Zilla Parishad-ZP has published Construction Of Health Sub- Center At Village- Kauakhoh Block -Hariharganj Under Zila Parishad Palamu. Submission Date for this Tender is 11-03-2024. Building Work Tenders in palamu Jharkhand. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Earth work in excavation of foundation trenches in ordinary soil (vide classification of soil item -A ) and disposal of excavated earth as obtained to a distance up to 50 M. including all lift , leveling ramming the foundation trenches , removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I |
| 2 | Extra for earth work in hard soil (vide classification of soil –B) all complete as per specification and direction of E/l. |
| 3 | Filling in foundation trenches and plinth in layers not exceeding 150mm thick well-watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50M and lift of 1.5M all complete job as per specification and direction of E/I |
| 4 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l. (Mode of measurement compacted volume) |
| 5 | Providing designation 75B one brick flat soling in foundation, joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level 1:4:8 (1 cement :4 coarse sand (zone-iii) :8 graded stone aggregate 40mm nominal size) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement :1.5 coarse sand (zone-iii) :3 graded stone aggregate 20mm nominal size) |
| 8 | Reinforcement cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement :1.5 coarse sand (zone-iii) :3 graded stone aggregate 20mm nominal size) |
| 9 | Reinforcement cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases. above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement :1.5 coarse sand (zone-iii) :3 graded stone aggregate 20mm nominal size) |
| 10 | Providing Tor steel reinforcement as per approved design & drawing Providing Tor steel reinforcement of 8mm dia rods as per approved design & drawing (TMT Fe 500 only valid for SAIL & TATA Steel) |
| 11 | Providing Tor steel reinforcement of 10mm dia rods as per approved design & drawing (TMT Fe 500 only valid for SAIL & TATA Steel) |
| 12 | Providing Tor steel reinforcement of 12 to 20 mm dia rods as per approved design & drawing (TMT Fe 500 only valid for SAIL & TATA Steel) |
| 13 | Providing cantering and shuttering including strutting propping etc. and its removal after use in foundation work as per specification and direction of E/I Foundations, footings, bases for columns, etc for mass concrete |
| 14 | Columns, Pillars, Piers, Abutments, Posts, and struts |
| 15 | Lintels Beams, Plinths Beams, Girders, Bressummers and Cantilevers |
| 16 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc |
| 17 | Suspended floors, roof, landings, balconies and access platform |
| 18 | Providing designation 75B brick work in C,M, (1:6) in foundation and plinth with approved quality of coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials raking out joints to m15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 19 | Providing designation 100A brick work Fly Ash Brick (FALB) conforming to IS 12894-1990 (9”x4.5”x3”) in C.M. (1:6) in superstructure and plinth with approved quality of coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, scaffolding, raking out joints to m15mm depth, curing, taxes and royalty all complete as per specification and direction of E/l. |
| 20 | Providing designation 122mm thick reinforced designation 100A brick work Fly Ash Brick (FALB) conforming to IS 12894-1990 (9”x4.5”x3”) in C.M. (1:4) in superstructure and plinth with approved quality of coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, scaffolding, raking out joints to m15mm depth, curing, taxes and royalty all complete as per specification and direction of E/I |
| 21 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. sqm |
| 22 | Supplying fitting and fixing 35mm thick solid core type non decorative single leaf flush shutters in doors and windows with black board core bended with high quality phenol formal dehydes synthetic resign both side commercial veneered of stand make with oxidized iron fittings such as hinges tower bolts handle cleats and sand block and taxes all complete as per building specification and direction of E/l. |
| 23 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete: |
| 24 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 25 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 26 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 27 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 28 | Providing and fixing pressed steel door frames manufactured from commercial mild steel sheet of 1.60 mm thickness including hinges jamb lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm or base ties o f 1.60 mm pressed mild steel welded or rigidly fixed together by mechanical means adjustable lugs with split end tail 2.5 mm thick with mortar guards lock strike plate and shock absorbers asspecified and applying a coat of approved steel primer after pre - treatment of the surface as directed by in charge : Profile B Fixing with carbon steel glavanised dash fastener of required dia and size to be pade for separately |
