Building Construction Department-BCD has published Tender For Proposed Construction Of Van Bhawan At Chaibasa In The District Of West Singhbhum For The Year 2023-24. Submission Date for this Tender is 16-02-2024. Building Work Tenders in chaibasa Jharkhand. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l. |
| 2 | Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume). |
| 3 | Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume). |
| 4 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including" cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume). |
| 5 | Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 6 | Providing designation 75 B brick work in C.M.(1 :6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 7 | Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l. |
| 8 | Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 9 | Providing 112mm thick reinforced designation 100A brickwork fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:4) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including the cost of screening carriage of material scaffolfing raking out joint to 15mm depth curing taxes and royalty (but excluding the cost of reinforcement ) all complete as per building specification and direction of E/I. |
| 10 | Extraforbrick workfor eachconsecutive floor abovefirst floor including watering and scafolding, all complete as per direction of E/l. |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size) |
| 13 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 14 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:1½:3 (1 cement:1½ coarse sand:3 graded stone aggregate 20 mm nominal size) |
| 15 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). |
| 16 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. |
| 17 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 18 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 19 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcementwith 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 20 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 21 | Foundations, footings, bases of columns, etc. for mass concrete |
| 22 | Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 23 | Suspended floors, roofs, landings, balconies and access platform |
| 24 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 25 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 26 | Stairs, (excluding landings) |
| 27 | Weather shade, Chajjas, corbels etc., including edge |
| 28 | Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l. |
| 29 | Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l. |
| 30 | Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. TMTFe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL). |
| 31 | Providing Tor steel reinforcement of 10mm. ,12mm & 16mm dia. bars as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. |
| 32 | (a) 10mm TMTFe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL). |
| 33 | (b) 12mm TMTFe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL). |
| 34 | (c) 16mm TMTFe 500 ( Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd.. Bokaro, and Vizag (RINL). |
| 35 | Providing Tor steel reinforcement of 20mm. 25mm. 28 mm, 32mm dia. bars as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. |
| 36 | Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.) |
| 37 | Supplying , fitting and fixing callapsible gate of apporoved size and make properly fabricated with vertical double channels 20x10x2 mm. at 100mm. Centres and braced with M.S flat diagonals 20 x 3 mm,with top and bottom rails of T. iron 40x40x6 mm with 38 mm dia steel pulleys complete with bolts nuts, locking arrangements stoppers, handles, including applying a primer coat of led paint carriage hosting and taxes all complete as per building specification and direction of E/I. |
| 38 | Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l. (where steel is not supplied by the deptt.) |
| 39 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l. |
| 40 | Providing 12 mm cement plaster (1:3) with clean coarse sand of F.M 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curring, taxes and royalty all complete as per building specification and direction of E/l. |
| 41 | Providing and laying Double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less then 0.08% and conforming to IS: 15622/ISO 13006 of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 Coarse sand0, jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with wite cement and matching pigments etc, complete Size of tiles 600 x 600 mm. |
| 42 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curingwithall leadsand liftsof water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 43 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curingwithall leadsand liftsof water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 44 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5including screening, curingwithall leadsand liftsof water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 45 | Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l. |
| 46 | Providing 25 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 47 | Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/l. |
| 48 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l. |
| 49 | Supplying, fitting and fixing 30mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l. |
| 50 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification) |
| 51 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l. |
| 52 | Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l. |
| 53 | Water proofing for old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flextble material brush, roller or spray for water proofing coating per manufacturer Specifications with following steps :-(a)surface preparation .-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing (loose paint / coating, and cement laitance by cleaning with compressed air water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage leakage. On identification of seepage cement grouting to be donewith non shrink expanding admixture of Sika India Pvt.L.td.) MYK Schomberg / Dr Fixiti/ Fosroc or equivallent. Providing and reparing of all Corner and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150Mrn X 150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic pc?" lymer of Sika/ Fosroc/MYK Schomberg/Dr1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent.,Befor "Chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar-including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.(b)lst Coat :- Apply 1st coat of two component acrylic modified, ready to use, flexible cementitiot.is material on surface saturated dry roof and inside wall of Parapet.Wall upto 600 mm by brush or roller . After 1st coat of application , 45 gsm of Fibre glass cloth to lay when the first layer is still green. 1st coat shOUld be applied @1.50 kg/Sqmt/coat. For the purpose of measurer-11609-1"e entire treated surface will be measured." (c) 2nd Coat :-To apply the 2nd coat of two component acrylic modified read to use, flexible cementtiOus material right angle to the 1st. coat over the glass fibre laid surface: 2nd coat-,should be applied @ 0.7 Sqmt/coat. For the purpose of measurement the entire treated surface will be measured." After three days of drying the 2nd coat , the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Water proofingBrand:- Sika Topseal 109hi / Fosroc Brushbond RFXI Dr. Fixit Pidiffin 2K / MYK Aquafin TG . Product Performance - Chemical Base Part A: Acrylic copolymer, Part B: Specially graded cementitious powder - Density 1.6 kg/I (mixed density) at +27°C Tensile Strength -2Nimm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout BondSiren th -2 f\l/mm2 concrete failure Accordin" to ISO4624) Slant-Shear Bond Strength -4 Nimm2 (According to FIP 5.15) Elongation at Break -35% Without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370) (d) )Protection of treated surface with PCG :- The treated surface should be covered with 25mm/50mm F"CC of M-20 grade (1.1.5:3). with proper slope ( 1:120) towards the rain outlets in alternate panels of 2 mt x 2 mt keeping 6 rnm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 co of 100 ml per bag of of cement to be added in the screed concreie(paid separately.for this items).All corners shall be chamfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface should be packed prorSeqswith ridti:corict"ete and the peripheral mouth to be sealed with,moisture insensitive epoxy putty of. Sika India .Pvt.Ltd. / MYK Schornbefg /Dr Fixit/Fosroc .For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCCsurface should be filled with POlysulphide Sealant.(Paid Separately). Be d - Sika India Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc . Warranty for five years. |
| 54 | Covering of treated surface with PCC:-providing 25 mm thick Cement Concrete M20 (1:1:5:3) maintaining slope in alternate 2 mtx 2mt panels With approved quality of stone chips of 20mm to 6 mm size graded andCleaned sand of F.M.2.5 to 3 including screening, shuttering, and mixing Cement concrete in mixer with admixture of integral water proofing and Placing in position, striking curing, taxes and royalty all complete as per Building specification and direction of E/I. Panels that has been left should Be casted next day. There should be 6 mm gap between panels .brand-Sika _ plastocrate plus, MYK proof WP 10, Fosroc- ConplastX 421 ic DrFixit Pidiproof LM+ |
| 55 | Providing and mixing liquid integral water proffing compound in conctrete of plaster as manufacturer specification and as per direction of engineer in charge. Brand. Sika plastocrate plus, MYK proff WP 10, Fosroc-Conplast x 4211C, Dr.Fixit, Pidiproff LW+ or Equivalent |
| 56 | Providing and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysuiphide Sealant (Porin.g Grade)as per drawings and technical specificationsi6nd direction of E in Charge. (with 18% GST) B rand Sika Polysulphide, Fosrpc-Thioflex 600 Dr. Fixit Pidiseal PS(42P. MY K Seal PS or Euivalent. |
| 57 | Cost of Driling 200mm x 165mm x 125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. |
| 58 | (a) From 0.00 M to 50.00 M below G.L. |
| 59 | (b) From 51.0 M to125.00 M |
