Public Works Department-PWD has published Construction Of Building Of Govt. Polytechnic Talawar (Sh:- C/O Amenity Block Including Water Supply, Sanitary Installation, Rain Water Harvesting System And Septic Tank).. Submission Date for this Tender is 16-01-2024. Building Work Tenders in jaisinghpur Himachal Pradesh. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Earthwork in excavation by mechanical means (Hydraulic excavator)/ manualmeans over areas (exceeding 30 cm (thirty centimetre) in depth, 1.5 m (one point five metre in width as well as 10 sqm (ten square metre) on plan) including getting out and disposal of excavated earth lead upto 50 m (fifty metre) and lift upto 1.5 m, (one point five metre)as directed by Engineer-incharge within all leads, lifts and other incidentals, as per approved drawing, design, specifications and as directed by the Engineer-in-Charge. The rate is inclusive of octori, royality, Malkhana, toll taxes, GST and any other taxes imposed by the Government. |
| 2 | Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Foundation, footings basis of columns etcetera and mass concrete including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 3 | Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle ironframe 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetera upto any thicknessincluding carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 4 | Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work inBeams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 5 | Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work inColumns, Pillars, Piers, Abutments, Posts and Struts up to all width and heightsincluding carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 6 | Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stairs, (excluding landings) except spiral-stair cases up to all width and heightsincluding carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 7 | Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls up to all width and heightsincluding carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 8 | Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling not exceeding 4 Mtrs and removal of the same for insitu-reinforced concrete and plain concrete work in Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the likeincluding carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 9 | Providing form work with steel plates of 3.15mm thick,welded with angle iron in frames of 30mmx30mmx5mm, so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Vertical surfacesas walls ant thickness including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 10 | Providing and laying cement concrete 1:4:8 (One cement: four sand: eight graded crushed/broken stone aggregate 40mm (forty millimetre) nominal size ) and curing complete, excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 11 | Supplying & Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rate is inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 12 | Stone Filling in plinth with approved quality under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rate is inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 13 | Providing and laying in position machine batched and machine mixed design mix M-25 grade ( M-twenty five) cement concrete for reinforced cement concrete work, using cement content as per approved design mix,Cement content considered in this item is @ 330 kg/cum. (three hundred thirty kilogram) All works upto plinth level including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 14 | Providing and laying in position machine batched and machine mixed design mix M-25 grade ( M-twenty five) cement concrete for reinforced cement concrete work, using cement content as per approved design mix,Cement content considered in this item is @ 330 kg/cum. (three hundred thirty kilogram) All works above plinth level upto floor V level including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 15 | Coursed rubble masonry (first sort) with hard stone in foundation and plinth with Cement mortar 1:6 ( one cement :six coarse sand) including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 16 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm (Twenty millimetre) nominal size) upto plinth level with :Cement mortar 1:6 ( one cement : Six coarse sand)including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 17 | Steel reinforcement TATA TISCO/SAILfor reinforced cement concrete work including strengthening, cutting, bending, binding and placing in position complete and binding all complete avobe plinth level TMT bar grade Fe-500 (FE- Five Hundred) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 18 | Providing and Laying damp-proof course 100mm (one hundred milimetre) thick with cement concrete 1:2:4 (one cement : two sand : four graded stone aggregate 12.5mm (twelve point five milimetre) nominal size)including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 19 | Providing and applying a coat of residual petroleum bitument of grade of VG-10 (VG- ten) of approved quality using 1.7 Per Kilogram (one point seven kilogram). Per quare metre on damp proof courase after cleaning the surface with brushes and finally with a piece of cloth lightly coaked in kerosene oil.including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 20 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to all floor level.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 21 | Brick work with common burnt clay machine moulded With F.P.S. (non modular)perforated bricks of class designation 12.5 (twelve point five) conforming to IS: 2222 in superstructure above plinth level up to allfloorlevel in cement mortar 1:6 (one cement : six coarse sand) : The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 22 | Second class brick masonry wall having overall thickness of 40 cm (forty centimetres) usingcommon burnt clay building bricks in superstructure upto floor all levels with hoop iron and cross tiles 8 mm (eight millimetre) dia steel bars in Z shape, laisin cement mortar 1:3 (one cement is to thre sand) including two number 11.5 cm(eleven decimal five centimetres) thick wall internal cavity 17 cm (seventeen centimetres) wide (Area of only one face will be measure for payment) complete as perspecifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 23 | Providing and fixing coloured anodised aluminium frames for door, frame (External door No. S2965 size125x42.4x1.44 mm (one hundred twenty five into forty two decimal four into one decimal four four millimetres ) and Internal door section No 14007 82.60x38.10x3.25 mm,(Eighty two decimal six zero into thirty eight decimal one zero into three decimaltwo