|
| 1 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) remaining serviceable tiles to stores and rubish off the premises all as specified and as directed. |
| 2 | Demolition of PCC in roof/floor etc (other than ground floor) beams, staircases, landing, chajjas and similar suspendedwork including taking down old roof treatment complete all as specified |
| 3 | Material and labourfor Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and directed. |
| 4 | Material and labourfor Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m complete all as specified and directed. |
| 5 | Material and labour forproviding cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate cast in situ asin roof kerbs/ sunken floors or mud stops, rounded or chamfered on edges, as directed including use of form work as necessary all as specified and as directed. |
| 6 | Material and Labour for Non-skid coloured joint free Ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not excceding 0.11 Sqm, in floors etc, set and jointed in cement mortar and pointed in white or coloured cement to match, laid over and including 20 mm thick screed bed in CM 1:4 complete all as specified and as directed. |
| 7 | Material and Labour for Non-skid coloured joint free Ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not excceding 0.18 Sqm, in floors etc, set and jointed in cement mortar and pointed in white or coloured cement to match, laid over and including 20 mm thick screed bed in CM 1:4 complete all as specified and as directed. |
| 8 | Material and labour for glazed ceramic coloured tiles 350x250x7mm / 450x350x7mm in vertical surface such as dados, set and jointed in neat cement slurry over and including backing coat of 10mm thick in CM 1:4 complete all as specified and directed. |
| 9 | Material and Labour for Vitrified tiles 10mm thick (square/rectangular) light coloured, area of each tile exceeding 0.36 sqm and not exceeding 0.42 sqm of any shade and any pattern (Pattern consists combination of two or more tiles ) in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed of 20mm thick in CM 1:4 complete all as specified and as directed. |
| 10 | Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 11 | Material and labour for 100mm thick plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregateas in sub base of floors including necessary form work all as specified and as directed. |
| 12 | Material and labour formachine pressed precast concrete interlocking paver block, any shape and size of 80mm thickness M-40 grade conforming to IS 15658-2006 with grey cement and pigment laid over 50mm thick cushion of river sand screen bed, compacted with mechanical surface vibrator complete all as specified and directed.Note: Sand cushioning will be measured and paid seperately. |
| 13 | Material and labour for precast cement concrete 1:3:6 type C10using 20 mm graded stone aggregate as in kerb, mud stop rounded or chamferred edges, set and jointed in CM 1:4 completeall as specified and as directed. |
| 14 | Material and Labour for 75mm thick Plain Cement Concrete 1:3:6 type C2 using40 mm graded stoneaggregate as in plinth protection, floors, pavings and hardstanding etc, finished even smooth without using extra cement etc including necessary forwork and filling the joints with sand and bitumen in 1:1 ratio complete all as specified and as directed. |
| 15 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid and bedded and pointed in any mortar all as specified and as directed. |
| 16 | Material and Labour for Granite 20mm thick ( of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and the like and laidover and including 20mm thick cement mortar 1 :4 including pointing in white cement using marble dust in 1:2 with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 17 | Taking down chowkats or frame exc 1.50 sqm each but not exc 4 sqm each with shutters (without taking off shutters from the frame ) complete all as specified and directed. |
| 18 | Taking down chokhats or frame not exceeding 1.5 sqm each with shutters (without taking off shutters from the frame ) complete all as specified and directed. |
| 19 | Taking down shutter of any description exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and as directed. |
| 20 | Supply and Fix PVC door frame size 50mm x 47mm made out of 5mm single sideprelam PVC sheet and edges will be painted to match with prelaminated sheetreinforced with MS square tube supplying& fixing in opening as per specification complete all as specified and directed. |
| 21 | Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plian colour PVC \"C\" channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement supplying and fixing in the frame at site as per specification & drawing of SSR Part II. |
