Tender For Additions/ Alteration And Renovation To Building No. P-120, P-122 And P-177 (Dlomi) At Drdo Township, Kanchanbagh, Hyderabad., Hyderabad-Telangana

TDR : 40784633

Tender Notice
BOQ

Expired

Hyderabad , Telangana

Tender Brief : Tender For Additions/ Alteration And Renovation To Building No. P-120, P-122 And P-177 (Dlomi) At Drdo Township, Kanchanbagh, Hyderabad.

Document Fees
Refer document

EMD
₹ 688700.0 /-

Tender Value
Refer document

Submission Date
14-12-2023

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Sub Head-I Site Clearance & Earth Work Excavation.
2	Removing Trunks of Trees (at Ground Level and Below) by Cutting and removing the roots and disposal of unserviceable material outside Ministry of Defence (MoD) Land.(a) Beyond 120 cm girth upto and including 240cm girth
3	Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.
4	All Kinds of Soil
5	Ordinary rock
6	Filling with available earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge.
7	Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond Ministry of Defence(MoD) Land, for all leads including all lifts involved.
8	SubHead-IIPlain & Reinforced Cement Concrete Work.
9	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
10	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
11	1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
12	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :(a) 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources).
13	Reinforced cement concrete work for pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :(a) 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
14	Centering and shuttering including strutting, propping etc. and removal of form fora) Lintels, beams, plinth beams, girders, bressumers and cantilevers
15	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.(a) Thermo-Mechanically Treated bars of grade Fe-500D or more.
16	SubHead-III Stone & Brick Work.
17	Random rubble masonry with hard stone in foundation and plinth including levelling up withcement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :(a) Cement mortar 1:6 (1 cement : 6 coarse sand)
18	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :(a) Cement mortar 1:6 (1 cement : 6 coarse sand)
19	Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.(a) Cement mortar 1:4 (1 cement :4 coarse sand)
20	SubHead-IV Finishing
21	12mm thick plastering in cement motor 1:6 ( 1cement : 6 fine sand ) on internal surfaces of walls finished smooth and even etc., complete at all levels and locations
22	15 mm thick cement plaster on the rough side of single or half brick wall of mix: (a) 1:4 (1 cement : 4 fine sand)
23	18mm thick cement plastering on external surfaces of brick concrte surfaces in two layers consisting of 6mm thick cement motor 1:3( 1 cement : 3 fine sand ) top coat mixed with integralwater proofing compound as per manufacturers instructions over a base coat 12mm thick cement motar 1:5 ( 1 cement : 5 coarse sand ), finished sand face ete., complete at all levels and locations.
24	Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification.On New Work (two or more coats)
25	Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade :On Old Work (two or more coats)
26	Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete
27	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade
28	Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm)over existing cement paint surface
29	Old work (one or more coats applied @ 0.83 ltr/10 sqm).
30	Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.(a) New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.
31	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
32	Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. (a) With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre
33	Wall painting with premium acrylic emulsion paint of interior grade,having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. (Internal finishing side)(a) Two coats
34	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. (Steel and Wood surfaces)
35	Painting with synthetic enamel paint of approved brand andmanufacture of required colour to give an even shade :One or more coats on old work. (Steel and Wood surfaces)
36	SubHead- V Flooring
37	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
38	(a) Double Charge polished Finish Size of Tile 600 x 600 mm
39	(b) Double Charge polished Finish Size Size of Tile 800 x 800 mm
40	Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. Complete.
41	(a) Size of Tile 600x600 mm
42	(b) Size of Tile 800x800 mm
43	Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.
44	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
45	Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :(a) Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
46	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen/WHB platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.(a) Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm
47	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :(a) 20 to 25 mm thick
48	62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.
49	Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard,steps risers and threads jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).(a) Dark shade pigment using ordinary cement
50	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.(a) Granite work
51	SubHead- VI Wood, Steel, Aluminium, UPVC & Glass Works.
52	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).(a) Kiln seasoned and chemically treated hollock wood
53	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.(a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
54	Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:(a) Profile B, fixing with adjustable lugs with split end tail to each jamb
55	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)(a) Second Class teak wood :35 mm thick shutters
56	Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.(a) Second Class teak wood : 35 mm thick
57	Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) 2.5 Track–2 Panel Sliding windows with mesh duly manufactured using UPVC reinforced profiles of 88 mm x 52 mm x 2.20 mm for outer frames, 60 mm x 42 mm x 2.2mm for sliding shutter frames capable of mounting single glazing system, structurally reinforced with 32 mm x 16 mm x 1.2 mm with hot dip galvanized up to 120 GSM of minimum thickness of 1.2 mm for Outer frame/1.5 mm for Sash and the shutter of fly screen with SS-304 mesh shall be made of size 22mm x 52mm extruded UPVC window profile section of white colour having outer wall thickness of 2.2mm (± 0.3mm) provided with reinforcement of minimum 1.5mm thick G/J/U/S/O type GI section duly mitered cut and thermal welded at all corners and prefabricated & welded through fusion welding. The window sash shall be fitted with 5 mm thick clear float glass of reputed make duly fixed with EPDM Gasket for sash. System shall have single point locking with Touch Lock zamak alloy and the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/ deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work.
