|
| 1 | Excavating in trenches n. exc 1.5 m width and n. exc 1.5 m in depth for foundation or etc or for shafts , wells , cesspits , manholes , pier holes etc n exc 10 sqm on plan and n exc 1.5 m in depth orgetting out in any type ofsoil,complete all as specified and as directed. |
| 2 | M & L cement concrete in foundation, filling and mass concrete type D-2, 1:4:8 mix using 40 mm graded stone aggregate, completed all as specified and directed. |
| 3 | M&L for pre-cast cement concrete block masonry of type C1 1:3:6 (using 20mm graded stone aggregate) with solid blocks exc 10cm in width and setting in cement mortar 1:4etc complete all as specified and as directed. |
| 4 | Returning,filling in including spreading ,levelling,watering and well ramming in layers not exc 25 cm |
| 5 | Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed |
| 6 | M&L for RCC TypeB1 1:2:4(using 20 mm graded aggregate) as in Beams/bands cantilevers, bressummers, lintels over 1.5m span |
| 7 | M&L for mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90 mm dia complete all as specified and as directed. |
| 8 | M&L for mild steel TMT bars 6 to 8 mm dia and over, cut to length bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90 mm dia complete all as specified and as directed. |
| 9 | M& L for form works to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including support , overhangs etc. for rough finished surfaces complete all as specified and directed. |
| 10 | M & L Cement concrete type B-0 1:2:4 (12.5mm grades aggregate) in coping concrete etc complete all as specified and as directed |
| 11 | M&L for plastering inexternal wall surfaces of 15mm thick in CM 1:4on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed by Engr -in- charge. |
| 12 | M&L for preparation of newly plastered surfaces of external walls and applying two coats cement base paint over a coat ofcement primer complete all as specified and directed by the Engineer-in-Charge. |
| 13 | M&L providing precast cement concrete jallies, 25mm thick type B0 1:2:4 (12.5mm graded aggregate) and set in CM 1:6, (measured solid), including all mouldings all as specified. |
| 14 | M&L for framed work such as grills gratings etc with ends of bars shoulderd and /or rivetted,or forged into spikes framed guardbars barred iron doors ladders framed balusters walk ways railing framework of water tanks and similkar work conforming to FE 290 Gde-E-165 |
| 15 | M&L preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide/zinc chrome primer complete all as specified and as directed. |
| 16 | Dismantling existing barbed wire/plain wire/ chain linkfencing any type from RCC/Steel/Wdn posts complete etc all as specified and as directed. |
| 17 | Dismantling posts or struts(wood ,steel or RCC) of any section including taking out embedded portion and making good disturbed ground all as specified and directed. |
| 18 | Demolition of Brick/stone masonry built in cement mortar of any description, etc complete all as specified and as directed |
| 19 | Demolition ofplain cement concrete of any description and in any position not otherwise specifically provided for foundation, filling and mass concrete complete and including removing rubbish off the permises complete all as directed. |
| 20 | M&L for Forming jambs, etc. to openings in Cement mortar 1:4 or cement lime mortar 1:2:9,including cutting, toothingand properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified. |
| 21 | M&L for Making good under cills or over arches, lintels and bressummers in Cement mortar 1:4 or cement lime mortar 1:2:9. including allpinning when necessary cmplete all as specified. |
| 22 | Demolition ofreinforced cement concrete of any description and in any position not otherwise specifically provided for RCC Chajjas/Roof projections etc complete all as specified and as directed. (Reinforcement cut as required to facilitate demolition) |
| 23 | Dismantling floor hearth or existing wall tiling incl cement mortar bedding (but not backing) including removal of debris from the site, etc complete all as specified and as directed |
| 24 | Taking down chowkats or steel window /ventilators /door frames with shutters (without taking off shutters from frames) not exc 1.5 Sqm each complete all as specified and as directed. |
