Military Engineer Services-MES has published Tender For Additional/Alternator To Bldg No P-187 At Af Station Barrackpore Under Ge (Af) Barrackpore. Submission Date for this Tender is 20-04-2024. Building Work Tenders in barrackpore West Bengal. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 09-Apr-2024 | Revised BOQ | BOQ | 20-04-2024 |
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un-reinforced) of any description and in any position including removing debris from site of work complete all as specified and directed. |
| 2 | Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and directed. |
| 3 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 4 | Dismantling of structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed. |
| 5 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 6 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards / slabs / blankets any thickness, including cover fillet / snap grid complete all as specified and directed. |
| 7 | Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for key, scrubbingdown with water etc. and removing debrish from site complete all as specified and directed. |
| 8 | Dismanting of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 9 | Taking down chowkats or frames with shutters n.exc. 1.50 sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 10 | Taking down chowkats or frames with shutters exc. 1.50 Sqm but n.exc. 4.00 Sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 11 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth, for foundation, etc. or for laying of cable or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting outcomplete all as specified and directed. |
| 12 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 250mm in soft/loose soil, complete all as specified and directed. |
| 13 | Removing excavatedmaterial notexc 50 m and depositing where directed at a level not exc 1.5 m above the starting point as in soft/loose soilcomplete all as specified and directed. |
| 14 | Removing excavatedmaterial exc 250m but notexc 500 m and depositing where directed at a level not exc 1.5 m above the starting point as in soft/loose soilcomplete all as specified and directed. |
| 15 | Material and labour for PCC (1:4:8) type D2 (using 40 mm graded stone aggregate ) as in foundation, filling and mass concrete complete all as specified and directed. |
| 16 | Material and labour for PCC (1:3:6) type C2 (using 40 mm graded stone aggregate ) as in foundation, filling and mass concrete complete all as specified and directed. |
| 17 | Materials and labour for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 18 | Materials and labour for providing precast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling) corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match and set incement mortar (1:4) complete all as specified and directed. |
| 19 | Material and labour for RCC (1:2:4) (nominal mix) type B-1 (using 20mmgraded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 20 | Material and labour for pre-cast RCC (1:2:4) type B1 (using 20 mm graded stone aggregate)in landings, cover slabs, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set incement mortar (1:4) complete all as specified and directed. |
| 21 | Supply only liquid water proofing compound (WPC) completeall as specified and directed. |
| 22 | Material and labour for brick work with fly ash modular size bricksstraight or curved on plan exc.6 m mean radius built in cement mortar (1:6) complete all as specified and directed. |
| 23 | Materials and labour for half brick thick brick work with fly ash bricks straight or curved on plan to any radius built in cement mortar(1:4) complete all as specified andas directed. |
| 24 | Material and labour for cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. including removing rubbish from site complete all as specified and directed. |
| 25 | Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or slopping) with rough finished flat surfaces of concrete complete all as specified and directed. |
| 26 | Material and labour for forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work complete all as specified and directed. |
| 27 | Material and labour for making good under cills or over arches, lintels and bressummers including allpinning when necessary complete all as specified and directed. |
| 28 | Material and labour for well-seasoned 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. |
| 29 | Supply and fix factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 30 | Supply and fix factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: stainless steel butt hinges shall be paid separately under respective items. |