58	Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) Casement windows Openable shutters duly manufactured using UPVC reinforced profiles (Composition of profile shall consists a minimum of 6 PHR of TiO2 and not more than 10 PHR of CaCo3 for every 100 parts of PVC resin) of 60 mm x 58 mm x 2.20 mm for outer frames, 60 mm x 72 mm x 2.20 mm for mullion sections for two or more Openable shutters 60 mm x 78 mm x 2.20 mm for Openable shutter frame capable of mounting single glazing system structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.2 mm FOR Outer frame & 1.5 mm for Sash prefabricated & welded through fusion welding. The window sash shall be fitted with 5 mm thick clear float glass of reputed make duly fixed with EPDM Gasket for sash and accessories for casement window – friction hinges of stainless steel grade 304/430- 2 Nos., per sash, handle with zamak alloy casting 1 No. per sash, multipoint locking system suitably concealed 1 No., per sash provided with raiser wedges for smooth operation and the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/ deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work.
59	Providing, supplying & fixing of Fixed Louvered Ventilator made out of multi chambered UPVC sections with Glazing bead with EPDM black gasket. Having isolated drainage and reinforced with Galvanized Iron profiles throughout the window. The outer frame having an overall size of (60 mm x 36 mm x 2.2 mm)/(60 mm x 58 mm x 2.2 mm) with reinforcement of 1.2 mm thickness and Mullion with overall size of (60 mm x 36 mm x 2.2 mm)/(72 mm x 60 mm x 2.20 mm) with reinforcement of 1 mm thickness. (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin).Ventilator shall be provided with 4 mm Pin Head glass, standard hardware and Exhaust Fan provision will be fixed with Mdf board. Wall thickness of frame & Mullion shall be 2.2 mm. including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work.
60	Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) 2 Track–2 Panel Sliding windows duly manufactured using UPVC reinforced profiles(Composition of profile shall consists a minimum of 6PHR of TiO2 and not more than 10 PHR of CaCo3 for every 100 parts of PVC resin) of 60 mm x 52 mm x 2.2 mm for outer frames, 60 mm x 42 mm x 2.20 mm for sliding shutter frames capable of mounting single glazing system, structurally reinforced with hot dip galvanized up to 120 GSM of minimum thickness of 1.2 mm for Outer frame & 1.5 mm for Sash mm prefabricated & welded through fusion welding. The window sash shall be fitted with 5 mm thick clear float glass of reputed make duly fixed with EPDM Gasket for sash. System shall have single point locking with Touch LockZamak alloy and the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/ deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work.
61	Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) Casement Mesh windows Openable shutters duly manufactured using UPVC reinforced profiles (Composition of profile shall consists a minimum of 6 PHR of TiO2 and not more than 10 PHR of CaCo3 for every 100 parts of PVC resin) of 60 mm x 58 mm x 2.20 mm for outer frames, 60 mm x 72 mm x 2.20 mm for mullion sections for two or more Openable shutters 60 mm x 78 mm x 2.20 mm for Openable shutter frame capable of mounting single stainless steel grade 304 wire guage with wire of dia 0.5mm and average width of aperture 1.4mm structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.2 mm FOR Outer frame & 1.5 mm for Sash prefabricated & welded through fusion welding. The window sash shall be fitted with stainless steel grade 304 wire guage of dia 0.5 mm and average width of aperture 1.4 mm in both directionsand accessories for casement window – friction hinges of stainless steel grade 304/430- 2 Nos., per sash, handle with zamak alloy casting 1 No. per sash, multipoint locking system suitably concealed 1 No., per sash provided with raiser wedges for smooth operation and the system is to be installed at the site using anchor fasteners, silicon rubber sealant at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work.
62	Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws :30 mm thick shuttersSecond class teak wood
63	Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.
64	Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC \"C\" channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the \"C\" Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer\"s specification &drawing.