| 25 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) etc complete all as specified and as directed. |
| 26 | Taking up or down upto 25 mm bore ofpipe steel tubing and connections, including for refixing or removal etc complete all as directed. |
| 27 | M & L Providing Reinforced cement concrete (Design mix M-25), as in foundation Beams,plinth beams,bases for columns, etc, basement slabs, under-reamed piles and mass concrete and similar works etc completed all as specified and directed. |
| 28 | M & L Providing Reinforced cement concrete (Design mix M-25), as in Beams, lintels over 1.50m span , and similar works etc completed all as specified and directed. |
| 29 | Formwork tosoffits of suspended slabs such as roof slab ,floor slab,landing and similar work not exc 200 mm thick , complete all as specified and directed. |
| 30 | M & L Providing Reinforced cement concrete (Design mix M-25), as in Slabs supportedon walls, beams and coloums in floors roof landing, balcones conopes deck slab and in shelves all as directed . |
| 31 | Formwork tochajjas, troughs and similar items including edgescomplete all as specified and directed. |
| 32 | M & L Providing Reinforced cement concrete (Design mix M-25), as in Slabs supported on wall beams and in chajjas all as directed . |
| 33 | M&L for precast Reinforced cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregate), as in Wash hand basin platform slabs, etc including necessary form work set in CM 1:4, complete all as specified and as directed. |
| 34 | S&F mild steel TMT bar 6 mm to 8 mm dia. and over, cut to length , bent to shape as required, hooking ends and bining with and including mild steel wire (annealed) not less than 0.9 mm dia. Used in stirrups, spacers and binders, complete all as specified and directed. |
| 35 | S&F PVC (SWR) pipes 110 mm bore single socketted in any length with rubber ringjoints laid in trenches or floorsetc complete all as specified and as directed |
| 36 | S&F PVC (SWR) pipes 110 mm bore single socketted in any length with rubber ringjoints fixed to walls,, etc complete all as specified and as directed |
| 37 | S&F PVC (SWR) pipes 75 mm bore single socketted in any length with rubber ringjoints laid in trenches or floors or in walls, etc complete all as specified and as directed |
| 38 | S&F PVC (SWR) pipes 75 mm bore single socketted in any length with rubber ringjoints fixed to walls, etc complete all as specified and as directed |
| 39 | S&F PVC (SWR) bends any radius suitable for 110mm bore pipe, etc complete all as specified and as directed |
| 40 | S&F PVC (SWR) bends with oval access doors any radius suitable for 110mm bore pipe, etc complete all as specified and as directed |
| 41 | S&F PVC (SWR) branch piece, 110mm,single (single Y or T) equal or unequal etc complete all as specified and as directed. |
| 42 | S&F PVC (SWR) branch piece , 110mm, Double (double Y) equal or unequal etc complete all as specified and as directed. |
| 43 | S&FPVC (SWR) \"P’ trap110mm etc complete all as specified and as directed. |
| 44 | S&F PVC (SWR) bends any radius suitable for 75mm bore pipe, etc complete all as specified and as directed |
| 45 | S&F PVC (SWR) bends with oval access doors any radius suitable for 75mm bore pipe, etc complete all as specified and as directed |
| 46 | S&F75mm dia PVC (SWR) floor/nahani trap plain with grating including jointing with solvent cement and jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc complete all as specified and as directed. |
| 47 | Supply and fixSalt glazed stoneware gully trap, type Q 125x100mmmm,complete all as specified and as directed. |
| 48 | S&F 15 mm bore steel tubing medium grade galvanised with all fittings and fixed complete to walls, ceilings or laid in floors etc complete all as specified and as directed. |
| 49 | Cutting chases, pinning in stone or brick walls and making good to facings where required and pointing in cement mortar 1:3 and cutting not exc 10 cm girth etc complete all as specified and as directed. |
| 50 | S&F 20 mm bore steel tubing medium grade galvanised with all fittings and fixed complete to walls, ceilings or laid in floors etc complete all as specified and as directed. |