| 31 | Supply and fix 125mm size hasp and staple safety type ,aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 32 | Supply and fix continuous (piano) hinges mild steel bright finish or electro galvanised of 40mm width of flaps (when open) complete all as specified and directed. |
| 33 | Supply and fix MS Butt hinges medium weight cold rolled 100mm sizecomplete all as specified and directed. |
| 34 | Supply and fix aluminium handle fabricatedtype, anodised 125mm size complete all as specified and directed. |
| 35 | Supply and fix Mortice lock, vertical type, brass body size 100mm omplete all as specified and directed. |
| 36 | Supply and fix 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 37 | Supply and fix 200mm long aluminiumanodized barrel tower bolts of extruded section complete all as specified and as directed. |
| 38 | Supply and fix 200mm size aluminium alloy handles, fabricated type extruded section complete all as specified and directed. |
| 39 | Supply and fix 140mm long floor door stopper of aluminium alloy body tongue, anodised, with hard drawn steel spring fixed to door complete all as specified and directed. |
| 40 | Supply and fix20mm dia harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc.complete all as specified and directed. |
| 41 | Supply and fix door closer hydraulically regulated aluminium (extruded section body), designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 42 | Supply and fix stainless steel wire cloth, 0.36mm nominal dia or wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 43 | Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed. |
| 44 | All as per item No 43.00 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and .-ditto-. |
| 45 | Supply and fix mild steel works as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 46 | Supply and fix mild works as in steel chimney bars (straight or camber), bearing bars; tongues or water bars for window frames, window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 47 | Supply and fix anodised powder coated (minimum thickness of powder coating 50 micron) aluminium frames for door, window , ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and directed. |
| 48 | Supply and fix anodised powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed. |
| 49 | Supply and fix anodised powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. |
| 50 | Supply and fix anodised powder coated (minimum thickness of powder coating 50 micron) aluminium ventilator shutters, side hunge type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed. |
| 51 | Supply and fix anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed. |
| 52 | Supply and fix of suspended ceiling system with 9mm thick gypsum board edge tiles of size 593mm X 593mm with GI prelude section of 24mm face exposed grid of 600mm X 600mm (nominal). The tile shall have smooth vinyl laminated visual with washable metalised polyster foil backing & vinyl covered edges. The tile shall be laid on prelude 32 with 24mm wide T-section flanges colour global white (matching to tile colour) having roll formed double stroke rotary stitching on all T-sections i.e. the main runner 1200mm & 600mm cross Tees with a web height of 38mm (all sections). The perimeter trim to be wall angles of size 19mm X 19mm, secured to walls using screws at 450mm c/c maximum. The Tees, wall angle and the suspension system material shall be hot dipped galvanised steel of 90 gsm as per IS-277 (2003) and prepainted steel with baked polyster paint with OT bending capability. The grid shall be suspended with the accessories consisting of M6 anchor fasteners with hanger hole, pre straightened hanger wire of 2.5mm of required length (max 1.8m) having tensile strength of 344-413 Mpa (optionally, adjustable hook clips made of 0.7mm thick Grade 1- C55 galvanised spring steel of dimension 100mm X 20mm and 4mm aquiline wire to be used for level adjustment of main runners). The installation shall be carried out as per manufacturer"s recommended procedure complete all as specified and directed. Make: Armstrong/ Saint GobAin/ Lafarge. |
| 53 | Supply and fix 18mm thick pre-laminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination with 2nd class hard wood 6mm thick leaping, fixed with screws to timber frame work complete all as specified and as directed. |
| 54 | Supply and fix 12mm thick pre-laminated particle board, exterior grade, prelaminated on both side with decorative choice lamination fixed with screws to timber frame work complete all as specified and as directed. |
| 55 | Supply and fix 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based corrugated / semi corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and directed. |
| 56 | Material and labour for 75mm thick PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection including finishing theconcrete surface even and smooth without using extra cement complete all as specified and directed. |