65	30 mm thick plain PVC door shutters
66	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately) :
67	a) For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)
68	b) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)
69	Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge
70	Providing and fixing ISI markedIS: 1341 M.S. pressed butt hinges bright finished with necessary screws etc. complete : 100x58x1.90 mm
71	Providing and fixingISI marked oxidised M.S. double acting spring hinges with necessary screws including welding as required etc. complete. (Copper Oxidized as per IS:1378) 125mm
72	Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm
73	Providing and fixing bright finished brass handles with screws etc. complete: 125 mm
74	Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete: (a) 300x16 mm
75	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. Complete.(a) Twin rubber stopper each
76	Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
77	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.(a) Fixed to openings /wooden frames with rawl plugs screws etc
78	Providing and fixing bright finished brass handles with screws etc. complete: 100 mm
79	Providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete : 115 mm
80	Providing and fixing 18mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge (Note: Fittings to be paid separately).(a) 18 mm thick
81	Providing and fixing in wall lining flat pressed three layer (medium density) Plywood Shutter for wardrobes etc withPre-laminated one side decorative lamination and other side balancing lamination thickness minimum 1mm Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement and required screws, hinges , handles,magnets etc. complete as directed by engineering in charge: (a) 18 mm thick
82	Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. Complete :(a) 50 x 20 mm
83	Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.(a) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
84	Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:(a) Float glass panes of nominal thickness 5mm (weight not less than 10kg/sqm)
85	Sub Head- VII Roofing Works
86	Taking down existing roof treatment of any position with bituminious felt including plaster/ loose concrete and removing rubbish and roughing the surface of old concrete by picking scrapping, cleaning and washing down with water to remove all dust etc. all as specified and directed.
87	Providing padding Concrete for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size)
88	6 mm thick cement plaster of mix : 1:4 (1 cement: 4 fine sand)
89	Terrace Water Proofing System (a) Corner Treatment Coving : Preparing the coving at the junction of slab and vertical offsets with CM 1:3 admixed with Nitobond SBR Latex at the dosage of 3L/bag of cemebt under(b) Surface Preparation : Preparing the surface by Mechanical means like grinding and cleaning the surface with water or wire brush whichever is suitable according to the site condition(c) Cracks Treatment : Chasing the cracks and cut open the same in V Groove and cleaning the same with Air blower and with water then it shall fill with Nitoseal PU 50 Sealant / Conbextra GP2 / Conbextra EP 10 Low viscous grout as per the substrate condition along with Cementitious Injection Grouting(d) Injection Grouting (If required) : Pressure grouting shall be done with Cebex 100, plasticizing expandable cementitous grout admixture. The material shall be injected using 40 PSI Injection grout pump with cement slurry mixed Cebex 100 at 225gms per 50kg bag of cement
90	(e) Bore Packing / Pipe Outlets : Preparing the inside surface of core and PVC by roughening using suitable file to get better adhension prior to packing works. Providing necessary formwark for packing the bore using suitable arrangement (depending upon site conditions). Packing the gap using non-shrink cement polymer-based grout using Conbextra GP2 upto surface of hte bore whilst the Nitobond SBR is in tacky state. The above analysis is based on assumption for 150mm diameter core with 110mm diameter PVC for 5\" thick slab only(f) Water Proofing System : Providing and applying two coats of brush bond RFX, a High Performance acrylic polymer modified Cementious waterproof coating, shall contain a liquid polymer component and a Cementitous powder component, which shall be mixed as per manufacturer\"s instructions and applied over prepared concrete surface strictly maintaining the coverage specified by the manufacturer. The applied material of Brush bond RFX shall have 1.0mm thickness of cured coating membrance shall exhibit properties of static crack accommodation of 1mm according to ASTM -C836 terminating the coating at 200mm above FFL.
91	(g) Protective Screed : The waterproof coated surface shall be protected with a 50mm thick to 75mm thick screeds with grade as per the design requirement, maintaining a slope of 1 in 100. The screed that shall be laid is admixed with Conplast WL Xtra an integral waterproofing admixture @ dosage of 200mgs per 50 kg cement. The curing shall be done as for a minimum of 7 days Note:- The work to be Executed through authorised applicator of manufacture only as per specification. Work completed to be Guaranted for 05(Five) Years as per the conditions of contract.
92	Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately).(a) 0.56mm Aluminium color profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm.
93	Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete :(a) Precoated/mill finish aluminium Ridges plain (500- 600mm)
94	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Hot finished Seamless type tubes
95	Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.(a) M.S. tube
96	Supplying and Fixing Acrlic Frosted fiber sheet 10mm thick of approved make Fixed to mild steel tubular structure with MS Screws etc.,
97	FALSE CEILINGProviding and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish
98	of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction ofthe Engineer in Charge but excluding the cost of painting with :(a) 12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3):1996 (Boards with BIS certification marks)
99	Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. Including:(a) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.
