Bharat Sanchar Nigam Limited-BSNL has published Tender For Construction Of 13 Buildings At Various Locations In India For Unified Network Management System Unms Including Finishing Works Water Supply And Sanitary Installations Electrical Installations And Cable Laying Automatic Fire Detection And. Submission Date for this Tender is 05-12-2023. Building Work Tenders in panchkula Haryana. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Supplying and placing in position FULKRUM High back Chair. The overall dimensions of the chair shall be: 1300 mm (H) X 700 mm (W) X 460 mm (D). The cushion headrest of the chair shall be adjustable for 5cm in height and for 40 degrees of tilt.Armrest of the chair shall be 4 way adjustable armrest, Height, Width, swivel angle and depth adjustable armrest for 6cm and swivel can be adjusted to 3 angular positions also available with height adjustability for 6cm and width adjustability for 5cm. The base of the chair shall be nylon base with 5 legs and dual wheel castors. The backrest of the chair shall be a breathable polyester mesh suspension which allows improved ventilation and transpiration, to provide exceptional thermal comfort. back frame is molded of resilient black polypropylene. The lumber pad of the chair shall be conveniently adjustable through side knobs, without getting up from the chair, to customize the exact support for various spinal shapes. backbone of the chair shall be made of die-cast aluminium in a luxurious polished finish or a glossy silver epoxy powder coating. The chair shall have synchronized mechanism with tilt- tension control, multi position tilt lock and pneumatic seat height control. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer in Charge. |
| 2 | Supplying and placing in position Fulkrum Mid back Chair. The overall dimensions of the chair shall be: 1080 mm (H) X 700 mm (W) X 460 mm (D). Armrest of the chair shall be 4 way adjustable armrest, Height, Width, swivel angle and depth adjustable armrest for 6cm and swivel can be adjusted to 3 angular positions. also available with height adjustability for 6cm and width adjustability for 5cm. The base of the chair shall be nylon base with 5 legs and dual wheel castors. The backrest of the chair shall be a breathable polyester mesh suspension which allows improved ventilation and transpiration, to provide exceptional thermal comfort. back frame is molded of resilient black polypropylene. The lumber pad of the chair shall be conveniently adjustable through side knobs, without getting up from the chair, to customize the exact support for various spinal shapes. backbone of the chair shall be made of die-cast aluminium in a luxurious polished finish or a glossy silver epoxy powder coating. The chair shall have synchronized mechanism with tilt- tension control, multi position tilt lock and pneumatic seat height control. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 3 | Supplying and placing in position Fulkrum LB YF low back Chair. The overall dimensions of the chair shall be: 1000 mm (H) X 700 mm (W) X 460 mm (D). Armrest of the chair shall be 4 way adjustable armrest, Height, Width, swivel angle and depth adjustable armrest for 6cm and swivel can be adjusted to 3 angular positions. also available with height adjustability for 6cm and width adjustability for 5cm. The base of the chair shall be nylon base with 5 legs and dual wheel castors. The backrest of the chair shall be a breathable polyester mesh suspension which allows improved ventilation and transpiration, to provide exceptional thermal comfort. back frame is molded of resilient black polypropylene. The lumber pad of the chair shall be conveniently adjustable through side knobs, without getting up from the chair, to customize the exact support for various spinal shapes. backbone of the chair shall be made of die-cast aluminium in a luxurious polished finish or a glossy silver epoxy powder coating. The chair shall have synchronized mechanism with tilt- tension control, multi position tilt lock and pneumatic seat height control.The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 4 | Supplying and placing in position Domino Sofa Set (SIX SEATER OCCUPANCY WITH CONNECTORS). The sofa set has to be modular systems with Linear and corner Modules. Each Modular shall be securely connected with Neighboring module using and integrated linking bracket which can be refastened by an Allen key. It shall be easily reconfigured at any place by just using Allen Keys. The coner module has to be supplied with 2 Nos. Right angled brackets, that doubles as an armrest on one side. Generous armrest width allows impromptu support for computer notebooks, drinks and Friends. |
