|
| 1 | Dismantling clearing away and carfuly stacking materials useful for reuse the existing Floor finish and dadooing walls in cement mortar with mosaic tiles / glazed tiles / cuddapah slabsh etc. complete as per the standard specification |
| 2 | Dismantling, clearing away and carefully stacking materials useful for re-usefor any thickness of Brick / stone masonry in Cement mortar walls under 3m high etc, complete |
| 3 | Dismantling, clearing away and carefully stacking materials useful for re-usefor any thickness of Doors & windows etc, complete |
| 4 | Clean removal of Cement plaster from walls etc, |
| 5 | Dismanling and clearing away carefully stacking the materials useful for reuse for Reinforced Cement Concrete etc., complete |
| 6 | Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) |
| 7 | For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. |
| 8 | Cement Concrete 1:2:4 (One Cement, Two M- sand and Four hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers |
| 9 | For Ground Floor Superstructure |
| 10 | Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.(Contractor has to make his own arrangements for the supply of steel and binding wire) |
| 11 | Brick work in Cement Mortar 1:5 (one cement and five M.sand) using best quality II class ground moulded chamber burnt bricks of size 9\" x 4-3/8\" x 2-3/4\" for foundation and basement including curing, etc., complete complying with standard specifiction. |
| 12 | For Ground Floor Superstructure |
| 13 | Brick partition walls of 11.50cm thickness using best quality II class Ground moulded chamber burnt bricks of size 9\" x 4-3/8\" x 2-3/4\" in Cement Mortar 1:3 (One Cement and Three M- Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately) |
| 14 | For First Floor Superstructure |
| 15 | Open terrace floor area chemical treatment. Cleaning the surface thoroughly scrapping, wire brush and water to get clean surface further all tiles joints “V” grooves will be refilled with Dr.Fixit URP Co Polymer with cement and tile adhesive powder 1:2:3 ratio and applying, later than first coating of acrylic polymer oil prime seal. After that we will be applying and fitting fiber glass mesh impregnated with 110 GSM over that apply two coats fosroe brush bon chemical for FRB Lining Complete the work. |
| 16 | Paving the floor with best quality Double matt finish Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M- sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification.(The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 17 | Flooring with plain ceramic tiles of size305x305x6mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M-Sand)base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification.(The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 18 | Dadooing walls with best approved quality colour glazed tiles of sizes 300x450x8mm set in Cement Mortar 1:2 (One Cement and Two M- sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. |
| 19 | Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three M- sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 20 | Supplying and fixing colour galvanum sheet 0.47mm thick for roofing of approved quality by drilling holes (and not by punching) with necessary \"J \" / \"U\" bolts and nuts of 8mm dia of suitable length and providing one set of bitumen washers of 25mm dia and 1.60mm thick for each bolt including protruding portion of bolts in roof shall be covered with bitumen compound etc., complete complying with standard specification and as directed by the departmental officers. |
| 21 | Renewing and fixing the following size of M.S Square / Rectangular hollow tubular sections of best variety and approved quality for purlins for fixing the colour galvanum sheet for roof including cutting the MS hollow tubular section to required size and placed in roof to required gradient and welded and providing necessary concrete for the hollow tubes embedded in the wall for rigiding by dismantling the brick masonry and redoing the same. The rate is inclusive of cost of square / Rectangular MS hollow tubular section labour charges for cutting welding and fixing in position one coat of red oxide primer and excluding cost of colour galvanum sheet aad all the incidental charges etc complete complying with standard specification and as directed by the departments officers. |
| 22 | Size of 50x50x3.50mm |
| 23 | Size of 25x25x3.50mm |
| 24 | Supplying and fixing of M.S. Grill of approved design for doors, windows, open courtyard, Grill gate etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specifications. |