100	(b) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.
101	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
102	Sub Head- VIII Hard Standing & External Works
103	Demolishing cement concrete manually/ by mechanical means including disposal of material within a lead of 50 metres as per direction of Engineer - in – charge.(a) Nominal concrete 1:3:6 or leaner mix (i/c equivalent design mix)
104	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(a) 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
105	Providing and laying in position cement concrete of specified grade in hard standing etc laid in panels including the cost of formwork and finishing smooth - All work up to plinth level :(a) 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
106	Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.(a) 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.
107	Sub Head -IX Internal Water Supply & Sanitary Services
108	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including fittings and brackets, cutting and making good the walls wherever required:(a) White Vitreous China Flat back wash basin size 550x 400 mm
109	Providing and fixing Vitreous China oval type wash basin counter top with 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including fittings and cutting and making good the walls wherever required:
110	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :(a) W.C. pan with ISI marked white solid plastic seat and lid
111	Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:(a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
112	Providing and fixing white vitreous china flat back Single half stall urinal of size 580x380x350 mm with 15mm CP stop cock, PVC connection pipe and fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, with outlet grating and other couplings in C.P. brass, including cutting and making good the walls and floors wherever required :
113	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board(a) 510x1040 mm bowl depth 250 mm
114	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.
115	(a) Concealed work, including cutting chases and making good the walls etc.(i) 15 mm dia nominal bore
116	(ii) 20 mm dia nominal bore
117	(b) Exposed on wall (i) 25 mm nominal dia Pipes
118	Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
119	(a) 1000 Ltr capacity
120	(b) 500 Ltr capacity
121	Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.(a) 20 mm nominal bore, 120 mm long, weighing not less than 198 gms
122	Providing and fixing CPVC gate valve with handle of approved quality (screwed end) : 20 mm nominal bore
123	Providing and fixing in position best quality CP towel rod of Jaquar CAT NO. ACN-CHR-1111SM or approved make and length 600mm long with a pair of brackets flanges fixed to wall with necessary plugs screws , washers etc., complete.
124	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (a) 15mm nominal bore
125	Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.(a) 15 mm nominal bore with 30cm length
126	Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.(a) 15 mm nominal bore with 45 cm length
127	Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.(a) 15 mm nominal bore
128	Supply and Fixing two way CP brass bib cock 15mm bore complete .
129	Supply and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.(a) 15 mm nominal dia
130	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
131	Providing and fixing mirror of 5mm thick for wash basin etc. with superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
132	Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
133	Providing and fixing toilet paper holder : C.P. brass
134	Providing and fixing PTMT grating of approved quality and colour. Circular type(a) 125 mm nominal dia with 25 mm waste hole
135	Supply and fixing of 1.20 mts long easy flex tube with end nuts and hook and Health Faucet all complete. Hook to be fixed with CP brass with suitable counter sunk screws, all of approved make etc., complete Health Faucet (ABS Body) with 1m long easy flex tube in chromo finish and wall hooks Model No. ALD-573 of M/s Jaquar make or equivalent
136	Providing and Fixing CP Brass Shower Rose with 15 or 20mm inlet (a) 100mm dia (Model No. OHS-1989 of M/s Jaquar Make )
137	Providing and fixing PVC (SWR) Pipes single socketed, in any length with rubber ring joints layed in trenches or in floors for waste and vent pipes :
138	(a) 110 mm diaPVC (SWR) Pipes
139	(b) 75 mm diaPVC (SWR) Pipes
140	Providing and fixing PVC (SWR) Pipes single socketed, in any length and at any heights with rubber ring joints to fixed walls waste and vent pipes :
141	(a) 110 mm diaPVC (SWR) Pipes
142	(b) 75 mm diaPVC (SWR) Pipes
143	Providing and fixing PVC (SWR) Bends of any radius
144	(a) 110 mm diaPVC (SWR) Pipes
145	(b) 75 mm diaPVC (SWR) Pipes
146	Providing and fixing PVC (SWR) Branch Piece single equal or un equal.
147	(a) 110 mm diaPVC (SWR) Pipes
148	(b) 75 mm diaPVC (SWR) Pipes
149	Providing and fixing PVC (SWR) Junction (single-T) equal or un equal and with access door as directed by engineer in charge.
