Military Engineer Services-MES has published Tender For Special Repair To Bldg No. T-17, T-18 And T-19 In Adm Area At Yol Cantt. Submission Date for this Tender is 22-05-2024. Building Work Tenders in Kangra Himachal Pradesh. Bidders can get complete Tender details and download the document.
FileName | File Description | File Size |
7cfbd3cc-5a29-444d-beec-518c67263ede.html | Tender Notice | 0 KB |
BOQ_728699.xls | Tender Document | 0 KB |
E-tender12.pdf | Tender Document | 0 KB |
Tendernotice_1.pdf | Tender Document | 0 KB |
Sl. No. | Item Description |
1 | Demolition of cement concrete (unreinforced) in ground floor and pavingn.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed. |
2 | Demolition of reinforced cement concrete ((reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed. |
3 | Demolition of brick workor stonework built in cement mortar including allquoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed. |
4 | Taking down cement plaster including backing etc from brick/stone walls / concrete surfaces including raking out joints,hacking for key , scrubbing down with water etc complete all as specified and directed |
5 | Taking downand removing chowkats with shutters (withouttaking off shutters from chowkat)not exceeding 1.50 Sqmeach complete all as specified and directed. |
6 | Taking down and removing chowkats with shutters (withouttaking off shutters from chowkat)exc 1.50 Sqmbut not exc 4.00 Sqm each complete all as specified and directed. . |
7 | Dismantlingtimber in scantling 40 sqcm and over in section, framed work complete all as specified and directed. |
8 | Dismantlingtimber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, framed work complete all as specified and directed. |
9 | Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. |
10 | Dismantling plain or corrugatedsteel sheetsany gaugethickness including Nanital or similar pattern roof covering including ridges complete all as specified and directed. |
11 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises. complete all as specified and as directed. |
12 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed. |
13 | Dismantling boarding, any description, fixed in any position with nailscomplete all as specified and directed. |
14 | Plain cement concrete 1:2:4 ( nominal mix ) type B-0 (using12.5mm graded crushed stone aggregates) as in cement concrete in roof kerbs or mud stops, rounded or chamfered on edges, lintels upto 1.5m clear span, cills, steps; seismic and othersimilar ands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating,includingnecessary formwork where required complete all as specified and directed. |
15 | PCC 1:3:6 (nominal mix) type B-2(using 40mm graded crushed stone aggregates) as in surface channel and drains including necessary form work complete all as specified and directed. |
16 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex tra cement, including forms, moulds, mi- tred/stopped ends etc. all as specified and as directed. |
17 | RCC M-25(Designmix)(using 20 mm graded crushed stoneaggregates ) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
18 | RCC M-25 (Designmix)(using 20 mm graded crushed stoneaggregates ) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
19 | Use & waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete, complete all as specified & directed. |
20 | Use & waste of form work to suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces of flat concrete, complete all as specified & directed. |
21 | Brick work with old size fly ash bricks, class 7.5, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:6 all as specified & directed. |
22 | Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 all as specified & directed. |
23 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as shown on page No176 to 183 of MES SSR 2020 Part-II compete all as specified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) |
24 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as shown on page No176 to 183 of MES SSR 2020 Part-II compete all as specified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) |
25 | Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 125 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkatscomplete all as specified. |
26 | Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
27 | Factory made fully glazed, PVC window/ventilator shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;supply & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
28 | 35mm thick ,Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with bothfaces covered with decorative face veneer with lipping/frame to match complete all as specified and directed. |
29 | 35 mm thick2nd class hard wood (Sal/Hollock) glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members ofdoor shutters as specified in SSR- 2009Part-I Section 8.24(a) complete all as specified and directed. |
30 | Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x35mm double rebated comprisesgauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No"s for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07. Make : As per Appendix "C". Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day. |
31 | 2nd class hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary" labours; articles not exc 200 cu. cm each, complete all as specified. |
32 | Aluminium handles, cast type, anodised of size 150 mm complete all as specified and directed. |
33 | Aluminium handles, cast type, anodised of size 125 mm complete all as specified and directed. |
34 | Aluminium anodizedbarrel tower bolt of extruded section of size 200 mm and fixed complete all as specified and directed. |
35 | Aluminium anodizedbarrel tower bolt of extruded section of size 150 mm and fixed complete all as specified and directed. |
36 | Mild steel butt hinges of size 100mm medium weight cold rolledcomplete all as specified and directed. |
37 | Mild steel butt hinges of size 75mm medium weight cold rolledcomplete all as specified and directed. |
38 | 250mm longaluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed. |
