|
| 1 | Painting two coats with ready mixed Plastic Emulsion Paint S.I.358 Plastic emulison paint of\"approved quality and colour over a priming coat, including thoroughscraping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers. TNBP No:66-A (Sl.No.358) |
| 2 | Painting new wood work with two finishing coats of ready mixed synthetic enamal paint over one coat of ready mixed primer of approved quality etc., complete as per standard specification. |
| 3 | Painting with two coats of Approvedcolour of best quality synthetic enamel paint, painting over old iron work including cost and conveyance of all materials and all labour charges etc. complete as per Standard specification and as directed by the departmental officers. (Old Iron Surface).TNBP No:66&66-A |
| 4 | Brick work in cement mortar 1:5 mix using (One cement and five sand)using best quality ofIIIclass Countrybricks of size (8 3/4\"x4 1/4\"x 2 3/4\") for foundation including curing cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification TNDSS specification No.31 & 31C- 10m3 |
| 5 | Supplying and erecting steel centering for sides and soffits including supports and strutting upto 3.29 m height for plain surface as RCC slabs, rectangular tee (or) elbeams, lintel, bed block stair case waist slab, landing slab, etc., complete as per standard specification - 10m2 as per TNDSS & Morth specification No:30 & 36 |
| 6 | Reinforced cement concrete 1:11/2:3 (one cement one and half sand and three aggregate) using 20mm size I.S.S. metal including cost conveyance of materials to site and all labour charges etc., mixing laying consolidating curring etc., but excluding cost of steel etc., complete as perstandard specification as per TNDSS NO: 30 V,VI (S3) VII-3 |
| 7 | Supplying, fabricating and placing in position of mild steel or TMT rods, including cost of steel and binding wire and all labour charges for cutting, bending, tying and placing in position etc, complete as per SS. TNDSS NO: 97 V,VI (S6) VII (S6) VII-3 |
| 8 | Plastering in cement mortar 1:3 (one cement three sand) using 10mm thick including cost and conveyance of all materials and labour charges etc, complete as per standard specification. [MoRTH Specification: Clause:1000/1300] |
| 9 | Plastering in cement mortar 1:4 (one cement Four sand) using 12mm thick including cost and conveyance of all materials and labour charges etc, complete as per standard specification. [MoRTH Specification: Clause:1000/1300] |
| 10 | Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames.15mm MS square tubes for top, lock and bottom rails.The steel tubes shall be covered with 5mm thick solid PVC sheets.Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm.The over all size of top rail,Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter. |
| 11 | Supply and fixing of mild steel grill works for windows, ventilators, etc including redoxide priming coat and cost of materials and all labour charges etc. complete. |
| 12 | Painting two coats over new iron workwith ready mixed paintof apprved quality and colour including cost of all materials and labour charges etc complete as per SS |
| 13 | Floor Finishing First Quality Design Ceramic tiles of All colours of sizes 305mm x 305mm x 6mm. laid in cm 1:3 mix 10mm thick and pointing with white cement using 0.4kg/sqm including finishing the joint and pointing flush with tiles surface etc complete |
| 14 | Dadooing with glazed tiles of 300mm*200mm*6mm size of approved quality and colour set in c.m 1:2mix (one cement and two sand) 10 mm thick and pointing with white cement using 0.4 kg /m2 neatly as directed -including cost of all materials and labour charges etc complete as per SS |
| 15 | Supplying and fixing in position of false ceiling arrangements with aliminium anodized \"T\" section and \"L\" angle frame work of grid of size 60x60cm with aluminium \"T\" section and \"L\" angle of size 25x25x2mm thick and the same is supported at suitable intervals by adjustable type 6mm dia M.S rod with suitable threaded nuts suspended rods hung from ceiling at 100cm c/c in both directions and fixing 60x60x20cm thick thermocole in the grid so as to give a seat to false ceiling including painting the 6mm dia M.S rod etc. complete complying with standard specifications. Necessary openings and arrangements for fixing electrical fittings should be provided with suitable frame work etc.complete. |
| 16 | Supply and fixing ofGalvalum sheet (Pre painted)6mm thickincluding 15cm lapping roofingwith necessary \"J\" bolt and nut, bitumen washer and Screws if wooden baterns including cost and conveyance of all materials and all labour charges etc Complete complying with Standard specifications. |
| 17 | Supplying and fixing of steel TRUSSES work using MS angles and \"T\" sections each according to design approved by the departmental officers including cutting, welding and cost of conveyance and all materials to work site. |
| 18 | Supplying, fabricating and fixing in position of aluminium anodised natural colour matt finished door of size 1.00m x 2.10m single leaf with shutter fully panelled with both side prelaminated MDF boards of 12mm thick. The door frame shall be of anodised aluminium box type section of size 101.6x44.5x2.5 mm @ 1.202 kg/m for vertical, top and lock rails using box type section of 50x44.5x2.5 mm @ 1.292 kg/m and bottom rail using box type section 100 x 44.5 x 2.5 @ 1.974 kg/m. The shutter shall be fully panelled with 12mm thick both side prelaminated MDF boards and fixed to the shutters frames using aluminium clips of section 17.15x17.27x1.5mm @ 0.176 kg/m and rubber beading. The shutter shall be provided with aluminium handle section No. 5140 of size 100x30mm @ 0.988 kg/m provided for the full width of shutters on either sides. The rate shall be inclusive of the following furniture and accessories like rubber beading, PVC felt, L angle, 150mm aluminium tower bolt-2 Nos, door closer-1 No, Aluminium Hinges - 3 No, Aluminium door stopper - 1 No, screw, plug etc.labour charges for fabrication, fixing and for dismantling |
| 19 | Supplying and fixing in position colour Europen water closet with low level flushing tank of 10 lit capacity of best quality and approvel make with 100mm \"p\" or \"s\" trap with double flapped rigid PVC seat cover with CP brass etc. Complete complying with standard specifications and as directed by the department officers ( EWC should got approvel by the executive work before use on work.) |
| 20 | Supplying & Fixing in position of white glazed Indian type water closet with \"P\" (or) \"S\" trap and Orissa slope set in brick jelly cement concrete 1:4:8 100mm thickusing 20mm thick brick jelly ISS gauge and finished to sludge out any leakage and defalut including cost of WC \"P\" (or) \"S\" trap and foot rest etc., complete - 1No. |
| 21 | Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A FT switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator) |
| 22 | Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point |
| 23 | Supply and fixing of 1200mm (48\") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp |
| 24 | Plain cement concrete Using1:4:8 mix ( One cement , four Sand and Eight aggregates) using 40 mm ISS HBG metal including cost and conveyance of all materials to work site and all labour charges for mixing, laying,consolidating and curing etc complete as per the standard specifications. TNDSS NO: 28 V, VI (S2) V,VI (S5A) VII |
| 25 | Plain Cement concrete 1:2:4 (one cement, two sand and four aggregates) using 20mm ISS HBG metal including cost of all materials and labour charges for mixing, laying, compacting and curing etc, complete as per standard specifications. TNDSS NO: 30 V,VI (S3) VII-3 |
| 26 | Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia \"B\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works). |