| 51 | S&F 25 mm bore steel tubing medium grade galvanised with all fittings and fixed complete to walls, ceilings or laid in floors etc complete all as specified and as directed. |
| 52 | M&L for rendering10 mm thick in CM 1:3 onconcrete surfaces asceillingfinished even and smooth (without using extra cement) of any description and in any position, with necessary scaffoldings complete all as specified and as directed by theEngineerin-Charge. |
| 53 | M & L for Joint free non - skid coloured ceramic tiles, 10 mm thick (square or rectangular) area of each tiles exceeding 0.72 sqm but not exceeding 1.20 sqm,as in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles, complete all as specified and directed. |
| 54 | M&L for Screed bed or bedding layer of cement mortar (1:6) 15mm thick for laying floor tiles/floor finishes. |
| 55 | M&L for rendering 10mm thick in cement mortar 1 : 4 on brick or concrete surfaces to receive as backing of wall tilingetc complete all as specified and as directed. |
| 56 | M&L Joint free Glazed coloured ceramic tiles of digital quality in vertical surfacesize of each tile exceeding 0.72 sqm but not exceeding 1.20 Sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match (Note: Colour of tile will be finalized by Engr-In-Charge) |
| 57 | S&F of 18 to 20 mm thick Granite work (table rubbed and polished) black coloured, for WHB platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and as directed. |
| 58 | M&L for screed bed or bedding layer of mortar 20mm thick for laying granite stone of WHB/floor finishesin CM (1:6) etc complete all as specified. |
| 59 | S&F of 18 to 20 mm thick Granite work (table rubbed and polished) black coloured,for wall lining (veneering to wall ) 12mm thick in cement mortar (1:3) and pointing withwhite cement (1:2) using marbel dustwith admixture of pigment to match with shade of granite etc complete all as specified and as directed. |
| 60 | M&L rounding to edges of stone slabs one edge, in cooking plotforms complete all as specified |
| 61 | S&F Powder coated aluminium ventilators of approximate size 600mm x 900mm, top hung type made out of anodised aluminium extruded section of thickness not less than 1.50 mm,suitable aluminium hinges, aluminium tower bolts, rubber gasket, aluminium beading, suitable fancy type handles and including all other required fittings as per standard engg. practice, complete all as specified and directed. |
| 62 | S&F Powder coated (Thickness not less than 50micron) Aluminium anodised Grill, aperture n exc 75 mm ,size 6mm x 4mm thick, including 1 mm thick channel fixed with steel screws complete all as specified and directed. |
| 63 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, etc complete all as specified and as directed |
| 64 | S&F 4 mm thick frosted glass, pin head type and glazing with oil putty in squares n .exc0.5 sq. m in each pane complete all as specified and directed by Engr-in -Charge. |
| 65 | M&L Cement concrete type B-1 1:2:4 (20mm graded aggregate) inroof padding concerte of average50 mm thick with liquid water proofing compound as per manufacturers instructions etc complete all as specified and as directed. Note: WPC will be measured & paid separately under relevant Item |
| 66 | M & L Cement concrete type B-0 1:2:4 (12.5mm grades aggregate) in haunching concrete etc complete all as specified and as directed |
| 67 | M&L forRendering 10mm thick in cm 1 : 3 mixed with liquid water proofing compound as per manufacturers instructionson concrete surfaceswhen PCC on roof surface is still green including finished even and fair etc complete all as directed Note: WPC will be measured & paid separately under relevant Item |
| 68 | Cleaning the roof surfaces and applying oil bound bitumen primer @0.20 Kg per Sqm providing and laying 4mm thick APP modified water proofing membrane weight not less than 4 Kg per Sqm reinforced with non woven polyster mat weight not less 160 gm per Sqm having softening point not less than 140 Degree centgrade, lengitudinal tensile strength not less than 800N per 5 cm teasing strenght of 180N with minimum of 10 cm side laps and 15 cm end laps by application of torch. Applying a coat of blown grade hot bitumen over the membrane @ 1.20 kg/sqmas per manufacturer instructions complete as directed |
