Department Of Building And Construction-DOBAC has published Tender For Establishing Mizo Cultural Heritage Centre For Protecting The Historical And Natural Heritage Of Mizo At Kawlri, Serchhip District. Submission Date for this Tender is 22-01-2024. Building Work Tenders in Serchhip Mizoram. Bidders can get complete Tender details and download the document.
Sl. No. | Item Description |
1 | Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. (b) Ordinary Rock. |
2 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50 metres outside the periphery of the area cleared. (a) By manual means. (iii) Heavy Jungle. |
3 | Surface dressing of ground including removing vegetation and inequalities not exceeding 15cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5m . (a) All kinds of soil. |
4 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: (a)All kinds of soil. |
5 | Earthwork in excavation over areas (exceeding 30cm in depth,1.5m in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. (a) Ordinary and Hard Soil. |
6 | Earthwork in excavation in foundation trenches or drains etc. (not exceeding 1.5m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m including getting out excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres. (b) Hard Soil( pick work ) |
7 | Earthwork in excavation in foundation trenches or drains etc. (not exceeding 1.5m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m including getting out excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres. (c) Very Hard Soil( jumper work ) |
8 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
9 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. (b) Oridinary Rock |
10 | Providing and laying in position cement concrete of specified grade excludingcost of centering and shuttering - All work upto plinth level: (a) 1:3:6 (1 cement : 3 coarse sand : 6 stone aggregate 20mm nominal size) |
11 | Providing and laying in position reinforced cement concreteexcluding cost of centering and shuttering , finishing and reinforcement in - All work upto plinth level : (a)1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate20mm nominal size). |
12 | Providing and laying in position reinforced cement concreteexcluding cost of centering and shuttering , finishing and reinforcement in - All work upto plinth level: (b) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate20mm nominal size) |
13 | Reinforced cement concrete work in walls including attached pillasters, columns, pillers, posts, piers, abutments, return walls, retaining walls,struts, buttresses, string or lacing courses, fillets etc. upto floor five level excluding cost of centering shuttering etc complete. (b)1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate20mm nominal size) |
14 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement complete. (b) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate20mm nominal size) |
15 | Extra for providing and mixing water proofing material in plain and reinforced cement concrete work in the proportion recommended by the manufacturers. |
16 | Centering and shuttering including strutting,propping etd. And removal of form for all heights: (d) Lintels, beams, plinth beams, girders, bressumers and cantilevers, etc. |
17 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : (a) Foundations, footings, bases of columns etc. for mass concrete. |
18 | (b) Walls including attached pillasters, buttresses, string courses, etc. |
19 | (c) Columns, pillars, piers, abutments, posts and struts. |
20 | (d) Lintels, beams, plinth beams, girders, bressumers and cantilevers, etc. |
21 | (e) Suspended floors, roofs, landings, shelves and their support, balconies and chajjaj,etc. |
22 | (f) Staircases (except spiral staircase) excluding landings. |
23 | Steel reinforcement for RCC work including straigh- thening, cutting, bending, placing in position and binding all complete. |
24 | Steel reinforcement for RCC work including straighthening, cutting, bending, placing in position and binding all complete. (a) Mild steel and Medium Tensile steel bars. |
25 | Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. “(Note:- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately) (a) All works upto plinth level. |
26 | (b) All work from plinth level upto floor V level. |