five millimetre) window, ventilators and partitions frame with extruded built up standardtubular and other sections of approved make Jindal/HindalcoIS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws. All complete as perspecifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 24 | Providing and fixing coloured anodised aluminium frames for door,window, ventilators and partitions shutter with extruded built up standardtubular and other sections of approved make Jindal/HindalcoIS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws. All complete as perspecifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 25 | Fly proof stainless steel (Grade 304) wire gauge with 0.5 mm (zero decimal five millimetre) dia. wire and 1.4 mm(one decimal four millimetre)aperture on both sides in existing Aluminium shutters and nut and bolts complete.All complete as perspecifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 26 | Providing and fixing aluminium 8 mm thick (eight millimetre) grill anodised powder coated pattern to existing window/ventilatior with 80mmx80mm (eighty into eighty millimetres)panels holes with 25x8mm thick(twenty five into eight millimetres)aluminium flat in windows and ventilators including fixing with aluminium screws or bolts and nuts complete in alluminium channels base frames (Aluminium channels base frames to be measured and paid for separately)as perspecifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 27 | Providing and fixing factory made P.V.C. door frame of size 50x47mm (fifty into forty seven millimetre)with a wall thickness of 5 mm,(five millimetre)made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm (one hundred fifty millimetre) long brackets of 15x15 mm (fifteen into fifteen millimetre) M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm(nineteen into nineteen millimetre)M.S. square tube of 19 (nineteen) gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 28 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 (nineteen) gauge thickness and size of 19 mm x 19 mm (nineteen into nineteen millimetre) for styles and 15x15 mm (fifteen into fifteen millimetre) for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm (five millimetre) thick heat moulded PVC "C" channel of size 30 mm(thirty millimetre) thickness, 70 mm (seventy millimetre)width out of which 50 mm (fifty millimetre) shall be flat and 20 mm (twenty millimetre) shall be tapered in 45(forty five) degree angle on both side forming styles and 5 mm (five millimetre) thick, 95 mm (ninety five millimetre)wide PVC sheet out of which 75 mm (seventy five millimetre)shall be flat and 20 mm (twenty millimetre) shall be tapered in 45 (forty five) degree on the inner side to form top and bottom rail and 115 mm(one hundred fifteen) wide PVC sheet out of which 75 mm (seventy five millimetre) shall be flat and 20 mm (twenty millimetre) shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the "C" Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer"s specification & drawing. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 29 | Providing and fixing 12 mm (twelve millimetre)thick phenol Bonded both sideprelaminated BWP grade particle board panels matt finush flat pressedthree layer or graded wood particle board conforming to IS: 12823 Grade lType ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete asper architectural drawings and directions of engineer-in-charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 30 | Providing and fixing 1.0mm thick P.G.I Sheet lining on inner side of SDB shutters with screws and nails completeas per specifications, approved drawing, design,as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 31 | Providing and fixing glazing with glass pans of 6 mm (six millimetre) thick of modigaurd weight not less than 15.00 kg/ sqm (fifteen kilogram per square metre) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge . (Cost of aluminium snap beading shall bepaid in basic item and as per specifications, approved drawing, design,as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 32 | Providing and fixing glazing with 5 mm thick of modigaurd weight not less than 12.50 kg/ sqm. (Twelve point five zero kilogram per square metre) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge . (Cost of aluminium snap beading shall bepaid in basic item and as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 33 | Providing and fixing glazing with 4 mm yhick prosted glass of modigaurd weight not less than 12.50 kg/ sqm. (Twelve point five zero kilogram per square metre) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge . (Cost of aluminium snap beading shall bepaid in basic item and as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 34 | Providing and fixing 19mm (nineteen millimetre) thick water proof termite resistant commercial board confirming ply wood of ACTION TESA GREENPLY and 19 mm (ninteen millimetre) thick water proof commercial board shelves and shutters , theback side of cup board / cabinat shall be finished with 8 mm (eight millimetre) thick preliminated MDF board and all the cut portion of shelves shall be finished with 1 mm thick pre-lamination/ 4 mm (four millimetre) thick veneer pasted over shutter to be polished.All internal surfaces of cup board shall be laminated with 1 mm mica of approved shade.All cut portion ofshelves shall be finished with 6 mm (six millimetre) thick hard wood edging. The shutter of cup board from all sides shall be finished with 6mm /12 mm (six/twelve millimetre) hard wood edging including all fitting piano hinges and magnetic catcher with in all accessories etctera complete as per given specification and as per direction of Engineer-in Charge including all leads and carriage of material.The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 35 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm (one decimal two five millimetre) with twochromium plated brass brackets fixed with C.P. Brass screws and PVC sleeves etctera wherever necessary complete20 mm (twenty millimetre) Dia as per given specification and as per direction of Engineer-in Charge including all leads and carriage of material.The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 36 | Providing and fixing 300x16 mm (three hundred into sixteen millimetre) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 37 | Providing and fixing 250x16 mm (two hundred fifty into sixteen millimetre) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 38 | Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetraetera complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 39 | 200 X 10 mm (two hundred into ten millimeter) size |
| 40 | 150 X 10 mm (one hundred fifty into ten millimeter) size |