| 69 | M&L for applying one coat of solar reflective bituminous Aluminium paint over a surface of APP water proofing membrane @ 0.1 Kg/Sqmetc complete all as specified and as directed. |
| 70 | Supply only Liquid water proofing compound. |
| 71 | S&F1000 ltrs of capacity Rotational moulded polyethylene water storage tanks with cover (cylindrical vertical with closed top) hoisted and fixed in positionetc complete all as specified in SSR Part I and as directed. |
| 72 | Supply and fix 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe (minimum weigh 210 gms) complete all as specified and as directed. |
| 73 | S&F in repair of Gun-metal globe or gate valves 20mm bore dia with iron wheel head, screwed both ends for iron pipes etc complete all as specified and as directed. |
| 74 | S&F in repair of Gun-metal globe or gate valves 25mm bore dia with iron wheel head, screwed both ends for iron pipes etc complete all as specified and as directed. |
| 75 | S&F in repairs wall Hung EWC of make : Cera (capitol) of snow white colour size (530x350x375 mm) Cat. No. S1044150 P Trap or equivalent with duroplast slim soft close seat cover etc all complete and as directed by Engineer-in-Charge. |
| 76 | S&F in repairs concealed cistern set with full frameincluding all accessories of Make : Cera (Chevron) Cat. No. B1110111 or equivalent (without Knob) etc all complete and as specified. |
| 77 | S&F in repairs Q type shine finish Knob for concealed chevron cistern setincluding all accessories of Make : Cera (Chevron) Cat. No. B11210104 or equivalent etc all complete and as specified. |
| 78 | S&F in repairs Health faucet ABS body with 1 meter SS braided connection pipe of make : CeraCat. No. F8030109AB or equivalent all complete and as specified. |
| 79 | S&F in repairs Toilet paper holder with flap guard of make : Cera (Hera range) Cat. No. F5007110 or equivalent all complete and as directed. |
| 80 | S&F in repairs Grating doom of 100 mm dia of Stainless steel hinged or openable type ,fixed with suitable solvent cement complete as specified. |
| 81 | S&F in repairs 2-Way bib cock with side handle, wall flange and aerator of make: Cera (winslet) Cat. No. F1099161 or equivalent complete all as specified and directed. |
| 82 | S&F in repairs table top Wash Hand Basin of size 750 x 380 x 130 mm of snow white colour of make : Cera (Catmega) Cat. No. S2020160 or equivalent complete all as specified and directed. |
| 83 | S&F in repairs 32 mmwaste coupling with ceramic pop-up push type (full threaded) of make: Cera Cat. No. F8050351 or equivalent all complete and as specified. |
| 84 | S&F in repairs polyamide braided connection pipe 12 mm dia, 450 mm length (02 piece set) of make: Cera Cat. No. F8070402 or equivalent all complete and as specified. |
| 85 | S&F in repairs single lever Wash hand Basin mixer with 450 mm braided connection pipe (without pop up) of Make : Cera (winslet) Cat. No. F1099451 or equivalent all complete and as specified. |
| 86 | S&F in repairs of High density polyethylene pipes 32mm(HDPE) with collar of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors including concealing the pipe as per site requirement etc all complete and as specified and directed. |
| 87 | S&F in repairs angle cock with wall flange of Make : Cera (winslet) Cat. No. F1099201 or equivalent all complete and as specified. |
| 88 | S&F in repairssoap dish of make : Cera ( Hera range) Cat. No. F5007106 or equivalent all complete and as specified. |
| 89 | S&F in repairs Tumbler holder of Make : Cera (Hera range) Cat. No. F5007107 or equivalent complete all as specified. |
| 90 | S&F in repairs Liquid soap dispenser of make : Cera (Hera range) Cat. No. F5007111 or equivalent complete all as specified. |
| 91 | S&F in repairs Towel ring of make : Cera (Hera range) Cat. No. F5007105 or equivalent complete all as specified. |
| 92 | S&F in repairs Towel rail 600 mm long of make : Cera (Hera range) Cat. No. F5007103 or equivalent complete all as specified. |
| 93 | S&F in repairs Towel rack 600 mm long of make : Cera (Hera range) Cat. No. F5007101 or equivalent complete all as specified. |
| 94 | S&F in repairs wall mixer (3-in-1) with arrangement for both telephonic hand shower and overhead shower with bend pipe of make : Cera (Winslet) Cat. No. F1099403 or equivalent complete all as specified and directed. |