| 29 | Supplying, fitting and fixing MS grill made of 20x6mm MS flat as per approved design and drawing properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site hoisting as per building specification and direction of E/l. (where materials is not supplied by the dept.) |
| 30 | Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20x10x2mm at 100mm centers and braced with M.S. flat diagonals 20x3mm with top and bottom rails of T. iron 40x40x6mm with 38mm dia steel pulleys complete withbolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage, hoisting and taxes all complete as per building specification and direction of E/l. |
| 31 | Supplying fitting and fixing glass panes including supplying putty, beats and nails after taking out old and broken glass panes and disposal of debris all complete as per building specification and direction of E/l. (5.5mm thick) |
| 32 | Providing and laying double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS 15622/ISO 13009 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 jointing with grey cement slurry @3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete size of tile 600x600mm |
| 33 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red.Area of slab up to 0.50 sqm |
| 34 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 35 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 36 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sands: 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade |
| 37 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 38 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 39 | Providing and laying 25 mm thick kotah stone slab flooring of approved quality over 19mm thick base of lime mortar (1:1:1)(lime putty: surkhi: coarse sand) laid andjointed with white cement slurry flush pointed with white cement including rubbing , polishing and cost of curing taxes and royalty all complete as per building specification and direction of E/I 600 x600 mm thick |
| 40 | Providing and laying 25 mm thick kotah stone in skirting of approved quality over 19mm thick base of lime mortar (1:1:1) lime putty: surkhi: coarse sand) laid andjointed with white cement slurry flush pointed with white cement including rubbing , polishing and cost of curing taxes and royalty all complete as per building specification and direction of E/I |
| 41 | Providing single layer Naria tiles in roof including cost of all labour and materials, taxes, and royalty all complete as per building specification and direction of E/I |
| 42 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase |
| 43 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sands: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 microns, finished with 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 44 | Water proofing for old roof slab. Protection of treated surface with PCC: -The treated surface should be covered with 25mm/50mm PCC of M-20 grade (1:1.5:3) with proper slope (1:120) towards the rain outlets in alternate panels …..do……do…… all complete as per |
| 45 | Covering of treated surface with PCC: - Providing 25mm thick cement concrete M20 (1:1.5:3) maintaining slope in alternate 2mtx2mt panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering and mixing cement concrete in mixer with admixture of integral water proofing and placing in position, striking curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 46 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 47 | Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 48 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 49 | Providing and applying white cement-based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 50 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 51 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 52 | Providing two coats of oil bound distemper of approved shade and make over a primer coat of whiting, over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty where required scaffolding washing of floors all taxes all complete as per building specification and direction of E/l. |
| 53 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly specification and taxes all complete as per building specification and direction of E/l. |
| 54 | Finishing walls with Acrylic Smooth exterior local Art paint of required shade, new work (two or more coat applied over and including priming coat of exterior primer applied, as per E/I |