| 41 | Providing and fixing aluminum handles anodized transparent or dyed to required colour and shadewith necessary screws etcetraeteracomplete as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 42 | 150 mm (one hundred fifty millimeter) size |
| 43 | 125 mm (one hundred twenty fivemillimeter) size |
| 44 | Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etctera complete.as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 45 | Providing and fixing ISI marked hydraulicdoor closer with necessary screws etctera complete as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 46 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etctera complete as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 47 | Providing and laying 19 mm (nineteen millimetre) thick Polished Grey Chima Pink Granite Stone having Semi / Round nosing in work top ofKitchen / Pantry and Counter Top of Bank and ATMlaid over 20mm (twenty millimetre) (average) thickness base of cement mortar 1:3 (1cement: 3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete as per Architectural drawing ,design and specifications.including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 48 | Providing and laying25mm (twenty five millimetre) thick mirror polished kota stone 55x 55 cm (fifty five into fifty five centimetre)of uniform colour with 7.5 cm(seven decimal five centimetre) wide Jaisalmer Yellow marble band of the same shade as that of flooring single slush skirting spread sky having sami round nosing, riser of step single slab where required laid on 20mm (twenty millimetre)thick base in cement mortar 1:4 ( one cement is to four sand ) mix with pigment to match the shade of the kota stone i/c rubbing andmirror polishing complete as per approved drawing, design and speciations including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 49 | Providing and laying25mm (twenty five millimetre) thick mirror polished kota stone 55x 55 cm (fifty five into fifty five centimetre)of uniform colour inflooring and skirting laid on 20mm(twenty millimetre) thick base in cement mortar 1:4 ( one cement is to four sand ) mix with pigment to match the shade of the kota stone i/c rubbing andmirror polishing complete as per approved drawing, design and speciationsincluding carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 50 | Providing and laying 60x 60cm (sixty into sixty centimetre) Vitrified tiles of Orient/Bell/RAK of approved shade in floor and skirting with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, includinggrouting of joints (Payment for grouting of joints to be made separately)and as per approved drawing, design and speciations including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 51 | Providing and Fixing 3.9 mm (three decimal nine millimetre)Thick Taraflex flooring skirting Gerflor of approved shade as per specification, approved drawing , design and as per the direction of the Engineer- In- Charge complete in all respect. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 52 | Providing and laying automatic hydraulic compressed and polished Precast terrazzo tiles of ISI marked No.1237 of size 300 x 300x 25mm thick vibro compacted of NTC in 70% white & 30% grey cement with chips 55% white 15% each Marron, Yellow and dark green of size 0,B,2Blaid in floors,landings laid on a bed of 20 mm (twenty millimetre) thickness of cement mortar 1:4 (1 cement : 4 Sand) jointed with cement slurry mixed with pigment to match the shade of tiles (Wherever required) including rubbing , polishing Complete and of approved shade as perspecification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 53 | Providing and laying Double charge Vitrified tiles in different sizes of Orient/Bell/RAK of approved shade(thickness to be specified by manufacturer),in flooring/skirtingwith water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade,riser of steps, over 12 mm (twelve millimetre) thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etctera complete.600x600x10 mm (six hundred into six hundred into ten millimetre)as perspecification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 54 | Providing and laying 300X300 mm / 400x400mm (three hundred into three hundred / four hundred into four hundred millimetre) antiskid ceremic tiles of Premium Quality of Nitco/AGL/RAK/Orient -Bell/ Kajaria/Somany //Johnson tiles as per approved shadein flooring laid on 20 mm (twenty millimetre) thick in cement mortar 1:4 (1cement: 4 sand) Jointing with grey cement slury @ 3.30 kg/sqm including painting the joints with cement and matching pigment etctera finished with flush pointing in white cementasper approveddrawing , design and specifications.as perspecification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 55 | Providing and laying 300X450 mm (three hundred four hundred fifty millimetre) Ceremic Glazed tiles of Kajaria/ Nitco / Simpolo/Somany / Orient & Bell / RakL/Johnson in Dado / skirting, and risers of steps over 12 mm (twelve millimetre) thick bed with cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry @3.30 kg per square metre finished with flush pointing in white cement mixed with pigmentto match the shade of tiles completeasper approveddrawing , design and specifications as perspecification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 56 | 50 mm (fifty millimetre) thick cement concrete flooring skirting1:2:4 (1 cement:2 sand:4 graded stone aggregate 20 mm(twenty millmetre) nominal size)laid in one layer finished with a floating coat of neat cement completeasper approveddrawing , design and specifications as perspecification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 57 | Providing and fixing glass strips in joints of terrazo/ cement concrete floors 40x4mm (forty into four millimetre) asper approveddrawing , design and specifications as perspecification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 58 | Providingandlaying 40mm (forty millimetre) average thick Redsandstoneslabflooring in ramp for person with disability on 20mmaveragethickbase ofcement mortar1:4(1cement:4sand)laid overand jointedwith grey cementslurry mixedwith pigmenttomatch the shadeof theslabi/crubbing and granite polish finish as per architect standred design and specification complete. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 59 | Providing and fixing40mm (forty millimetre) dia.M.S hollow Pipe hand Rail slip resistant in ramp at two level i e 75cm(seventy five centimetre) and 90cm(ninety centimetre) height welded with 25mm (twenty five millimetre) diametre M.Shollow pipe balusters embedded in cement concrete 60cm C/C and jointing with electrical gas welding at top alongwith hand rail of hollow M.S. pipe of 50mm diametre. It should extend 30cm beyond top and bottom of the ramp as per approveddrawing , design and specifications.The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 60 | Providing and fixing stainless steelknockdownrailing of Kieh AISI 316of 38mm dia handrail fixed on 10X50 mm (ten into fifty millimetre) SS Flat Bluster (Design Code DTS 3-2-163) PLASED AT 1200 MM centre to centrealongwith 3 Nos. @ 16mm (sixteen millimetre) mid rails connected at the side of baluster withfixers. The baluster would be fixed on the floor with cased base plate of minimum 6 mm (six millimetre) thickness base plate shall be concealed with suitable SS 316 grade cover cap edging heightto be taken @ 85 mm from floor level The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 61 | Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with0.60mm (Zero decimal Six zero millimeters) thick pre-painted steel sheet of Tata Dura shine/Reliance/Jindal ( Factory made) shall be having proper Gola / shape withhot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyester of 5 (Five) microns over 5 (Five) micronsprimer coating including fixing with pre-painted iron J or L hooks, bolts and nuts 6mm (Six millimeters) diameter with pre-painted G.I. limpet and bitumen washers complete with all accessories as required as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 62 | Providing and fixing valley 90cm (Ninety centimetre)over all of Tata Dura shine/Reliance/Jindal with0.60mm (Zero decimal Six zero millimeter) thick pre-painted steel sheetwith hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (twenty) microns over 5 (Five) microns primer coating to back coatof polyester of 5 (Five) microrns over 5 (Five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts with EDPM seal. The meterial supplied will be accompanied by test certificate & 20 years warrenty from company against the corrosion fading of colour & manufacture defects and furtheras perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 63 | Providing and fixing prepainted steel sheet roofing of Tata Dura shine/Reliance/ Jindal over steel trusses of 0.60 mm thickness (ISI marked Z-120) over steel truss prepainted galvanized steel and hot dipped metallic zinc coat sheet with top coat of regular modified polystar (RMP) organic coating of 20 (twenty ) micron over 5 (Five) micron and back coating of polystar 5 (five) micron over 5 (five) micron primer coating including fixing with prepainted ironJor L hooks, bolts , nuts 6 mm (six millimeter) dia with prepained limpat and rubber washers complete with all accessoriesas perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 64 | Providing and fixing 15 cm (fifteen centimetre) wide, 45 cm (forty five centimetre) overall semi circular plain G.S. sheet gutter having dom shape grading with iron brackets 40x3mm(forty into three millimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.63 mm (zero point six three millimetre)thick with zinc coating not less than 275 gm/m²(two hundred seventy five gram per square metre)including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 65 | Providing and fixing M.S. ( Mild Steel)B.P. (Black plain) sheet2.00 mm (two millimeter) thick in eaves boards/facia/soffits /ceiling including cutting, fixing, jointing with gas/electric welding to steel roof members and applying a coat of red lead primercomplete (Base members of steel work shall be measured and paid for separately)as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 66 | Providing and laying double coat water proofing treatment onterrace / depressed portion done with Dr. Fixit pidiproof over toilet area polymer modified cementitious coating consisting of cementitious powder and a polymer liquid. Water proof coating shall be done in two coats as follows. After laying the drain pipes, the floor concrete / slabshall be admixed withDr. fixit pidi proof LW@200ml/50 kg bag of cement, if crack are found there at the junction or in between the slab then before applying Dr. Fixit Pidi proof LW, the junction of the wall/ Beams and slab shall be rounded using cement mortar of 1:5 admixed with Dr. Fixit Pidi Proof LM integral water proofing compound conforming to IS:2645 as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 67 | Providing and fixing flashing 38 cm (thirty eight centimetre)overall with 0.60 mm(Zero decimal Six zero millimeter) thick prepainted sheet of Tata Durashine / Sail / Reliance / Jindals steelsin roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete asper approveddrawing , design and specifications.. |
| 68 | Providing and fixing 150mm (oneHundred fifty milimetre) diameter on wall face P.V.C. (D-plast) rain water pipes 2.2mm ( Two decimal Two millimeter) thick of supreme/Finolex/Prince having working pressure not less than 4.50 kg /cm2 (Four decimal five zero kilogram) per square centimeter including filling the joints with approved adhesive complete as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 69 | Providing and fixing on wall face P.V.C. (D-plast) acessories of Supreme/Finolex/Prince/Astral for rain water pipes including filling the joints with approved adhesive completeas perH.P.P.W.D specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 70 | 150mm (One hundred fifty millimtre) diametere PVC Plain bend |
| 71 | 150mm (One hundred fifty millimtre) diametere PVC shoe |
| 72 | Providing and fixing PVC holder bat clamps of approved design to C.I. or S.C.I. rain water pipesand cost of cutting holes and making good the walls etc. 100 mm (one hundred millimetre)including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 73 | Providing and fixing600x600mm (six hundred into six hundred millimetre) DesignerMusk Bison Board ceiling tiles over readymade powder coated metal sheet section Frame work@ 600mm (six hundred millimetre) centre to centre completeasper approveddrawing , design and specifications.