| 57 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred /stopped endsetc complete all as specified and directed. Note:- Only inner girth shall be measuredforpayment. |
| 58 | Material and labour for 100mm thick PCC (1:4:8), type D-2, (using 40mm graded stone aggregate) as in sub base of floor and pavings etc complete all as specified and directed. |
| 59 | Material and labour 25mm thick PCC (1:2:4), type B-0 (using 12.5 mm graded stone aggregate) as in levelling course for laying floor finishes etc. complete all as specified and directed. |
| 60 | Material and labour for non skid ceramic coloured tiles (premium quality) 7 to 8mm thick (square or rectangular) area of each tile exc. 0.18 Sqm but not exceeding 0.38 Sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed. |
| 61 | Material and labour for glazed ceramic tiles of size 350x250x7 mm / 450x350x7mm (premium quality) coloured in vertical surfaces such as riser of steps, skirting, dado and pillar set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick cement plaster in cement mortar (1:4) completeall as specified and directed. |
| 62 | Material and labour for double charged virified ceramic tiles (light shade) (premium quality) 7-8 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match,laid over and including 15mm thick screed bed in cement mortar (1:6)complete all as specified and directed. |
| 63 | Material and labour for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding andpolishing complete laid over and including 20mm thick cement screed bed or bedding layer in CM (1:6) complete all as specified and directed. |
| 64 | Providing and laying factory made, rubber moulded, machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 65 | Complete removal of existing roof treatment in any layers and disposal of debris from sitecomplete all as specified and directed. Notes: - (a) The rates are inclusive of removal for any type of old water proofing treatement over main RCC slab. (b) Bidders are advised to visit the site and esure about site condition before quoting their rates. (c) Demolition of PCC shall be measured and paid saparately under respective items. |
| 66 | Material and labour for PCC (1:2:4) type B0 (using 12.50 mm graded stone aggregate) mixed with water proofing compound @ 200 ml per bag of cement or as per manufacturer instruction as in levelling course to match undulation of roof, in coving, roof kerbs including benching or mud stops, rounded or chamfered on edges etc including necessary form work and finished the rough surface complete all as specified and directed. Note : WPC will be measured and paid separately under respective item. |
| 67 | Material and labourfor 5mm thick rendering in cement mortar (1:3) with using water proofing coumpound (WPC) @ 200 ml per bag of cement or as per manufacturers instruction on roof top while concrete is green to become integrated part of concrete padding layer and finish the surfaceseven and smooth without using extra cement complete all as specified and directed. Note : WPC will be measured and paid separately under respective item. |
| 68 | Material and labour for water proofing treatment to RCC roof surface comprising with the following course of treatment/specifications from bottom to top :- (a) Applying cold bituminous primer @ 0.30 liters per sqm confirming to IS 3384 over plastered surfaces of roof. (b) One layer of APP based polymeric membrane3mm thick, weight not less than 3.50 kgs per sqm, reinforced with non woven polyester matt central core fabric (weight not less than 160 GSM) and coated on both side with and including layer of APP modified bitumen and finished with and including micro-prefabricated heat fusible polythene film on both surfaces. (c) Finally applying two coats of aluminum paint @ 0.10 ltrs per sqm per coat on top surface. Contd... |
| 69 | Note:- (i) The work shall be executed only through authorised applicator of manufacturer as approved by GE. (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions. (ii) A minimum overlap of 150mm and 100mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instructions. Make of APP membrane:- Super Thermolay of M/s STP Ltd, Hyperplas of M/s IWL India Ltd, Hydrostop of M/s Tiki Tar Danosa (India) pvt ltd, , M/s FOSROC Chemicals, Smartcare APP membranes of M/s Asian Paints Ltd. |
| 70 | Material and labour for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:6) andfinish the surfaceseven and smooth without using extra cement as in wall complete all as specified and directed. |
| 71 | Material and labour for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:4) andfinish the surfaceseven and smooth without using extra cement as in wall complete all as specified and directed. |