| 95 | S&F in repairs overhead rain shower of stainless steel of size 300 x 300 mm of make: Cera Cat. No. F7010109SS or equivalent complete all as specified and directed. |
| 96 | S&F in repairs overhead shower arm 230 mm long with wall flange of make : Cera Cat. No. F7040103 or equivalent complete all as specified and directed. |
| 97 | S&F in repairs hand shower of stainless steel of size 100 x 125 mm with three flow, wall hook and 1.5 meter hose of make: Cera Cat. No. F7030308AB or equivalent complete all as specified and directed. |
| 98 | S&F in repairs corner glass shelf with 2 racks of Make : Cera (Oceana range) Cat. No. F5005201 or equivalent complete all as specified and directed. |
| 99 | S&F in repairs glass shelf of Make : Cera Cat. No. F5001114 or equivalent complete all as specified and directed. |
| 100 | S&F in repairs 5 mm thick glass mirror of size 800 x 600 mm with double coat for protection and longevity, 5 mm clear glass shelf with stainless steel rail and silver plating on the back for better reflection of Make : Cera Cat. No. B3510149 or equivalent complete all as specified and as directed. |
| 101 | S & F Powder coated aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators, partitions with one or more rebates including joining cleat for fixing etc.complete all as specified and directed. |
| 102 | S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators, partitions (fixed partitions) with extruded built up standard tubular sections / appropriate Z sections and other sections of aproved make conforming to IS- 733 and IS- 1285, with dash fasteners of required dia and size, including neccessary filling up the gaps at junctions, i.e.at top, bottom ad sides with required EPDM rubber / neoprene gasket etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, CP brass / stainless steelscrews, all complete as per architctural drawigs and the directions of Engineer-in-charge. |
| 103 | S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for type of shutters of doors, windows, ventilators, including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections / appropriate Z sections and other sections of aproved make conforming to IS- 733 and IS- 1285, with dash fasteners of required dia and size, including neccessary filling up the gaps at junctions, i.e. at top, bottom ad sides with required EPDM rubber / neoprene gasket etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, CP brass / stainless steelscrews, all complete as per architctural drawigs and the directions of Engineer-in-charge. |
| 104 | S & F 12 mm thick Toughened glass as in hinged doors / sliding doors, partitions automatic doors and similar work including cutting to shape, drilling holes as required, complete all as specified and directed. |
| 105 | Complete removal of the existing treatment on ceiling and applying two coats of distemper oil emulsion over a coat of primer including preparation of surfaces complete all as specified and directed by Engineer-in-Charge. |
| 106 | M&L for preparing of newly plastered surfaces of ceiling and applying two coats of distemper oil emulsion over a coat of primer including preparation of surfacescomplete all as specified and as directed. |
| 107 | M&L for Cutting holes (Through) of size not exc. 150 Sqcm into existing manholes of brick walls builtin cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required and directed. |
| 108 | Demolition ofplain cement concrete of any description and in any position not otherwise specifically provided for SGSW drain pipes complete and including removing rubbish off the permises complete all as directed. |
| 109 | Demolition, breaking up and removal of 100mm dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar andin any position, all as specified and as directed. |
| 110 | M&L for PCC 1:4:8, type D-2 (using 40mm graded stone aggregate) for concrete bed of 10cm thick, to drain pipes of 100 mm dia,including packing under, and hunching against the sides of pipes after they are laid and tested, complete all as specified and as directed. |
| 111 | M&L for 100 mm dia pipe (Grade ‘A’ pipe) Salt glazed stone ware drain pipes laid in trenches and jointed in CM 1:3 complete all as specified and directed.Make: Indo/Khandelwal/ Mancheryal Ceramics |