| 25 | Supplying, fabricating and fixing in position anodised aluminium natural colour matt finish Openable window with four panels in all floors and made with extruded aluminium section of the sizes given below with necessary acessories such as rubber beading, hinges, stay hook, handle supplying and fixing 4mm thick plain glass including cost of all materials, labour power consumption required for fabrication, drilling holes in RCC column/ floor slab/masonry wall wherever necessary with power drills to the required extent and made same to original condition after fixing etc.,complete .The aluminium sections are to be anodized with matt finish under electrically controlled condition in accoradance with ISI 1868/1962 specification for an average anodic film thickness of not less than 15 microns All aluminium sections and furniture fittingsshould be got approved by the Exe. Engr., before use on works.Outer Frame - section 38x33x21x2.4mm @ 0.615 Kg/mShutter Top & bottom and Vertical section-38.50x33x24.5x3 & 4mm @ 0.706 kg/m, Lock section - 59 x 33 x 25 x 2.5mm @ 1.135 kg/m .Glazing clip section - 0.101 Kg/m. |
| 26 | Renewing and fixing Polyester fiber Window Mosquito mesh with using Velcro tape including cost of material, stitching charges and labour chargers for fixing etc, complete |
| 27 | Supplying and fixing of Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames.15mm MS square tubes for top, lock and bottom rails.The steel tubes shall be covered with 5mm thick solid PVC sheets.Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm.The over all size of top rail,Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter. |
| 28 | FRAME:Fully Solid core WPC - 75mm x 50mm:Providing & Fixing of Qute WPC / PVC Solid door frame exttruded with size 75mm x 50mm. The inner Core made of rigid WPC compound with minimum shore hardness of 55, and Bulk Density 0.80 Grms/ Cub.C.Mt. The frame shall be fixed to the wall using 10 x 100mm long M.S Screw through the frame by using PVC fasteners. A minimum of 4 nos screw to be provided for each vertical member |
| 29 | Supplying and fixing of wood polymer composite (WPC) door with solid door frames extruded with size 75mmx50mm. The inner core made of rigid WPC compound with minimum shore hardness of 55 and buld density 750kg/cub.Mt. The frame shall be fixed to the wall using 10x10mm long MS screw throught the frame by using PVC fasteners. A minimum of 4nos screw to be provided for each vertical members, Door Shutter of 25mm thick Wood Polymer Composite (WPC) single core Extruded Door Shutter, with one side digital printing of specified Design which is approved by engineering-in-charge. Both side of the shutter shall have rough sugar texture finish, laminated with UV oil. The solid WPC board shall have minimum shore hardness of 55 and Bulk density 550kg/cub.Mt moulding the thickness remains 25mm (+/-1mm) etc. complete as per the direction of the departmental officers.(make Qute / Equivalent) |
| 30 | Supplying Fabricating and placing in position of Aluminium powder coating of any colour matt finish fixed Partition top half glazed with 5.50mm thick plain glass and bottom half with medium density fibre board of 12mm thick both side pre laminated for cubical and the outer frame of the Aluminium section of size 101.60x44.45x3.18mm @ 2.319Kg/m. at internal vertical 2 Nos & Horizontal 1 No, mullion of aluminium section of size 62 x 38 x 2mm @ 1.174 Kg/m with necessary aluminium clips of size 79.15 x 17.27 x 1.50mm at 0.176 Kg/m with necessary rubbor beading L angles including dismantling and redoing masonry as concrete where necessary etc., complete.The Aluminium section are to be anodised with matt finish under electrically controlled condition in allfdjsfdslk with ISI 1868 / 1962 specification for an average anodie film thickness of not less than 15 microns.All aluminium sections are should be got approved by Engineer incharge before use on works. |
| 31 | Supplying and fabricating and fixing in position aluminium anodised door with door shutter partly top 2/3 galzed and partly bottom 1/3 panelled door and frame made out of box section 101.6x44.45x3.18mm thick at 2.319 kg\m door shutter made out of box section 47.1x44.45x2.5mm at 1.202 kg\m for vertical style and top, lock rail sections of size 50 x 44.45 x 2.50mm @ 1.292 Kg/m and bottom section 100.4x44.45x2.50mm at 1.974kg\m using clips of size 17.15x17.27x1.5mm at 0.176 kg\m with rubber beading, strike plate type handle ofsize 100x30x1.60mm at 0.988 kg\m on both sides, tower bolts, lock and top 2/3 portion with5.50 mm thick plain glass and bottom 1/3 portion with both side prelaminated board ( MDF ) 12mm thick for panel portion with one floor springs including cost of all materials labour power consumption required for fabrication, drilling holes in RCC columns floor slabs masonry wall wherever necessary with power drills to the required extent and make the same to original condition after fixing and as directed.All the aluminium sections are to be anodised with matt finish under electrically controlled condition in accordance with IS 1868-1962 for an average anodic flim thickness of15 microns etc., complete. The materials should be got approved by the Executive Engineer before use on works. The rate shall be inclusive of all materials labour for fixing transportation loading, unloading, charges. (Double leaves Door) |