| 72 | Material and labour for 5mm thick rendering on concrete surfaces in cement mortar (1:3) andfinish the surfaceseven and smooth without using extra cement as in ceiling complete all as specified anddirected. |
| 73 | Materials and labour for complete removal of existing treatment on walls and applying 2mm thick wall care putty and after two coats of 100% premium acrylic emulsion paint (camouflage pattern) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming one coat of exterior primer applied @ 0.90 litre/ 10 sqm including preperation of surfaces complete all as specified and directed. |
| 74 | Materials and labour for complete removal of existing treatment on walls and applying 2mm thick wall care putty and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer"s specification including preperation of surfaces complete all as specified and directed. |
| 75 | Materials and labour for preparation of new plastered surface of wall applying 2mm thick wall care putty and and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer"s specificationcomplete all as specified and directed. |
| 76 | Materials and labour for complete removal of existing treatment on ceilings and applying 1mm thick wall care putty and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer"s specification including preperation of surfaces complete all as specified and directed. |
| 77 | Materials and labour for preparation of new plastered surface of wall applying 2mm thick wall care putty and after two coats of 100% premium acrylic emulsion paint (camouflage pattern) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming one coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 78 | Material and labour for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and directed. |
| 79 | Material and labour for preparation of new steel surfaces of any description over 10 cm width or girthand applying two coats ofsynthetic enamel paint over a coat of red oxide zinch chrome primer complete all as specified and directed. |
| 80 | Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girthand applying one coat ofsynthetic enamel paint complete all as specified and directed. |
| 81 | Material and labour for preparation of old painted wooden surfaces over 10 cm girth and applyingone coat of synthetic enamel paint complete all as specified and directed. |
| 82 | Material and labour for preparation of new wooden surfaces of any description exc 10 cm width or girthand applying two coats ofsynthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 83 | Material and labour for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with one coat of creosote oil complete all as specified and directed. |
| 84 | Material and labour for sanding newly tarred or painted surfaces with clean sharp sand complete all as specified and directed. |
| 85 | Supply and fix 3mm thick sheet glass,ordinary quality with Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed. |
| 86 | Material and labour for cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in bed to 150 mm bore drain pipes including packing under and haunching against the sides of pipeafter they are laid and tested complete all as specified and directed. |
| 87 | Materials and labour for 150mm bore reinforced concrete pipes, class NP3, laid and jointed complete with collarscomplete all as specified and directed. |
| 88 | Materials and labour for cutting into existing manholes for connecting new drains of 150mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed. |
| 89 | Supplying and laying 20mm (outer dia ) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 90 | Supplying and laying 25mm (outer dia ) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 91 | Supplying and laying 32mm (outer dia ) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 92 | Supply and fix 25mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed. |
| 93 | Supply and fix brass chromium plated shower rose 125mm size complete all as specified and directed. |
| 94 | Supply and fix toilet paper holder with flat recessed type stainless steel complete all as specified and directed |
| 95 | Supply and fix soap dish, brass chromium plated of approximate size 100x80 mm complete all as specified and directed. |
| 96 | Supply and fix towel Rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190gms) complete all as specified and directed. |
| 97 | Supply and fix in repair 20mm bore gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. |
| 98 | Supply and fix in repair 25mm bore gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. |
| 99 | Supply and fix in repair 15mm bore fancy type, chromium plated, bib tap, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed. |
| 100 | Supply and fix in repair 15mm bore fancy type pillar tap cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed. |