| 55 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 56 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 57 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand including finishing the top smooth |
| 58 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 59 | Providing designation 75 B one brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/l. |
| 60 | Providing 12mm thick cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 61 | Providing 1.5mm thick cement punning, curing with all leads and lifts as per building specification and direction of E/l. |
| 62 | Sanitary and Water Supply Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c ing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of jointscompleteas per direction of Engineer in Charge. 20 mm nominal outer dia pipes |
| 63 | 25 mm nominal outer dia pipes |
| 64 | 32 mm nominal outer dia pipes |
| 65 | 40 mm nominal outer dia pipes |
| 66 | 50 mm nominal outer dia pipes |
| 67 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c ing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc 15 mm nominal |
| 68 | 20 mm nominal |
| 69 | 25 mm nominal |
| 70 | 32 mm nominal |
| 71 | Providing and fixing wash basin with C.I. rackets,15mm C.P brass pillar taps ,32mm C.P brass waste of standard pattern ,including painting of fittings and brackets,cutting and making good the walls wherever require: white viterous china wash basin size 550x400 mm with a pair of 15 mm C.P. brass taps |
| 72 | supplying fitting and fixing the following items complete with all materials as per specification and direction of E/I.(a) glass shelf with c.p brass rails.(i)600x125 mm glass shelf complete |
| 73 | Providing and fixing PTMT bottle trap for wash basin and sink bottle trap 31 mm single piece moulded with height of 270 mm ,effective length of tail pipe 260mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal,weighing not less than 260gms. |
| 74 | Providing and fixing PTMT liquid soap container 109 mm wide .125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105gms. |
| 75 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement approved quality and colour weighing not less than 88gms. |
| 76 | Providing and fixingC.P. brass bib cock of approved quality confirming to IS:8931 |
| 77 | Providing and fixingC.P. brass angle valve for basin mixer and geyser pointsapproved quality confirming to IS:8931(a) 15mm nominal bore. |
| 78 | providing and fixing toilet paper holders :C.P. brass |
| 79 | Supplying Polythene water storage tank of ISI mark (e.g. sintex/sinter.himgiri/gangotric etc.) with cover and locking system |
| 80 | Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A)580 mm long(a)with 10ltr lower level pvc cistern |
| 81 | Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(b) with 10ltrlow level pvc cistern |
| 82 | Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to 13592 Type A including jointin with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.(i) single socket pipes. 75 mm diameter |
| 83 | 76 mm diameter |
| 84 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A including jointin with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion 110 mm |
| 85 | single tee with door - 110x110x110 mm |
| 86 | Bend 87.5 |
| 87 | Shoe plain |
| 88 | Providing and fixing unplasticated PVC pipes of approved design -PVC rain water pipes by means of 50x50x50 mm hard wood plugs .screwed with m.s. serewes of requied length ,including cutting brick work and fixing in cement motar 1:4 and making good the wall complete . 75 mm diameter |
| 89 | 110 mm diameter |
| 90 | providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design |
| 91 | Electrical Supplying & drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface recessed steel/PVC condult as required. |
| 92 | Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit with modular type, Group C |
| 93 | Wiring for light/power plug with 4x4sq.mm FR PVC insulated copper conductor single core cable |
| 94 | Wiring for light/power plug with 2x4sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 2 no. 4 sq mmFR PVC insulated copper conductor single core cable for looping earthing as required. |
| 95 | Wiring for circuit/submain wiring alongwith earth wire -do- 2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 96 | 2x2.5 sq.mm + 1x2.5 sq.mm earth wire |
| 97 | 4x2.5 sq.mm + 2x2.5 sq.mm earth wire |
| 98 | 4x10 sq.mm + 2x6 sq.mm earth wire |
| 99 | Supplying and fixing of following size of pvc conduitalong with the accessoriesin surface/recess including cutting the wall and making good the same in case of recessed conduit as required 20 mm dia |
| 100 | 25mm dia |
| 101 | Supplying and fixing following modular type switch/ socket on the existing switch box/cover 5/6 amps, one way switch |
| 102 | 15/16 amps, one way switch |
| 103 | 5/6 amps, 3 pin socket outlet |
| 104 | 5/16 amps, 6 pin socket outlet |
| 105 | Tv antena socket outlet |