150	(a) 110 mm diaPVC (SWR) Pipes
151	(b) 75 mm diaPVC (SWR) Pipes
152	Providing and fixing PVC (SWR) Vent Covers
153	(a) 110 mm diaPVC (SWR) Pipes
154	(b) 75 mm diaPVC (SWR) Pipes
155	Providing and fixing Chlorinated Polyvinyl Chloride (UPVC) pipes, having thermal stability for hot & cold water supply including all UPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.(a) External work, 50 mm nominal dia Pipes
156	Providing and fixing Nahani trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :(a) 100 mm inlet and 100 mm outlet of PVC
157	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.7 kg as per standard design:(a) 100x100 mm size P type(i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
158	Sub Head- X Miscellaneous Works
159	Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete : 20 mm dia
160	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc.complete and stacking within 50 metres lead :(a) Of area 3 sq. metres and below
161	Taking out doors, windows and clerestory window shutters (steel or wood) including cutting steel window shutters using gas cutter and stacking within 50 metres lead : (a) Of area 3 sq. metres and below
162	Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.(a) In cement mortar
163	Demolishing R.C.C. work manually/ by mechanical means includingstacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.(a) In cement mortar
164	Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge :(a) In cement mortar
165	Demolishing RCC Jally up to 100mm thick manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge.
166	Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead
167	Dismantling tile work in floors laid in cement mortar including stacking material within 50 metres lead.(a) For thickness of tiles 6 mm to 20 mm
168	Dismantling aluminium/ Gypsum partitions, fixed glazing, false ceiling, ACP Cladding etc including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.
169	Dismantling wooden boardings in lining of walls,cupboards and partitions, excluding supporting members but including stacking within 50 metres lead :(a) Thickness above 10 mm up to 25 mm
170	Dismantling steel work in built up sections in angles, tees, flats, steel gates and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.
171	Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in- Charge.(a) Internal Work- Concealed on wall
172	Dismantling C.I. soil pipes or PVC rain water pipe with fittings and clamps including stacking the material within 50 metres lead :
173	(a) 75 to 80 mm dia pipe
174	(b) 100 mm dia pipe
175	Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge.
176	Dismantling of wash basins with pillar cock, waste coupling, PVC connection pipe, stop cock etc
177	Dismantling of PVC Flusing cistern with PVC connection pipes, stop cock etc
178	Taking down of bib taps, stop cocks, angle cocksetc.,
179	Taking down of Wash basin mixer and wall mixer etc.,
180	Dismantling of Aluminium composite panel, Aluminium fixed glazing, Aluminium doors and windows etc
181	Dismantling of 18mm thick particle board/ plywood cupboard shutters, shelves etc
182	Supply & Fixing brass cutting letters of size 300mm high and 25mm wall thickness , appolex laquer coated including soldering with lead , buffing and colouring with standard color ISI standard , MRF brand fixed on existing ACP./any type of wall surfaces with brass and nuts complete all as directed by Engineer -in - Charge
183	Dismantling old plaster or skirting raking out joints and cleaning the surface including disposal of rubbish
184	CREDIT FOR FOLLOWING RETRIEVED ITEMS:-
185	Wash basins with Brackets PVC connection Pipes, Pillar Cock, Waste Coupling etc against item no. 141.00
186	Flusing cisterns with PVC connection Pipes, stop cock etc against item no. 142.00
187	Sanitary CP Fitting such as Taps, Bib Cocks, Piller Cocks, Stop Cocks and Angle Cocksetc against item no. 143.00
188	Sanitary CP Fitting such as Basin Mixers and wall Mixers etc against item no. 144.00.
189	GI Pipes of following dia against item no. 138.00 :-
190	(a) 15mm
191	(b) 20mm
192	(c) 25mm
193	Soil C.I Pipe
194	(a) 75mm against item no. 139.01
195	(b) 100mm against item no. 139.02
196	PVC Storage Water tanks
197	(a) 500 Liters against item no. 140.00
198	(b) 1000 Liters against item no. 140.00
199	Doors, Windows etc including chowkats against item no. 127.00
200	Door and Window shutters against item no. 128.00
201	MS items like Gates, railings against item no. 137.00
202	Aluminium items like railing, windows, ACP etc against item no. 127.00 & 145.00
203	Wood items like cubboard shutters, Shelves etc against item no. 146.00
204	Sub Head - XI External Sewage Disposal
205	Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :(a) Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia
206	Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre).
207	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :
208	(a) 150 mm diameter S.W. pipe
209	(b) 200 mm diameter S.W. pipe
210	Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :
211	150 mm diameter
212	200 mm diameter
213	Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :
214	(a) Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :(i)With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
215	(b) Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : (i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
216	Extra for depth for manholes
217	(a) Size 90x80 cm(i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
218	(b) Size 120x90 cm(i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
219	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe
220	Cutting road and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required.
221	(a) bituminous portion
222	(b) Water bound macadam
223	Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond Ministry of DefenceLand, for all leads including all lifts involved.