| 101 | Supply and fix in repair 15 mm dia stop valves, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe orunions complete all as specified and directed. |
| 102 | Supply and fix swivel shower of PTMT any colour for fixing with 15mm pipe (minimum weight 40gms) with shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour (minimum weight 40gms)complete all as specified and directed. |
| 103 | Supply and fix PVC connection pipe 15 mm size with PTMT nuts at both ends of length 600 mm complete all as specified and directed. |
| 104 | Supply and fix in repair Vitreous china wash basin white flat back size 630 x 450mmincl cutting for and pinning in ends of brackets or erectting stand incl 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basin with long screws shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 105 | Supply and fix in repair vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern including all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified and directed. |
| 106 | Supply and fix in repair plastic water closet seat white closed pattern with flat bottom and cover mild steel chromium plated or aluminium hinging device complete all as specified and directed. |
| 107 | Supply and fix in repair 10 ltr capacity PVC valveless, syphonic action type, dual flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and 32mm dia PVC flush pipe complete all as specified and directed. |
| 108 | Supply and fix in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 109 | Supply and fix600mm x 450mm beveled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 110 | Supply and fix 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or fixed to walls complete all as specified and directed . |
| 111 | Supply and fix 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or fixed to walls complete all as specified and directed . |
| 112 | Supply and fix 110mm bore PVC (SWR) bends of any radiuswith access door complete all as specified and directed . |
| 113 | Supply and fix 110mm bore PVC (SWR) bends of any radius complete all as specified and directed . |
| 114 | Supply and fix 75mm bore PVC (SWR) bends of any radius complete all as specified and directed . |
| 115 | Supply and fix 75mm bore, PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 116 | Supply and fix 75 mm dia PVC (SWR) multi floor trap with grating including jointing with solvent cementcomplete all as specified and directed. |
| 117 | Supply and fix PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. |
| 118 | Supply, hoist and fix 500 litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of old unseviciable existing tank complete all as specified and directed. |
| 119 | Supply and fix sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 120 | Material and labour for light/fan point wiring (concealed type) with single core PVCinsulated unsheathedmultistranded FRLSH copper conductor cable of 1100 volts grade size 1.5 sqmm (nominal area) in and including 20mm dia heavy duty rigid non metalic PVC conduit with accessories including modular flush metal boxeswith inner and outer modular cover plates for housingswitches, sockets and regulatorswith all fittings and fixing materials with one single core PVC insulated unsheathed 1.5 sqmm (nominal area) multistranded FRLSH copper conductor as earth continuity wire and connected to earth dully including taking down old unserviceable existing point wiring with all fixtures such as switches, sockets etc.complete all as specified and directed. Note: (a) Red coloured cable shall be used for live connection,black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for Each individual circuit from the distribution board. (b) Quoted rate shall be included for cuttings /chasing the wall and making good disturbed surfaces to fix PVC conduit and MS terminal box. |
| 121 | All as per item No. 119.00 here-in-before but for one five pins 5 Amps switch socket outlet point on independent board and -ditto-. |
| 122 | All as per item No. 119.00 here-in-before but for one five pins 5 Ampsswitch socket outlet point on same board and -ditto-. |
| 123 | All as per item No. 119.00 here-in-before but for 15 amps socket outlet with 2.50 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade including 2.50 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade as earth continuity conductor and connecting to common earth dully and -ditto-. |
| 124 | All as per item No. 119.00 here-in-before but for metal clad industrial socket with 4.00 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade including 4.00 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade as earth continuity conductor and connecting to common earth dollyand -ditto-. |
| 125 | Supply and fix modular switch 1 way 6 amps, 1 module complete all as specified and directed |