| 22 | Material and labour forsecond class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with shine pinned at joints,fixed to wall and making good to wall all as specified and directed. |
| 23 | Supply and fix mild bands, stapes, supports for hold fast and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 24 | Supply and fixing 2nd class hardwood factory made plain framed panelled shutters 35mm thickwith lock rail and with panels of 12mm thick commercial veneered particleboard veneers on both side or with 9mm thick BWP commercial ply, size of members of shutters as specified in IS 1003-Part-I, kiln seasoned and chemically pressuretreated complete all as specified and asdirected. |
| 25 | Supply and Fix 1 st class HW glazed and skeleton shutters 35mm thk, open rebated and prepared to receive glass, gauze, etc. (withoutsash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. |
| 26 | Supply and fix Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including taking out worn out wire cloth complete all as specified and directed. |
| 27 | Supply and fix powder coated aluminium door and partition frame, Partition using standard aluminiumsection one or more rebates with joint clip and using rubber beading etc complete all as specified and directed.Note:Glass panel/particle board panel filling shall be measured and paid separately. |
| 28 | Supply and fix powder coated aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, and sliding tower bolt 150mm long anodised aluminium snap beading, screws etc. complete all as specified and as directed. |
| 29 | Supply and fix anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern of DG 102, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement, specified and directed. |
| 30 | Supply and Fixing5.5 mm thick sheet glass tinted in square exceeding 0.5 Sqm in each pane for fixing in aluminium joinery including necessary beading as specified and as directed. |
| 31 | Supply and fix 100mm long butt hinges medium weight mild steel cold rolled complete all as specified and as directed. |
| 32 | Supply and fix 75mm long butt hinges medium weight mild steel cold rolled complete all as specified and as directed. |
| 33 | Supply and fix in repairs aluminium handles fabricated type anodised of size 150mm complete all as specified and as directed. |
| 34 | Supply and fix in repairs aluminium handles fabricated type anodised of size 100mm complete all as specified and as directed. |
| 35 | Supply and Fix 150mm long aluminium anodised barrel tower boltall as specified and as directedby Eng-in-charge. |
| 36 | Supply and Fix 100mm long aluminium anodised barrel tower bolt all as specified and as directed by Eng-in-charge. |
| 37 | Supply and fixing aluminium alloy,anodised, sliding door boltof length 250mm with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded section or cast-aluminium alloy complete all specified and as directed. |
| 38 | Supply and fix Harrison rails, mild steel, chromium plated with fixing brackets stopsrollers etc. including taking out old railcomplete all as specified and as directed. |
| 39 | Supply and fix second class soft-wood (clean sawn) timber fixedin scantling including dismantling old unserviceable wood work complete all as specified and directed. |
| 40 | Supply and fix 2nd class soft-wood plain fillets, square, rectangular or triangular in section exc 13 and not exc 25 sq. cm clean sawn, secured with nails or brads including taking out old fillets complete all as specified and directed. |
| 41 | Supply and fix 2nd class softwood fillets bullnosed, splayed, chamfered or rounded on one edge or face, squares, rectangular or triangular in section exc 3 & n exc 6 sq cm fixed with screws including taking out old fillets complete all as specified and directed. |
| 42 | Supply and fix 18mm thich high density high moisture restistant (HDHMR) Board both side laminated of approved colour as in shutters , backboard, vertical support and horizontal shelves of kitchen / bedroom cupboards fixed with screw to timber framed work etc all as specified and directed. Note : Rate includes for all exposed edges/surface to be finished with same laminated sheet edge tap to match with the other surface |
| 43 | Supply and fix Cast brass powder coated automatic lock and release butt hinges of size 100mm complete all as specified and as directed. |
| 44 | Supply and fix Cast brass powder coated Box type decorative door handle of size 100mm complete all as specified and as directed. |
| 45 | S&F kitchen basket fabricated with stainless steel section (SS-304), best quality of size 430 mm x 508 mm x 200 mm for different use such as placing cup & saucer /cutlery glass/plate/ thali etc fixed in position with and including one pair telescopic Channelof size 450 mm (when closed), mild steel chromium plated, roller type, heavy duty as directed.Make :Asian sleek / Hettich |
| 46 | Material and Labour applying two coats synthetic enamel paint over one coat of pink primer on wooden surface any description over 10 cm in width or girth not otherwise described including preparation of surface etc., complete all as specified and directed. |
| 47 | Material and labour for preparation of old decorated wooden surfaces of any description exceeding 10 cm width or grith not otherwise specified and applying one coat of syntheic enemal paint all as specified and as directed. |
| 48 | Material and labour for preparation of old decorated surfaces of steel of any description exceeding 10 cm width or grith not otherwise specified and applying one coat of syntheic enemal paint all as specified and as directed. |
| 49 | Taking up or down steel tubing /CPVC pipe 15 mm bore including connections, cleaning for refixing or removal to storeall as directed. |
| 50 | Taking up or down steel tubing 20 mm bore including connections, cleaning for refixing or removal to storeall as directed. |
| 51 | Supplying and laying 16 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings after taking out unserviceable pipe complete all as specified and directed. |
| 52 | Supplying and laying 20 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings after taking out unserviceable pipe complete all as specified and directed. |
| 53 | Supply and fixing in repairsVitrious China squatting pan \" Orissa\"pattern of size 580 mm x 440 mm white with integral foot rest excluding flushing cistern and flush pipe including P or S trap making good the floor to match with existing floor complete all as specified and as directed. |
| 54 | Supply and fix in repair 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern low level, white, with inlet ball valve, float and handle including brackets, flushing pipe, 450mm long PVC Connection and connection to trap, and to flushing and making good to floor complete all as specified . |
| 55 | Supply and fix in repair plastic water closet seat cover, black or white, closed pattern with flat bottom, and cover and mild steel aluminised hinging device etc complete all as specified and directed. |
| 56 | Supply and fix Bowl with cistern for extended wall hung WC with PP soft close seat cover, hinges, Dual flush cistern, fitting, acesseries set Size 380x630x770mm JaquarCat part- CNS WHT-353SPPZ |
| 57 | Supply and fix Hand shower ( Health faucet) with 8mm dia 1.2 mtr long flexible tube and wall hook complete all as specified and directed.(Make: Cat part No: ALD 573 of Jaquar) |
| 58 | Supply and fix Toilet Roll Holder complete all as specified and directed.(Make: cat part No AKP-35751P of Jaquar) |
| 59 | supply and fix table topwash hand basin with fixing acesseries size 595x445x135mm complete all as specified and directed.(Make: jaquar cat part NoDS-wht-25931) |
| 60 | Supply and fix single lever basin mixer without popup waste system with 450 mm long braided hoses complete all as specified and directed.(Make: Jaquar cat partNo VGP-81051B ) |
| 61 | Supply and fix Single lever 3 inlet Divertor Exposed parts kit Cat part No Jaquar ALI 85193K Consisting of Operting lever, wall flange & buttonf only suilatbe for ALD 193 complete all as specified and directed. |
| 62 | Supply and fix Conceled Body for 3 inlet Single lever diverter with button assembly cartridge sleeve but withoutor Exposed parts complete all as specified and directed. (Make: Jaquare cat part No ALD 193) |
| 63 | Supply and fix Overhead shower dia 180mm round shape single flow with air effect (ABS body & Face plate Chrome Plated) with Rubit Cleanign System complete all as specified and directed. (Make: Jaquar cat part No OHS-1755) |
| 64 | Supply and fix Soap dish holder complete all as specified and directed. (Make: Jaquar cat part No ACN-1131N) |
| 65 | Supply and fix Glass Shelf 550 mm longcomplete all as specified and directed .(Make: Jaquar cat part No AQN 7771) |
| 66 | Supply and fix Corner glass Shelf with bracketcomplete all as specified and directed. (Make: Jaquar cat part No ACN-1173) |
| 67 | Supply and fixing in repairsbevelled edge Mirror of selected quality glass 5mm thick fixed on commercial plywood and wooden pluges with CP Brass Screws ,Studs & cup washers all as specified and directed. |
| 68 | Supply and fixBrass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified. |
| 69 | Supply & Fixing in repairs Bib taps, 15mm bore, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed. |
| 70 | Supply and Fixing in repairs stop valves/angle cock, 15mm bore, fancy type, with long shank & cut concealed typechromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 71 | Supply and fix in repair 15mm dia PVC connection with PTMT nuts and PVC washers 45 cm long and connecting of water pipes all as specified and directed. |
| 72 | Supply and fix in repairs grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gm) complete all as specified and directed. |
| 73 | Supply and fixin repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratary with plugs, washers and wastes incl bedding in CM on to dwarf walls, or incl fixing cantelever brackets & connecting union to pipe overall size 915 mm x 460 mmbowl size, 410 mm x 330 mm x 160 mmincluding waste Pipe all as specified and as directed. Make: Blue Star/Nirali/Diamond/ Pheonix. |
| 74 | Supply and fix PVC pipe (SWR) single socketed in any length with rubber ring joint 110mm dia fixed to wall complete all as specified and as directed. |
| 75 | Supply and fix PVC pipe (SWR) single socketed in any length with rubber ring joint 75mm dia fixed to wall complete all as specified and as directed. |
| 76 | Supply and fix PVC (SWR) bends 110mm with access door complete all as specified and as directed. |
| 77 | Supply and fix PVC (SWR) bends 75mm with access door complete all as specified and as directed. |
| 78 | Supply and Fix PVC (SWR) junction single 110 mm bore, (single T) equal or unequal with access door complete all as specified and as directed. |
| 79 | Supply and fix in repairs 75mm PVC (SWR) branch piece , single (Double Y) equal or unequal all as specified and as directed. |
| 80 | Supply and fix in repairs PVC (SWR) vent cowl 110 mm bore equal or unequal complete all as specified and directed. |
| 81 | Supply and fix in repairs PVC (SWR) vent cowl 75 mm bore equal or unequal complete all as specified and directed. |
| 82 | Demolition of brickwork or stone/boulders masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 83 | Material and Labour for providing precast cement concrete type C1, 1:3:6 (20 mm graded stone aggregate) solid blocks exc 10 cm in width and setting in cement mortar 1:4 complete all as specified and as directed. |
| 84 | Taking down cement plaster on brick or stone/concrete walls etc including raking out joints, hacking for key, scrubbing down with water etc of any description complete all as specified and directed. |
| 85 | Material and labour for rendering 15mm on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair without using extra cement complete all as specified and directed. |
| 86 | Material and Labour for rendering 10mm thick on fair faces of concrete work in CM 1:4,using water proofing compound @3% by weight of cement, finished even and smooth without using extra cement complete all as specified and as directed.Note: Water proofing compound shall be measured separately |
| 87 | Supply only integral water proofing compound all as specified and as directed. |
| 88 | Material and Labour for preparing of new surfaces of any description and applying two coats of acrylic distemper, white or tinted over a coat of primer after applying one or more coat of wall putty to achieve smooth surfaces on plastered wall surface complete all as specified and as directed. |
| 89 | Material and labour for compelete removal of existing surface of old surfaces of walland applying two coat of acrylic distemper tinted over a coat of primer complete all as specified and as directed. |
| 90 | Material and labour forpreparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed. |
| 91 | Material and labour for compelete removal of existing surface of old surfaces of ceiling and applying two coat of white wash complete all as specified and as directed. |
| 92 | Material and labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 93 | Excavating in trenches, n exc1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil getting out complete all as specified and as directed. |
| 94 | Material and labour for plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete including necessary form work complete all as specified and as directed. |
| 95 | Demolition and breaking up 150mm bore drain pipes (RCC pipe/Salt glazed wareor Reinforced concrete) set in cement mortar including haunching and removing debris to a distance exc 1.5Km and n.exc 5Km all as specified and as directed. |
| 96 | Material and Labour for PCC 1:3:6, type C-2 as in concrete bed to drain pipes including packing under and completely surrounding pipes after they are laid and tested for 150mm diapipe and testedcomplete all as specified and as directed. |
| 97 | Supply and laying Reinforced cement concrete hume pipes class NP2, laid and jointed complete with one collar per length of pipe, dia 150 mm complete all as specified and as directed. |
