick CM 1:3 alongwith liquid water proofing compound approved make) on top surfaces of sunken slab after preparations as mentioned above method of application for acrylic cementitious water proofing coating is followed as per manufactures instructions complete all as specified and directed. |
| 102 | Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge. |
| 103 | M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia or higher and heavy grade conduit fittings and heavy duty accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.6mm thick for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of following. Note: The wiring to be done as per IE rule and maintain colour code accordingly. |
| 104 | One light point point /bell buzzer point controlled by one-one way switch. |
| 105 | One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator. |
| 106 | One three pin 5 Amp socket on same board with other switches. |
| 107 | One three pin 5 Amp socket on independent board |
| 108 | All as per item No 103 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 1.5 Sq mm. |
| 109 | M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in existing PVC / Steel concealed conduit, and MS boxes/ cast iron or pressed steel terminal box 1.6mm thick for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge. Note:The wiring to be done as per IE rule and maintain colour code accordingly |
| 110 | One light point point /bell buzzer point controlled by one-one way switch. |
| 111 | One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator. |
| 112 | One three pin 5 Amp socket on same board with other switches. |
| 113 | One three pin 5 Amp socket on independent board |
| 114 | One light point controlled by two way switch |
| 115 | All as per item No 109 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 1.5 Sq mm. |
| 116 | S&F switch piano flush, button type 5 Amp SP 250 V AC complete all as specified & directed. |
| 117 | S&F switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed. |
| 118 | S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed. |
| 119 | S&F socket outlet two in one three pin 5 Amp and 15 Amp 2 module 120 W flush type complete al as specified. |
| 120 | S&F Bell switch paino flush button type 5 Ampcomplete all as specified. |
| 121 | S&F ding dong bell AC 230 V single pole complete all as specified and directed . |
| 122 | S&F switch paino flush button type 5 Amp SP 2 way complete 250 V AC all as specified and directed. |
| 123 | S&F step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts 6 Ampds 400 watts. |
| 124 | S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC. |
| 125 | M&L lamp holder insulated body with back plate suitable for angle and batten fitting complete all as specified. |
| 126 | M&L sub main wiring with 2 Single core PVC insulated unsheathed FRLS cable 1100 Volts grade heavy duty copper conductor multistranded of size 10 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higherPVC concealed conduit heavy duty accessories and fittings. PVC insulated unsheathed FRLS cable copper conductor multistranded of size 10 Sq. mm. as earth wire upto common earth and connected to earth dolly complete all as specified & directed. |
| 127 | S&F sheet metal enclosures 240 voltwith 200 Amp rated bus bar for double door 8 way DB,sIP-43 IK 09 metal door suitable for one MCB SPN as incoming and 06 MCB SP as out going complete all as specified and directed |
| 128 | S&F MCB double pole 240 Volt 10 KA 40 Amp \"B\" series conforming to ISI marked complete all as specified & directed |
| 129 | S&F MCB single pole and240 volt 10 KA 5-32 Amp \"B\" series conforming to ISI marked all as specified and directed |
| 130 | S&F MCCB 415 Volt 16 KA 4 pole 125 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed. |
| 131 | S&F in replacementwall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make: Philips cat part NoTMC 501P1xT LED 22WP-3241(Tube Batten) and MAS LE$D 1200mm 18W-865-T-81 (Tube) / Wipro Cat part No WI0922208(Tube Batten) LL13-181-65SE (Tube)/ Havells Cat Part No LUMILINEPLUSBS20WLED865SPCSS (Tube Batten)CRYSTAL1213T8DSTL20WLED865SGLASS(TUBE DOUBLE SIDE) |
| 132 | S&F mirror light with high out put diffuser 2 feet, 10 watt 220 V AC decorative type compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size . |
| 133 | S&F in replacementLED light fitting decorative wall mounting SS brush finish fixture with frosted glass suitable for upto 1x40 watt mini glass lamp with and including one no 12 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size. |
| 134 | S&F in replacement of ceiling fan 1200 mm sweep single phase 230 volts double ball bearing with down rod , canopy, blades etc BEE 5 star rated including connecting with twisted three cord flaxible copper conductor cable (23/.0076 ) from ceiling rose toconnector of fan comlete all as specified and directed (Note: Old unserviceable ceilingfan will be deposited in E/M store yard. ) |
| 135 | S & F high efficiency LED bulbs 1 X 12 watt that can be used as a ready replacement for existing GLS ad CFL direct fit in holder complete all as specified and directed. |
| 136 | Supply and FixingIntegral LED Bldg security Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 40/45wattwith efficiency100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours, complete all as specified and directed. |
| 137 | M&L for stone/brick wall cutting in circular shape, grouting or suitable bolts suitable for 300 mm exhaust fan and making disturbed surface good plastering and distempering etc complete all as specified and directed (Job). |
| 138 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm, 900 RPM, single phase, 230V AC with louver all as specified and directed 30 mm sheet. including connection with twisted white three core flexible copper multistranded conductor cabl from ceiling rose to connector all a directed by Engineer-in-charge. |
| 139 | S&F in replacement of Geyser vertical mount type 25 Ltrs capacity five star rated , shockproof and rust proof metal body compact size including two nos PVC connection heavy duty and connecting with all fixing arrangement of nuts & bolts and fixing on wall complete all as specified & directed ( Note: old unserviceable Geyser will be deposited in E/ M store yard ) |
| 140 | S & F PVC enclosure (Box) with plug and socket complete with one 240 Volts 20 amp single pole MCB complete all as specrified & directed. |
| 141 | M&L for Excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth for laying of underground cable, foundation of poleand getting out in soft/loose soil complete all as specified and directed. |
| 142 | M&L for Returning, filling in excavated soil in trenches including spreading, levelling, watering and well rammingin layers n. exc. 25 cm thick complete all as specified and directed. |
| 143 | M&L for Removing of excavated soil to a distance n. exc. 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed. |
| 144 | M&Lfor laying local dry clean sand filling for cushioning in trenches around under ground cable complete all as specified and directed. |
| 145 | M&L for laying well burnt brick, old size in trenches, as protection of under ground cable complete all as specified and directed. |
| 146 | Supply, laying, jointing and testing of undergroundXLPE insulated, armouredheavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area25 Sqmm 4 Core laid in trenches/ducts/along poles/through pipe under road etc with new aluminium lugs of cable sizeall as specified and directed. |
| 147 | Supply and laying galvanised steel tubing 50mm bore light grade laidin trenches or fixed to poles/walls etc for cable protection complete all as specified and directed. |
| 148 | Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edgeof the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized steel earth wire 4 mm dia by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1, cover slab54 cm x 54 cm x 5 cm reinforced with 8 mm dia.TMT bars @ 150 mm c/c both ways, and with one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil and necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009) and as directed. |
