National Institute Of Technology-NIT has published Tender For Renovation Of Guest House Rooms (First Floor), Including Attached Bathrooms, At Nitc 2023-24. Submission Date for this Tender is 30-04-2024. Building Work Tenders in calicut Kerala. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | CEMENT CONCRETE (CAST IN SITU) |
| 2 | Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 3 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 4 | REINFORCED CEMENT CONCRETE |
| 5 | Reinforcedcement concreteworkinwalls(any thickness), includingattachedpilasters,buttresses,plinthandstring courses, fllets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: |
| 6 | 1:1.5:3 (1cement :1.5 coarsesand(zone-III)derivedfrom natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 8 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 10 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 11 | MASONRY WORK |
| 12 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. |
| 13 | Cement mortar 1:3 (1 cement :3 coarse sand) |
| 14 | CLADDING WORK |
| 15 | Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : |
| 16 | Decorative veneer facings of approved manufacture |
| 17 | WOOD AND P. V. C. WORK |
| 18 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 19 | Second class teak wood |
| 20 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hingesand necessary screwsshall be paid separately) |
| 21 | First class teak wood |
| 22 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 23 | Fixed to steel windows by welding |
| 24 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 25 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : |
| 26 | 125x64x1.90 mm |
| 27 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : |
| 28 | 200x10 mm |
| 29 | Providing and fixing bright finished brass door latch with necessary screws etc. complete : |
| 30 | 300x16x5 mm |
| 31 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 32 | Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. |
| 33 | Size 40 mm |
| 34 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 35 | Single rubber stopper |
| 36 | Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. |
| 37 | Double strip (horizontal type) |
| 38 | Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer- in-charge. |
| 39 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge |
| 40 | Extruded section profile size 42x50 mm |
| 41 | Providing and fixing to existing door frames. |
| 42 | 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places |
| 43 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. |
| 44 | 125 mm |
| 45 | Providing and fixing 20 mm thick marine plywood full gurjan or equvalent confirming to IS:710 for cupboards,shelves, partition, drawers, table top etc. including necessary screws etc. complete. |
| 46 | Providing and fixing 12 mm thick marine plywood full gurjan or equvalent confirming to IS:710 for cupboards,shelves, partition, drawers, table top etc. including necessary screws etc. complete. |
| 47 | Providing and fixing 47 mm thick factory made uPVC door shutters including uPVC door frame made of shutter styles and rails of a uPVC hollow section of size 47X125 mm and mullion with 47X109 wall thickness 2.5 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets wall thickness 2.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube. The lock rail made up of H section, a uPVC hollow section, fixed to the shutter styles by means of plastic/galvanised M.S. U cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 30 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, etc and door frame made of uPVC extruded frame sections profile size 60X90mm having an overall dimension as belo (tolerance ±0.2mm), with wall thickness 2.5 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube and stainless steel hinges fixed to the frame, including all fittings, door lock etc complete as per manufacturer specification and direction of Engineer in charge |
| 48 | Providing and fixing Head Board cushion for Cot using with 50mm thick upholstery foam and covered with high quality Rexine of approved make in all colors and shades in required grid type and fixed in 9mm plywood conforming IS:710 and fixing in existing cot etc complete as per direction of Engineer in Charge. |
| 49 | Providing and fixing metalic (SS 306,316 or equvalent) mosquito net of approved quality over aluminium frame work including cost and conveyance of all materialsand labour charges etc. complete but excludingcost of aluminium etc. complete |
| 50 | Providing and fixing high quality ISI marked stainless steel auto soft close hinges of specified size with stainless steel screws etc. complete. |
| 51 | FLOORING |
| 52 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. |
| 53 | Size of Tile 600x600 mm |
| 54 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). |
| 55 | Size of Tile 600x600 mm |
| 56 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 57 | Size of Tile 600x600 mm |
| 58 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. |
| 59 | Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 60 | ROOFING |
| 61 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 62 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 63 | 12.5 mm thick tapered edge gypsum moisture resistant board |
| 64 | FINISHING |
| 65 | 12 mm cement plaster of mix : |
| 66 | 1:4 (1 cement: 4 fine sand) |
| 67 | 15 mm cement plaster on the rough side of single or half brick wall of mix : |
| 68 | 1:4 (1 cement: 4 fine sand) |
| 69 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 70 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 71 | Applying priming coat: |
| 72 | With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 73 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer"s specifications including appropriate priming coat, preparation of surface, etc. complete. |
| 74 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 75 | Two or more coats on new work |
| 76 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 77 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. |
| 78 | Two coats |
| 79 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. |
| 80 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 81 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 82 | One or more coats on old work |
| 83 | French spirit polishing : |
| 84 | One or more coats on old work |
| 85 | Finishing walls with water proofing cement paint of required shade : |
| 86 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80/ 120 no. and then with sand paper of 160/180 nos.2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) |