| 98 | Material and Labour for TMT(CRS/HCR) bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wires (annealed) not less than 0.9 mm dia or secured with clips complete all as specified and as directed. |
| 99 | Material and labour for Precast reinforced cement concrete 1:3:6 type C1 using 20mm graded stone aggregateas in cover slabs of man holes including necessary form work, placed in position, set in CM 1:4 complete all specified and as directed. |
| 100 | Returning, filling in soil including spreading leveling, watering and well ramming in layers n.exc.25cm thick complete all as specified and as directed. |
| 101 | Removing excavated material / soil to a distance n.exc 50m away and depositing where as directed at a level n.exc 1.5m above the starting point, complete all as specified and as directed. |
| 102 | Material and labour for Plain cement concrete 1:3:6, type C2, using 40mm graded stone aggregate as in surface channels and drains including necessary form work all as specified and as directed. |
| 103 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms moulds, mitred/stopped ends etc complete all as specified and directed. |
| 104 | Dismantling of water tanks of capacity exceeding 500 ltrs and not exceeing 1000 ltrs capacity and removing from site complete all as specified and as directed by Engineer-in-charge. |
| 105 | Supply and fix Rotational moulded Polyetheylene Water Storage Tank 500 Ltr capacity Triple Layer (Cylinderical verticle with closed top) including 15mm dia GI Medium Grade 200mm long overflow and wash out pipe each with all required fittings, Checknut, Stopper etc complete hoisted and fixed in position, including all incoming and outgoing connection of GI pipe complete and including 20mm PTMT Ball valves high pressure wiith epoxy coated aluminium rodand high density plastic ball screwed for iron pipe complete for 15mm dia pipe (Minimum weight 15mm-142 gms/each) fixed on roof top complete all as specified and directed. |
| 106 | Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for unreinforced complete all as specified and as directed. |
| 107 | Material and Labour for rendering 10mm thick on fair faces of concrete work in CM 1:3 mixed with integral water proofing compound @ 3% by weight of cement or as per manufacturers instruction, surface finished even & smooth without using extra cement including curing the plastered surface complete all as specified and directed. NOTE: Water proofing compound shall be measured and paid separately. |
| 108 | Material and labour for plain cement concrete 1:2:4 type B0using 12.5 mm graded stone aggregate as in kerb, mud stop rounded or chamferred edges including use of form work as necessary completeall as specified and as directed. |
| 109 | Material and labour for applying oil based bitumen primer conforming to IS 3384-1986 at 0.20 kg/Sqm on prepared surface and applying of one coat of blown grade hot bitumen 85/25 conforming to IS 702 @ 1.20 kg / sqm and applying roof treatment with APP modified waterproofing membrane weighing not less than 3kg/sqm, reinforced withnon woven polyster matt weighing not less than 160 gm/sqm having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 650N/Sqm cm, tearing strength of 180N(Minimum), applied bytorch-on application including minimum 10 cmover lap and 15 cm end lap and applying of one coat of blown grade hot bitumen 85/25 conforming to IS 702 @ 1.20 kg / sqm over the membrane and then applying solar reflective bituminous aluminiumpaint for thermal insulation @ 0.10 kg/sqm complete all as specified and directed. NOTE:All necessary safety measures shall be ensured by the contractor during execution of work at site and quoted rate shall be deemed to be inclusive of the same. |
| 110 | Material and labour for roof tiles, Mangalore pattern, interlocking at side laid dry complete all as specified and as directed. |
| 111 | Material and Labour for cement mortar band in CM 1:4 of size width 70mm at bottom 25mm at top and 40mm thickat 30 cm centre to centre for laying of mangalore pattern tiles complete all as specified and directed. |
| 112 | Supply and fix Steel rolling shutters 1.25mm thick, width of lath 75 mm with and including ball bearing, manually operated type as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position including taking out old shuttercomplete all as specified and as directed. |
| 113 | Supply and fix stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement including taking out old railing complete all as specified and directed. |
| 114 | Schedule of Credit (Minus) Rs.70335.50NOTE: Bidder shall insert credit amount of Rs. 70335.50 as ratein Green field under Col-13. |