| 32 | Plastering with Cement Mortar 1:5 (One cement and Five P.sand), 12mm thick with Admixture in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 33 | Cleaning and removing existing loose plaster, fungus either sude applying the FOSROC REBAKLES chemical directly apply the rusted RCC roof rods for removing the corrode after 20 minutes remove the corrode from roof using waste cloth to clean the surface and using the FOSROCanti corrosive NITROIC primer applying the chemical mixing of (60 ml+40 ml) in the damaged ceiling roof rods after romoving the corrode in dead apply the FOSROC NITRO BOND SBR in roof surface with in 30 minutes etc., complete complying with standard specification. |
| 34 | Plasteringwith cement mortar 1:3 (One cement & three P-sand) for the 12mm thick with fine p.sand for plastering adding FOSROC NITRO BOND SBR1 litres including curing, neat finishing, etc. complete complying with standard specification and as directed by the departmental officers. |
| 35 | Easaning the doors and windows including fixing furniture fitting etc., complete |
| 36 | Repainting two coats of old plastered wall surface with ready mixed plastic emulsion paint of first class quality including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. |
| 37 | Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm \"P\" or \"S\" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications.(The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works) |
| 38 | Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm(without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia \"B\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works). |
| 39 | Supplying and fixing position PVC Nahani Trap / Floor Trap of the sizes 100 x 75mm with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of M-sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three M-sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works) |
| 40 | Supplying and fixing of stainless steel of Health faucet of approved quality and board etc., complete complying with standard specification |
| 41 | Renewing, laying and jointing UPVC pipes (handle higher water pressure) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications.The UPVC pipes shall be got approved by Executive Engineer before use on works. Internal water supply |
| 42 | 32mm dia UPVC pipe |
| 43 | 25mm dia UPVC pipe |
| 44 | 20mm dia UPVC pipe |
| 45 | Renewing UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements |
| 46 | 32mm dia UPVC Elbow |
| 47 | 32mm dia PVC Tee |
| 48 | 25mm dia UPVC Elbow |
| 49 | 25mm dia PVC Tee |
| 50 | 20mm dia UPVC Elbow |
| 51 | 20mm dia PVC Tee |
| 52 | Renewing and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level |
| 53 | 75mm dia PVC/Soil waste pipe |
| 54 | 110mm dia PVC soil / waste pipe |
| 55 | Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of \"U\" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. |
| 56 | 110 mm dia (In building with ground floor only) |
| 57 | 110 mm dia (In building with First floor only) |
| 58 | Renewing and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). |
| 59 | 75mm dia PVC Elbow |
| 60 | 110mm dia PVC Elbow |
| 61 | 110mm dia PVC Door Elbow |
| 62 | 110mm dia PVC Door Tee |
| 63 | 110mm dia PVC Cowl |
| 64 | Renewing and fixing of cylindrical vertical notational polythene water storage tank of 1000 litres capacity confirming to IS 12701/96 the tank is meant for outer (or) indoor, use complete with removable hinged top locking arrangements and to make provision to fix simply with pipe lines with necessary manhole with cover and including all PVC specials, plugs, screws, nails to fix the tank etc., (The water tank should be got approved by the Executive Engineer before use on works) |
| 65 | Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements).The valves to be used on work shall be got approved by the Executive Engineer before use on work. |
| 66 | 25 mm dia G.M. Gate Valve |
| 67 | 32 mm dia G.M. Gate Valve |
| 68 | Supplying and fixing in position 15mm dia brass CP screw down tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Executive Engineer before use on the works) |
| 69 | Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise andsimilar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three M- sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification. |
| 70 | SUB TOTAL |
| 71 | GST @ 18 % |