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 74 | Steel work of TATA TISCO/SAIL welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint in beams, joist, channels, angle, tee, flat with connecting plates or angle, cleats as in main and beams, hip and jack rafter fixing in rafter, purlin connects to common rafter in trusses completeas perH.P.P.W.D specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 75 | Painting steel work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr. (zero point nine zero liter /10 (ten) Per Square Metre. Over an under coat of primer applied @ 0.80 ltr (zero point eight zero)/ 10 (ten) Per Square Metre. of approved brand and manufacture including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 76 | Applying priming coat: with ready mixed pink or Grey primer of Asian/Nerolacon wood work (hard and soft wood)including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 77 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr. (zero point nine zero liter /10 (ten) Per Square Metre. Over an under coat of primer applied @ 0.75 ltr (zero point seven five)/ 10 (ten) Per Square Metre. of approved brand and manufacture including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 78 | 6mm (Six millimeter) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 79 | 15 mm (Fifteen millimeter) thickcement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floorlevels including arises, internal angles, chamfers androunded angles not exceeding 80mm (Eighty millimeter)in girth and finished even and smooth with cement mortar 1:6 (One cement is to six sand) as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 80 | 15 mm (Fifteen millimeter) thickcement plaster in single coat on fair side of brick/concretes/ stone walls for interior plastering up to all floor levels including arises, internal angles, chamfers androunded angles not exceeding 80mm (Eighty millimeter)in girth and finished even and smooth with cement mortar 1:6 (1 cement : 6 sand) as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 81 | 15 mm (Fifteen millimeter) thickcement plaster in single coat on fair side of brick/concretes/ stone walls for interior plastering up to all floor levels including arises, internal angles, chamfers androunded angles not exceeding 80mm (Eighty millimeter)in girth and finished even and smooth with cement mortar 1:5 (1 cement : 5 sand) as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 82 | 20mm (twenty millimeter) thick Cement plaster in pattern with cement mortar 1:5 (one cementisto five sand) as shown in elevation / drawing upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (Eighty millimeter)in girth and finished even and smoothas perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 83 | 15mm (fifteen millimeter) Cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto anyfloorlevel including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (Eighty millimeter)in girth and finished even and smooth with cement mortar 1:4 (One cement is to four sand) as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 84 | Providing plinth protection with 60mm (sixty millimeter) thick interlocking paver block C.C paver block of M-30 grade with 23 cm diahalf round RCC (Reinforced cement concrete) pipe for drainage purpose laid over 0.10 (zero decimal ten ) thick cement concrete 1:5:10(one cement is to five sand is to ten graded stone aggregate 20mm(twenty millimeter) nominal size) for bedding and haunching of pipe as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 85 | Providing and fixing Unistone slab 12.50 mm clading of NTC/Nitco Atlantic/ unistone surface side on face and porch masonary wall etc. In 12 mm (twelve millimetre) thick cement plaster 1:3 (one cement : three sand) and jointed with cement slurry including scafolding etctera Complete as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 86 | Applying Birla white/JK wall care putty over plaster surface after thoroughly brushing the surface free from mortar dropping, dust, loose material and other foreign matters, sand papered smooth to give final matt finish to the surface complete. as perspecifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 87 | Finishing wall with Fine dune /Dune finish of NCL Alltek / Spectrum Textured wall finish Natural grit of Heritage having coating thickness1.5mm on undecorated wall surfaces to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete as per Architectural drawing ,design and specification including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 88 | Applying two or more coats of Satin Enamel paint of Asian paints / Berger paints / Dulux paints/Nerolac paints ( (up to 150Cm height) of approved shade for interior painting with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic,/special pigment siliceous aggregate anti fungicides anti-rusting & foaming in two coat including necessary putty to give smooth even surface, sand papered smooth complete as per Architectural drawing ,design and specificationsincluding carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 89 | Wall painting (two or more coats) with Premiumemulsion paint of Asian / Dulux /Berger paints/Nerolac paints (above Dado/skirting) of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for matting the surface smoothas per Architectural drawing ,design and specifications. :Interior including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 90 | Painting (two or more coats) with Acrylicemulsion of Asian paints/Berger paints /Nerolac paints(over false ceiling) for interior painting with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic/special pigment siliceous aggregate anti fungicides anti-rusting & foaming in two coat i/c necessary putty to give smooth even surface, sand papered smooth complete as per Architectural drawing ,design and specifications including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 91 | Wall Painting(two or more coats) with syntheticSatin enamel paint of Asian /Nerolac paints (Upto 150Cm height) of approved brand and manufacture and of required shade on ceiling/sloping roof surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper prime. including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 92 | Wall Painting (two or more coats) with synthetic / Acrylic Distemper of approved shade above 150cm height on internal walls of approved brand and manufacture and of required shade onto give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper prime.including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 93 | Distempering with oil bound washable distemper of approved brand asian/Nerolac and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 94 | Providing and fixing polycarbonate transparent sheet 1.20mm (one decimal two zero millimetre) thick in roofing with galvanised J or L hooks bolts and nuts with G.I. Limpet and bitumen rubber washer complete with all accessories as required as per specifications, approved drawing, design anddirection of Engineer-in-Charge The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 95 | Providing and laying in position cement concrete of specified grade of reinforcement concrete excluding the cost of centering and shutteringfinishig andreinforcement- All work up to plinth level : 1:2:4 (one cement : two coarse sand : four graded stone aggregate) 20 mm (twenty milimetre)nominal sizeincluding carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 96 | Providing and laying in position cement concrete of specified grade of reinforcement concrete excluding the cost of centering and shutteringfinishig andreinforcement- All work up to plinth level : 1:3:6 (one cement : three coarse sand : six graded stone aggregate) 20 mm (twenty milimetre)nominal sizeincluding carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 97 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick (fifty millimetre)compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 98 | Providing and fixing in position collapsible steel shutters with vertical channels top andbraced with flat iron diagonals 20 mm X10 mmX2mm (twenty into ten into two millimetre) and braced with flat iron diagonals 20 mm X5 mm (twenty into five millimetre) size with top and bottom rails of T.iron 40 mm X40 mm X6 mm with 38 mm (forty into forty into six with thirty eight millimetre)dia steel pulleycomplete with bolts and nuts locking arrangements, stoppers,handles,including applying a priming coat of red lead paint as per direction of Engineer-in- Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 99 | Making Khurras 45x45 cm (forty five into forty five centimetre) with average minmum thickness of 5 cm (five centimetre) concrete c 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size) over PVC sheet 1m x1mx400 micron finished with 12 mm cement plaster 1:3 (one cement: three sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 100 | Stone filling /Brick aggregate under soak pit including entire carriage of materials including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 101 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in foundations and plinth in CM 1:4 (four coarse sand) including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. satisfaction and direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 102 | Providing and fixing 455x610mm (four hundred fifty five into six hundred ten millimetre) light duty rectangular C.I. manhole with frame cover weight 38 Per Kilogram (thirty eight kilogram) including carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 103 | Providing and laying 110 mm (one hundred ten millimetre) ( to level or slope)approved adhesive pf PVC (D-plast) sewer pipe of working pressure not less than 4.5 kg/Sqm i/c filling the joints with approved adhesive complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 104 | Providing and fixing 1.00 HP water Lifting pump for lifting water from Rain water Harvesting Tank i/c necessary fittingsincluding carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 105 | Providing and fixing 15 mm (fifteenmillimetre) dia nominal bore G.I. Pipes complete with G.I. fittingsincluding treanching and refiling etctera complete .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 106 | Providing and fixing water closet orissa pan No 2071 of size 58x44 CM (fifty eight into forty four centimetre) (Indian type W.C. pan ) of Hindware/Cera with 100 mm (one hundred millimetre) sand P.V.C. P or S trap,10 (ten) litre low level white P.V.C. flushing cistern, includingflush pipe, with manually controlled device (handle lever)with all fittings and fixturescomplete, including cutting and making good the walls and floors wherever required as per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 107 | Providing and fixing white viterous china EWC water closet Pluto cat No 20065 ( S-10) of size 57x35x39 cm (fifty seven into thirty five into thirty nine centimetre) of Hindware/Cera in white shade with Jet pressure and with 10 litre low level PVC flushing cistern with sleek flus andflush system & C.P. flush bend with fittings & C.I. brackets, 40 mm (forty millimetre) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required with W.C. pan with ISI marked white solid plastic seat andas per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 108 | Providing and fixing white viterous china pedestial tpye water closet MATRIX EWC with jet pressure ( European type) of Hindware/Cera in white shade with Jet pressure and,10 (ten) litre low level PVC flushing cistern sleek flus dual having dual flush system& C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required with W.C. pan with ISI marked white solid plastic seat andas per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 109 | Providing and fixing wash basin with C.I. brackets, of DELTA NO 1025ciair of size 55x40 CM (fifty five into forty centimetre)withoutpedestial of HINDWARE /Cera with, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings andbrackets, cutting and making good the walls wherever require:White Vitreous China with 15 mm (fifteen millimetre) dia C.P. bras piller tap of ISI marked IS No. 8934 of Jal ESSESS andas per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 110 | Providing and fixing wash basin with C.I. brackets, of MATRIX with pedestial of HINDWARE /cera with, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings andbrackets, cutting and making good the walls wherever require:White Vitreous China including 15 mm (fifteen millimetre) dia C.P. bras piller tap of ISI marked IS No. 8934 of Jal ESSESS andas per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 111 | Providing and fixing 32mm diameter P.V.C. waste pipe Supreme/finolex/prince waste pipe for wash basin or sink including brass check nut The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 112 | Providing and fixing 100 mm (one hundred millimetre) diametre ISI marked No 8934 of Jal/ ESS ESS C.P. Grating of clarion series of classik or contessa plus Jaquar / (Heavy duty makes ISI marked ) for gully / floor or Nahni trap including fitting in all respect The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 113 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. panincluding carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 114 | Providing and fixing flat back 600x450 (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass of Atul/Modi Gaurd mounted on 6mm (six Millimetre) thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brassscrews and washers etcetraetra complete. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 115 | Providing and fixing 600x120x5mm (six hundred into one hundred twenty into five millimetre) of Hindware/Cera glass shelf (Heavy duty makes ISI marked IS No. 8931 & 8934) with C.P. brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws etcetraetra complete. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 116 | Providing and fixing C.P.(chromium plated) brass towel rail ISI marked No 8934 of Jal/ ESS ESS having size 600x20 mm of clarion series of classik or contessa plus Jaquar of approved quantitycomplete withC.P. brass brackets fixed to wooden plugs with C.P. brass screws etcetraetra complete. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 117 | Providing and fixing chromium plated brass soap dish of ISI marked No 8934 of Jal/ ESS ESSC.P. brassbrackets fixedto wooden cleats with C.P. brass screws complete. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 118 | Providing and fixing C.P. brass long nose bib cock tap of ISI marked No 8934 of Jal/ ESS ESSsingle controlof approved quality conforming to IS standards. 15 mm (fifteen millimetre)nominal bore The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 119 | Providing and fixing 15 mm (fifteen millimetre)nominal bore CP brass stop cock ( concealed) of standred design and app. ISI marked No 8934 of Jal/ ESS ESS The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 120 | Providing and Fixing15 mm (fifteen millimetre)nominal bore CP brass Pillar cock tap ofISI marked No 8934 of Jal/ ESS ESS. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 121 | Providing and Fixing 15 mm (fifteen millimetre)nominal bore CP brasswash basin Mixer ofISI marked No 8934 of Jal/ ESS ESS. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 122 | Providing and fixing stainless steel kitchen sinksize 610 x 460 mm (six hundred ten into four hundred sixty millimetre) with bowl depth 200 mm (two hundred millimetre) of AMC / UNIK/ Diamondof ISI marked with drain board andC.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 123 | Providing and Fixing 15 mm (fifteen millimetre)nominal bore CP brassSink Mixer ofISI marked No 8934 of Jal/ ESS /Hindware/Cera/jaquar including necessary fitting complete in all respect. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 124 | Providing and fixing 15mm nominal bore PVC connection pipe of Supreme/finolex/prince with brass union 45cm (forty five centimetre) length, with necessary fittings. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 125 | Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 126 | Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, (eighty degree) including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 (one)metre spacing. This includes testing of joints complete 1620 (20 mm OD) pipe as per direction of the Engineer-incharge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 127 | 2025 (25 mm OD) pipe |
| 128 | Providing and fixing 20 mm (twenty millimetre) dia nominal bore G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 129 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m (one point five metre) in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m,(one point five metre) including getting out the excavated soil anddisposal of surplus excavated soil as directed, within a lead of 50 m.(fifty metre)The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 130 | Providing and layingcement concrete1:5:10 (1 cement : 5 coarse sand): 10 graded stone aggregate 40 mm nominal size) all roun sewerage pipe including led concrete as per standard design 150 mm (one hundred fifty millimetre) dia The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 131 | Providing and laying cement concrete 1:5:10 (One cement: five sand: ten graded crushed stone aggregate 40mm (Forty millimeter) nominal sizeup to haunches of 150 mm (one hundred fifty millimetre) dia sewerage pipe including lein concreteas per standard design The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 132 | Making conection of G.I. distribution branch with G.I. main of following size 25 (twenty five) to 40 mm (forty millimetre) nominal bore providing and fixing tee, including cutting and threading the pipe etctera complete.The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 133 | Providing and fixing high pressure PVC spigot of supreme / Finolex / Prince class "B" conforming to BS-13592 soil, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. completeincluding carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 134 | 75 mm (seventy five millimetre) Dia |
| 135 | 110 mm(one hundred ten millimetre)Dia |
| 136 | 150 mm (one hundred fifty millimetre) Dia |
| 137 | Providing and fixingPVC Single Equal Branch of Supreme / Finolex / Prince ISI marked with oval asses ISI Marked insertion rubber washer 3 mm (three millimetre) thick bolt and nuts complete i/c fixing with approved adhesive etc. Completeincluding carriage of material in all leads and lifts and other incidentalscomplete and as per the entire satisfaction and direction of Engineer-in-Charge. .The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 138 | 75 mm (seventy five millimetre) Dia |
| 139 | 110 mm (one hundred ten millimetre) Dia |
| 140 | Providing and fixing range of two stallvitreous China urinallarge Flat back No5001 of size 63.3x39.5x42 CM (sixty three decimal three into thirty nine decimal five into forty two cenetimetre) with automatic flushing cistern in White Shade ofHindware/ Cerawith fitting standard design C.P. brass flush pipe spreaders with union and clamps (all in C.P. brass) with waste fitting as per IS 2556 C.I. tap with outlet greating other coupling in C.P. brass including painting of fitting cutting holes & making good the same and carriage of materials within all leads and lifts The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 141 | Providing and fixing 600mmx300mm (six hundred into three hundred millimetre) vitreous china division plate of / Cera / Hindware/ jaquare/star white /snow white shade for urinals includings fittings complete as per approved specification drawings and entire satisfaction of Engineer-In-Charge.The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 142 | Providing and fixing 110 x 90 mm (One hundred ten into ninety millimeter) nominalsize/diameter P.V.C. floor trap of Supreme/ prince/ Finolex ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetra complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 143 | 110 x 75 mm(one hundred ten into seventy five millimetre) |
| 144 | Providing and fixing C.P. Grob bar of ISI marked of No 8934 of Jal/ESS ESSincluding carriage of material within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 145 | Providing and fixing P.V.C. collar of Supreme/prince/ Finolex including fixing with approved adhesive etcetraetra.complete The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 146 | 110mmnominal bore/diameter.(one hundred ten millimetre) |
| 147 | 75mm nominal bore/diameter (seventy five millimetre) |