27 | Extra for providing richer or leaner mixes respectively at all floor levels . (b) Providing M-30 grade concrete instead of M-20 grade BMC/ RMC. (Note : Cement content considered in M-30 is @ 340 kg/ cum). |
28 | First class brickworkin foundation and plinth in : (b) in cement mortar 1: 4 ( 1 cement : 4 coarse sand ) |
29 | Half brick masonry with first class brickin foundationand plinth in: (a) in cement moratar 1:3 (1 cement : 3 coarse sand ) |
30 | Honey-comb half brick masonry withfirst class brickin foundation upto one storey above and below ground level including curing, etc. complete. (b) in cement mortar 1:4 (1 cement : 4 coarse sand) |
31 | Honey-comb half brick masonry withfirst class brickin foundation upto one storey above and below ground level including curing, etc. complete. (a) in cement mortar 1:3 ( 1 cement : 3 coarse sand ) |
32 | 7.5 cm thick brick masonry with first class brickin superstructure above plinth level upto floor two level including curing, etc. complete . (b) in cement mortar 1:4 (1 cement : 4 coarse sand) |
33 | Coursed rubble masonry(second sort) with hard stone in sperstructure aboveplinth level and upto floor five level with (c) cement mortar 1 : 6 ( 1cement :6 coarse sand). |
34 | Providing 2nd class local wood work dressed in frames of sill, upright, batten, post, beams, etc. as structural members fixed in position complete. |
35 | Providing Ist class local wood dressed in frames of chaukat for doors, windows, clerestory windows fixed in position. |
36 | Providing 1st class local wood in trusses etc. including hoisting fixing in position supplying necessary fittings such as spikes bolts and nuts, nails etc and applying wood preservative for unexposed surface etc. complete. |
37 | Providing and fixing 20mm thick 2nd class local wood battened and braced shutters for doors and windows with necessary ledges and braces 25mm thick including bright finished or/and black enamelled M.ST-hinges at ledges with necessary screws. |
38 | Providing and fixing 40mm thick panelled door shutter comprising of styles and rails of seasoned teak wood with panels of Duratuffboard 25mm thick as per required architectural designincluding M.S. butt hinges with necessary screws but excluding varnishing/painting etc. |
39 | Supplying, fitting and fixing decorative wood railing 80cm high in staircase etc. including dressing wood in round 16cm to 20cm circumference and fixed wooden wedge dressing wood for wedge etc. complete. (b) Using 1st class local wood. |
40 | Factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of "H" section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. "U" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer"s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter) (Sintex, Plasopan or equivalent). (b)30mm thick shutter. |
41 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
42 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
43 | Supplying and fixing M.S. decorative railing consisting of top and bottom rails of 40mmx40mm square or circular section at distance of 788mm apart, 30mmx30mm square or circular section decorative intermediate balusters welded to top and bottom rails at 280mm apart. The base of balusters at 560mm apart welded with base plate of 60mmx3mm thick and fixed with cement grouting firmly to concrete section including steel priming ans steel painting complete etc. |
44 | Supplying of glass panes at site. (b) 5mm thick plate sheet glass. |
45 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS: 733 and IS : 1285, anodised transparent or dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately ). For fixed portion. (c) Powder coated. |
46 | Providing andlaying ceramic glazedfloor tiles of size 300x300mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS: 15622 of approved make in all colours,shades, except white,ivory,grey,fume red brown, laid on 20mm thickcement mortar 1 : 4 (1 cement : 4 course sand)including pointing the joints with white cement and matching pigments etc. complete. as per designed colour. (b) Matt/Antiscratch. |
47 | Providing andceramic glazedfloor tiles of size 300x300mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS: 15622 of approved make in all colours,shades, except white,ivory,grey,fume red brown, laid on 20mm thickcement mortar 1 : 4 (1cement : 4 course sand)including pointing the joints with white cement and matching pigments etc. complete. as per designed colour. (C) Parking Tiles. |