| 60 | Supplying submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 metre submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP |
| 61 | Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase50hz with no coil. Over load element , On _OFF pushbuttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914. F.A.S.D starter 10 H.P |
| 62 | Supply fitting and fixing GI pipe 50 mm Dia (TATA or equivalent make) Medium Quaility as per IS:1239 ( part 01 ) 2004 |
| 63 | Supplying chemical emulsion in sealed containers including delivery as specified.-Chlorpyriphos emulsifiable concentrate of 20% |
| 64 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:-With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 65 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 66 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 67 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth |
| 68 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 69 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin-Charge. |
| 70 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC "C" channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the "C" Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer"s specification & drawing. 30 mm thick pre laminated PVC door shutters |
| 71 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile C Fixing with adjustable lugs with split end tail to each jamb |
| 72 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 73 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 74 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 75 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 76 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding pointing the joints with white cement and matching pigments etc., complete. |
| 77 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 78 | 75 mm diameter |
| 79 | 110 mm diameter |
| 80 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 81 | Coupler 75 mm |
| 82 | Coupler 110 mm each |
| 83 | Single pushfit Coupler 75 mm |
| 84 | Single pushfit Coupler 110 mm |
| 85 | Single tee with door 75x75x75 mm |
| 86 | Single tee with door110x110x110 mm |
| 87 | Single tee without door 75x75x75 mm |
| 88 | Single tee without doo 110x110x110 mm |
| 89 | Bend 87.5° 75 mm bend |
| 90 | Bend 87.5° 110 mm bend |
| 91 | Shoe (Plain) 75 mm Shoe each |
| 92 | Shoe (Plain) 110 mm Shoe |
| 93 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm |
| 94 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin-charge and as per manufacturer"s specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60 |
| 95 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spacedjoints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 96 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 97 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 98 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 99 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 100 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 101 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 178 mm |
| 102 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia |
| 103 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia |
| 104 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 105 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore |
| 106 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
| 107 | Providing and fixing C.P. brass Stop Cock (concealed) of standard designand of approved make conforming to IS 8931 15mm nominal bore, approved brand C.P. fittings. |
| 108 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore |
| 109 | Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole |
| 110 | Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gm |
| 111 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 112 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.15 mm nominal bore with 45 cm length |
| 113 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 gms |
| 114 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc |
| 115 | 15 mm nominal dia Pipes |
| 116 | 20 mm nominal dia Pipes |
| 117 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work |
| 118 | 25 mm nominal dia Pipes |
| 119 | 32 mm nominal dia Pipes |
| 120 | 40 mm nominal dia Pipes |
| 121 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe |
| 122 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe |
| 123 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :-450 mm dia. R.C.C. pipe |
| 124 | Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg |
| 125 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 126 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) and For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 127 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 128 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 129 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia |
| 130 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia |
| 131 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 132 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 133 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 134 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia |
| 135 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.200 mm clamp |
| 136 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings forthe specified design loads conforming to IS 875 part III (the systemmust passed the proof test at 1.5 times design wind pressure withoutany failure), including functional design of the aluminum sections forfixing glazing panels of various thicknesses, aluminium cleats, sleevesand splice plates etc. gaskets, screws, toggles, nuts, bolts, clampsetc., structural and weather silicone sealants, flashings, fire stop(barrier)cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections andprofiles etc. to accommodate 3 Dimentional movement for achievingperfect verticality and fixing structural glazing system rigidly to theRCC/ masonry/structural steel framework of building structure usingstainless steel anchor fasteners/ bolts, nylon seperator to preventbimetallic contacts with nuts and washers etc. of stainless steelgrade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealantand one part weather silicone sealant compatible with the structuralsilicone sealant of required bite size in a clean and controlled factory/ work shop environment, including double sided spacer tape, settingblocks and backer rod, all of approved grade, brand and manufacture,as per the approved sealant design, within and all around theperimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet1 mm thick and of sizes, shapes and profiles, as required as per thesite conditions, to seal the gap between the building structure andall its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters thecurtain glazing system to make it watertight, by incorporatingprinciples of pressure equalization, providing suitable gutter profilesat bottom (if required), making necessary holes of required sizesand of required numbers etc. complete. This item includes cost of allinputs of designing, labour for fabricating and installation of aluminiumgrid, installation of glazed units, T&P, scaffolding and other incidentalcharges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified.The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer,dully approved by Engineer-in-charge. The item also includes thecost of all mock ups at site, cost of all samples of the individualcomponents for testing in an approved laboratory, field tests on theassembled working structural glazing as specified, cleaning andprotection till the handing over of the building for occupation. In theend, the Contractor shall provide a water tight structural glazing havingall the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified,as per the approved shop drawings and as directed by the Engineer-in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadowboxes, extruded aluminium section capping for fixing in the groovesof the curtain glazing and vermin proof stainless steel wire meshshall be paid for separately under relevant items under this sub-head. However, for the purpose of payment, only the actual area ofstructural glazing (including width of grooves) on the external faceshall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted onstructural glazing system if area of structural glazing exceeds 2500Sqm from the certified laboratories accreditated by NABL(NationalAccreditation Board for Testing and Calibration Laboratories),Department of Science & Technologies, India. Cost of testing ispayable separately. The NIT approving authority will decide thenecessity of testing on the basis of cost of the work, cost of the testand importance of the work. Performance Testing of Structural glazingsystem Tests to be conducted in the NABL accredited lab or any other accreditation body which operates in accordance with ISO/ IEC 17011 and accredits labs as per ISO/IEC 17025 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing methodfor a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME-331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static airpressure test (1.5 times design wind pressure without any failure) asper ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240kpa (35psi) upto 2000 ml |
| 137 | Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement |
| 138 | Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- inCharge |
| 139 | Providing and fixing Sink Cock with Swinging casted spout |
| 140 | Carriage of materials from source to site work including loading & unloading all complete job as per specification and direction of E/I |
| 141 | Earth |
| 142 | Sand |
| 143 | Aggregate |
| 144 | Stone Metal |
| 145 | Brick |
| 146 | Fly Ash Brick |
| 147 | Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) With "P" trap (a)10.0 lit. low level PVC cistern |
| 148 | Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) 580 mm long (c) with 10.0 lit. low level P.V.C. cistern |
| 149 | Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l. Flat back or standing corner (600mmx x350mm) |
| 150 | Supplying, fitting and fixing C.P. brass towel rail 20mmX600mm with bracket container |
| 151 | Supplying, materrials and labour for constructing inspection chamber of designation class 75B brick size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I. |