| 126 | Supply and fix modular switch 1 way 16 amps, 1 module complete all as specified and directed. |
| 127 | Supply and fix modular shuttered sockets 6 amps, 3/5 pin combined two module complete all as specified and directed. |
| 128 | Supply and fix modular shuttered sockets 6/16 amps, 3/5 pin combined two module complete all as specified and directed. |
| 129 | Supply and fix modular fan regulator step type 120W, 2 module complete all as specified and directed. |
| 130 | Supply and fix modular type telephone socket 1 module complete all as specified and directed. |
| 131 | Supply and fix ceiling rose, 3 terminals, fabricated of PVC/Polycarbonate, isolated body complete all as specified and directed. |
| 132 | Supply and fix in repair industrial plug and socket type DB (functional unit) 20 Amps capacity with provision of single pole 20 amps MCB, plug top and earth plug, grouted flush to walls complete all as specified and directed. |
| 133 | Supply and fix in repair sheet metal enclosure VTPN DB 4 ways double door having facility to fix MCCB in incomer and MCBs in outgoing, IP-43 with metal door type complete fitted with bus bars, neutral links, blanking plates etc.complete all as specified and directed. |
| 134 | Supply and fix in repair sheet metal enclouser SPN DB 8 ways double door having facility to fix MCB in incomer and MCBs in outgoing, IP-43 type complete fitted with 200 Amp rated bus bars, neutral links, blanking plates complete all as specified and directed. |
| 135 | Supply and fix in repair sheet metal enclouser SPN DB 4 ways double door having facility to fix MCB in incomer and MCBs in outgoing, IP-43 type complete fitted with 200 Amp rated bus bars, neutral links, blanking plates complete all as specified and directed. |
| 136 | Supply and fix in repair MCB SPN, 240 Volts, of 40 amps current rating, 10 KA breaking capacity "C" series complete all as specified and directed. |
| 137 | Supply and fix in repair MCB SP, 240 Volts, of 10 to 32 amps current rating, 10 KA breaking capacity "C" series complete all as specified and directed. |
| 138 | Supply and fix in repair MCCB 100 Amps current capacity, 415V, 16 KA, 4 Pole, with adjustable thermal andmagnetic type complete all as specified and directed. |
| 139 | Supply and fix in repair LED lights fittings with extruded aluminium housing, high quality PC diffuser, efficacy- 125lm/W, 20 watt, 4 feet long, 220V, AC, 3000K, CRI =80, integrated design including connecting up with 3 core flexible copper conductor cable of suitable size complete all as specified and directed. Make:- Crompton /Wipro / Philips/ GE. |
| 140 | Supply and fix in repair 36 W recessed LED ceiling light with glare free uniform illumination, white powder coated CRCA housing, efficacy > 100 lm/W suitable for 600 x 600 mm (2 feet x 2 feet)grid ceiling complete with all accessories including internally prewired connecting upto 3 core twisted flexible copper conductor cable of suitable size complete all as specified and directed. Make:- Crompton /Wipro / Philips/ GE. |
| 141 | Supply and fix in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast housing toughened glass, 5700K, IP 66 protection inbuilt surge protection, efficacy = 110LPW, high powered LED complete all as specified and directed. Make:- Crompton /Wipro / Philips/ GE. |
| 142 | Supply and fix ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete complete all as specified and directed. |
| 143 | Material and labour for street light bracket made of 1.5 RM length of GI pipe of medium grade of 40 mm dia in proper shape, bend, threadedand drilling holes for wire entry and MS clamps (02 Nos) of suitable size in proper shape cmplete all as specified and directed. |
| 144 | Material and labour for concealed sub-main wiring comprising single core , 2 runs of 4 sqmm nominal cross sectional area, FRLSHmultistrandedcopper conductor cable, PVC insulated unsheathed 1100 volts gradedrawing in and including 25mm dia heavy duty PVC conduit and its fittings complete including provision of 1x4 sqmm nominal cross sectional area single core FRLSH multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earthwire including taking down old unserviceable sub-main wiring complete all as specified and directed. Note :-(i) Extra length of cables/ wire required for connection to MCBs/DB"s shall be included in quoted rate. (ii) Quoted rate shall be included for cuttings /chasing the wall and making good disturbed surfaces. |
| 145 | Material and labour for concealed sub-main wiring comprising single core , 2 runs of 6 sqmm nominal cross sectional area, FRLSHmultistrandedcopper conductor cable, PVC insulated unsheathed 1100 volts gradedrawing in and including 25mm dia heavy duty PVC conduit and its fittings complete including provision of 1x6 sqmm nominal cross sectional area single core FRLSH multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earthwire including taking down old unserviceable sub-main wiring complete all as specified and directed. Note :-(i) Extra length of cables/ wire required for connection to MCBs/DB"s shall be included in quoted rate. (ii) Quoted rate shall be included for cuttings /chasing the wall and making good disturbed surfaces. |
| 146 | Material and labour for earthing complete with copper earthplate electrode of size 600 x 600 x 3.15mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to copper strip of size 20 x 3mm earth lead by means brazing after fixing of nuts, bolts, check nuts, washers of galvanised iron steel,protected by 40 mm bore HDPE pipe of pressure rating 6 kgf/sqcm allas directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x 6cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 15 cm long, bent to shape as lifting handle, funnel,wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, earth testing point, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion including taking down old existing unserviciable earthing complete all as specified and directed. Note:- Strip upto 7.5m length including testing shall be included in quoted rates. |
| 147 | Material and labour for copper strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground including taking down old unserviceable copper earthing strip complete all as specified and directed. |
| 148 | Material and labour for copper strip 20 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground including taking down old unserviceable copper earthing strip complete all as specified and directed. |
| 149 | Material and labour for aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground after taking down old unserviceable strip complete all as specified and directed. Note : Joining of aluminium strip shall be made by brazing/soldering. |
| 150 | Materials and labour for 50mm dia high density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 with all fittings fixed complete to walls, ceilings or in floors etc including taking down old unserviciable existing pipe complete all as specified and directed. |
| 151 | Material and labour for test point termination box made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including 3 Nos, 8 mm dia, 25mm long hexagonal heads screw for lighting conductors including taking down old existing unserviciable termination box complete all as specified and directed. |
| 152 | Material and labour for air termination single pointed copper rod,12mm dia and 300mm long including necessary fixing arrangment using clamps,nuts and nuts including taking down old unserviceable air termination rod complete all as specified and directed. |
| 153 | Supply and fix in repair porcelain insulator for supporting or passing of earthing strip from roof / wall including necessary nuts and bolts complete all as specified and directed. |
| 154 | Materials and labour for cutting, welding, bending of MS flat iron of size 30x3mm for making clamps of requiredshap and size as per site condition including nut & bolts and applying two coats of synthetic enamel paint over a coat of zinc chrome primer including dismantling of existing unserviceable clamps complete all as specified anddirected. |
| 155 | Material and labour for painting of earth pit chamber of size 42 x 42 cm by two coats of synthetic enamel paint after cleaning earth pit properly with iron wire brush and indicating board as per colour code complete all as specified and directed. |
| 156 | Material and labour for welding/soldering/brazing tothe earthing strip joints in replacement of existing nuts bolts joints complete all as specified and directed. |
| 157 | Supply and fix thermoplastic enclosure box of size 300x150x170mm with opaque lid fasteners for tool operation protection of IP-66 for fixing of test point terminal box complete all as specified and directed. Make:- HENSEL / SINTEX / C&S |
| 158 | Supply, laying, connecting and testing XLPE insulated, PVC sheathed, armoured LT electric power UG cable (heavy duty with stranded aluminum conductor)of size 50 Sqmm, 3.5 core, 1100 Volts (earthed) grade, confirming to IS-7098 (Part-I) laid through duct/ pipe / in trench etc. with cable glands & suitable size of aluminium lugs complete all as specified and as directed. Note : Earth work, brick protection and sand cushioning and GI Pipe Shall be measured and paid separately under respective item. |
| 159 | Materials and labour for boring of holes of size up to 50mm dia under road without disturbing the top surface of the road and taxiway for passing through the cable complete all as specified and directed Note-Necessary infrastructure required for boring shall by arranged by the contractor and cost of the same included in quoted rates. |
| 160 | Material and labour for sand cushioning with clean and dry river sand for protection of UG cable with approved sand of uniform thickness. laid dry, filling in trenches and punning down in proper required layers complete all as specified and directed. Note:- Punned down thickness shall be measured for payment. |
| 161 | Material and labour for brick protection cover to underground cables with sub class ‘B’ bricks of size 23 X 11.5 X 7.5 cm, (locally available best quality), laid dry and flat complete all as specified and directed. |
| 162 | Materials and labour for 50mm dia high density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2with all fittings for protection of cables to cross under road, hard standing, pavement etc complete all as specified and as directed. |
| 163 | Supply, installation, testing and commissioning of energy rating 5 star, inverter split Air Conditioner capacity 2 Ton with indoor and outdoor unit comprising of the following:- (a) Multi-stranded copper conductor wire 3 core, 2.50 Sqmm not less than 3.0 mtrs with copper lugs. (b) Incoming and outgoing high quality copper pipe with foam insulation duly white taped of each size not less than 3.0 mtrs. (c) Key features: - (i) Multi adjustable mode. (ii) High ambient cooling. (iii) Super dry. (iv) Turbo cooling. (v) Anti microbial air filteration. (vi) Eco-friendly refrigerant R-32/ R-410A. (vii) 100% copper. (viii) Sleep mode. (ix) Wide voltage range operation. (x) The ISEER vlaue of Air Conditioner shall be 4.5 (minimum). (xi) Cordless remote - 01 No. |
| 164 | Notes: - (i). Extra copper pipe and multistranded copper conductor wire required for Air Conditioner to be installed on parapet wall of building roof top shall deemed to be included in quoted rate. (ii). Rate for scaffolding/ladder/tools and plants required to install Air Conditioner i.e. for making holes to wall, drilling, making good disturbed surfaces and matching with the existing colour shall deemed to be included in quoted rate.(iii) Outdoor unit should be kept above the level of Indoor unit. For installaiton of ground floor ACs oudoor should be on wall surfaces and for first floor ACs should be on parapet wall of roof top of the building with out extra cost to the Govt all as directed by Engr-in-chrg. (iv) The MES No should be painted on indoor and outdoor unit with navy blue colour letters of size not less than 15 mm height. Drain pipe should be clamped up to plinth protection. No extra claim should be allowed for drain pipe from indoor unit to plinth protection of outside the building. (v) The quoted rates are also inclusive of making holes in brick/stone wall for installation of Air Conditioner and making good tothe exisitng surface with putty and paint in as specified and directed by Engr-in-charge. |
| 165 | Supply, installation, testing and commissioning of energy rating 5 star, inverter split Air Conditioner capacity 1.5 Ton with indoor and outdoor unit comprising of the following:- (a) Multi-stranded copper conductor wire 3 core, 2.50 Sqmm not less than 3.0 mtrs with copper lugs. (b) Incoming and outgoing high quality copper pipe with foam insulation duly white taped of each size not less than 3.0 mtrs. (c) Key features: - (i) Multi adjustable mode. (ii) High ambient cooling. (iii) Super dry. (iv) Turbo cooling. (v) Anti microbial air filteration. (vi) Eco-friendly refrigerant R-32/ R-410A. (vii) 100% copper. (viii) Sleep mode. (ix) Wide voltage range operation. (x) The ISEER vlaue of Air Conditioner shall be 4.5 (minimum). (xi) Cordless remote - 01 No. |
| 166 | Notes: - (i). Extra copper pipe and multistranded copper conductor wire required for Air Conditioner to be installed on parapet wall of building roof top shall deemed to be included in quoted rate. (ii). Rate for scaffolding/ladder/tools and plants required to install Air Conditioner i.e. for making holes to wall, drilling, making good disturbed surfaces and matching with the existing colour shall deemed to be included in quoted rate.(iii) Outdoor unit should be kept above the level of Indoor unit. For installaiton of ground floor ACs oudoor should be on wall surfaces and for first floor ACs should be on parapet wall of roof top of the building with out extra cost to the Govt all as directed by Engr-in-chrg. (iv) The MES No should be painted on indoor and outdoor unit with navy blue colour letters of size not less than 15 mm height. Drain pipe should be clamped up to plinth protection. No extra claim should be allowed for drain pipe from indoor unit to plinth protection of outside the building. (v) The quoted rates are also inclusive of making holes in brick/stone wall for installation of Air Conditioner and making good tothe exisitng surface with putty and paint in as specified and directed by Engr-in-charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