48 | Providing & laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS:15622,of approved make, in all colours and shades, laid on bed of 20mm thick cement mortar 1 : 4 (1cement:4course sand),including the joints withwhite cement and matching pigments etc.complete.as per design collours. (a) Full body polish vitrified (General) |
49 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacaturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12mm thick bed of cemunt mortar 1:3 (1 cement : 3 coarse sand) and jointing with cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
50 | Providing 40 x 5mm flat iron hold fast 40 cm long including fixing to frame with 10mm dia. bolts, nuts and wooden plugs and embeddings in cement concrete block 30 x 10 x 15cm 1:3:6 mix (1 cement : 3 sand : 6 well graded stone aggregate 20 mm nominal size) |
51 | Providing and fixing CP Brass Sliding Door Bolts (aldrops) bright finished with nuts and screws etc. complete. (a) 300 x 16 mm. |
52 | Providing and fixing CP brass tower bolts (socket bolts) bright finished with necessary screws etc. complete. (a) 250 mm. |
53 | (c) 150 mm. |
54 | Providing and fixing CP brass handles with necessary screws, etc. complete (a) 250 mm. |
55 | Providing and fixing CP brass handles with necessary screws, etc. complete (b) 200 mm. |
56 | Providing and fixing bright finished CP brass two lever mortise door lock with necessary screws, etc. complete. (a) Union Type. |
57 | Providing and fixing aluminium frame works for ceiling lining consisting of battens 50x25mm fixed over plugs embedded in wall with necessary nails or screws, etc. complete. |
58 | Providing and fixing false ceiling with 12 mm thick plain/or with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to IS:3087 finished with a coat of aluminium primer on both sides & edges and two coats of synthetic enamel paint of approved quality on exposed face fixed to a grid made out of anodised aluminium (with 15 micron anodic coating) T-sections 35 x15x1.5 mm size main runners and cross runners 23.5x19x1.5 mm fixed to main runners placed 600 mm centre to centre both ways so as to form a grid of 600 mm square. The frame work shall be suspended from ceiling by level adjusting hangers of 6 mm dia M.S rod fixed to roof slab by means of ceiling cleats. The suspenders shall be placed 600x 1200 mm centre to centre including fixing to the frame with C.P brace screws and applying a priming coat of zinc chromate yellow primer : |
59 | Providing Trapezoidal Polyester Coated Galvanised Steel Sheets Roofing of any colourof 1.06m width at all levels including fitting and fixing ridging with self drilling , self tapping screws, EPDM washers etc. complete excluding the cost of purlin, rafter and trusses. (ii) For 0.50 mm thick |
60 | Providing and fixing of Polyester Coated Galvanised Steel Sheets of any colourridges, gutters or valleys 50cm overallwidth 0.50mm thick with 150 mm overlapping fixed with Self Drilling & Tapping Screws with EPDM washer but excluding the cost of base frame. (ii) For0.50 mmthick. |
61 | Providing and fixing low level P.V.C. flushing cistern of Parryware/Hindware/Cera and equivalent make with fittings complete. (ii)10 litres-Pastel. |
62 | Providing and fixing vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : (ii) Pastel. |
63 | Providing and fixing White vitreous china wash basin Standard of Parryware/ Hindware/ Cera and equivalent make with R.S. or C.I. brackets, 15mm C.P. brass pillar taps, C.P. brass chain with rubber plugs, 32mm C.P. brass waste of standard pattern, 32mm C.P. brass traps and union complete including painting of fittings and brackets, cutting and making good the walls wherever required. (a) Vitreous China Wash basin size 630x450 mm with single 15 mm C.P. brass pillar taps. |
64 | Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick asbestos sheet ground fixed to cleats with C.P. brass screws and washers. |
65 | Providing and fixing C.P. brass towel rail with two C.P. brass brackets to wooden cleats with C.P. brass screws. (a) 750 x 20 mm size. |
66 | Providing and fixing toilet paper holder. (a) C.P. brass toilet paper holder of standard size. |
67 | Providing and fixing soap dish fixedwith C.P. brass screws. |