39 | Steel locking bolts with mild steel electrogalvanised plate and bright bolt not less than 10mm dia 100mm size complete all as specified and directed. |
40 | Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm, complete all as specified and directed. |
41 | Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
42 | Sheet glass, 4 mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed. |
43 | 4mm thick, Figured glass, pinhead type in squares not exc 0.5 sqm in each pane,complete all as specified and directed. |
44 | Aluminium anodised snap grid frame work of size of size 605 mm X 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer"s catalogue/ instructions), cuttingholes for electrical fittings fixed on and including aluminium tee of size 25mmX25mmX1.50 mm as main runner, aluminium tee of size 25mmX25mmX1.25 mm as cross runner and aluminium angle of size 25mmX25mmX1.25mm at the perimeter suspended from soffit at approx 900 mm centre to centre with hangers 6 mm dia galvanised (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanised iron flat 40 mm X 3 mm size, 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm longincluding necessary scaffolding all as specified and directed. |
45 | 6mm thick, Non asbestos fibre cement building boards fixed or laid/ inserted to framework with screws, as in ceiling , including three coats of white wash complete all as specified. Note : The board shall be as per IS-14862 and shall be manufactured from homogeneous mixture of cement, quartz and cellulose and shall be cured with high pressure steam using auto claving process. |
46 | 18/19 mm thick, HDHMR (High Density high moisture resistance) board, exterior grade, with 1mm thick sun mica lamination on one side & other side balancing with white lamination, fixed with screws to timber frame work as in wall panelling/cup board shutters , fixed in repair complete all as specified and directed. |
47 | Continuous (piano) hinges,mild steel, bright finish or electrogalvanised, width of flap 40mm (when opened), complete all as specified. |
48 | Pre-painted galvalume aluminum zinc coating GI basedcorrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
49 | Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
50 | Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. |
51 | Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. |
52 | Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed. |
53 | Mild steel screw bolts (machine made). with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut., exc 22.5 cm but not exc 30 cm long., diameter of neck exc 16mm and not exc 20mm, complete all as specified. |
54 | Mild Steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165all as specified and directed. |
55 | Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
56 | Rolled mild steel work as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed. |
57 | Mild steel work as in hold fast,wind ties for roof includingsecuring bolts including all necessary drilling ,bolting or reverting etc and all similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed. |
58 | Plain fillets of 2nd class hard wood , square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc 13 & not exc 25sq.cm, complete all as specified & directed. |
59 | 15mm thick, 2nd class hardwood boarding, planed one side with butt joints , fixed with nail in any situationcomplete all as specified and directed. |
60 | Plain cement concrete 1:3:6, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75mmthick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved). |
61 | 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in sub base complete all as specified and directed. . |
62 | 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates)as in floor finish,surface finished even andfair to receive topfinish complete all as specified and directed. |
63 | Vitrified ceramic tiles (light shade) 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement mortar 1:6complete all as specified and directed. |
64 | Vitrified ceramic tiles (light shade) 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 Sqm, as in skirting/vertical surfaces etc , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
65 | Mat finish, premium quality, joint free (edge cut), coloured/ printed Non -Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed. |
66 | Glazed ceramic colouredtilesof size450mm x 300 mm x7mm / 350mm x 250 mm x7mm thick as in skirting/vertical surfaces etc , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the GE. |
67 | 20mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete. over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.complete all as specified and directed. |
68 | 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete, laid over and including 10mm thick rendering in cement mortar 1:4 complete, all as specified.. |
69 | Machine cut kota stone slab flooring 20-25 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 including cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified. |
70 | Machine cut kota stone slab flooring 20-25 mm thick as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab,as inin skirting, dados, risers to steps etc, laid over and including 10mm thick rendering in cement mortar 1:4 , cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified. |
71 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;, complete all as specified. |
72 | Chequered cement concrete colouredtiles, homogenious texture glossy finished, chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 15 mm thick cement screed in cement mortar 1:4 complete all as specified and directed. Shade/Colour of tile shall be approved by the GE. |
73 | Rendering cement plaster 15mm thick in cement mortar 1:4 on fair faces of brick wall or on concrete surfaces, mixed with water proofing compound surface finished even and smooth without using extra cement, all as specified. |
74 | Rendering cement plaster 15mm thick in cement mortar 1:6 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified. |
75 | Supply only liquid water proofing compound, complete all as specified. |
76 | Preparation of steel surfaces of any description, over 10cm in width or girth,not otherwise describedand applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and directed. |