| 87 | Providing and applying best quality wood putty (NC putty) of approved brand and manufacture,including cost for thinner,over wood surface to prepare the surface even and smooth complete. |
| 88 | REPAIRS TO BUILDING |
| 89 | Renewing glass panes, with wooden fillets wherever necessary: |
| 90 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) |
| 91 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 92 | Dismantling and Demolishing |
| 93 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 94 | Of area 3 sq. metres and below |
| 95 | Of area beyond 3 sq. metres |
| 96 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : |
| 97 | Of area 3 sq. metres and below |
| 98 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 99 | For thickness of tiles 10 mm to 25 mm |
| 100 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 101 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 102 | Taking out door frames and shutters (PVC or Plywood) including stacking within 50 metres lead : |
| 103 | Of area 3 sq. metres and below |
| 104 | Dismantling water closet (Indian or European) of all types (C.I./PVC/Vitrious China) with foot rest, trap, etc including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 105 | Dismantling cement asbestos/thermocol or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials to engineering unit store as per instruction from engineer in-charge. |
| 106 | SANITARY INSTALLATIONS |
| 107 | Providing and fixing white vitreous china pedestal type water closet(European type) with seat and lid, 10 litre low level white vitreouschina flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standardmake and mosquito proof coupling of approved municipal designcomplete, including painting of fittings and brackets, cutting andmaking good the walls and floors wherever required : |
| 108 | W.C. pan with ISI marked white solid plastic seat and lid |
| 109 | Providing and fixing white vitreous china flat back or wall corner typelipped front urinal basin of 430x260x350 mm and 340x410x265 mmsizes respectively with automatic flushing cistern with standard flushpipe and C.P. brass spreaders with brass unions and G.I clampscomplete, including painting of fittings and brackets, cutting andmaking good the walls and floors wherever required : |
| 110 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever require: |
| 111 | Providing and fixing white vitreous china flat back or wall corner typelipped front urinal basin of 430x260x350 mm or 340x410x265 mmsizes respectively. |
| 112 | Providing and fixing 600x450 mm beveled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washerscomplete. |
| 113 | Providing and fixing toilet paper holder: |
| 114 | C.P. brass |
| 115 | Providing and fixing Stainless Steel towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 116 | 600 mm long towel rail with total length of 645 mm, width78 mm and effective height of 88 mm |
| 117 | Providing and fixing White Vitreous Chinatable top wash basin size 550x400 with 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingcutting and making good the table wherever require. |
| 118 | WATER SUPPLY |
| 119 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work |
| 120 | 20 mm nominal dia Pipes |
| 121 | 25 mm nominal dia Pipes |
| 122 | 32 mm nominal dia Pipes |
| 123 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 124 | 150 mm diameter |
| 125 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 126 | 15 mm nominal bore |
| 127 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 128 | 15mm nominal bore |
| 129 | Providing and fixing Stainless Steel grating of approved quality and colour. |
| 130 | Rectangular type with openable rectangular lid |
| 131 | 100 mm nominal size square |
| 132 | Providing and fixing Polyvinyl Chloride (PVC) pipes, including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 133 | 50 mm nominal dia Pipes (10kg/cm2) |
| 134 | 63 mm nominal dia pipe (6kg/cm2) |
| 135 | 110 mm nominal dia Pipes (4kg/cm2) |
| 136 | 90 mm nominal dia Pipes (4kg/cm2) |
| 137 | Providing and fixing C.P. brass Health Fauset of approved quality conforming to IS:8931 : |
| 138 | C P Brass Health Fauset |
| 139 | Providing and fixing 15 mm nominal bore C.P. brass push cock of approved quality conforming to IS:8931. |
| 140 | Providing and fixing Stainless steel shower rose (200X200mm) for cold/ hot water with 15 or 20 mm inlet arm : |
| 141 | Supplying and fixing stainless steel Jaqur Queen Wall Mixer (inside valve set and outer handle kit) including shower control and Jaqur Queen telephonic bib cock (control by wall mixer)of approved quality including all cost conveyance labour charges etc complete as per the instructions of the engineer |
| 142 | Providing and fixing Polyvinyl Chloride (PVC) pipes 75mm nominal dia (6Kg/cm2), including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 143 | Providing and fixing SS soap Dish Holder having length not less than 120mm, with concealed fitting arrangements, |
| 144 | ALUMINIUM WORK |
| 145 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : |
| 146 | For fixed portion |
| 147 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 148 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 149 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 150 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 151 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 152 | Providing and fixin Aluminium composite panel (ACP) two side same finish board in panneling fixed in aluminium doors, windows shutters and partition frames with stainless steel screws etc. |
| 153 | 4 mm thick Aluminium Composite Panel (ACP) |
| 154 | WATER PROOFING |
| 155 | Providing and laying water proofing treatment over the concrete surface by applying cement based two component polymer modified water proofing slurry coating coating (SIKA 109 TOP seal or equivalent)after cleaning the surface free from scale, rust, grease, oil etc. preparing the surface to be true and flat and saturatedmixing the liquid (A) and powder (B) components in the ratio 1:4 by weight, applying in two coats with an interval of 2 to 6 hours for hardening in between and finally finished by rubbing down with a soft, dry sponge including protecting the applied surface from direct sunlight and storng wind and curing by gunny bags or polythene sheeting upto 5 days etc. complete. |
| 156 | NON SCHEDULE |
| 157 | providing and fixing ball valve (UPVC) approved quality,high or low pressure,with PVC floats complete. |
| 158 | 25 mm nominal bore |
| 159 | Providing and fixing room sign board in 2mm thick stainless steel plate size of 200x100mm, including lettering by engraving and carving (up to 3 Nos), as per direction in Engineer in charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