| 152 | Wiring for Light point/fan point/exaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in recessed PVC conduit, with modular type switch , Modular plate, suitable G.I boxes and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required . ( Havells/C&S/HPL/Legrand/Anchor/ Polycab) Group-C |
| 153 | Power Plug Wiring in PVC conduit (2x4 sq. mm): Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 154 | Circuit / Sub-main wiring in PVC Conduit:Wiring for circuit / sub-main wiringalong with earth wire with thefollowing sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required. |
| 155 | 2x1.5 Sqmm + 1x1.5 sqmm earth wire for separate 3 pin 5A sockets |
| 156 | 2x2.5 Sqmm + 1x2.5 sqmm earth wire for switch board |
| 157 | 4x6 Sqmm + 2x6 sqmm earth wire- |
| 158 | 4x10 Sqmm + 2x6 sqmm earth wire for power MCB DBs |
| 159 | Wirilg in cxisting conduit :- Supplyingand drawing following sizes of FR PVC insulated copper lconductor single core cable in existing zurface / recessed steel / PVC loonarit including dismantling as required-3x4 sq.mm |
| 160 | SITC of 2 Pair unarmoured PVC staircase cables of conductor size 0.5 sq.mm annealed tinned electrolite grade copper , PVC insulated twisted pairs bunch togeather over all PVC sheathed , Laid on tray or along the wall or laid in pipes or in trenches including excavation of cable trench, sand filling covering with bricks and back filling complete as required. Make: Polycab/ Finolex/ Deltron/Havells/Anchor/Molex/Schenider |
| 161 | Supplying and fixing of following sizes of medium class PVC conduit along with acessories in surface/ recess including cutting the wall and making good the same as required. |
| 162 | 20 mm |
| 163 | 25 mm |
| 164 | 32 mm |
| 165 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required |
| 166 | 5/6 A switch on switch board |
| 167 | 3 pin 5/6 A socket outlet on switch board |
| 168 | S/F Modular type switch socket - Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required RJ11 Telephone outlet |
| 169 | Supplying and fixing Modular type blanking plate-Supplying and fixingmodular blanking plate on existing modular plate switch box excluding modular plate etc. as required. |
| 170 | S/F Modular boxes, base & cover plate - Supplying and fixing following size/modules G.I. box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 module (78mm x 78mm x 45mm) |
| 171 | S/F light plug point with modular type accessories - Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc. as required . (For light plugs to be used in non residential buildings) |
| 172 | S/F power plug point with Modular type accessories - Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface of in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch connection, painting etc. as required. (For light plugs to be used in non residential buildings) |
| 173 | S/F Ceiling Rose: Supplying andfixing 2 pin 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 174 | S/F Electronic Musical Call bell: Supplying and fixingelectronic musical call bell suitable for D.C/A.C, single phase 230 volt, complete as required. |
| 175 | ITC fluorescent fitting directly on surface :- installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, directly on ceiling / wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor. |
| 176 | Supplying and fixingthe follwing way Three Pole pole and Neutral Sheet steel M.C.B distribution board, 415 volts in recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, hinged front acrylic cover from MCB Knob detachable gland plate, interconnection including earthing etc. as required(without MCB/RCCB/Isolator). Make-Havells/ Legrand/ Polycab/ C&S/ Hager/ABB / HPL /Anchor |
| 177 | 4 way(4+12) Double door Horizontal type for Power DBs |
| 178 | 6 way(4+18) Double door Horizontal type (Lighting=4 nos+power=8 nos) |
| 179 | S/F "C" series SP MCB: Supplying and fixing 240 volts, "C" series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required. |
| 180 | 6/32A Single Pole |
| 181 | 32A TPN |
| 182 | 63A TPN |
| 183 | Supplying and laying25mmx5mm GI earth strip in Ground: Supplying and laying25mmx5mm GI earth stripat 0.50 metre below ground as strip earth electrode, including soldering etc as required. |
| 184 | Providing and fixing earth bus 25mmX5mm GI strip on surface for connections etc. as required. |
| 185 | Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 kV grade of following size direct in ground in the same trench including excavation, but excluding sand cushioning protective covering and refilling the trench etc as required of following sizes.-upto 35 sq.mm |
| 186 | Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 95 sq.mm. but not exceeding 185 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 187 | Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 95 sq.mm. but not exceeding 185 sq.mm. direct in groundin the same trench one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 188 | LED Floodlights 120W :Environmental friendly, new generation,aesthetically designed, ultra modern LED floodlightluminaire with high diecast housingand IP66 protection.( make: Wipro /Havells/Bajaj/ Philips) |
| 189 | Down Lighter 7W : Supply, installlation, testing and commissioning of Environmental friendly, new generation, aesthetically designed, square LEDdownlighterluminaire with pressure diecast housingand toughened glass IP66 protection with supply voltage 100-270V, 50Hz, AC. Luminaire shall confirm to IS: 10322 Part-5/Section-2or IEC: 62722 and shall be complete with all necessry accessories as required. ( Make: Wipro/ Havells/Bajaj/ Philips) |
| 190 | Recess mounted 20W LED round :Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness 20W LEDs as light source.( make : Havells /Bajaj/ Wipro) |
| 191 | Panel 18W LED(1"x1") :Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling.( make : Havells /Bajaj/ Philips/Jaquar) |
| 192 | Panel 36W LED(2"x2") :Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling.( make : Havells /Bajaj/ Philips) |
| 193 | LED tube with Batten 20W : Supplying and fixingof wall mountedLED 20W tube + batten and electronic driverand accessories as required. ( Make -Wipro/Bajaj / Havells/ Philips) |
| 194 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 195 | MV Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 1100V grade with Termination and Laying of cable. Make:- Finolex / Polycab / Havells / Universal-3.5 Core 35 Sq mm main panel to external feeder pillar |
| 196 | Providing of PVC/ XLPE insulated sheathed heavy duty armoured power cable with aluminium conductor of 1.1kV (confirming to IS-1554 part-1) Make-Havells/ Finolex/ Polycab/Mescab/KEI.-3.5CX70 sq. mm armouredAL Cable for DG supply +AC panel |
| 197 | Providing of PVC/ XLPE insulated sheathed heavy duty armoured power cable with aluminium conductor of 1.1kV (confirming to IS-1554 part-1) Make-Havells/ Finolex/ Polycab/Mescab/KEI.-3.5 Core 185 Sq mm for DG supply to main panel(2 run for each DG) |
| 198 | MV Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 1100V grade with Termination and Laying of cable. Make:- Finolex / Polycab / Havells / Universal-4 Core 10 Sq mm (For external lights) |
| 199 | Supply of Metal Exhaust Fan 12"(300mm): Supply of12"(300mm), 230V ACmetal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required( Make- Polar/Bajaj/ Havells/Crompton) |
| 200 | Supply of Wallmounted Fan: Supplyof 16"(400mm), 230V AC wall/cabin fan including fixing the bracket, making , connection testing, commissioning etc as required( Make- Polar/Bajaj/ Havells/Crompton) |
| 201 | Bulk head 9/10 LED Fitting: Supply and fixing of 9/10W LED, surface mounted bulk head PVE water proof housing forindoor/ ourdoor.( Make-Havells /Bajaj/Wipro/Philips) |
| 202 | 82.5kVA DG set :Supply, fitting, fixing, errection and commissioning along with civil foundation work of 82.5kVA D.G. Set, 415 Volts, 3 Ph. Silent Diesel Engine driven generating set as per IS:1460 & IS : 13018 and alternator as per IS:13364 complete with sound proof company make canopy (Acoustic Enclosure suitable for 82.5 kVA D.G. Set.) with breaker panel (automatic Control Panel) and civil foundation work as per the norms of 100 KVA Silent D.G. Set with suitable arrangement for Al./Ar./C etc as required. (Make:- Sterling and Wilson Powergen Private Limited with MTU Engine SDGSC - 3 Cotroller / Kirloskar (GREEN) / Jakson Limited / Mitsubishi / Cater Pillar) |
| 203 | SITC of 3 Phase Online 40 KVA UPS Preffered Make-Vertiv/GUTUR/APC/Numeric |
| 204 | 3 core PVC insulated PVC sheathed copperconductor flat submersible cable. Supplying , Flat flexible submersible cable with ,copper conductor , PVC insulated and PVC sheathed as IS:7098 3 Core 4 Sq mm. Copper wire |
| 205 | MS Battery Rack suitable for 30 to 35 UPS Battery installation |
| 206 | SITC of 12V, 65 Ah SMF Battery, with 24 months replacement-VRLA- AGM maintenance -free,26520VAH |
| 207 | Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination withcompression gland & bimetalic lugs,and support etc.complete as required.-3.5 × 50 sq.mm.(aluminium) |
| 208 | Supplying and fixingmetal box of following sizes(nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required-100 mm X 100 mm X 60 mm deep |
| 209 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required- 2 Run CAT6 UTP Cable (for Network only . (Make:Legrand/Panduit/Molex/RIT/Siemon) |
| 210 | 1.1kV Cable End Termination: suppluingand fixingindoor cable endterminationwith brass double compression gland and AL lugsof following sizeAl armoured cables. |
| 211 | 3.5 Core 35Sq mmarmoured AL(32mm) |
| 212 | 3.5 core 70 Sq mm |
| 213 | 3.5 core 120 Sq mm |
| 214 | Supply, installation, balancing and commissioning of factoryfabricated GSS sheet metal rectangular/ round ducting complete with neoprene rubber gasket, elbows, spilleter dampers, vanes, hangers, support etc as per approved drawings and specifications of following sheet thickeness complete as required. |
| 215 | 24G,Thickness0.63mmsheet |
| 216 | 22G,Thickness0.80mmsheet |
| 217 | Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required |
| 218 | 24G,Thickness0.63mmsheet |
| 219 | 22G,Thickness0.80mmsheet |