| 112 | M&L for brick work for sewage chamber with sub class `B\" brick (old size bricks) straight or curved on plan exceeding 6 m mean radius built in CM 1:4, complete all as specifiedand as directed. |
| 113 | M&L for PCC 1:2:4, type B-0 (20 mm graded stone aggregate) as in copings for sewage chamber, bed plates, valley gutters, kerbs etc including necessary form work complete all as specified and as directed. |
| 114 | M&LPCC (1:2:4) type B-1, using 20 mm gradedstone aggregateas in surface channels for sewage chembers and benching at bottom of drains including forming fair finishes to drains/channels etc complete all as specified and directed. |
| 115 | M&L for hardcore of gauge n exc. 63 mm of broken stone boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface. |
| 116 | M&L 75 mm thick PCC (1:4:8) type D2 (40 mm graded aggregate) as in sub base for floors all as specified and as directed. |
| 117 | M&L for 25 mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floor finished even and smooth using extra cement complete all as specified. |
| 118 | M&L for 75mm thick plain cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in top layer of plinth protection, path etc.,finished even and smooth without using extra cement complete all as specified and as directed. |
| 119 | Forming Construction joint 30mm deep x 10mm wide filled with sealing compound, Grade ‘A, all as specified and as directed. |
| 120 | Removal of debris (Aggregates) obatained from demolitionincluding loading and unloading to a distance of 5km from the starting point and deposited where directed etc complete all as specified and as directed. |
| 121 | M&L for Cuttingintoexistingmanholes for connecting new drains upto 225 mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required all complete and as specified. |
| 122 | M & L for Point wiring with 1.5 Sqmm copper conductor unsheathed, multistranded, PVC insulated, single core cable FRLSwith earth continuity conductor of 1.5 sqmm PVC insulated copper conductor and including rigid PVC conduit of suitable size but not less than 20mm dia. and allaccessories fixed to be consealed in wall & surface of the roof etc., including modular type terminal boxes made out of Galvanised sheet of thickness should be not lessthan 0.9mm thickfor fixing of modular switches, modular fan regulators, modular socket outlet etc along-with suitable modular plate for housing switches, etc complete all as specified and as directed. |
| 123 | (a) One light point controlled by one switch |
| 124 | (b) One Fanpoint controlled by one switch |
| 125 | (c) One three pin socket 5 Amps plug point independent |
| 126 | (d) One three pin socket 5 Amps plug point on same board |
| 127 | All as per Ser item No 1 above but with 2.5 sqmm copper cable in and including PVC conduit complete all as specified and as directed for 15Asocket. |
| 128 | S&F of ceiling rose, three terminal, PVC/polycarbonate, insulated body, ISI markedcomplete all as specified and as directed. |
| 129 | S&F ofModular Switch type polycorbonate white 1 way, 6A,240Volts complete all as specified. |
| 130 | S&F ofModular Socket outlet polycorbonate white 10A - 2/3 pin complete all as specified. |
| 131 | S&F ofModular Switch type polycorbonate white 1 way, 16A,240Volts complete all as specified. |
| 132 | S&F ofModular Socket outlet polycorbonate white 20A - 2/3 pin complete all as specified. |
| 133 | S&F surface mounting / wall mounted LED tube light fitting 1x20/18wattshigh efficiency, anti glare, maintenance free operation including LED driver and mounting arrangements, all accessories internally pre-wired, connecting up with twin core twisted flexible copper conductor cable white colour with suitable size including taking out old unserviceable one complete all as specified and directed by Engineer-in-Charge. |
| 134 | S&F surface type LED mirror light12 Watt with inbuit driver 230 V with all accessoriesinternally pre-wired and includingconnecting up with twin core twisted flexible copper conductor cable with suitable size acomplete all as specified and directed by Engineer-in-charge Model No-Luker Cat No- LMCL12 Havells / Phillips /Bajaj / CG/ Luker |