224	Sub Head -XII Internal Electrical Works
225	Taking down carefully any type of point wiring light fans socket or power complete fitting such as swith ceiling roses, pendent, regulator, sockets etc removing material and making good disturb surface of wall floor etc complete
226	Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 Sq.mm FRLS PVC insulated copper conductor single core cable on surface / recessed Heavy class PVC conduit, with modular switch, modular plate, suitable GI Box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc as required
227	(a) One light point controlled by one 6Amps one way switch
228	(b) One ceiling fan point, Exhaust fan point controlled by one 6 Amps one way switch regulator
229	(c) One bell point controlled by one bell push
230	(d) One 3 pin 6 Amps switch socket outlet point on independent board
231	(e) One 3 pin socket outlet 6 Amps on the Point same board
232	Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor signle core cable on surface / recessed Heavy class PVC conduit, 2 way modular switch, modular plate, suitable GI Box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor signle core cable etc. as required
233	(a) One light point controlled by two way 6 Amps switch
234	Wiring for submain wiring 4Sq.mm – 2RM, 2.5Sq.mm - 1RMalong wtih earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed Heavy class PVC conduit as required (for 16 amps, power point)
235	Wiring for submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed Heavy class PVC conduit as required2 x 2.5 Sq.mm + 1 x 2.5 Sq.mmearth wire (Lightening Circuit)
236	Wiring for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed Heavy class PVC conduit as required(a) 2 x 6 Sq.mm + 1 x 6 Sq.mm earth wire (AC & Geyser)
237	Supplying and drawing co-axial TV Cable RG-6 grade, 0.7mm soild copper conductor PE insulated, shielded with fine tinned copper-braid and protected with PVC sheath in the existing surface / recessed steel / PVC conduit as required
238	Supplying and fixing of following sizes of Heavy class PVC conduit along with accessories on surface / recess including cutting the wall and making good the same in case of recessed conduit as required- 25 MM Dia PVC Conduit
239	Supplying and fixing modular telephone socket and TV socket including suitable modular gang box
240	Supplyand fixing of Modular switch one way 6 amps 1module 230V, 50Hz complete
241	Supply and fixing ofModular switch one way 16 amps 1module 230V, 50 Hz complete
242	Supply and fixing ofModular switch two way 6 amps 1 module 230V, 50 Hz complete
243	Supply and fixing ofModular fan step type regulator, 120W two module, 230V, 50Hz complete
244	Supply and fixing of Modular socket out let 6 Amps 230, 50 Hz volts AC 3 pin multipurpose type complete
245	Supply and fixing of Modular socket out let 6/16 Amps 230 volts, 50 Hz multipurpose complete
246	Supply and fixing off Modular Bell push 6A one module 230 volts, 50 Hz complete
247	Supply and fixing brass batten / angle holder including connection etec required
248	Supply and Fixing ceiling rose two to three terminal surface bakelite type AC 230 Volts, 50Hz complete
249	Supplying and fixing call bell / buzzer suitable for single phase, 230 Volts, 50Hz complete as required
250	Supplying and fixing LED fitting indoor batten light, 1 x 20w, output 6500 lumen230 V, 50Hz energy efficient, Box type aluminium housing with drive, connector block etc complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size (Phillips CAT No. BN100C LED20S-6500 PSUL120GRS4)
251	Supply, installation, Testing and Commissioning of 40W 2’x 2’ LED recess mounted light fixture including driver and fixing accessories etc complete (Phillips CAT No. RC380B LED 40S-6500 G4L 60W 60PSU OD)
252	Supplying and fixing LED fitting indoor Batten light, 1 x 10w, output 6500 lumen230v, 50Hz energy efficient, Box type aluminium housing, with Drive, connector block etc. complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size (Phillips CAT No. BN021 LED 12S 6500 PSU GR)
253	Supply and fixing LED post top lantern 40W, 5700K, energy saving, environmental friendly, designed with symmetrical light discussion, spum alluminium landscape luminaire, die cast alluminium land scape IP 65 luminaire suitable for pole dia 76mm dia complete (Phillips CAT No. BGP 300 LED 40757 PSU PC INS1)
254	Supply and Fixing linear LED high bay with IP54 type protection, 100W, 230V, 50 Hz and housing epoxy powder coated dia casted aluminium housing with bright anodised reflector and enclosed with heat resistant and toughened glass front visor including driver suitable for 140-270V AC, 50Hz fixing on pole / wall / bldg (including adjustment for up or down in pole or wall) side mounting suitable for 40/60mm OD Pipe and provisionof 3 core 2.5 SqmmPVC insulated PVC sheathed copper conductor multistranded wire upto fittingetc complete (Phillips CAT No. BY 515PLED 100S 5700 NB PSU GR)
255	Supply and Fixing LED road way lighting luminaires 30W with pressure die-cast powder coated suitable for building security light clear acrylic cover and complete accessories including drive with suitable connection complete (Phillips CAT No. BRPO46 LED 30CW MR S1 PSU GR)
256	Supplying and fixing 20A, 240V, 50Hz SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A \"C\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc as required
257	Dismantling of ceiling fan and painting the same with one more coats of spray painting with synthetic enamel paint of approved brand and manufacture to give an even shade, including cleaning of surface with detergent and replacing the damaged rubber reel, nuts and bolts with washers and safety pins, reinstalling the same as required
258	Supply & Fixing MCB single pole 5 Amps to 32 Amps 230V, 50Hz Complete
259	Supply & Fixing MCB SPN 240 Volts, 50Hz, 40 Amps 10 KV \"C\" curve complete
260	Supply & Fixing MCB TPN 415 Volts, 50Hz 63 Amps 10KA \"C\" Curve complete
261	Supply and Fixing in replacement MCCB with rating of 200 Amps, 415 Volts, 50Hz 4 pole with 25 KA breaking capacity thermal magnetic adjustable of overlead & short circuit release as per IS-13947 & IEC 60947 - 2 & the service short circuit breaking capacity should be 100% of ultimate breaking capacity with inbuilt display for currentmetering with accuracy of Class 1, MCCB should be with suitable spreaders and phase barriers for each terminals with all accessories
262	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415V, 50Hz on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc as required (But without MCB/RCCB/Isolator) 4 way (4+12) Double door
263	Supplying and fixing following way single pole and neutral, sheet steel, MCB distribution board, 240 V, 50Hz on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc as required (But without MCB/RCCB/Isolator) 12 way, Double door
264	Supply and Fixing Bollard light fitting LED 10W, 230V 50Hz with pressure die cast powder coated housing with PC diffuser, efficient high output SMD LED for garden, pathway etc, lighting IP 66 protection and all accessories internally pre wired core twisted flexible copper conductor cable with suitable size complete (Crompton LB LTW-10-WW)
265	Earthing with G.I earth plate 600mm x 600mm x 6mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required all as per IS 3047
266	Providing and laying earth connection from earth electrode with 6 SWG dia G.I wire in 15mm dia G.I pipe from earth electrode including connection with G.I thimble excavation and re-filling as required.
267	Providing and fixing 25 mm X 5 mm G.I strip in 40 mm Dia G.I Pipe from earth electrode including connections with G.I nut ,bolt,spring washer excavation and refilling etc as required.
268	Taking down carefully storage type water heater (geyser) any make capacity from clamp nut / bolts including disconnecting water and electric connection and fixing the same after renovation of building if any connecting up after cleaning of geyser and refixing the same complete
269	Fixing of exhaust fan of suitable make & match with the existing surface after fixing, complete including making holes
270	Supply & fixing of exhaust fan of light duty 300mm sweep 230 volts, 50Hz single phase complete with louvers
271	Supply & fixing of exhaust fan of Heavy duty 450mm Sweep, 230 volts, 50Hz, single phase complete with Louvers as Specified.
272	Supply and fixing of ceiling fan complete without electronic type regulator and accessories 230V, 50Hz 1200mm sweep, BEE 5 star rated with down rod etc.
273	Supply and fix electric water heater, storage type steel body 230 volt 50Hz with copper inner tank and heating element upto 2KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety Valve, thermostate, NRV complete
274	Supply and Fixing wall mounted fan 400mm sweep 230 volts, 50 Hz complete
275	Supplying and fixing following size / modules, GI Box alongwith modular base & cover plate for modular switches in recess etc as required Module (100mm x 75mm)
276	Supplying and fixing following size / modules, GI boxe along with Modular base & cover plate for modular switches in recess etc as required 6 Module (200mm x 75mm)
277	Sub Head - XIII External Water Supply
278	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. Complete :(a) 50 to 80 mm nominal bore
279	Providing and fixing G.I. pipe complete with G.I. fittings including trenching and refilling etc. External work(a) 25 mm dia nominal bore
280	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :(a) 25 mm nominal bore
281	Sub Head - XIV External Electric Supply
282	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required including end terminations with proper size of Aluminium lugs.