| 148 | Providing and fixing P.V.C. ISI marked ofFinolex, Relpipe (reliance), Vectus Cowl including fixing ISI markedconfirming to ISI No-14735-99 including approved adhesive complete 75 mm (seventy five millimetre) dia The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 149 | Providing and fixing 32mm (thirty two millimetre) diameter CP brass chain/ rubber plug for sink or wash basin (Heavy duty ).The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 150 | Providing and fixing 32mm (thirty two millimetre)diameter C.P.Brass waste of ISI marked IS No. 8934 of Jal/ESS ESS waste pipe for wash basin or sink including brass check nut The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 151 | Providing and fixing C.P. Brass Toilet paper holder of clarion series of classik or contessa plus Jaquar (Heavy duty make ISI marked including fitting complete in all respect) The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 152 | Providing and fixing 15mm (fifteen millimetre) diameter nominal bore C.P.Brass push tap of ISI marked IS No.8934 of Jal/ESS ESS of approved quality conforming to IS 8931The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 153 | Providing and fixing 15mm(fifteen millimetre) diameter C.P. brass angle valve ofclarion series of classik or contessa plus Jaquar with nuts as per approved specifications drawing ,design and as directed by the Engineer-Incharge |
| 154 | Providing and fixing 15mm(fifteen millimetre) nominal bore brass full way valve with wheel of clarion series of classik or contessa plus Jaquar with necessary fitting including entire carriage of material with in all leads, lifts and other incidentals.The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 155 | Providing and fixing 15mm(fifteen millimetre) nominal bore brass valve (Horizontal plunger type) ofJal/Jaquar/high pressure with copper plate with necessary fitting including entire carriage of material with in all leads , liftsand other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 156 | Providing and fixing PVC double equal branch with oval access door, of Supreme/ Finolex/ Prince and insertion rubber washer 3mm (three millimetre) thick with bolts,nuts and ISI marked including fixing with approved adhesive etcetera complete as perH.P.P.W.D specification, approved drawing , design, as per the entire satisfaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government. |
| 157 | 150 mm (one hundred fifty millimetre) nominal bore/diametre |
| 158 | 110 mm (one hundred tenmillimetre) nominal bore/diametre |
| 159 | 75 mm (seventy five millimetre) nominal bore/diametre |
| 160 | Providing and fixing PVC door bend with oval access door, of Supreme/ Finolex/ Prince and insertion rubber washer 3mm (three millimetre) thick with bolts,nuts and ISI marked including fixing with approved adhesive etcetera complete as perH.P.P.W.D specification, approved drawing , design, as per the entire satisfaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government. |
| 161 | 150 mm (one hundred fifty millimetre) nominal bore/diametre |
| 162 | 110 mm (one hundred tenmillimetre) nominal bore/diametre |
| 163 | 75 mm (seventy five millimetre) nominal bore/diametre |
| 164 | Providing and fixing PVC holder bat clamps o fIS marked of finolex,Relpipe, Vectus approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm ten into ten intoten centimetre) of 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre ) nominal size) and cost of cutting holes and making good the walls etctera.including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 165 | 150 mm (one hundred fifty millimetre) nominal bore/diametre |
| 166 | 110 mm (one hundred tenmillimetre) nominal bore/diametre |
| 167 | 75 mm (seventy five millimetre) nominal bore/diametre |
| 168 | Providing and fixing PVC ISI marked of finolex,Relpipe, Vectus heal rest confirming to ISI No-14735-99 including filling the joints with approved adhesive complete. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 169 | 150 mm (one hundred fifty millimetre) nominal bore/diametre |
| 170 | 110 mm (one hundred tenmillimetre) nominal bore/diametre |
| 171 | Providing and fixing PVC offset 45 (forty five) ISI marked of finolex,Prince, Vectus including filling the joints with approved adhesive complete. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
| 172 | 150 mm (one hundred fifty millimetre) nominal bore/diametre |
| 173 | 110 mm (one hundred tenmillimetre) nominal bore/diametre |
| 174 | 75 mm (seventy five millimetre) nominal bore/diametre |
| 175 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm(forty millimetre) nominal size), inside plastering 12 mm ( twelve millimetre) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stoneaggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design :inside size 90x80 cm (ninety into eighty centimetre) and 45cm (forty centimetre) deep including C.I cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten millimetre) internal dimensions, total weight of cover and frame to be not less than 38kg (weight of cover 23 kg and weight of frame 15 kg) with sewer bricks conforming to IS: 4885 each 9650.15 The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 176 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm(twenty millimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm(twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design inside size 120x90 cm (one hundred twenty into ninety centimetre) and 90cm (ninety centimetre) deep including C.I cover with frame (midium duty) 500 mm internal diametre, total weight of cover and frame to be not less than 116kg (weight of cover 58 kg and weight of frame 58 kg) with sewer bricks conforming to IS: 4885 . The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 177 | Constructing of brick masonry chamber for underground C.I. inspection chamber and bends with common burnt clay building bricks in cement mortar 1:4 (1 cement : 4 sandC.I. cover with frame (light duty) 455x610mm (four hundred fifty five into six hundred ten millimeter) internal dimensions. Total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) weight of cover 23kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram). RCC top slab with 1:1.5:3(one cement : one point five coarse sand and : three graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:5:10 (1 cement :5 sand : 10 graded crushed /broken stone aggregate 40mm (forty millimeter) nominal size inside plastering 15mm (Fifteen millimeter) thick with cement mortar 1:3 (1 cement : 3 sand) finished with a floating coat of neat cement on walls and bed concrete etcetraetera complete inside dimensions 455x610 mm (Four hundred fifty five into six hundred ten millimeter) and 450mm (Four hundred fifty millimeter) deep for single pipe line completewith common burnt clay F.P.S. (non modular) bricks of class designation7.5 (seven point five) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana,toll tax, GST and all type of other taxes imposed by the Government. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