| 135 | M&L for Sub Main wiring with two runs of 6sq mm 1100 V grade (nominal area) single core PVC insulated unsheathed cable multi-stranded copper conductor drawn through medium grade, rigid non-metallic PVC conduit consealedof suitable sizewith all necessary fittings, surface in walls/roof/floor duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth dolly complete all as specified and directed by Engineer-in-Charge. |
| 136 | Note:-(i) Necessary PVC dummy plates & PVC rigid junction boxes for identifying junction as required on site/directed by Engr-in-charge shall deemed to be included in the quoted rate. |
| 137 | (ii) The wiring shall be done strictly by following proper colour coding using red, yellow and blue for phase, black for neutral and green for earth leads. |
| 138 | (iii) Three runs of cable and one run of PVC conduit / casing caping will be measured as one uint. |
| 139 | S&F of MCB DB 4 way SPN DB Double door,230volts 50 Hz AC supply including s fixed to the existing wall (concealed/surface) and making good the disturbed surface wall with the exsting wall complete all as specified and as directed. |
| 140 | S&F MCB SPN 6 to 32A, 10KA rupturing capacity complete all as specified and as directed. |
| 141 | S&F Fix MCB SP 6 to 32 A 10 KA rupturing capacity complete all as specified and as directed. |
| 142 | Supply & Fixing exhaust fan withplastic body 200mm sweep, 1325 RPM, Heavy duty single phase 240 Volts, AC 50 Hz and connecting up including louvers and making good with matching colour with the surroundings provision of cable 3 core of size 0.5 Sqmm (16/0.2 mm) from ceiling rose to fan ,including making necessary opening on stone /brick masonry wall and all as specified and as directed. |
| 143 | M&Lfor shifting of existing wall split unit indoor/outdoor AC complete with cordless remote control unit for operation on 230 volts, 50 Hz single phase AC supply and outdoor (condensing) unit to be installed on 25mmx25mmx 3mm new angle iron frame fixed on brackets duly painted complete in all respect of all including refilling of gas and copper refrigerant pipes for suction & discharge lines of standed size as requried duly insulated condensate water outlet PVC pipe laid up to ground level and 3 core copper wire of reqired lenght for stablizer to indoor/outdoor unit all as specified and as directed. |
| 144 | M&L Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240 V, 50 Hz AC completeall as directed |
| 145 | M&L moter starter 16 Amp 2 module including necessary metal box and cover plate all as directed |
| 146 | M&L RCC1:2:4 type B1 (20mm graded aggregate) for foundation including rafts footing ,foundation beams plinth beams bases for columns etc basement slab,under reamed piles and mass concrete |
| 147 | M&L RCC 1:2:4 type B1 (20mm graded aggregate) for Columns, pillars, piers, posts and struts |
| 148 | Formwork to flat rough finished surfaces of conrete sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batterfair finished surfaces. |
| 149 | Formwork to square rectangular rough finished surfaces of concrete sides of pillars, posts, struts, piers, columns and stanchions fair finished surfaces. |
| 150 | S&F of Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 |
| 151 | S&F plates (plain or corrugated) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410(Gde-250) |
| 152 | S&F Mild screw bolts ( Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut,exc 5 but n exc 10 cm long dia of shank 11 to 15mm. |
| 153 | S&F Mild screw bolts ( Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut,exc 22.5 but n exc 30 cm long dia of shank 16 to 20 mm. |
| 154 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugatedsteel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, chajjas, fixed with self tapping screws as specified. |
| 155 | S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge of roof covering/ cladding to wall, chajjas, valley gutter, fixed with self tapping screws as specified. |
| 156 | M&L preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide/zinc chrome primer complete all as specified and as directed. |
| 157 | M&L 100mm thick PCC (1:2:4) type B2 (40 mm graded aggregate) finishing cement concrete surface even and smooth Without using extra cementas infloors all as specified and as directed. |