283	(a) Upto 35 sq. mm
284	(b) Above 35 sq. mm and upto 95 sq. Mm
285	(c) Above 185 sq. mm and upto 400 sq. Mm
286	Supply, installation, Testing and Commissioning of 3 phase and Neutral 415V, 50Hz 4 wire , Free Standing Floor mounted MVpanel made out of 14 SWG MS sheet after seven tankprocess and painting with Epoxy powder coating. The panel shall consist of suitable ratingTPN Aluminium busbar (at the rating of 0.8A/Sq.mm) supported with DMC/ SMC barriers and color coded with Heat shrinkable sleeves.The Metering shall be provided as specified. The panel shall have Short circuit withstanding capacity of minimum 50 KA and consist of the switchgear as mentioned below.The panel shall be got fabricated from manufacturers with CPRI Test certificate only. . The size of all Panel Mounting Meters shall be 96X96mm. The Panels shall be mounted on U channels including supply and fixing of the same. Indication lamps of LED type. For all Electrically operated Breakers, Selector switches shall be provided for controlling.
287	MAIN LT PANEL - 2- OutdoorIncomer 1 : 1 No of 250 A, 4P.MCCB, 36KA, 415 Volts, 50Hz shallbe supplied with S/C,E/F,O/C AND INSTANTANEOUS TRIP RELAY UNIS WITH TIME DELAY SETTINGS. 2A, control fuse - 3 Nos.RYB indicating lamps - 1 setVoltmeter (0-500V) with selector switch - 2 setAmmeter (0-250A) with selector switch - 2 set250/5A, CL-1, 15VA CT\"s with resin cast- 3 nos.Outgoing100A, 4P, 25KA, MCCB, -=4No63A, 4P, 16KA, MCCB, -=3No40A, 4P, 16KA, MCCB, -=1NoOn Loadchanger Switch 4P, 415V, 50Hz 100A :1NoBus Bars : 400A, 3Ph, 4 wireTPN, 50Hz, aluminium bus barsMetering Instruments ; Load Manager in the Incomer and MCCB on , off , Trip Indication Lamps and with Breaker Status indication Lamps and also with Phase indication Lamps.Earth Bus; To be provided at the bottom of the Panel of copper
288	Supply and fixing LED Street light fitting with IP 66 type protection, 46W ,CCT (K) 230 Volts, 50Hz and housing epoxy powder coated die casted alluminium housing with bright anodised reflector and enclosed with heat resistant and toughned glass front visor including constant current driver suitable for 140-270V AC , fixing on pole /wall/building side mounting suitable for 40-60 mm OD pipe and provision of 3 c x2.5 Sqmm PVC insulated PVC sheathed copper conductor multistranded wire upto fitting complete all as specified and directed. (Bajaj CAT No. BPRO 46 LED 30CW MR S1 PSU GR)
289	Providing and fixing tubular swaged pole in replacement , type 410 - SP- 22 ( 8.8 Mtr long ) and painting with two coats of alluminium painting over a coat of red oxide primer & white wash for PCC coping etc complete.
290	Erection of steel tubular or rail pole strut in cement concrete 1 : 3: 6 ( 1 cement : 3 coarse : 6 graded stone aggregae 40 mm nominal size ) foundation including excavation and refilling and secured with holding clamps ,bolts nuts etc complete.
291	Supply & fixing in SMC junction boxes (weatherproof ) IP-66 on street light poles made out of thermoplastic of size not less than 295x195x100 mm size with connector for connecting incomer and outgoing of cable including provision of 01 no ofSP MCB 6A,10KAto control the pole light circuit and MS bracket s made out of 32 x 4 mm ms flat for fixing the box on post complete with nuts and bolts and washers and suitable size of double compression glands for incoming ,outgoing cables etc complete.
292	CREDIT FOR THE FOLLOWING UNSERVICEABLE ITEMS:-
293	Point wiring, switches, sockets, boards etc obtained against item no. 173.00
294	Submain wiring obtained against item no. 177.00 & 178.00
295	Light fittings obtained against item no. 192.00 to 197.00 and 226.00
296	DB along with all MCB, MCCB, Isolator obtained against item no. 204.00 & 205.00.
297	Exhaust fan obtained against item no. 212.00 & 213.00
298	GI Tubing of 25mm dia obtained against item no. 221.00
299	Gun Metal Gate Vaue of 25mm dia obtained against item no. 222.00
300	Tubular swaged pole 8.8 metre long obtained against item no. 227.00

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Telangana Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Additions/ Alteration And Renovation To Building No. P-120, P-122 And P-177 (Dlomi) At Drdo Township, Kanchanbagh, Hyderabad., Hyderabad-Telangana

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Additions/ Alteration And Renovation To Building No. P-120, P-122 And P-177 (Dlomi) At Drdo Township, Kanchanbagh, Hyderabad., Hyderabad-Telangana

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us