68 | Providing and fixing on wall face SWRPVC soil, waste and vent pipes including jointing with rubber lubricant/cement solvent complete. (a) 110 mm dia. |
69 | (b) 75 mm dia. |
70 | Providing and fixing SWRPVC plain bend of required degree ( 87.50° ) including jointing with rubber lubricant/cement solvent complete. (a) 110 mm dia. |
71 | (b) 75 mm dia. |
72 | Providing and fixing SWRPVC plain bend of required degree (45°) including jointing with rubber lubricant/cement solvent complete. (a) 110 mm dia. |
73 | (b) 75 mm dia. |
74 | Providing and fixing single equal SWRPVC plain junction of required degree (T-junction) . (b) 75 x 75 x 75 mm. |
75 | Providing and fixing single equal SWRPVC plain junction of required degree (T-junction) . (a) 110 x 110 x 110 mm. |
76 | Providing and fixing SWRPVC socket including jointing with rubber lubricant/cement solvent. (a) 110 mm dia socket. |
77 | (b) 75 mm dia socket. |
78 | Providing and fixing ventilation cowl including jointing with rubber lubricant/cement solvent complete. (a) 110mm SWRPVC vent cowl. |
79 | Providing and fixing W.C. connection bend type (siphon) (SWRPVC) including jointing with rubber lubricant/ solvent cement. |
80 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (a) Sintex or quivalent |
81 | Providing and fixing G.I. pipes complete with G.I. fitting and clamps, including cutting and making good the walls etc. (internal works- exposed on wall). (b) 25mm dia nominal bore. |
82 | Providing and fixing G.I. pipes complete with G.I. fitting and clamps, including cutting and making good the walls etc. (internal works- exposed on wall). (a) 20 mm dia nominal bore. |
83 | Extra for concealed in brick and RCC works by making chases upto 7.5x7.5cm in walls and making good the same after housing pipes, etc. |
84 | Providing and fixing G.I. pipe complete with G.I. fitting including trenching and refilling etc. (external work). (c) 25mm dia nominal bore. |
85 | (e) 40mm dia nominal bore. |
86 | Providing and fixing brass bib cock of approved quality. (c) 25 mm nominal bore. |
87 | Providing and fixing brass bib cock of approved quality. (b) 20 mm nominal bore. |
88 | Providing and fixing brass stop cock of approved quality. (c) 25 mm nominal bore. |
89 | Providing and fixing brass stop cock of approved quality. (b) 20 mm nominal bore. |
90 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) . (c) 25 mm nominal bore. |
91 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) . (b) 20 mm nominal bore. |
92 | (e) 40 mm nominal bore. |
93 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : (c) 25 mm nominal bore. |
94 | Providing and fixing 15 mm nominal bore C.P. brass angle stop cock for basin mixer and geyser points of approved quality conforming to IS:8931 . (c) Class-I. |
95 | Providing and fixing chromium plated brass shower rose with 15 or 20mm inlet. (b) 150 mm dia CP brass shower rose. |
96 | Providing and placing in position electric water pump of approved manufacture including connections to G.I pipes etc. complete with accessories. (b) 750 watts. |
97 | 12mm cement plaster 1 : 6 (1 cement :6 fine sand). |
98 | 12mm cement plaster 1 : 3 (1 cement : 3 fine sand). |
99 | 12mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
100 | 12mm cement plaster 1 : 6 (1 cement :6 fine sand). |
101 | 12mm cement plaster 1 : 3 (1 cement : 3 fine sand) finished with a floating coat of neat cement. |
102 | 12mm cement plaster 1 : 4 (1 cement : 4 fine sand) finished with a floating coat of neat cement. |
103 | 20mm cement plaster 1 : 3 (1 cement : 3 fine sand) finished with a floating coat of neat cement. |
104 | 6mm cement plaster to ceiling 1 : 3 (1 cement : 3 fine sand) |
105 | 6mm cement plaster to ceiling 1 : 4 (1 cement : 4 fine sand) |
106 | Extra for providing and mixing water proofing materials in proportion recommended by manufacture in - (b) 12mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
107 | Extra for providing and mixing water proofing materials in proportion recommended by manufacture in - (a) 12mm cement plaster 1 : 3 (1 cement : 3 fine sand). |
108 | (e) 20mm cement plaster 1:3 (1 cement :3 sand). |
109 | Applying priming coat with ready mixed primer of approved brand and manufacture on plaster surface. (a) Ready mix white primer. |
110 | Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) & Plywood. |