77 | Preparation of wooden surfaces of any description, not otherwise described, over 10cm in width or girthand applying two coats of synthetic enamel paintover a coat of pinkprimer complete all as specified and directed. |
78 | Preparation of old steel surfaces of any description, over 10cm in width or girth,not otherwise describedand applying one coat of synthetic enamel paintcomplete all as specified and directed. |
79 | Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over and including2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed. |
80 | Preparation ofold surfaces of wall by Complete removal of existing treatment andapplying two coats of oil bound distemper over a coat of primer over and including2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed. |
81 | Preparation of old decorated plastered or unplastered surfaces including cleaning by brooming downor with steel wire brushing scraping down smoke soot, moulded moss and efflorescent salts and treating oil and greasy spotsand applying one coat of cement base paint on external surfaces on walls as specified and as directed. |
82 | Preparation ofnewplastered surfaces or un plastered, previously undecorated wall surfaces and applyingtwo coats of cement base paint over one coat of white wash, complete all as specified and directed. |
83 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old painted surfaces including preperation of old surfaces after complete removal of existing treatment, complete all as specified and directed. |
84 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as specified and directed. |
85 | G I tubingmedium gradeof 15 mm borewith all fittings and fixtures fixed to wall and ceiling or laid infloor/trenches including taking down old tubing complete all as specified and directed. |
86 | GI tubingmedium gradeof 20 mm borewith all fittings and fixtures fixed to wall and ceiling or laid infloor /trenches including taking down old tubing complete all as specified and directed. |
87 | Harrison rail (Curtain rail), mild steel, chromium plated with and including fixing brackets, stops, rollers etc. complete all as specified |
88 | Sink with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 910mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
89 | Angle Valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unionsfor 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified. |
90 | Stop valve, fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unionsfor 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified. |
91 | Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repair complete all as specified and directed. |
92 | Soap dish, SS, approximate size 160x 160x90mm, any type, fixed to plugs with chromium plated brass screws, fixed in repair complete all as specified. |
93 | Steel plate rack of overall size 900mm x 900mm x 250 mm made of stainless steel having thickness1mm, fixedoverfixing over 40cm long MS angle of size 25mmx25mmx3mm - 02Nos each , fixed in repair complete all as specified and directed. |
94 | S&F in repairs, Wall Mixer with Provision For Overhead Shower with 115mm Long Bend Pipe On Upper Side, Connecting Legs & Wall Flanges completeall as specified. Make : Jaquar Cat Part No. CON-273KNUPR or its equivalent approved make |
95 | Brass CP Sink mixer , swan neck for mixing hot & cold water screwed down for iron pipe and fixed,15mm size,completeall as specified. |
96 | Brass chromium plated tubular towel rail 20 mm dia, "D" type, 60 cms long between flanges fixed in repairs with and including chromium plated brass brackets, brass screws complete all as specified |
97 | PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, fixed in repair , all as specified.. |
98 | Vitreous China wash down water closet (pedestal pattern), white including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC white seat cover andchromium plated jet including PVC connection, fixedcomplete including demolition of old unservicable WC and provision of plain cement concrete M-15, type B-1 using 20mm graded crushed stone aggregate, fixed in repairs all as specified. Make: Cat Part No. 2008 for EWC, 2308 for seat cover, 2201/B for internal fittings of"Cera" or equivalent makes mentioned in PS. |
99 | Wash basins, Vitreous China , counter table top Size: 495x395x150 mm, coloured ,fixed in granite counter by making suitable holes, new brackets with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia , 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed,screwed for iron pipe and fixed, completefixed in repair all as specified. Make: Cat Part No. JDS-WHT-25909 of Jaquar or equivalent in makes mentioned in Appx |
100 | 600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers. |
101 | Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
102 | PVC (SWR) 110mm bore (dia) soil, waste and ventilating pipe, singe socketed, in any length with Rubber Ring Joints fixed to walls/floor, including taking down unserviceable pipe, fittings, etc, complete all as directed and all as specified. |
103 | PVC (SWR) 75mm bore (dia) soil, waste and ventilating pipe, singe socketed, in any length with Rubber Ring Joints fixed to walls, including taking down unserviceable pipe, fittings, etc, complete all as directed and all as specified. |
104 | PVC (SWR) 110mm bore (dia), Bends any type, with access door, with disminishing pieces or tapers and Jointing with Solvent Cement, complete all as specified and as directed. |
105 | PVC (SWR) 75mm bore (dia), Bends any type, with disminishing pieces or tapers and Jointing with Solvent Cement, complete all as specified and as directed. |
106 | PVC (SWR) 110mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed. |
107 | PVC (SWR) 75mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed. |
108 | 110 mm bore PVC (SWR) vent cowl, complete all as specified. |
109 | 110 mm bore PVC (SWR) "P’ trap, complete all as specified. |
110 | PVC connections 15 mm size with PTMT nutsof length 450mm fixed in repair complete all as specified and directed. |