| 106 | Supplying and fixing batten holder including connection etc. as required. |
| 107 | Supplying and fixing 2 pin, 5 amps ceiling rose on existing junction box/ wooden block including connection etc. as required. |
| 108 | Supplying and fixing ding dong sound call bell single phase, 230 volts complete as required. |
| 109 | ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq.mm FRPVC insulated copper conductor single core cable etc. as required |
| 110 | installation of exhaust fan up 450mm sweep in the existing opening including making the hole to suit the size ,makin good connection ,testing,commencing etc, |
| 111 | S/F Modular type stepped tube electronic fan regulatoron the existing plate switch box including connection but excluding modular plate etc as required |
| 112 | S/F Modular blanking plate on theexcluding modular plate & switch box excluding modular plateetc as required. |
| 113 | supplying and fixing followingsizes/ modules,GI box alonwith modular base & cover plate for modular switches in recess etc as required 1 or 2 module (78mm x 78mmx 45mm)-for telephone & tv outlet |
| 114 | 4/5 module (78mm x 140mm x 50mm) |
| 115 | 6 module (78mm x 205mm x 50mm) |
| 116 | Earthing with copper earth plate 600mm x 600mm x 3mm thick Including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (but without charcoal or coke and salt) |
| 117 | Supply of 48" (1200 mm)Ceiling Fan Bajaj/Crompton or any other approved make 5 STAR rating 32 watt including wining the down rod of standardcomplete as required. |
| 118 | Supply of 12" (300 mm)Metal exhaust Fan Bajaj/Crompton or any other approved make etc |
| 119 | S.I.T.C. of following rating surface mounted LED tube lighting fitting suitable for 230V ,50 hz ,single phase supply etc. complete as 10/12W LED tube light |
| 120 | 20/22W LED tube light |
| 121 | S.I.T.C. of following rating recess /surface mounted LED round/square shape down light luminarie with pressure die cast housing for single phase supply voltagewith all necessary accessories as required .make havells/cormpotion /wipro/ philips. 18/20 W LED round down light (surface) |
| 122 | Bulk head fitting with 9/10 watt LED |
| 123 | Supply of XLPE insulated PVC sheathed ,heavy duty ,armoured electrical cable with aluminium conductor for working voltage upto and including 1100volts.(conforming to IS-7098.(part-1)4 core ,16sq. Mm |
| 124 | Providing and fixing 6SWG dia G.I wire on surface or in recess for loop earthing along with existing surface /recessed conduit /submain wiring /cable as required. |
| 125 | Providing and fixing 25mmX 5mmX G.I strip on surface or in recess for connections etc. as required |
| 126 | Supplying and fixing 20 amps, 240 volts, SPN Industrial type, society outlet, with 2 pole and earth, metalenclosed plug top along with 20 emos "C" curve , SP, MCB, in sheet stool enclosure, on surface or in receaswith choined metal cover for the socket out let and complete with connections lesting and commessioning etc. as required. |
| 127 | Supplying and fixing following ways hortzontal type three Pole and neutral sheet,MCB distribution board 415 volts on ------do---(but without MCB/RCCB/isolator) 8 way (4+24) Double Door Horzontal Type. |
| 128 | Supplying and fixing 6 Amp to 32 Amp rating 240 volts ,10 KA "C" Curve miniture circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections resting and comminising etc as required 6/32 Amp single pole |
| 129 | 40 amp TPN |
| 130 | Supplying AND Fixing single pole blanking plate in the existing MCB DB complete etc. as required |
| 131 | Supplying AND Fixing of following rating double pole (single pole & neutral ).240 volts,resudual current circuit breaker (RCCB),having a sensivity current 30 miliampere in the existing MCB DB complete with connections,testing & comminissioning etc as required. 40 Amps |
| 132 | BORE Well 200x165x125 mm borewell-supplying all materials, labours, tools & equipments for drilling -do-do all complete job as per direction of E/I From 0.00 m to 50.0 m |
| 133 | From 50.0 m to 100 m |
| 134 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, ittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia |
| 135 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested inapproved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 136 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: |
| 137 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. |
| 138 | S/F KIRLOSKER/CRI make 1.0HP submersible pump set having 100 m including all taxes royalty etc. all complete job as per direction of E/I |
| 139 | Carriage of Materials: - i) Bricks (8 Km) |
| 140 | ii) Sand (lead 10 Km) |
| 141 | iii) Stone Metal lead 22 KM |
| 142 | iv) Stone Chips (lead 22 Km) |
| 143 | Add 18 % GST |
| 144 | Add 1% Labour cess |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