111 | Finishing walls with high performance elastomeric decorative exterior water proofing coating of approved brand and of required shade on new work. |
112 | Painting with synthetic enamel paint of approved brand and manufacture in all shades on new work (two or more coats). (b) High gloss. |
113 | Wall painting with water and weather proof paint (Latex Emulsion base) on cement works of approved brand and manufacture (ISI/ISO certified) of required shade on new work (two or more coats) to give an even shade . |
114 | Finishing walls withexterior emulsion of required shade on new work (three or more coats) to give an even shade. (c) Regular exterior emulsion like supercote, walmasta etc. |
115 | 1.8m high G.I. barbed wire fencing with 2.4m angle iron posts 50 x 50 x 6mm size placed 2.0m apart embedded in cement concrete block 1:3:6 (1 cement : 3 sand : 6 stone aggegate) of size 25 x 25 x 60 cm and using 12 horizontal lines and 2 diagonals barbed wire fixed from post to post with "U" nails and projecting the angle post 2cm above the top most wire including earthwork complete. |
116 | Providing and fixing Zinc galvanised iron wire mesh. |
117 | Carriages by Mechanical Transport. Quantity taken from Item No. 1/2.18 Disposal of surplus excavated earth upto 5 km |
118 | Carriages by Mechanical Transport. Disposal of surplus excavated earth upto 5 km |
119 | Carriages by Mechanical Transport. Disposal of surplus excavated earth upto 5 km |
120 | E:01:00 LIGHTING AND POWER WIRINGS Wiring in looping system with PVC wire sheathedstandard copper conductor/wires as perIS:694(1990) and Flame retardant low smoke & Halogen (FR-LSH)1100 voltage graded copper flexiblewire stranded copper running inside PVC casing & capping (Gr-II) of different sizes fixed, surface on thewall/ceiling/floor as per convenience including junction box having required numbers of ways fromcontrol switch to the light point etc as required: A. TO A LIGHT POINT : (B) Short point |
121 | (C) Medium point |
122 | (D) Long point |
123 | (b) Two points controlled by one switch |
124 | B. TO A WALL FAN POINT: (C) Medium point |
125 | Wiring in looping system with PVC wire sheathedstandard copper conductor/wires as per IS:694(1990) and Flame retardant low smoke & Halogen (FR-LSH)1100 voltage graded copper flexiblewire stranded copper running inside PVC casing & capping (Gr-II) 25x12mm fixed, surface on the wall/ceiling/floor as per convinience including junction box having required numbers of ways fromDB to the power plug/socket 15/16A point etc. as required :- (D) Long point |
126 | Wiring in parallel system with PVC wire sheathedstandard copper conductor/wires as perIS:694(1990) and Flame retardant low smoke & Halogen (FR-LSH)1100 voltage graded copper flexible wire stranded copper running inside PVC Casing & capping (Gr-II) 20x12/25x12/32x12/3840X15/20mm dia" fixed,surface onthe wall/ceiling/floor as per convenience including junction boxhaving required numbers of ways from Main to Sub-Main/DB/Sub-Main/DB to SDB/SDB/Switchboards/SDB to switch boards as required:- (A) 2X2.5 sq.mm |
127 | (B) 2X4sqmm |
128 | (C) 2X6sqmm |
129 | Wiring in parallel system with PVC wire sheathedstandard copper conductor/wires as perIS:694(1990) and Flame retardant low smoke & Halogen (FR-LSH)1100 voltage graded copperflexible wire stranded copper running inside PVC Casing & capping (Gr-II)25/30/38mmx15mm dia" fixed,surface onthe wall/ceiling/floor as per convenience including junction box having requirednumbers of ways from Main to Sub-Main/DB/Sub-Main/DB to SDB/SDB/Switch boards/SDB toswitch boards as required:- (C) 4X6sqmm |
130 | (D) 4X10sqmm |
131 | E:02:00LIGHTING FIXTURES AND FANS Supplying of all types ofCFL/FL Ceiling mounted mirror optics/fibre cover/industrialtype surface type with electronic ballast/ballast, condenser /electronic filter etc.in complete as follows:- a) Recess Mounting luminaires 2X36W FP-L HF MIRROR OPTICS AS SERIESmirror optic luminaire with electronic ballast suitable for AS/GB/POP ceiling. (Havells/ Phillps/Gromton/Bajaj) |
132 | b) Surface mounting luminaires 2 X 36W FP-L HF MIRROR OPTICS P5 (SURFACE)mirror optics luminaire with P5 Paralite louvre(Havells/ Phillps/Gromton/Bajaj) |
133 | c) Recess Mounting luminaires 2X18W FP-L HF MIRROR OPTIC - CABIN LITE P5 RECESSmirror optic luminaire with P5 paralite louvre for CFL/FP-L.(Havells/ Phillps/Gromton/Bajaj) |
134 | Supplying of all types of CFL and FL types FC tube in complete as follows:- CFL Curvy15W (SP)B22,E27 Base Havells/Equivalent |
135 | Supplying,fitting and fixingangleHolder including connection etc, as required |
136 | Installation, testing & commissioning of pre-wired flourescent Light fittings of all types, with allaccessories and tubes etc, directly on ceiling/wall, including supplying and fixing of ball and socketarrangement,2 Nos" down rod of 20mm diameter X 1.6 mm thick steel conduit pipe upto 30 cm length,painting and wiring the down rod and connection with 1.5 sqmm PVC insulated copper conductor single core cable etc, as required. |
137 | Supplying of pre-wired wall fanas per IS:374 (1979) in a set includ-ing socket type, canopy, AC wall fan machines,socket etc. in completedas folows:- Bracket wall mounting fan 400mm sweeps Mist air Ultra/Stiker High speedISI marked |
138 | Installation, testing & commissioning of ceiling fan and regulator, including wiring the downrod of standard length (upto 30cm) with 2X1.5 sqmm PVC insulated copper conductor single core cable etc, as required. |
139 | E:03:00: LOAD LINE,MAIN DISTRIBUTION BOARDS,SWITCH BOARD ETC. SWITCH BOARD AND SWITCHES Supplying and fixing of Modular switch board of the following sizes/modules on surface/recess including PVC/Steel boxes,modular plate and necessary switches,plug/socket, and fan regulators etc. with necessary painting if necessary A. ONE MODULE (1) 1 S |
140 | B. TWO MODULES (13) 2 S |
141 | Supplying and fixing of all types and ratings MCB’s RCCB’s etc 240/414V,50hz AC supply in the existing MCB DB complete with connection, testing and commissioning etc in complete. (1)5-32A SP MCB L/G Series |
142 | Supplying and fixing of different waysManiature Circuit breaker(MCB) Distribution board(DB) single phase SP & N/Three Phase TP&N economy type with sheet metal,Acrylic cover Phosphatised powder painted, Bus Bar, Neutral link, earth bar anf din rail conforms toIS:13032 .IS:8623, BS:5486 240/415 volts, 50 Hz, AC supply on recess/surface including inter-connection,painting etc. in completed. (20) 8 ways (8+24)MCB DB TP&N D/D |
143 | LOAD LINE DISTRIBUTION BOARDS WITH MCCBs( out-going with MCBs) 6)12-ways MCB DB TP&N Loadline duobleDoor vertical suitable for G-frame MCCB (without MCCB) |
144 | E:04:00EARTHING E:04:00EARTHING AND LIGHTNING ARRESTOR 51) Providing and fixing of 8 SWG Copper Wire on surface or in recess for loop earthing alongwith the existing surface/recess conduit/sub-main wiring/cables etc.as required. |
145 | 55) Supplying and drawing of 1.5 sqmm PVC sheathed copper conductor for loop earthing in the existing surface/recess steel/PVC conduit/PVC cassing & capping/wood batten alongwith others wires as required. |
146 | 13) Advance maintenance free earthing of different dia,length and wall thicknesscopper/Galvanized bondelectrode provding masonery enclosure withcover plate having locking arrangment and waterpipe, etc. ( but without charcoal or coke and salt ) complete as required.(a) Advance maintenance free earthing 48mm 2 meter length 3.2mm wall thickness copper bond with 2 bags back filling compoundelectrode (b) 40mm dia G.I pipe medium class-3mtrs (c) Funnel G.I nuts & through bolts, washer- set-1 (c) Locking arrangement,with hings cover plate No-1 |
147 | LIGHTNING ARRESTOR (04) Providing & fixing of lightning conductor finial, made of copper five finger system with 85mm diameter 3mm thick base plate including holes etc completed. |
148 | (59)Providing & fixing of copper tape 20mmx3mm thick on parapet or surface of wallfor lightning conductor as required ( for vertical run ) |
149 | (60)Providing & fixing of copper tape 20mmx3mmthick on parapet or surface of wallfor lightning conductor as required ( for horizontal run ) |
150 | (61)Rivetting,sweating and soldering of copper/G.I tape ( with another copper/ G.I Tape base of the finial r any other metallic object ) as required |
151 | (65)Providing & fixing of testing joint made of 20mmx3mm thick copper strip 125mm long with 4 Nos of Tinned brass bolts,nuts,check nuts and spring washer etc.complete as required |
152 | External Service Connection for Building (LS) |
153 | CONTINGENCIES |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail