Panchayat Raj Department has published Tender For Pradhaan Room Beautification And Other Works At Panchayat Samiti Chittorgarh District Chittorgarh. Submission Date for this Tender is 21-03-2024. Building Work Tenders in chittorgarh Rajasthan. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead:For thickness of tiles 10mm to 25mm. |
| 2 | ??????, ???????? ??????? ?? ?? ???? ??? ???? ????? ?? ???????? |
| 3 | Anti-termite treatment of existing floor and wall using Imidacloprid 30.5% EC non repellent, odorless, low dose, environimentally safe Termiticide with rapid action non corrosive stain free, by injecting the emulsion as per specification and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area. The pesticide emulsion of imidacloprid 30.5% EC mixed with water in the ration of 1:474 will be pumped by a motorized spray pump specified manner. The net floor and wall area treated will be measured for payment. |
| 4 | Providing and fixing calcium silicate board false ceiling at all heights including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the calcium silicate board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting of thickness of calcium silicate board as below:-) |
| 5 | ???? ??? ?? ?????? ????? ?????? ?? ?????? ?? ??????? ???? ??? ?????????? ?? ??? ?????? ?????? ?? ????? ??? ?????? ??? ???? ?????? ????? (?????????? ?? ???? ????? ???? ??)? |
| 6 | ???????? (?????????.??.) ?? ???????? ? 100 ???? ?? ?? ?? ?????? (?????) ????? ???? ? |
| 7 | 450X300 ???? ???? ?? ???? ???? ???? ?????? ?? ??? ???? (????????) ?? ?????? ???? ?????? ?????? ???? ???, 15 ???? ?? ????? ??? ??? 32 ???? ?? ???? ????? ?????? ?????? ??? 25 ???? ?????? ?? ?????? ???? ?? ?????? ???? ????? ? ?????????? ????? |
| 8 | ???? ???????/??? ???????/ ?????????? ??? ???????/ ??? ??? ??????? ?? ??? 1.5 ???? ??.??. ???? ?????? ??????????? ???? ?????????? ????? ??? ????? ??, ??????? ?????, ??????? ??????, ???????? ???? ?????? ??? 1.5 ???? ??.??. ???? ?????? ??????????? ???? ?????????? ????? ??? ????? ?? ?????? ???? ?????????????? ???/???? ?????? ??? ?????? ????? ?? ?????? ??????? ??????? ???? |
| 9 | Providing and fixing of uPVC casement fixed windows or ventilators manufactured in ISO 9001:2000 & 14001:2004 certified company. Frame : Made from the Extruded uPVC Window Profile Section of size 60 x 60mm having outer wall thickness of 2.25mm (+/- 0.2mm) and 3 box multi-chamber construction, White in finish, duly reinforced with 1.2mm thick G/J/U/O TYPE GI section. All the four corners shall be mitered cut & thermal welded so as to form window frame. Frame shall be milled with drain and air equalizer hole in order to be water tight and for drainage of accumulated water, if any, to outer side. Fix Mullion made of 76 x 60mm uPVC Profile Section with steel reinforcement shall be provided in windows as per the requirement. Frame shall have ‘O’ type EPDM gasket fitted in in-built groove of frame profile for proper air & sound insulation of the shutter. Glazing bead of size 34 x 20mm with ‘K’ & ‘O’ type inner and outer EPDM weather seal gaskets alongwith 5mm thick ISI make plain float glass.All welding joints of frame and shutter shall be cleaned and milled with the CNC mechanism to provide uniform grooved finish on all visible joints. Hardware : Installation at Site : Complete window is to be installed on site with 10 x 100mm fastners with white cap in existing pre-finished wall cut-out cemented to glass level plane at all height & width and silicon glue is applied to fill up the crevices between wall and window frame. Complete in all respect as per the drawing and specifications and direction of engineer-in-charge. |
| 10 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basicitem.)With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) |
| 11 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding. |
| 12 | Providing & Fixing Water Proof sunmika of approved Make Including Fixing charges Completer in all respect |
| 13 | Providing & Fixing Commercial Ply as per IS 710 : 1976 BWR of approved make for making wardrobe/shelves and other furniturewith fevicol & nails completeas per approved by engineer in charge. 18 mm thick |
| 14 | Providing & Fixing decorative veneer of approved make for inner/outer side of shutters with fevicol & nails completeas per approved by engineer in charge.4.0mm thick veneer |
| 15 | Providing and applyingMelamine polish on teak wood work of approved brand and manufacture to give an even shade with twoor more coats by compressor including sand papering,wood filler coat etc complete in all respect: |
| 16 | Providing and FixingCloth curtains Roman TypeIncluding Fixing and Curtain Rod complete in All respect |
| 17 | Supplying and fixing wood work in frames of wall panelling, false ceiling partition wall etc. as per approved design and drawing including antitermite treatment. |
| 18 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure "A":Commercial Veneer both side 30 mm thick . |
| 19 | Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails completeas per approved by engineer in charge.0.8mm thick mica |
| 20 | Providing and Fixing Charcol loovers 5" wide and 96" Height Including Fixing with Favicol and Nails or other Required Fitting Accessories for Wall Pannelingand other works complete in all respect. |
| 21 | Factory-readymade interior wall panel of thickness mentioned below. The panels shall have suitable provision for joining adjacent panels. Interior panels may have optional provision for inbuilt electrical conduit running lengthwise at vertical center of specified panels. The insulation core shall be self-extinguishing DIN 4102,Class B3 fire retardant class rigid PUR with thermal conductivity of 0.025 W/mK and with density of 40kg/m3 (+/-2kg) suitable for temperature range of -30 degree C to +80 degree C. The panel must be made using glue-free high pressure hot pressing self-bonding method and shall be free from major surface undulations. both sides of panel shall have a min15 micron protective plastic guard film to avoid scratches during transportation. 1. Panel shall be made of min 4mm (+/- 0.5mm) thick laminated wood based medium density fiber board sheet on both sides of rigid PUR insulation. |
| 22 | Spray painting in approved shade and approved qualitywith Duco paint of required colour to give even shade with two or more coats by compressor including sand papering, NC putty filler coat etc complete in all respect as per design given by Engineeer incharge on new work. |
| 23 | Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete |
| 24 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding |
| 25 | Providing and fixing bright finished Mortice lock of approved make Godrej or equivalent withpair ofCP handles for doors with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge. |
| 26 | Supply & Fixing of superior quality wall covering decorative paper of composition of paper and synthetic blend and providing material such as fevicol, cmc powder, chemical and water for fixing the wall paper as per enclosed photograph and direction Engineer-in Charge. |
| 27 | Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 28 | Providing And Fixing OF Led Light 20 Watt. Of Approved Make Making connection Suitable Including Fixing and Complete In All Respect. For Ceiling |
| 29 | Provision For Electricity Applicenes and Fitting |
| 30 | Charges For Interior Designing and Planning |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