| 5 | Each Modular of the sofa set has to be 750 mm wide and 750 mm broad with seat height to be 400 mm from ground giving healthy seating posture the back height shall be 320 mm from seat. The sofa Set has to be upholstered with Textile Fabric covering over polyurethane Foam. The Structure is a two way shell of Injection-molded polypropylene in black color, the Shell surface is adorned with patterns inspired by wood grains or Tree rings. Base feet is of injection molded black polypropylene are adjustable for height to compensate uneven floors. Linking brackets shall be made up of steel with black powder coating in a range of 60-80 microns.The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 6 | Supplying and placing in position 3 seater Domino Sofa Set. The sofa set has to be modular systems with Linear and corner Modules. Each Modular shall be securely connected with Neigbouring module using and integrated linking bracket which can be refastened by an allen key. It shall be easily reconfigured at any place by just using Allen Keys. The coner module has to be supplied with 2 Nos. Right angled brackets, that doubles as an armrest on one side. Generous armrest width allows impromptu support for computer notebooks, drinks and Friends. Each Modular of the sofa set has to be 750 mm wide and 750 mm broad with seat height to be 400 mm from ground giving healthy seating posture the back height shall be 320 mm from seat. The sofa Set has to be upholstered with Textile Fabric covering over polyurethane Foam. |
| 7 | The Structure is a two way shell of Injection-moulded polypropelene in black color, the Shell surface is adorned with patterns inspired by wood grains or Tree rings. Base feet is of injection moulded black polypropelene are adjustable for height to compensate uneven floors. Linking brackets shall be made up of steel with black powder coating in a range of 60-80 microns.The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 8 | Supplying and placing in position Café Table. The Table top shall be made up of 25mm thick E1 Grade Pre Laminated Particle Board with 2 mm thick PVC Edge Banding. The table top shall be fixed with legs through MS powder coated beams, with powder coating of a range of 60-80 microns. The Legs of the table shall be made up of Aluminium legs connected together with Die-Casted Connectors. The Table shall be provided with 2 Nos. beams for more stability and strength. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 9 | Supplying and placing in position Cafeteria Chair (Without Arms). The overall dimensions of the chair shall be 490mm (W) X 550mm (D) X 810mm (H). The shell of the chair shall be made up of molded polypropylene.Legs should be made up of 19mm tubular steel finished in silver proxy finish. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 10 | Supplying and placing in position Lecture Room Table of size: 1200 mm (L) X 750 mm (W) X 750 mm (H) MASA Foldable table with Modesty Panel. The Table top shall be made up of 25mm thick melamine wooden top and 50mm x 25mm Aluminium die cast legs with Table top foldable mechanism and lockable castors with MS powder coated embossed modesty of 450H. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 11 | Supplying and placing in position SINGLE SEATER SOFA with Leatherette upholstery of size 86cm X 90.5cm X 85.5cm. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 12 | Supplying and placing in positionKing Size Bed of of size 1905 x 2060 x 1008, made up of Sheesham wood all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 13 | Supplying and placing in positionmattress for double bed of size 78"L x 72"W x 4" Thick . The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 14 | Supplying and placing in positionBedside Table of size 450 x 400 x 450, made up of Sheesham wood all complete as per as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 15 | Supplying and placing in position Centre Table, (Cappuchino Colour) of size 1199 X 378 X 599 mmwith Solid MDF table top 18mm thick and legs of Solid rubber wood. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 16 | Supplying and placing in position3-doorwooden wardrobeof size (140cm x 59cm x 194.1cm) with 8 Shelves. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 17 | Supplying and placing in position Metallic single Bed of size 78"L x 36" W with slatted mattress base with headboard, mosquito net Rod & Metal sheet basket made up of Tubular steel sections, powder coated matt taupe white color. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 18 | Supplying and placing in positionmattress for single bed of size 78"L x 36"W x 100 mm Thick . The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 19 | Supplying and placing in position wooden corner table of size 53cm X 45cm X 45.8cm height of MDF top and rubber wood understructure with tapered legs in Cappuccino shade.The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 20 | Supplying and installation in position push / pull type Metallic Optimizers / Mobile storage system having 1 static unit model Optz SS1 1200mm and 1 Locking unit model Optz SL1 1200mmof size1980H X 1200W X 400D, and 3 twin/back to back units model Optz TM1 1200mm of size 1980H X 1200W X 800D, with Ergonomically designed C shaped Handles and centralised locking system with 100% VOC free powder coating , wheel drive andthe rails of 4metre length shall be chemically grouted in the floor for right allignment. The work shall be carried out all complete as per Architect Drawing No CA-4423 R18, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
| 21 | SH: MODULAR PARTITIONS AND WORK STATIONS |
| 22 | FULL HEIGHT MODULAR PARTITIONS (Without Door). The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19, WD-36-3135 R7, WD-37-3136 R6 & WD-39-3138 R6 and as per the directions of Engineer-in-Charge. |
| 23 | Supplying and installationFull Height partition of minimum 75mm thickness and should have clear space of 45-55 mm for electrical wiring. The height of partitions shall be as per drg ( minimum of 2185 mm) . All metallic parts shall undergo a 7 stage anti rust treatment and shall be powder coated in suede finish to a thickness of minimum 45 microns. |
| 24 | Modular Partition - The modular partitions shall not be grouted in the floors.The modular partitions shall be an assembly of the following parts:- |
| 25 | Levellers - Each frame shall be provided with two 10mm leveling bolts which allow 15mm adjustment for floor unevenness.The levelers shall be concealed inside the skirting and shall be completely retracted inside the skirting in case of uniformly flat floors. |
| 26 | Wall start (Optional) - This is a joinery, which is used to fix partition with wall. The section is made of 75mm (W)X 75/50mm(D)CRCA Steel. This should have necessary slots for fixing and can take wire from wall to partition. |
| 27 | Frames shall form the basic support structure for all components and shall be of 75mm x 35mm aluminium sections. The main vertical member of the frame bearing the load of brackets and storages shall be made of 1.2mm thick aluminium sections.The connecting vertical face shall be made up of 0.8-1mm thick aluminium sections. The horizontal members shall be made of 0.8mm aluminium extrusions. Each individual module shall not be more than 700mm in height and shall not be more than 1200mm in width.Frames can have 1-3 modules in prefabricated form.Additional height shall be achieved by mounting modules over them.The bottom module shall be mounted over askirting of more than 85mm height. The skirting shall be designed so that switches can be provided on the skirting level.The Base Beam (Skirting Inner Sections) shall be made of CRCA Steel. |
| 28 | The skirting shall be snap fitted on both sides with Skirting Plates made of 0.6mm thick aluminium extrusions.Wherever switches are provided on the skirting, the skirting plates shall have the necessary slots (Optional/As per Requirement). |
| 29 | Frame Gasket- Frame modules shall have PVC foam Gaskets of 4mm thickness and 10mm width pasted with PVA glue along the inner periphery on both sides to prevent sound and dust transmission through the tiles.The frames shall also have 2mm x 10mm foam gaskets pasted with PVA glue on the outer periphery so as to seal the gaps between the adjacent frames. |
| 30 | Ceiling Rail-The telescopic ceiling rails shall be made of CRCA Steel of 75mm Cross section with 0.7mm thickness.The height of the ceiling rail shall be of 50mm thick.The ceiling rail should allow an height adjustment of 10mm to 15mm upwards. |
| 31 | Posts-The frames shall be connected at the junctions by CRCA Steel connectors.The Junction of frames shall be snap fitted with square Posts.The Posts shall be made of CRCA Steel of1.6mm thickness of section 75mm x 75mm for 2-Way & 75mm x 15mm for 3-Way. |
| 32 | Trims-The exposed vertical and horizontal faces of the frames shall be snap fitted with curve trims. The trims shall be made of aluminium extrusions of 1mm thickness and 75mm width in a Curvature of 12mm. |
| 33 | Wire Management- |
| 34 | Slots shall be provided on Skirting / Tiles / Partition to fix all electrical & data points as per Requirement. |
| 35 | Tile Finish:- |
| 36 | 1st Modules in Steel Powder Coated Embossed finish, 2nd, 3rd Module in laminated Finish and 4th & 5th Modules in Plain Glass Finish for Front Door Side Partitions. |
| 37 | 1st Modules in Steel Powder Coated Embossed Finish, 2nd Module in Pinup / Marker / Laminated Finish,3rd Module in Laminated Finish, 4th & 5th in Plain Glass for Side / dividing partition. |
| 38 | LAMINATED TILES: Laminated tiles shall be made of 8-10mm MDF (Medium Density Fibre Board) with 0.6-0.8mm Post Lamination on both sides of the tile. |
| 39 | FABRIC TILES: The fabric tiles shall be made of 8-10mm MDF with fabric. It should be possible to replace the fabric by peeling it off. |
| 40 | MAGNETIC PINUP TILES: The Pinup tiles shall be made of 0.6mm Galvanised Iron (GI) sheet with fabric.It should be possible to replace the fabric by peeling it off. |
| 41 | Glass Tiles- Glass Tiles shall be 4 mm clear toughened glass are supplied and fixed from both side with all necessary interior trims and gaskets . There are two glass tiles that can be fitted and are completely interchangeable with regular tiles. |
| 42 | Plain Glass Door - Supplying and fixing of Glass Door with Shuttersin the full height partition made of 12mm thick Toughened Glass including locking arrangement, Handle with Floor Spring. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19, WD-36-3135 R6, WD-37-3136 R5 & WD-39-3138 R5 and as per the directions of Engineer-in- Charge. |
| 43 | Laminate Door - Laminate Door with Shutters in the full height partition made of 38mm thick Honey Comb with both side lamination with PVC lipping including locking arrangement, Handle with Door Closure, Stopper, Hinge. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19, WD-36-3135 R6, WD-37-3136 R5 & WD-39-3138 R5 and as per the directions of Engineer-in-Charge. |
| 44 | MODULARCABIN / CUBICAL WORKSTATION (WITH / WITHOUT PARTITION) - |
| 45 | Supplyingand fixing of Modular Workstations comprises of the followings as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19, WD-36-3135 R7, WD-37-3136 R6 & WD-39-3138 R6 all complete as per the directions of Engineer-in-Charge. |
| 46 | Low Height partition of minimum 75mm thickness and should have clear space of 45-55 mm for electrical wiring. The height of partition shall be 1660 mm. All metallic parts shall undergo a 7 stage anti rust treatment and shall be powder coated in suede finish to a thickness of minimum 45 microns. |
| 47 | Levellers - Each frame shall be provided with two 10mm leveling bolts which allow 15mm adjustment for floor unevenness.The levelers shall be concealed inside the skirting and shall be completely retracted inside the skirting in case of uniformly flat floors. |
| 48 | Frames shall form the basic support structure for all components and shall be of 75mm x 35mm aluminium sections. The main vertical member of the frame bearing the load of brackets and storages shall be made of 1.2mm thick aluminium sections.The connecting vertical face shall be made up of 0.8-1mm thick aluminium sections. The horizontal members shall be made of 0.8mm aluminium extrusions. Each individual module shall not be more than 700mm in height and shall not be more than 1200mm in width.Frames can have 1-3 modules in prefabricated form.Additional height shall be achieved by mounting modules over them. The bottom module shall be mounted over askirting of more than 85mm height. The skirting shall be designed so that switches can be provided on the skirting level.The Base Beam (Skirting Inner Sections) shall be made of CRCA Steel. |
| 49 | Posts - The frames shall be connected at the junctions by CRCA Steel connectors.The Junction of frames shall be snap fitted with square Posts.The Posts shall be made of CRCA Steel of1.6mm thickness of section 75mm x 75mm for 2-Way & 75mm x 15mm for 3-Way. |
| 50 | Trims - The exposed vertical and horizontal faces of the frames shall be snap fitted with curve trims. The trims shall be made of aluminium extrusions of 1mm thickness and 75mm width in a Curvature of 12mm. |
| 51 | Slots shall be provided on Skirting / Tiles / Partition to fix all electrical & data points as per Requirement. |
| 52 | 1st Modules in Steel Powder Coated Embossed finish and 2nd Modules in Fabric / Pinup / Marker Finish. |
| 53 | LAMINATED TILES: Laminated tiles shall be made of 8-10mm MDF (Medium Density Fibre Board) with 0.6-0.8mm Post Lamination on both sides of the tile. |
| 54 | FABRIC TILES: The fabric tiles shall be made of 8-10mm MDF with fabric. It should be possible to replace the fabric by peeling it off. |
| 55 | MAGNETIC PINUP TILES: The Pinup tiles shall be made of 0.6mm Galvanised Iron (GI) sheet with fabric.It should be possible to replace the fabric by peeling it off. |
| 56 | Table ofsize as specified below. Worktop made of 25mm thick pre-laminated particle board of approved shade. The working and non – working edges shall be provided with hotpressed 0.8-1.2mm thick PVC (Poly Vinyle Chloride) edging using special hot melt glue at high temperature. Table Top Understructure consists of CRCA Steel Powder Coated Brackets, 18mm thick Prelam Modesty Panels, 25mm thick Prelam Gable Ends and by CRCA Steel Powder Coated Legs. |
| 57 | STRAIGHT WS SIZE-1200mm x 600mm for Each User (Without Partition) |
| 58 | STRAIGHT WS SIZE-900/1050mm x 600mm for Each User (Without Partition) |
| 59 | STRAIGHT WS SIZE-1200mm x 600mm for Each User. (MOUNTED ON 75mm Thick Element FRAME-1660 H, With Electrical Provision) (With One Pinup for Each User) |
| 60 | STRAIGHT WS SIZE-900/1050mm x 600mm for Each User.(MOUNTED ON 75mm Thick Element FRAME-1660 H,With Electrical Provision) (With One Pinup for Each User) |
| 61 | Main Table of size 1800mm x 750mm x 730mmH with Return Table of 1500mm x 450mm x 730mmH (Without Partition) |
| 62 | Main Table of size 1800mm x 750mm x 730mmH with Return Table of 1500mm x 450mm x 730mmH. (MOUNTED ON 75mm Thick Element FRAME-1660 H, With Electrical Provision) (With One Pinup, One Marker for Each User) |
| 63 | STRAIGHT WS SIZE-1050/1200mm x 600mm for Each User. (MOUNTED ON 75mm Thick Element FRAME-1660 H,With Electrical Provision) (With One Pinup for Each User) (With Divider 75mm Thick & 1660 H Partition) |
| 64 | CUBICLE WS EACH SIZE-Main Table of size 1800mm x 750mm x 730mmH with Return Table of 1200mm x 450mm x 730mmH (Without Partition) |
| 65 | STRAIGHT WS SIZE-550/600mm x 600mm for Each User. (MOUNTED ON 75mm Thick Element FRAME-1660 H, With Electrical Provision) (With One Pinup for Each User) (With Divider 75mm Thick & 1660 H Partition) |
| 66 | STRAIGHT WS SIZE-900/1050mm x 600mm for Each User. (MOUNTED ON 75mm Thick Element FRAME-1660 H,With Electrical Provision) (With One Pinup for Each User) |
| 67 | Providing / Supplying & installing Over Head Hampers made of CRCA Steel with Powder Coating with Slide up Doors / Hinge Shutters. The inside Bin is provided with 2 Nos. of Divider Flaps with locking arrangement complete, to be mounted over Element Partitions & Wall Frames only. The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19, WD-36-3135 R7, WD-37-3136 R6 & WD-39-3138 R6 and as per the directions of Engineer-in- Charge. |
| 68 | SIZE-600 /750 / 900mm (L) x 300mm(D) x 450mm(H) |
| 69 | SIZE-1050 / 1200mm(L) x 300mm(D) x 450mm(H) |
| 70 | ACCESSORIES as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19, WD-36-3135 R7, WD-37-3136 R6 & WD-39-3138 R6 all complete as per the directions of Engineer-in-Charge. |
| 71 | Keyboard pull out trayofmade of0.8mm thick CRCA steel duly powder coated, of minimum thickness 45micron, with metallic roller slides on both sides on Telescopic mechanism and shall be fixed to the bottom of worktop surface with the help of screws. |
| 72 | Three 3-drawer unit shall be of size 455mm (L) x 560mm (D) x 680(H) on levellors made of 0.8-2mm thick CRCA body andfascia duly powder coated of minimum thickness 45micron. The drawer unit shall consist of two drawers and one filing box mounted on roller slides on both sides. It shall be provided with central lock mechanism with keys and flush handles are to be providedin front to facilitate opening and closing of drawers. |
| 73 | Three 3-drawer unit shall be of size 455mm (L) x 560mm (D) x 680(H) on levellors made of 0.8-2mm thick CRCA body andfascia duly powder coated of minimum thickness 45micron. The drawer unit shall consist of two drawers and one filing box mounted on roller slides on both sides. It shall be provided with central lock mechanism with keys and flush handles are to be providedin front to facilitate opening and closing of drawers. Drawers shall be provided with Top supporting brackets made of CRCA steel duly powder coated. |
| 74 | Three 3-drawer unit shall be of size 390mm (L) x 450mm (D) x 680(H) on levellors made of 0.8-2mm thick CRCA body andfascia duly powder coated of minimum thickness 45micron. The drawer unit shall consist of two drawers and one filing box mounted on roller slides on both sides. It shall be provided with central lock mechanism with keys and flush handles are to be providedin front to facilitate opening and closing of drawers. |
| 75 | Supplying and placing PINACLE Table worktop made of 25mm thick Particle Board with Pre laminated finish with 2mm thick PVC lipping of matching shade. |
| 76 | Understructure: 18mm thick Modesty panel and 25mm thick Gable ends with Pre laminated Particle Board finish with 2mm thick PVC Lipping of matching shade. |
| 77 | Main Table of Size:2100mmx800/850mm with side unit of size:1200mmx450mmx750mm (H) with Storage underneath made of 18mm thick PLPB with 2mm thick PVC lipping of matching shade. |
| 78 | Back unit of size: 1500mm x 450mm x 750mm(H) with Storage 750mm (L) underneath made of 18mm thick PLPB with 2mm thick PVC lipping of matching shade. |
| 79 | The work shall be carried out all complete as per Architect Drawing No CA-4423 R20, CA-4424 R19, CA-4425 R19 and as per the directions of Engineer-in-Charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