111 | Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified. |
112 | Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 25mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified. |
113 | Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing ceiling/ exhaust fan and electric meters are to be refixed and connected properly where required. |
114 | Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surface complete all as specified and directed. |
115 | Point wiring with copper conductor cable multistrand, PVC sheathed 1.5 Sqmm size(two run with colour code RYB for phase and black for neutral) for one light point ,fan point, exhaust fan point,or bell point controlled by one switch including one run of 1.5 Sqmm (as continous earth wire Green)multistrand PVC concealed conduit of approved size and quality ISI marked,including all other required accessories as specified in preamable 1(a) to (q) of section 19 of SSR Part-II under heading "point wiring" fixedon wall/ceiling including concealedPVC/MS pressed steel cadmium plated modular terminal box not less than 1.6 mm thick for mounting switches, sockets, fan regulators etc and 3 mm thick modular laminated sheet top cover(ISI marked)cutting,chasing,pinning and making good the disturbed surface by using cement mortar 1:3 complete all as specified and directed by Engr-in-charge.,(Note:-the rate for concealed type point wiring shall deemed to include the cost of cutting,chasing in wall by using electric cutter andmaking good the disturbed surface of wall by providing cement plasterand matching the surface by white wash/colour wash all as per existing finishes complete). |
116 | All as per serial item No "115" above, but for one 3 pin 5 Ampssocket outlet on the same board all as specified and directed. |
117 | All as per serial item No "115" above, but for one 3 pin 5 Ampssocket outlet, independent all as specified and directed. |
118 | All as per serial item No. "115" above but for 3 pin 15 Amps socket out letindependentwith 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified. |
119 | Modular switch 1 way 6A, 1 module, complete all as specified. |
120 | Modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified. |
121 | Modular Bell push 6A 1 module, complete all as specified. |
122 | Modular switch 1 way 16A, 1 module,complete all as specified. |
123 | Socket 6A/16A - 2/3 pin combined , 2 module, all as specified and directed. |
124 | Modular fan regulator, step type, 2 module, all as specified. |
125 | Buzzer, Ding Dong AC. 230 volts, single pole, all as specified. |
126 | Modular White cover plate with frame, 1 module, complete all as specified. |
127 | Modular White cover plate with frame, 3 module, complete all as specified. |
128 | Modular White cover plate with frame, 8 module, complete all as specified. |
129 | Modular Metal flush box 1/2 module complete all as specified. |
130 | Modular Metal flush box 3 module complete all as specified. |
131 | Modular Metal flush box 8 module complete all as specified. |
132 | Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified. |
133 | Lamp holder, PVC/Polycarbonate type with back plate suitable for angular/ batten fittingscomplete all as specified & directed. |
134 | LED Bulb 9 watt, Cool/warm white 6500k, suitable for base B22/E27, 230 Volts, complete all as specified. |
135 | LED invertor Bulb 12 watt, Cool/warm white 6500k, suitable for base B22/E27, 230 Volts, complete all as specified. |
136 | Sub main wiring with two single core PVC insulated cable1100 volts grade with copper strandedRLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire ofsize 6 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor andone RM of earth wire of 6 Sqmm,shall be measured as one RM). |
137 | Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack., 10 watt LED,6500k, tube rod with all acessoreis internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable sizeincluding dismantling of unserviceable tube light all as specified and directed. Make: Havell"s Cat Part No. LHEXACP7IN1W010 of"Havells" or equivalent in makes mentioned in Appendix |
138 | Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack. 1x18W, 6500K ,230V, connector block etc completewith all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable sizeincluding dismantling of unserviceable tube light all as specified and directed. Make: Havells cat part No. LHEXACP7UN1W018 or equivalent in Appx |
139 | Endura Pearl 35Watt New generation energy saving and environmental friendly long life LED Bldg security light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate toughtned glass/verminproof driver compartment, SPDs with IP66 protection and impact resistance of IK07. connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of suitable size, complete all as specified Make: Havells cat part No. ENDURAPEARLPLUSSL135WLED757PASYTOPCLC or equivalent in Appx |
140 | MCB SPN 32-40 Amp, 240 Volts, 10 KA all as specified. |
141 | MCB SP 6 to 32 Amp, 240 Volts, 10 KA all as specified. |
142 | MCB TPN 63 Amps , 415 Volts, 10 KA all as specified. |
143 | Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 8 way, double door, 240 volts with 200 Amp rated bus bar completed all as specified. |
144 | Concealed sheet metal enclosurewith socket plug top and MCBs having single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20Amp 240V complete all as specified and as directed. |
145 | Sheet metal enclosures for DBs when MCBs to be used, triple pole and neutral, 4 way, double door, 415 volts with 200 Amp rated bus bar including taking down ICDP/ DB"s any type, kit kat fuse, MCB"s any type, all as specified. |
146 | Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified. |
147 | Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC (1:2:4), type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC (1:2:4), type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixingarrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electricalplate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. |
148 | Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 35 of tender doucments. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail