|
| 1 | Taking down cement plastering of any description on brick / stone/ concrete wall / ceiling surfaces of any description incl racking out joints hacking for key, scrubbing down with water etc , complete all as specified and directed by Engineer-in-Charge. |
| 2 | M&L for rendering in cement mortar (1:6), 15mm thick on other than fair faces of stone masonary surfaces finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 3 | M&L 10mm thickrendering in cement mortar in CM (1:3) on ceiling finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 4 | M&L 5mm thickrendering in cement mortar in CM (1:3) on ceiling finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 5 | M&L 15mm thick rendering in cement mortar (1:4) mixed with water proofing compound @3% by weight of cement on fair faces of brick work or concrete surfaces, finished even and smooth , complete all as specified and directed by Engineer-in-Charge. (WPC measured and paid separately) . |
| 6 | M&L for rough cast plaster over 10mm thick cement plaster in cement mortar 1:4 on stone / brick masonary wall surfaces , complete all as specified and directed by Engineer-in-Charge. |
| 7 | Supply only integral water proofing compound, ISI Marked, complete all as specified and directed by Engineer-in-Charge. |
| 8 | M&L for preparation of newly plastered surface of wall and apply two coats of oil bound distemper over a coat of 1mm average thick wall care putty, complete all as specified and directed by Engineer-in-Charge. |
| 9 | M&L for preparation of newly plastered ceiling surfaces and applying two coats of white wash , complete all as specified and directed by Engineer-in-Charge. |
| 10 | M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of primer, complete all as specified and directed by Engineer-in-Charge. |
| 11 | Demolition ofbrick work or stone/boulder masonarybuilt in cement mortar of any specification and in any position , complete all as specified and directed by Engineer-in-Charge. |
| 12 | M&L for brick work with flyash old size bricks, straight or curved on plan exc. 6mm mean radius, built inin cement mortar 1:6., complete all as specified and directed by Engineer-in-Charge. |
| 13 | M&L for walling random rubble masonary uncoursed well bonded bedded and solidly hearted and built in cement mortar 1:6 etc , complete all as specified and directed by Engineer-in-Charge. |
| 14 | Demolition of cement concrete (unreinforeced) in ground floors and pavings n. exc 15cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge. |
| 15 | M&L for 75 mm thick PCC 1:3:6 type C2 using (40 mm graded crushed stone aggregate) as inplinth protection surface finished fair and evencomplete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) , complete all as specified and directed by Engineer-in-Charge. |
| 16 | M&L for 75mm thick cement concrete type D-2 1:4:8 (using 40mm graded stone aggregate) in sub base of flooring/ hard standing complete all as specified and directed by Engineer-in-Charge. |
| 17 | M&L for 50mm thick cement concrete type B-1 1:2:4 (using 20mm graded stone aggregate) as in of flooringwithout using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 18 | M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as inrounded or chamfered on edges in any description complete all as specified and directed by Engineer-in-Charge. |
| 19 | Dismantling Wall and ceiling boards/wall panelling(fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-Charge. |
| 20 | Providing & Fixingfalse ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross \"T\" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main \"T\" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross \"T\" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge. |
| 21 | Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed by Engineer-in-Charge. |
| 22 | M&L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 Sqm but not exc 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 , complete all as specified and directed by Engineer-in-Charge. |
| 23 | All as peritem No-22but in skirting over 10mm thick screeding in cement mortar 1:4 , complete all as specified and directed by Engineer-in-Charge. |
| 24 | M&L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 , complete all as specified and directed by Engineer-in-Charge. |
| 25 | M&L for Glazed ceramic tiles coloured (450x300mm) x 7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick backing coat of tiles in CM (1:4) complete all as specified and directed by Engineer-in-Charge. |
| 26 | M&L for vitrified ceramic tiles light shade 8-10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm not exceeding 0.36 Sqm, in floor etc set and jointed in neat cment slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 , complete all as specified and directed by Engineer-in-Charge. |
| 27 | M&L for vitrified ceramic tiles light shade 8-10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm not exceeding 0.36 sqm, in vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed plaster 10mm thick in CM 1:4 , complete all as specified and directed by Engineer-in-Charge. |
| 28 | M&L18-20 mm thick granite ( of any type ) work(table rubbed and polished) in steps, jambs, pillars window cills, cooking platform and like in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge. |
| 29 | M&L preparationof old plastered surface of wall and applying onecoat of distemper oil emulsion / oil bound distemper over coat of 1mm thick average thick wall putty, complete all as specified and directed by Engineer-in-Charge. |
| 30 | M&L for machine cut Kota stone slab flooring 18-20 mm thick over 15mm thick screed bed in CM 1:6,laid andjointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge. |
| 31 | M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab incl rubbing & polishing, complete all as specified and directed by Engineer-in-Charge. |
| 32 | M&L only on old surfacesmirror polishing on marble/granite/kota stone where ever required to give high gloss finish complete all as specified and directed by Engineer-in-Charge. |
| 33 | Refixing shutters of any description n exc 1 sqm each in same opening incl. taking down , complete all as specified and directed by Engineer-in-Charge. |
| 34 | Refixing shutters of any description exc 1Sqm but n. exc 2 Sqm each in same opening incl. taking down , complete all as specified and directed by Engineer-in-Charge. |
| 35 | M&L for chequered cement concrete tiles 25 x 25 cm x 22-25 mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigments over 15 mm screed bed in CM mortar 1: 6 , complete all as specified and directed by Engineer-in-Charge. |
| 36 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed by Engineer-in-Charge. |
| 37 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required , complete all as specified and directed by Engineer-in-Charge. |
| 38 | Taking down old unserviceable rolling shutter and S & F steel rolling shutters gear operated type with bevel gear box & crank handle, thickness of laths 1.25mm with ball bearing as specified including top cover, anchoring rod, hasp & staple and one shop coat of primer, errected in position as directed including making good disturbed surface to match the existing , complete all as specified and directed by Engineer-in-Charge. |
| 39 | S &F mild steel ball bearing suitable size for rolling shutter , complete all as specified and directed by Engineer-in-Charge. |
| 40 | S &F mild steel safety lever lock with 4 levers suitable size for rolling shutter , complete all as specified and directed by Engineer-in-Charge. |
| 41 | Taking down old unserviceable 15mm GI tubing, fittings and connections and removing from site or keeping aside for refixing, complete all as specified and directed by Engineer-in-Charge. |
| 42 | S&F 15mm bore, water tubing, medium grade, galvanised with all fittings and fixed to walls, ceiling or laid in floors / trenches , complete all as specified and directed by Engineer-in-Charge. |
| 43 | Hacking out old broken glass up to 9.50 m height (any thickness size, quality or description) from steel frames, glazed with putty or fixed with beads , complete all as specified and directed by Engineer-in-Charge. |
| 44 | S&F 3mm thick plain sheet glass ordinary quality and glazing with oil putty upto 9.50M height in steel shutter in square n.exc 0.50 Sqm in each pane or any steel frame including glazing clips, complete all as specified and directed by Engineer-in-Charge. |
| 45 | S&F 3mm thick frosted glass panes and glazing with oil putty & pins/spring pins complete in squares n.exc 0.50 sqm each panes , complete all as specified and directed by Engineer-in-Charge. |
| 46 | Dismantling asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified and directed by Engineer-in-Charge. |
| 47 | S&F 6mm thick asbestos cement corrugated or semi corrugated sheets in roof fixed with L-type or J-type or cranked hook bolts complete all as specified and directed by Engineer-in-Charge. |
| 48 | M&L asbestos cement two piece adjustable plain wing ridge 6 mm thick , complete all as specified and directed by Engineer-in-Charge. |
| 49 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws fixed with L & J hooks and washers, in roofs, walls etc with grade of zink coating 275 complete all as specified and directed by Engineer-in-Charge. |
| 50 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge. |
| 51 | Dismantling timber scantlings unframed 40 sqcm and over in section, in any position , complete all as specified and directed by Engineer-in-Charge. |
| 52 | S & F rolled mild steel as in angle setion, fixed indepenntly with or without connecting plates or welding with existing steel or iron surfaces etc and similar work confirming to Gde E-165 (Fe 290) including necessary cutting, welding etc and fixing in position , complete all as specified and directed by Engineer-in-Charge. |
| 53 | S&F steel work in tubular trusses, purlins, rafterincluding special shaped washer etc,complete using ERW or induction butt welded tubes , complete all as specified and directed by Engineer-in-Charge. |
| 54 | M&L for preparation of new steel and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer., complete all as specified and directed by Engineer-in-Charge. |
| 55 | Taking down chowkats with shutter (without taking off shutter from the frame)exc. 1.5 sqm & n. exc 4 sqm each , complete all as specified and directed by Engineer-in-Charge. |
| 56 | All as per item No-55but n. exc 1.5 Sqm each , complete all as specified and directed by Engineer-in-Charge. |
| 57 | M&L for aluminium powder coated door frame and shutter including top, bottom/middle rail using glazing clip including rubber head and float glass 6mm thick tinted provided with one floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steelheavy dutyfixed to aluminium door andother fittings like handle, locking system, push plate and necessary beading all around the door shutter frame as required for resistance , complete all as specified and directed by Engineer-in-Charge. and as per Chief Engineer Drg No CBZ/TD/05/2011 |
| 58 | M&L for aluminium powder coated sliding window, ventilator three track including aluminium powder coated decorated grill sliding shutter 5mm thick tinted float glasses, necessary aluminium beadings fittings and other panels to prevent air from out side , complete all as specified and directed by Engineer-in-Charge. and as per Chief Engineer Drg No CBZ/TD/15/2011 |
| 59 | S&F door closure hydraulically regulated designation No-3 universal type suitable for door shutter of 851 to 1000mm in width of aluminium body (die cast) weight between 61 to 80 kg in repair , complete all as specified and directed by Engineer-in-Charge. |
| 60 | S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers,etc , complete all as specified and directed by Engineer-in-Charge. |
| 61 | S&F brass knob 35-40mm dia fixed in repair , complete all as specified and directed by Engineer-in-Charge. |
| 62 | S & F in repairsSquatting pattern Water closet, Orissa pattern of vitreous chinna Size 580x440mm wide with integral foot rest etc , complete all as specified and directed by Engineer-in-Charge. |
| 63 | Supply and Fixing in repairs vitreous china wash downwater closetpedestal pattern pan whitewithtrap including connection to existing out joint pipe, flushing pipeor Cistern, antisyphonage pipe, including making, etc complete including making goood to floor etc complete all as specified and directed by Engineer-in-Charge. |
| 64 | Supply and Fixing in repair plastic water closet seat coverany colourclosed pattern with flat bottom and cover with mild steel chromium plated hinging device etc complete all as specified and directed by Engineer-in-Charge. |
| 65 | S & F in repairs grating round 125 mm dia PTMT minimum weight 50 gms fixed to Floor trap/Nahni trap with CM 1:6 etc , complete all as specified and directed by Engineer-in-Charge. |
| 66 | S&F in repairs 15mm bore cast copper alloy chromium plated bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge. |
| 67 | S&F in repairs PVC (SWR) floor trap plain with grating incl jointing with solvent cement of 75mm dia complete all as specified and directed by Engineer-in-Charge. |
| 68 | S&F in repair PVC low level flushing cisternsyphonic action typewhitewith inlet ball valve, handle including brackets10 ltrscapacity etc , complete all as specified and directed by Engineer-in-Charge. |
| 69 | S & F in repairs PVC connections 15mm size with PTMT nuts and bolts of length 450mm etc , complete all as specified and directed by Engineer-in-Charge. |
| 70 | S&F in repair angle valves 15mm bore , cast copper alloy chromium plated fancy type, screwed down high pressure screwed both ends for iron pipe or for unions and fixed etc , complete all as specified and directed by Engineer-in-Charge. |
| 71 | S&F in repair wash basins vitreous china, white /colouredflat back size 550 x400mm fixed including bracket , complete all as specified and directed by Engineer-in-Charge. |
| 72 | S&F in repairs 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls , complete all as specified and directed by Engineer-in-Charge. |
| 73 | S&F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls , complete all as specified and directed by Engineer-in-Charge. |
| 74 | S & F75mm bore PVC(SWR) bends with oval access door of any radius , complete all as specified and directed by Engineer-in-Charge. |
| 75 | S & F 110mm bore PVC(SWR) bends with oval accessdoor of any radius , complete all as specified and directed by Engineer-in-Charge. |
| 76 | Total in Figures |
| 77 | Quoted Amount in Words |