| 220 | Supply, installation, testing and commissioning of Motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for integration within AHU room-Damper |
| 221 | Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications. |
| 222 | Supply, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications-200 mm dia |
| 223 | Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications |
| 224 | Supplying, installation, testing and commissioning of microprocess basemain fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required. Make:Honeywell/ ASES/ Qutak/ Bosch |
| 225 | Supplying, installation, testing and commissioning ofoptical type Smoke detector and mounting base with LED light complete as required. Make:Honeywell/ ASES/ Qutak/ Bosch |
| 226 | Supplying, installation, testing & commissioning of response indicator on surface/recessed having two LED with cover complete with all connections etc as required |
| 227 | Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required.Make:Honeywell/ ASES/ Qutak/ Bosch |
| 228 | Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required. Make:Honeywell/ ASES/ Qutak/ Bosch |
| 229 | Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc. |
| 230 | 80 mm diameter |
| 231 | 100 mm diameter |
| 232 | 150 mm diameter |
| 233 | Providing and fixingcheck valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc. |
| 234 | 80 mm diameter |
| 235 | 100 mm diameter |
| 236 | 150 mm diameter |
| 237 | Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. |
| 238 | Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour. |
| 239 | Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required. |
| 240 | Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete. |
| 241 | Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903 |
| 242 | Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required. |
| 243 | Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge. |
| 244 | 150 mm diameter |
| 245 | 100 mm diameter |
| 246 | 80 mm diameter |
| 247 | 25 mm diameter |
| 248 | Supply, Installation, Testing and Commissioning of electric driven, Centrifugal or Submersible type, single/multistage, end suction type, centrifugal/submersible pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motorssuiitable for operation on 3 phase, 415 volts 50 Hz AC supplywith IP 55 protection for enclosurewith F class insulation confirming to IS: 325 includingcommon base frame fabricated from min. 75X50 mm M.S channel, coupling with guard foundation bolts, pressure gauge, anti-vibration pads, cement concrete foundation etc. complete in all respect as required or as directed by engineer incharge.Make:PEW/Kirloskar |
| 249 | Main fire pump |
| 250 | Jockey pump 450 LPM, 35 M head |
| 251 | Terrace Booster Pump |
| 252 | Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, having switchgears and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V,3 phase 50 HZ AC supply with enclosure protection class IP 42 with 400 Amp aluminium bus bar as required. Make:SAM/L&T/Havells-A) Fire pumps panel -Incoming a)1 No. 200 Amp, TP&N MCCB b)0-400 Amp digital ammeter with one set of current transformer c)0-500 volt digital voltmeter with RYB indicator lamps, HRC control fuses. Outgoing I a)1 Nos of 200 Amp TP&N MCCB (1 No for EDFP ) b)1 Nos of (suitable for 40 HP pump) DOL starter with over load protection, current sensing type single phase preventer with all accessories and internal wiring complete as required for automatic operations (1 No for EDFP) c)1 sets 0-400 Amp digital ammeter and 1 sets current transformers. d)1 sets of selector switches for auto / manual operation, Local / Remote / OFF and ON / OFF / TRIP indications. II a) 1 Nos of 63 Amp TP&N MCCB (Jockey pump) b)1 No of (suitable for 12 HP pump) HP DOL starter with over load protection, current sensing type single phase preventer with all accessories and internal wiring complete as required for automatic operations c)1 set of 0-63 Amp digital ammeter and 1 set current transformer. d)Selector switches for auto / manual operation, Local / Remote / OFF and ON / OFF / TRIP indications. Note:- Potential free terminal to be provided for BMS |
| 253 | Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . Outdoor unit (High Ambient Machine)-24HP capacityX6 units=144HP |
| 254 | Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. |
| 255 | 4 TR |
| 256 | 3.4 TR |
| 257 | 2.8 TR |
| 258 | 2 TR |
| 259 | 1.8 TR |
| 260 | Refrigerant Piping: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : |
| 261 | 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation |
| 262 | 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation |
| 263 | 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 264 | 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 265 | 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 266 | 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 267 | 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 268 | 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 269 | 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 270 | Embankment Construction with Material Obtained from Borrow Pits (Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2) Rolling with smooth wheeled roller |
| 271 | Granular Sub-base with Close Graded Material (Table:- 400-1) By Mix in Place Method (Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) for grading- IIMaterial |
| 272 | Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.) |
| 273 | Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.90 kg/sqm using mechanical means. |
| 274 | Tack coat Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom. |
| 275 | Dense Graded Bituminous Macadam (Providing and laying dense bituminous macadam with 100- 120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5% by weight of total mix of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver inisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 507 complete in all respects.) with VG-30 Grade Bulk Bitumen.for GradingII(19 mm nominal size) |
| 276 | Bituminous Concrete (Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 % of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 509 complete in all respects) for Grading-II(10 mm nominal size) |
| 277 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.) |
| 278 | Retro- reflectorised Traffic signs (Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing 80 mm x 60 mm rectangular ) |
| 279 | Non- Schedule items Providing and fixing Paneles Door Frame 12 mm Ply wood (Green/Optima/Red) , Veneer fininsh with all taxes and royalty all complete as per E/I. |
| 280 | Panel for ACs: Supplying, designing, manufacturing, installation, testing and commissioning of panel fabricated out of 2mm thick(14SWG) CRCA sheet steel, dust and vermin proofwith reinforcement of suitable size iron channel of suitable size with proper lifting arrangement effecting proper connection of all incomer and out going (IP-43) fully compartmentalized cubical type wallmounted, totally enclosed, switch board and suitable for use on 415V, 3 phase, AC Supply, 4 wire, 50 C/S, system having 25 kA fault capacity, housed with incoming and outgoing aluminum bus bars, interconnection, interlocking between feeders etc. with indicating lamps, push buttons, necessary accessories, all out goingfeeders protectionas required.-The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for multi runs aluminum cables for all MCCB. Panel shall have individual compartment with name plate. Panel Size - As per Drawing and shall be provided at the time of work order- The Name Plate for each incoming & outgoing feeder must be in Anodized Aluminium Sheet. BUS BARS SECTIONS The panel includes 415V, 300A, 3Ph, 25kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects.The current density of bus bar shall be minimum 0.8 A /sq.mm. Al. Bars up to 63A capacity. Otherinter connections shall be made with 2.5 and 4 Sq mm PVC Cu. wire. The panel consisting of the followings 4 pole MCCB 200 A,35 kA with fixed thermal magnetic setting 4 pole MCCB 40 A/63A,16 kA with fixed thermal magnetic setting+ spare 200 amps, 4 pole Changeover 300 amp 415 V heavy duty three phase with neutral busbar chamber 32 A DP MCB,C, CURVE Indicator switch Selector switch Voltmeter Ameter C.T. Coil |
| 281 | Panel for UPS: Supplying, designing, manufacturing, installation, testing and commissioning of panel fabricated out of 2mm thick(14SWG) CRCA sheet steel, dust and vermin proofwith reinforcement of suitable size iron channel of suitable size with proper lifting arrangement effecting proper connection of all incomer and out going (IP-43) fully compartmentalized cubical type wallmounted, totally enclosed, switch board and suitable for use on 415V, 3 phase, AC Supply, 4 wire, 50 C/S, systemwith incoming and outgoing aluminum bus bars, interconnection, interlocking between feeders etc. with indicating lamps, push buttons, necessary accessories, all out goingfeeders protectionas required. -The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs BUS BARS SECTIONS The panel includes 415V, 200A, 3Ph, 25kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects.The current density of bus bar shall be minimum 0.8 A /sq.mm. Al. Bars up to 63A capacity. Otherinter connections shall be made with 2.5 and 4 Sq mm PVC Cu. wire. The panel consisting of the followings 4 pole MCCB 125 A,16 kA with fixed thermal magnetic setting for UPS and Fire fighting pump 40 A TPN MCB for lighting DBs 200 amp 415 V heavy duty three phase with neutral busbar chamber Indicator switch Selector switch Voltmeter Ameter C.T. Coil |
| 282 | Advanced New Generation ESE (Early Streamer Emission) Air TerminalLightning Conductor -:Supply, installation, fixing, fitting, testing and commissioning,ofadvance new generation early streamer emission technology lightning arrester of type DMSGI-45 with Level-1 protection of 63m radius. Device is confirming to standard NF C 17-102. Device shall be mounted at least 5 meter clear to highest point by support-mast of 40 mm dia GI pipe duly galvanized with minimum 85 micron zinc coating with foundation to suit mast, for Level 1 protection of 63 m (as per NFC 17-102 & IEC 60-1:1989.) radius with accessories complete as required for all other structures and designated open spaces covered by general area lighting mast on which ESE (Early Streamer Emission)can be installed similar to OPR 30 with active system.The Insulation material used to electrically isolate the panels shall be comprised of a base polymer which provides high ozone & UV resistance with di-electric strenght of 24-38 kV/mm tested as per NFC 17-102 & IEC 60-1:1989. The ESE terminal shall not contain any electronic circuits or any moving parts for its operation. The ESE terminal shall be tested & certified by CPRI (Central Power Research Institute, Govt of India) for the Impulse current of 45 kA (8/20 micro sec) with 5 positive & 5 negative impulse. The ESE (Early Streamer Emission) terminal shall be approved by DGMS (Director General of Mines Safety), Govt of India. Make:- ABB/Altec Corporation/Ingesco.- The above advanced New Generation Lightning Arrester with ESE Technology consist of following items:- Air Terminal:- Providing of Early Streamer Emission Air Terminal made of pure Stainless Steel grade A316 double layer (DIN 4301) Mast:- Providing of Extension supportMast made of 40 mm dia class A GI Pipe duly galvanized with minimum 85 micron zinc coating with foundation to suit Mast, for Level 1 protection of 63 Mtr. radius(as per NFC 17-102 & IEC 60-1:1989.), with accessories complete as required for all other structureslike couplers, guywires to fix the mast to the building /structure at highest point such that the Air terminal is 5 meters above the tallest structure including supporting 1.25 m FRP Mast. (as per NFC standard)and properly secured in a vertical position Lightning Flash Counter :- Poviding fitting fixing and testingofLightning Flash Counter (Search / Strike counter) (6 Digit Display) , suitable for 10kA- 100kA (250A) to be installed on one of the down conductors approximately 5 Mtr. from the ground level. It registers every lightning discarage intercepted by the air terminal as direct lightning protection. Testing Joints:- Poviding, fitting, fixing of testing joints to belocated just below the lightning counter on the down conductor from the earthing system in order to faciliate periodical checking of earthing resistivity. Protective Sheath :- A 3 inch dia approximately 3 Mtr long plastic pipe is fitted at the ground level to prevent accidental shocks to human beings/animals during a lightning discharge. The product specificationsofabove EARLY STREAMER EMISSION LIGHTNING CONDUCTOR SYSTEMshall beas follows:- Material - Stainless Steel 316 (DIN 4301 Weight -2.9 Kgs Length- 55cm (including the rod). Width - 12.5 Cm. |
| 283 | Tripod Earthing System for ESE (Early Streamer Emission) technology Lightning Conductor- (3 Nos. for per set):-Supply, errection,fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for Tripod chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing) Make :- OBO/ Satcom/ Ingesco/ Prolite Each CHEMICAL EARTHINGfor Tripod Earthing shall have following details:- Supply of Pollution free Earthcon Compound 25Kg (or 2 bags of 12.5 Kg each) Supply of 17.2 mm dia,250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed). Supply of stainless steel "U" Bolt Clamp. Supply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton) Total Costfor Tripod Earthing System for ESE technology Lightning Conductor- (1 Set = 3 Nos. Chemical Earthing as tripod Earthing for ESE Lightning Arrester) |
| 284 | Supply, fitting, fixing, connecting and testing of 24-port 10/100/1000T and 100/1000 SFP combo stackable switch with 4 SFP+ ports and dual power supply, Switching Capacity 280Gbps and Forwarding Rate 214.3Mpps, 2GB DDR SDRAM, 256MB flash memory, Route maps and redistribution (OSPF, BGP, RIP), Supports up to 64K MAC addresses, SDN or similar kind of technolgy should support,Switch should support link reccovery within 50ms for Ring architecture, All switches, AP, FO Module , Access Points aand WLAN Controller should be from the same OEM, Warranty 5 year from Day 1.(Make:- Cisco - WS-C3850-24XS / Allied Telesis -Model No. AT-x930-28GSTX / Juniper - EX4300)-The above L3 Managed Data Switch consists of the following:- 1. Power cord India, right angle. 2. Both side Cable connector. 3. 1 year free service pack. Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports Switching Capacity/Forwarding Rate :- 280Gbps/214.3 Mpps Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Routing:- IPv4 static routing and RIP. Fail-over:- Switch capable of recovery within 50ms in a ring for application high availability IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6 Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN) Standard Protocol:- IEEE 802.1Q,IEEE 802.1w,IEEE 802.1s,IEEE 802.1p,IEEE 802.1AB,IEEE 802.1AX,IEEE 802.3ad Operating Temparature:- 0°C to 50°C Certification:-EMC: EN55022 class A, FCC class A, VCCI class A, ICES-003 class A Immunity: EN55024, EN61000-3-levels 2 (Harmonics), and 3 (Flicker) Safety-Standards: UL60950-1, CAN/CSA-C22.2 No. 60950-1-03, EN60950-1, EN60825-1, AS/NZS 60950.1,Certification: UL, cUL, TUV, (RoHS) Compliance-EU RoHS compliant,China RoHS compliant Warranty:- 5 Years. |
| 285 | 24 x 10/100/1000T ports and4 x 100/1000X SFP ports, L2 Switch , Switching Capacity56Gbps and Forwarding Rate 41.7Mpps,operating temperature 0°C to 50°C, Switch should support link reccovery within 50ms for Ring architecture, SDN or similar kind of technolgy should support, Warranty 5 year from Day 1 . Make:- Cisco - WS-C9300L-24T-4G/ Allied Telesis - Model AT-x230-28G / Juniper - EX2200-24)-The above L2 Managed Data Switch consists of the following:- 1. Power cord India, right angle. 2. Both side Cable connector. 3. 1 year free service pack. Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports Switching Capacity/Forwarding Rate :- 56Gbps/41.7Mpps Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Routing:- IPv4 static routing and RIP. Fail-over:- Switch capable of recovery within 50ms in a ring for application high availability IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6 Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN) Operating Temparature:- 0°C to 50°C Certification:- EN,UL and RoHS Warranty:- 5 Years. |
| 286 | Supply, fitting, fixing, connecting and testing of switch with 24 x 10/100/1000T PoE ports and4 x 100/1000X SFP ports, PoE+ L2 Switch , Switching Capacity56Gbps and Forwarding Rate 41.7Mpps, Switch should support PoE and PoE+ with 370W minimum power budget, operaating temperature 0°C to 50°C, Switch should support link reccovery within 50ms for Ring architecture, SDN or similar kind of technolgy should support, Warranty 5 year from Day 1 . Make:- Cisco - WS-C9300L-24P-4G / Allied Telesis -AT-x230-28GP / Juniper - EX2200-24P)-The above L2 Managed Data Switch consists of the following:- 1. Power cord India, right angle. 2. Both side Cable connector. 3. 1 year free service pack Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports Switching Capacity/Forwarding Rate :- 56Gbps/41.7Mpps Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN, Routing:- IPv4 static routing and RIP. Fail-over:- Switch capable of recovery within 50ms in a ring for application high availability IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6 Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN) Standard Protocol:- IEEE 802.1Q,IEEE 802.1w,IEEE 802.1s,IEEE 802.1p,IEEE 802.1AB,IEEE 802.1AX,IEEE 802.3ad Operating Temparature:- 0°C to 50°C Certification:- EN,UL and RoHS Warranty:- 5 Years. |
| 287 | SITC ofGigabit Fiber Module-SM, (Make:- Cisco/ Allied Telesis / Juniper) |
| 288 | SITC of Wireless Access Point as per detailed specification below (Make:- Cisco -/Allied Telesis/ Juniper -)-The access point should be capable to offer IEEE 802.11ac Wave 2 standard with an assured throughput 1.1 Gbps or more. Should support dual band as 2.4 or 5GHz with embedded antenna Support IEEE 802.11a/b/g/n/ac 2x2 MIMO The AP should be operated in standalone as well as controller-based environment. Should have feature to create multiple virtual AP on the same physical device to configure the different security policies for each virtual AP Should have feature to allocate the equal bandwidth for all the connected users to ensure consistent performance for all users AP should be offering automatic channel selection to restrict interference Should support Multiple BSSIDs, VLAN tagging Should support automatic channel selection to avoid overlapping of the channel Support RF load balancing to increase the performance Should have feature to configure virtual blanket assigning particular channel for the selected AP’s for seamless connectivity. Should have to work with single channel and multi-channel architecture on the same AP’s simultaneously to get best of both architectures Should have option Band Steering and support 802.11k, 802.11v, and802.11r for Fast roaming Should have mechanism to detect the rogue AP and client isolation Should support Authentication, Accounting and 802.1x, WPA, MAC address filtering, SSID hiding or ignoring and Neighbor AP detection Should support the mechanism to Hide and ignore/restrict for specific SSID CE, RCM, FCC,Wi-Fi certified, UL60950-1,EN 55024, EN 55032, EN 61000-3-2, EN 61000-3-3, EN 61000-4-2, EN 61000-4-6, EN 61000-4-11 Should be operated as 802.3at or 802.3af standard Should be offered with min 5 years replacement warranty with proper back-up on respective-OEM letter Head. The switches, AP and FO Modules should be from the same OEM. OEM should be in Gartner"s Magic quadrant in the latest Gartner report for Wired and wireless LAN. (Report should be attached along with the Bid |
| 289 | SITC of Wireless Controller Software along with license for 30 Access Points to be installed on the industry standard Server/workstation PC or Hard controller;The detailed specification in Annexure 1 of this APis a part a necessary part of the BOQ (Make:- Cisco -/Allied Telesis/ Juniper -) |
| 290 | 12 Port LIU Switch : SITC of 12 Port Loaded LIU with SC Unit for 6 SM fiber Single mode fibres SM (2 Nos. ofLoaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 12 Fiber Capacity & 12 Nos. of SC Pigtail - Pigtail 1 Meter SM (Make:Legrand/Panduit/RIT/Siemon) |
| 291 | 24 Port LIU: SITC of 24 Port Loaded LIU with SC Unit for 24 SM fiber (4 Nos. ofLoaded Duplex adapter with Adapter plate) along with 1Pc of Splice Tray - 24 Fiber Capacity & 24 Nos. of SC Pigtail - Pigtail 1 MeterSingle Mode (Make:Legrand/Panduit/RIT/Siemon) |
| 292 | SITC of Fiber Duplex Patch CordsLC-LC SM Patch Cord 2 mtr. (Make:Legrand/Panduit/RIT/Siemon)-Cable : LC-LC 9/125µm OS2 Singlemode Duplex Patch Cord Length : 3mtrs Connectors : The optical fiber patch leads shall comprise of Single mode 9/125µm fiber with 2XLC type fiber connectors terminated at each end of fiber patch cord. Insertion loss should be better than 0.35 dB Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2 Attenuation: 1310/1550 : 0.36/0.22 dB/KM Connector Loss : 0.30dB(max) Operating Temperature : -40°C to +75°C |
| 293 | SITC of 6-Core SM Armoured Fibre Optics Cabl-e in Mtrs: (Make:Legrand/Panduit/RIT/Siemon)-The fiber should be optimized for operation at 1310 nm and at 1550 nm. Should fulfill the requirements of ISO.IEC 11801 - 2nd Edition, type OS2, ITU-T REC G 652D spec IEC 60794-1-2 F5 Fibre Count : 6 /12 Fiber count per tube :6 / 12 Filler count :4 Filler Material : PP Max. Attenuation: At 1310 nm <= 0.36 dB/km, At 1550 nm <=0.22 dB/km Fibre/Tube Identification : Multi Tube Fibre protection (Tubes) : Polybutylene Terephthalate (PBT) Armouring : CST Thickness : 1.6mm Outer Sheath :UV Stabilised Polyethylene (PE) Central Strength Member: Steel wire coated with PE Water Blocking : Thixotropic Gel (Tube); Petroleum Jelly (Interstices) Cable Diameter (D) : 9.0 ± 0.5 mm Mass (Nominal) : 91 kg/km Min. Bending Radius (during Installation) : 20 D;D-Outer Diameter Max. Tensile Strength-Short Term : 1500N Max. Crush Resistance-Short Term : 2200N/100 mm Operating Temperature range : -40°C to +70°C |
| 294 | SITC of 24 port UTP jack panel (24 portRJ-45 Loaded CAT-6 UTP 19" rackmountable patch panel preferbaly with 6 blocks). (Make:Legrand/Panduit/RIT/Siemon)-Patch panel should be modular design, populates up to 24 UTP keystone-type jacks in 1U Patch panel should be Enhanced with cable strain relief with retention tray; It should be single metal both front panel and rear tray Material: sub-rack made of MS Steel with dimension 44.4 mm :482.6 mm : 105 mm (h:w:d) tray Information Outlet or connectin module should comply with the specification mentioned above in 2 Standard : Conforms to IEC-60603-7 (603-7) for keystone-type, snap-on apertures Should be RoHS complied |
| 295 | SITC of Straight LAN Patch Chord-3 Mtr (Make:Legrand/Panduit/RIT/Siemon) |
| 296 | SITC of Straight LAN Patch Chord-1 Mtr (Make:Legrand/Panduit/RIT/Siemon)-Standardization: Compliant with Cat.6, Class E requirements: ISO/IEC 11801 2nd Edition Compliant with Cat.6 component standards IEC 60603-7-4 and 60603-7-5 Cable shield: U/UTP Number of conductors : 8 Stranding: 7 x 0.20 mm (24 AWG) Cable jacket characteristics: cable, metal-free Cable overall diameter: 6.5±0.2 mm Tube / Wire type: stranded conductor Insulation: solid polyolefin, 0.97±0.02 mm diameter Plug: Feature cable retension, with enhanced pull strength Cat 6 patch cord plug to have round cable holder and strain relief boot to avoid bending. Jacket: PVC with 8 different color options Plug should have high repeatability cross talk performance |
| 297 | SITC of white modular plate type Single front plate for 1 Nos. RJ 45 Dataoutlet (Make:Legrand/Panduit/RIT/Siemon)-Should be UK style Keystone-type Faceplates are available in 1, 2 & 4 port configurations Should be featured with shutter options, the screws not to be visible Should support Work with both Flush and Wall mount box Should support Operating Temperature: -10~+60; Storage Temperature: -40~+68; Humidity: 15%~90% RH Material: ABS, UL 94V-0; Spring: SUS304; Surface Finish: Polished |
| 298 | SITC ofRJ 45 Data Module to be fixed on face plate (Make:Legrand/Panduit/RIT/Siemon)-RJ45 Jack of Category 6, for the establishing of transmission channels of class E with up to 4 plugged connections, complies with Category 6 requirements of the standards ISO/IEC 11801:2nd edition, EN 50173-1, DIN EN 50173-1: 2002 as well as ANSI/TIA/EIA 568-B.2-1, de-embedded tested in acc. with IEC 60603-7 (603-7), interoperable and backwards compatible with Cat.5e and Cat.5 Suitable for 10GBase-T applications in acc. with IEEE 802.3an up to 500 MHz and 55 m. Compatible with RJ standard plugs (RJ11, RJ12, RJ45), PCB- and tool based connection of installation cables AWG 24 – 22 (0.5 mm – 0.65 mm) and flexible cables AWG 26/7 – AWG 22/7. IDC termination should feature nil crossover in acc. with EIA/TIA 568-A/B, gold-plated bronze contacts for >750 mating cycles, >200 insertion cycle Material: RoHS complied Housing material: Polycarbonate (UL-94-V0) Should be available with or without dust protection feature Should be 3P certified |
| 299 | Splicing of Armoured SM/MM Fibre Optics Cable: Splicing, testing and commissioning of supplied, OFC cable of 6-Core Armoured Fibre Optics |
| 300 | SITC of Fully Loaded 1U 19" 600*600 Wall Mounted Rack with all required accessories -2 Nos. of Fan,6A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ; Preffered Make-Legrand/APW/President/Valrack |
| 301 | Providing, fixing, fitting, installation and testing of 42 U Network Rack as server cabinet 19" LCS2 along with all standard accessories, 800mm (W), 1000mm (D), CRCA "D" grade 1.6mm thick sheet, pwoder coated for cabinet , 4mm Toughened Tinted Glass Door and along with following accessories:-1. Cooling fan 220/230V AC, of 90 CFM--4 Nos. ,2. Cable manager Metal 4 Nos. 3. PDU- 230V /AC 1 No., 6. Mounting Hardware (20 Sets of M-6 screws, washers,cage, nuts (Nickle Coated)-3 Nos. ,7. Earthing strips copper 150mm H 1 No.8. Door Lock 1 No. ,9. Caster Wheels (with breake) 2 Nos.10. Caster Wheels (without breake) 2 Nos. ,11. Front Metal Band 1 No.(Preferred Make-Valrack/President/Rittal |
| 302 | SITC of EPABX SYSTEM: IP based 100% non-blocking EPABX System should be a IP Compatible with rich feature set of the system and can be connected with pure Voice over IP (VoIP) communication network across corporate Local and Wide Area Networks (LAN and WAN) as & when required.Central Processing Unit: The system main software should be open architecture based. The CPU of main system shall be 32 bit processor working at 2.0 GHz or better.The system should be rack mountable. • System Architecture should be latest pure IP and should be wall Mountable ? Meet-me conference 30 party X 2from day 1 must be available. Must Support Unified Communications Equipped with 128 Analog Extensions expandable upto 384 Extensions,8 Analog Trunk Ports, 1 PRI with one IP Phone to be Used as Opertor Console with 6DSS Keys, 02 Ports Auto Attendant,EPABX Make: Avaya/NEC/Unify |
| 303 | Analog BasicCLI Push Button Telephone: SITC of analog telephone- Make: Panasonic/ BPL/Beetel |
| 304 | SITC ofTelephone Tag Block):IP-65( weather proof). Preffered Make-Krone |
| 305 | 50 pair krone Box fully loaded without IPM |
| 306 | 300 Pair krone Box fully loaded without IPM |
| 307 | IPM |
| 308 | SITC of multi-core telephone jelly filled armoured PVC cables of conductor size 0.5 sq.mm annealed tinned electrolite grade copper , PVC insulated twisted pairs bunch togeather over all PVC sheathed , Laid on tray or along the wall or laid in pipes or in trenches including excavation of cable trench, sand filling covering with bricks and back filling complete as required. Make: Polycab/ Finolex/ Deltron/Havells/Anchor-50 Pair |
| 309 | SITC of white modular plate type Single front plate for 1 Nos. RJ 45/RJ11 Data/Voiceoutlet (Make:Legrand/Panduit/RIT/Siemon) |
| 310 | Supply, fitting, fixing, commissioning and testingof 25Sq. MM Copper Conductor Multi strandPVC Sheilded FRLS Wire with suitable Copper LUGS for Battery Interconnection and suitable 35 Sq. mm copper wire of 4 length of 10 mtrs each for UPS to Battery excluding cable from PANEL to UPS and UPS to panel. Make- Polycab/Havells/KEI |
| 311 | Chemical Earthing-Supply, errection,fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing) -Each chemical earthing shall have following details:- Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each -Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed).Supply of Stainless Steel "U" Bolt Clamp,Supply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton) |
| 312 | 4MP IR Bullet Fixed Camera -1/2.8"Progressive Scan CMOS, 2688 × 1520 at 25fps, 2.8 mm Fixed lens, 0.01Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified.Preferred Make- Axis/Pelco/Dahua |
| 313 | 4MP IR Indoor Dome Fixed Camera -1/3" Progressive Scan CMOS, 2688 × 1520 at 25fps, 2.8mm Fixedlens, 0.01 Lux at F1.2, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, IK10, Alarm & Audio: 1 input & 1 output, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Audio exception detection, video tampering, UL, CE, FCC certified.Preferred Make- Axis/Pelco/Dahua |
| 314 | IP Fixed Mini Dome Camera: 1/2.7" Progressive Scan CMOS, ICR,0.01 lux at F1.2, 0 lux with IR, 1920x1080:25fps, 2.8mm Fixed Lens, H.265, MJPEG, Three individually configurable stream, IK08, IP66, DC12V & PoE, 120dB WDR, 3D DNR, BLC, Support on-board storage up to 128GB (SD card not included), Alarm -1 input,1 output, IR range: up to 10m, Edge Anlalytics- Line crossing detection, intrusion detection, Motion detection,face detection, video tampering, UL, CE, FCC certified. Preferred Make- Axis/Pelco/Dahua |
| 315 | SITC of4MP 35× Network IR PTZ Camera with Dual-sensor, 1/1.8" progressive scan CMOS,Full-color image output,Up to 2688 × 1512 resolution,Min. illumination:Color: 0.0005 Lux @(F1.5, AGC ON),B/W: 0.0001 Lux @(F1.5, AGC ON),0 Lux with IR, 35× optical zoom, 16× digital zoom, 120 dB WDR, 3D DNR, HLC, BLC, EIS, Chromatic Defog, Support H.265+/H.265 video compression, Support rapid focus, Deep-learning-based target classification algorithm for auto-tracking 2.0 and perimeter protection, Up to 250 m IR distance. Smart IR, Rain-sensing auto wiper, IP67,White Balance-Auto/Manual/ATW (Auto-tracking White Balance ) /Indoor/ Outdoor/Fluorescent Lamp/Sodium Lamp,Lens 5.9mm to 206.5 mm, 35× Optical, Zoom Speed-Approx. 4.4 s (optical lens, wide-tele),Field of View-Horizontal field of view: 58.9° to 2.2° (wide-tele),Vertical field of view: 35.3° to 1.2° (wide-tele),Diagonal field of view: 65.9° to 2.5°(wide-tele),Working Distance-10 mm to 1500 mm (wide-tele),Aperture Range-F1.6 to F4.4, Movement Range (Pan) 360° endless, Perimeter Protection-Intrusion, Line Crossing, Region Entrance, Region Exiting, Support alarm triggering by specified target types (human and vehicle),Filtering out mistaken alarm caused by target types such as leaf, light, animal, and flag, etc.,Event Detection--Unattended Baggage Detection, Object Removal Detection, Face Detection, Audio Exception Detection,Motion Detection, Video Tempering Alarm, Exception (HDD Full, HDD Error, Illegal Login, IP Address Conflict, Network Disconnected),Smart Tracking-Manual Tracking, Auto Tracking (support tracking specified target types such as human and vehicle), Event Tracking,Smart Record,ANR (Automatic Network Replenishment), Dual-VCA, ROI Main stream, sub-stream and third stream respectively support eight fixed areas.Protection Level-IP67 Standard. Lightning protection, surge protection and voltage transient protection meets IEC61000-4-2-2/3/4/5/6 Preferred Make- Axis/Pelco/Dahua |
| 316 | SITC of 64 Channel NVR Processor : Dual-core embedded processor,Operating System : Pre-loaded Licensed OS,IP Camera Support: Min 64 Channel or higher,Two way talk : 1 Channel O/P and 1 ChannelI/P,Compression : H.265, H.264, MJPEG4,Video Resolution: Should support up to 8MP IP Camera. Video Recording (Incoming bandwidth) :256 Mbps,Video Display Split : 1/4/8/16/32,Video Loss : Support,Camera Blank : Support,Alarm Input/ Output : Min 16 channel / Min 4 Channel or betterHard Disk : Min 8 SATA ports , Smart Phone : iPhone, iPad, Android, Windows,Phone,Protocol :IPv4/IPv6, HTTP, HTTPS, SSL, TCP/IP,UDP, UPnP, ICMP, IGMP,SNMP,RTSP, RTP, SMTP,NTP, DHCP, DNS, PPPOE, DDNS, FTP, IP Filter,ONVIF Profile S,User Account : 10 Users,Trigger Event : Recording,Alarm, Video Push, Email,FTP,Recording Mode : Manual , Schedule , STOP,Search Mode : Time/Date , Alarm , Motion Detection ,Exact Search(accurate to second), Smart Search,Playback : Play, Stop, Pause, Rewind,Fast Play, Next file, Previous file, Next Camera, Previous Camera, Full Screen, Backup Selection,Backup Mode : USB Device / Internal SATA / NetworkInterface Ports : 2 USB 2.0 , 1 RS485 , 1,RS232, 2 RJ45,Ethernet Ports : 1 RJ-45 port (10/100M/1000M),Power SITC : AC 100V~240V, 50/60Hz,Regulatory : CE, FCC,UL and RoHS; Preferred Make-Dahua/Axis/ Pelco |
| 317 | SITC of 6TB Surveillance Grade Hard Disk for NVR for 30 Days Back up; Make-Seagate/WD |
| 318 | 55" 4kLED Panel,Preffered Make-LG/Samsung |
| 319 | Main LT Panel for Main Building:- Supplying, designing, manufacturing, installation, testing and commissioning of LT Panel of 14 SWG CRCA sheet (2 mm) steel , dust and vermin proof with reinforcement of suitable size iron channel size - 100 mm x 100 mm x 6 mm with proper lifting arrangement effecting proper connection of all incomers and outgoing(IP-43) fully compartmentalizedcubical type, floor mounted , totally enclosed, extendable on both sides, switch board and suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50 kA with front operated construction including separate fabrication arrangement for fixing MCCBs and Bus Coupler. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. -The panel includes 415V, 600A, 3Ph, 50kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Busfor main supply and 300A Al bus bar with earth bus bar for DG supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 4, 6 Sq mm PVC Cu. wire.-All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character:Icu=100% Ics with adjustable S/C and O/L-Provision for inbuilt earth leakage module & provision for inbuilt measuring unit. The panel consisting of the followings 4 pole MCCB 400 A,35 kA with fixed thermal magnetic setting as incomer of JSEB 200 amps, 4 pole Changeover 4 pole MCCB 200 A,35 kA with fixed thermal magnetic setting for DG 4 pole MCCB 125 A,16 kA with fixed thermal magnetic setting for UPS and Fire fighting pump 63 A TPN MCB for power DBs+ lift panel+ spare 40 A TPN MCB for lighting DBs Electronic On timer delay -30 sec 600 amp 415 V heavy duty three phase with neutral busbar chamber 300 amp 415 V heavy duty three phase with neutral busbar chamber Indicator switch Selector switch Voltmeter Ameter C.T. Coil 3 nos CT 600/5VA -5 class one Epoxy resin cast CT 1 Set. Make :- Kappa / Matrix / SG Electricals / EPICAST. 9 nos LED indicatore (RYB) of 220V. 1 Set of 3 nosMake :- ESSEN / L&T - ESBEE / Binay / Teknik 9 nos Fuse base with HRC FuseSet of 3 nos.Make :- Legrand / L&T / Schinder. |
| 320 | HT Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed 11000 volt grade. Make:- Finolex / Polycab / Havells / KEI/RR Kable-3 x 50 Sq mm, 11KV XLPE / PVC Al. Ar. Cable |
| 321 | Supply, installation of 200 kVATRANSFORMER( Level -2 as per IS:1180-2014)-200kVA, 11kV/415VOutdoor Transformer: Supply, installation, testing, fixing and commissioning in correct alignment position, effecting proper connections of continuous ratingEnergy efficient , Level-2, 200 kVA, 11/0.433KV, Off Circuit, oil cooled, copper wound, outdoor Transformer along with civil foundation work as perrequired size & length of MS channels as per the norms of 200 kVATransformer with all accessories as per IS:1180-2014, air filled cable box suitable for 11KV 1 Run, 3 Core 50 Sq mm XLPE Al. Ar. Cable and LV termination box shall have suitable arrangement for 1.1 KV, 2 Run, 3.5 Core, 185 Sq mm XLPE Al. Ar. Cable etc as required. (Make:-GTB/Voltamp/Krilskar) |
| 322 | Chemical Earthing-Supply, erection and commissioning & testingalong with earth cutting, digging earth filling for chemical earthing of the building .Soil Treatment-Earth enhancing soil treatment compound TEREC + having essential chemical ingredients, such as ionic chemicals, dispersion chemicalhydroscopic chemicals to be provide stable low resistance for earth terminal to make it maintenance free for over 15 years. Also provision of masonary enclosure 300mmX300mm withCI cover plate having locking arrangement as earth chamber.Specification:Polution free earthcon compound-25kgs-Electrode-2m long, 17mm dia with 250 micron molecularly bonded with copper coated.-HDPE earth pit cover |
| 323 | Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V,3 phase 50 HZ AC supply with enclosure protection class IP 42. For Terrace Pump |
| 324 | Providing and Fixing Wika Direct Mounting Pressure Gauge Assemble with Gate/Ball Valve -Nominal Size of the Dial-40mm,Measurement Range-0-400,Material of case-Stainless Steel-Gr 304,Material of Dial Plate-Aluminium,Material for Window cover-Transpartent Acrylic,Overall Dimension-500mmX500mmX50mm |
| 325 | Providing and Fixing Air release Valve 150 mm Dia AIR RELEASE VALVE Double Ball Type PN - 10 - Flanges as per BS:4504 PN 10 FF (Drilled) 15 Bar Hyd. 10 Bar Hyd.Pattern / Type-Double Ball Type,Pressure Rating / Class-PN-10,Body-Cast Iron,End Connection-Flanged End,SUB CATEGORY-CI Air Release Valve |
| 326 | Providing and Fixing MS Structure support for piping,Size: 20 X 20 X 3 mm,Thickness: 3 mm,Shape: L Shaped,Usage/Application: Construction,Material: Mild Steel,Structure: T angle |
| 327 | Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end) |
| 328 | Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect. |
| 329 | Providing , fixing Dry Chemical Powder(Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester PowderCoated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects(4 Kg Capacity) |
| 330 | Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity) |
| 331 | Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester PowderCoated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects(5 Kg Capacity) |
| 332 | Providing Supplying & Fixing Director Table (For DFO Cabin)having The main desk of size (L)2800mm X (D)2330mm X (H)770mm shall be made out of 90 mm thick honey comb MDF board including with 0.5mm veneer, veneer portion shall be finished with melamine. Side panel shall be made out of 80 mm thick MDF board and front modesty 25 mm thick MDF board veneer coated with melamine polish. Interchangable Side unit shall be size 1400mm(L) x 400mm(D) x660mm(H) and having a provision of a fixed pedestal of three drawers .Side unit top shall be made out of 20mm MDF board including with 0.5mm thick veneer finished and coating with melamine. The under structure shall be made out of 18mm thick MDF board and coated with melamine. Table shall have one fixed pedestal unit attached table top and side panel. Pedestal sides, front and bottom shall be made out of 18mm thick MDF board. Drawer bottom and backing of the pedestal should be 9mm thick MDF board. Drawers shall be in veneer and coated with melamine finish.all complet with all accessories and bye works as per drawing and spacefication. |
| 333 | Providing Supplying & Fixing of Revolving High Back Leather Chair Size:- (W)673mm X (D)508mm X (H)1270mm, |
| 334 | Supply and installation of Cantilever Frame Premium Leatherette Visitor Chair Size (W)610mm X (D)505mm X (H)990mm. Multipurpose fixed cantiliver chair & armrest .14mm thick, BWR grade plywood (IS:303) is used to make the seat and back. Deep cushioned back and seat confirm to body contours for proper aligment. 5% post consumed recycled content & 30% total recycled content. |
| 335 | Supplying and Placing in place Sofa -Two Seater Modern Chic Chester field design sofa. Sofa size- (L)1450mm X (D)880mm X (H)950mm , sofa seat and back are made up of solid pine wood with hot pressed ply wood and upholstered with leatherette. Sofa molded with polyurethane foam & Silicon with minimum of 32 density and back plywood shall be designed with contoured lumbar support for extra comfort. The sofa shall have a wooden framed design running through the sides of the arm rests and wooden legs. |
| 336 | SOLID WOOD SIDE TABLE Pair your Sofas with the Basil Side table, a stylish new addition to our catalog of living room furniture. Made from toughened glass and wood, this table is an ideal pairing with any sofa. Place a table lamp for reading or keep your magazines and papers handy with this table by your sofa. Product Dimension : (L) 450mm X (D) 450mm X (H) 485mm Variation : Side & End Tables. |
| 337 | Providing Supplying & Fixing of The Hopper centre table is made keeping your comfort in mind. The sheen on the glass table top will ensure you are the envy of many a neighbour. In laid onto a solid wood frame that slopes inward, the table is a gorgeous piece of furniture to highlight your living room. The turned wooden legs are sleek and sturdy providing the table with its support. The wood work below the glass provides the glass with a focal point and some support. Add volumes of style to your living room with the Hopper centre table.Dimension(L)1130mm X (W)630mm X (H)410mm. |
| 338 | Providing Supplying & Fixing DFO OFFICE Table, Table with side unit return- Table Size(1500x750x750)mm & Side runner Size(900x400x750)mm. Table made of 25mm thk pre lam particle board with edge banding. Table top supported with side panel & fron panel. Kyeboard tray & cpu trolly. Table top with wire manager & interchangable side runner with fixed pedestalof 3 drawers. Phenol bond using in Pre-Laminated Particle Board & Edge band thickness will be start from 2mm for Top & 1mm for rest parts. Our PLPB certified from ISI grade & Termite, Borer & Fungus resistance laminated outside in selected color & inside (Non Visible Part) will be balancing white. 100% European design & texture & 100% Product Consistency, fade resistance lamination best International Technology. |
| 339 | Providing Supplying & Fixing The seat shall be made up of 1.2+/- 0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded polyurethane foam shall be ofdensity 40+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 59.0cm(W) x 50.5cm(D) and of back shall be 59.0cm(W) x 71.0Cm(H). Chrome plated base with gas height adjustment and central tilting with single locking machenaism. Armrest with padding. Leatherette uphlostery has the look and feel of top grain leather. Cushion with lumber support for all day comfort. The mechanism of the chair shall have following features : 360° revolving type, Center Tilt mechanism, Tilt tension adjustment, Single point control. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestial shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap. with castors). The twin wheel castorsshall be made black nylon. |
| 340 | Supply and installation of Visitor Chair Size (W-590 X D-490 X H- 980 ). Multipurpose fixed cantiliver chair & armrest .14mm thick, BWR grade plywood (IS:303) is used to make the seat and back. Deep cushioned back and seat confirm to body contours for proper aligment. 5% post consumed recycled content & 30% total recycled content. Color-Black. |
| 341 | Providing Supplying & Fixing Secretary Table, Table with side unit return- Table Size(1500x600x750)mm & Side runner Size(900x400x750)mm. Table made of 25mm thk pre lam particle board with edge banding. Table top supported with side panel & fron panel. Kyeboard tray & cpu trolly. Locable side runner with sliding shutter & shelf. Color-Maple & Dark Gray. |
| 342 | Supply and installationRevolving Chair Overall height 914mm max, 1065mm min, seat size 475mm (W) x 485mm(D) and back size 470mm (W) x 495mm(H), seat and back are made up of 12-15mm thick hot pressed ply wood upholstered with fabric in front and back ,High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 40 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression.) molded with polyurethane foam. The chair shall havepush back mechanism with 17 degree max. tilt and full 360 degrees swivel mechanism. The prong (base) is made of nylon and fitted with 5nos. twin wheel castors (castor wheel dia. 50mm). The prong (base) is 620mm pitch center dia (660mm with castors). The telescopic bellows is 3 piece telescopic type and injection molded in black polyurethane. |
| 343 | Providing Supplying & FixingVisitor Chair ,The modern design is perfect for cafeteria seating or lounge seating. The block panelled back and waterfall seat cushions make this chair a classy addition to the workspace. An all metal construction powder coated, gives it a solid look. The arms are padded for comfort. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 40 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression.) Product Dimension : (W)595mm X (D)510mm X (H)875mm, |
| 344 | Supply and installation 3 SEATER METAL PERFORATED CHAIR. Length 1775mmx Depth 690mm x Height 755mm1)Seat & back single section 2)Seat is 410 mm from ground 3)Perforated mild steel powder coated 4)Seat thickness 1.2 mm 5)Seat width 520 mm 6)Beam MILD steel with black power coating thickness 1.6mm 7) Mild steel border with chrome plating for every seat & back 8) Mild steel handles chrome plated & die pressed legs at the end of chairs 9) Gross weight of regular 3-seater will be 31 kg. |
| 345 | Supply and installation 3L PERFORATED CHAIR. Seat & back single section 2)Seat is 410 mm from ground 3)Perforated mild steel powder coated 4)Seat thickness 1.2 mm 5)Seat width 520 mm 6)Beam MILD steel with black power coating thickness 1.6mm 7) Mild steel border with chrome plating for every seat & back 8) Mild steel handles chrome plated & die pressed legs at the end of chairs 9) Gross weight of regular 2-seater will be 21 kg. |
| 346 | Providing Supplying & Fixing Conference Table 10 Seater TOP MADE OF 25MM THK. PRELAM PARTICLE BOARD TABLETOP WITH PVC EDGE BANDING. MODEL NO DWS/34762 (CP-01 no., SP1-04 Nos and SP2-01 No.) CP Size-(L)1200mm X (D)600mm X (H)750mm, SP-1 Size:-(L)1350mm X (D)600mm X (H)750mm, SP-2 Size:-(L)750mm X (D)600mm X (H)750mm. |
| 347 | Providing Supplying & Fixing Conferance cum Staff Chair The seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded polyurethane foam shall be of density 40+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- (W)660mm X (D)505mm X (H)1105mm. Chrome plated base with gas height adjustment and central tilting with single locking machenaism. Armrest with padding. Leatherette uphlostery has the look and feel of top grain leather. Cushion with lumber support for all day comfort. The mechanism of the chair shall have following features : 360° revolving type, Center Tilt mechanism, Tilt tension adjustment, Single point control. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestial shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap. with castors). The twin wheel castors shall be made black nylon. |
| 348 | Providing and placing in position Premium Leatherette Training chair moulded in Premium Leatherette upholestry on seat and MS + Chrome with desklet armsrest. |
| 349 | Providing Supplying & Fixing Conference Table 20 Seater TOP MADE OF25MM THK. PRELAM PARTICLE BOARD TABLETOP WITH PVC EDGE BANDING. Size-L-7600mm X 1200mm X 750mm. |
| 350 | Workstation - 65 Series Size : 1200L X 600D X 1200Ht 67mm thk Sliding Tile Base partition of 1200mm heightin main and side Span.Sliding tile base partition made out of CRCA 1.2mm thk Vertical section and Top / Bottom connectore are made of 1mm thk with cut-out for through and through wiring from floor to partition.2mm thk Aluminum trims are elegantly fixed in partition with special fixtures, for final finishes. All frames / trims are powder coated with 50 micron. The frame work shall be fitted with 9mm thick tiles of approved shade. Partition shall have provision of tile combination options as below:- Pin up boardwith fabric, White marker, Prelaminated Particle board / Prelaminated MDF board, Metal tile with powder coating finishof 50 micron.Partition framework shall have adequate provisions for the movement of electric data cables at desired 2 levels:- one at skirting and another above / below the table top. With cut-out provision for switches / sockets.Tabletop for workstation is made up of 25mm thick Pre laminated Particle board of approved shade. All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue.Gable ends of 18mm thk. Prelam Particle board at 2 ends (near window).Provision of Mobile Pedestal of Size: 400L X 450W X 600Ht, Pedestal made of 18mm thk Prelam Particle board with PVC Edge banding.Provision of PVC Keyboard tray & CPU Trolley with castors. |
| 351 | Providing Supplying & Fixing of Carribean Dining table 8 STR. The Carribean table is perfect for casual dining at homes on acoount of its simple classic lines. Made of engineered wood polished to a fine shine its rectangular form can seat 4 people comfortably. The table top is laminated with exotic Veneer that has a matte rosewood finish. The Carribeans Legs are made up of high quality solid wood known for its resilience and rigidity. Pair this up with any of the chairs we have in the collection for a truly customisable dining set thats yours and enjoy all your meals in comfort,(L)1150mm X (W)750mm X (H)760mm. |
| 352 | SUKRANTI- MR-C/ 6 PASSENGER LIFT/ 544 Kgs / 4 Floors / 4 Stops / STAINLESS STEEL Car Cabin-LIFT SPECIFICATION -Number Of Lifts/Type Of Lift:ONE / SUKRANTI- MR-C - PASSENGER,Load / Speed:6 Persons (408Kgs.) / 1.25 Mtr. Per Second,Drive:MICRO PROCESSOR BASED VVVF,Travel / PIT / HEADROOM:12 METER / PIT 1600mm / HEADROOM 4200 mm,Number Of Floors:4 (G+3),Floor Display Char:0,1,2,3,Number Of Landing Entrances:4 (G+3),Number and Position of Car Entrances:1 (ONE), IN FRONT ONLY,Position Of Machinery:MACHINE ROOMLESS - GEARLESS,Size of Lift Well:1650 X 1475 (MM Wide * MM Depth * MM Height * MM E-Value),Lift Car Inside Size:1000 X 1100 X 2200 (MM Wide * MM Depth * MM Height * MM C-Value),Clear opening of Gates / Doors / Lintel / Ec:700 X 2000 (MM Wide * MM Height) Lintel - 2200 mm,Type or Design of Lift Car:STAINLESS STEEL - MOONROCK,Car Ceiling - Car Floor,SLEEK MEDIUM CIRCULAR-JLFC 05 - SS HAIRLINE FINISH -20 MM RECCESS,Car Fittings:JLPL135 & REGULAR (CIRCULAR) - FAN,Type Of Car Front Entrance Protection:POWER OPERATED CENTRE OPENING SLIDING DOOR WITH VISION PANEL - STAINLESS STEEL - MOONROCK,Land Entrance Protection (0,1,2,3 ):CENTRE OPENING DOOR WITH VISION PANEL - STAINLESS STEEL - MOONROCK,Landing Door Frame (0,1,2,3 ):STAINLESS STEEL - MOONROCK,Type Of Control System:MICROPROCESSOR BASED SIMPLEX SELECTIVE COLLECTIVE CONTROL WITH / WITHOUT ATTENDENT,Electric Supply:AC 3 PHASE, 50 CYCLES, 415 VOLTS ±10%,Delivery Period / Time Of Erection:2MONTHS / EX-WORKS / 2 MONTHS,Car Operating Panel Model:CAR OPERATING PANEL - JLCP01,Landing Operating Panel Model:LANDING OPERATING PANEL - JLPL (JSM322) / JLLP05,Landing Operating Panel Mounting Type:SURFACE/WALL MOUNTABLE,Special Inclusions:REFER ANNEXURE,Car Display:ORANGE SQUARE DOT-MATRIX SCHROLLING DISPLAY-VERTICAL,Floor Display 0,3,2,1:ORANGE SQUARE DOT-MATRIX SCHROLLING DISPLAY-VERTICAL |
| 353 | Add 18 % GST |
| 354 | Add 1% Labour Cess |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
