Tender For Construction Of Media Centre At District Chitrakoot, Chitrakoot-Uttar Pradesh

TDR : 40428002

Tender Notice
BOQ

Expired

Chitrakoot , Uttar Pradesh

Tender Brief : Tender For Construction Of Media Centre At District Chitrakoot

Document Fees
₹ 7080 /-

EMD
₹ 640000.0 /-

Tender Value
Refer document

Submission Date
30-11-2023

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :300 mm dia piles
2	Vertical load testing of piles in accordance with I. S. 2911 ( part iv ) including installation of loading plateform & preperation of pile head or construction of test cap & dismantling of test cap after test etc. complete as per specification and the direction of Engineer - in - Charge . Initial Test
3	Vertical load testing of piles in accordance with I. S. 2911 ( part iv ) including installation of loading plateform & preperation of pile head or construction of test cap & dismantling of test cap after test etc. complete as per specification and the direction of Engineer - in - Charge . Routine Test
4	Excavation in foundation in ordinary soil Loam clay or sand including lift upto 1.5 meter and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as direction by the Engineer in charge upto a distance of 30m from the foundation trenches.
5	Earth work in cutting or embankment(Carted earth) in ordinary soil excavation to be in the form of regular pits not exceeding 1/2 meter(20) in depth and earth work in embankment to be in 20 Cm(8) layers including ramming and dressing the surface to required levels and slopes and also including 1.5meter lift and 30 m led. The earth from cutting to be used in marking imbankment or to be deposited as spoil bank with in 30m distance as directed by the E/I.
6	Cement concrete with 4 Cm guage approved stone ballast approved coarse sand and cement in the proportion of 8:4:1 including supply of all material labour and tools and plants etc required for proper completion for the work.
7	Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8km from the site of work and including watering ,dressing etc rate to include cost of all materials, labour T&Petc. Required for proper completion of work .
8	Providing and injecting chemical emulsion for pre constructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete. (plinth area of the building at ground floor only shall be measured as per I.S.6313 (PartII 1981) Alderine emulsifiable concentrate or any other approved material such as Heptrachlor or Chlordane will be used. The rate of application of chemical emulsion shall be as follows : (1) Treatment for masonary & foundation 5 liters per sqm. (2) Back fill in immediate contact with foundation 7.5 liters/sqm (3) Treatment of top surface of plinth filling 5 liters/sqm (4) Treatment junction of wall and the floor 7.5 liters /sqm (5) Treatment of soil along external perimeter of building 7.5 liters/sqm (6) Treatment of soil under apron along external perimter 5 liters/sqm. (As per manufacturer\"s standard dilution)
9	R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in Foundation excluding supply of reinforcement and its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. Binding wire to be supplied by the contractor free of cost.
10	R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. Binding wire to be supplied by the contractor free of cost. (GF + FF)
11	R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. Binding wire to be supplied by the contractor free of cost. (Second Floor)
12	R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in sunshade excluding supply of reinforcement and its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works.Binding wire to be supplied by the contractor free of cost. (GF + FF)
13	R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in slab excluding supply of reinforcement and its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works.Binding wire to be supplied by the contractor free of cost. (second Floor)
14	R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lighter beam excluding supply of reinforcement and its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works.Binding wire to be supplied by the contractor free of cost. (GF + FF)
15	R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lighter beam excluding supply of reinforcement and its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works.Binding wire to be supplied by the contractor free of cost. (second Floor)
16	R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in coloumn excluding supply of reinforcement and its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works.Binding wire to be supplied by the contractor free of cost. (GF + FF)
17	R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in coloumn excluding supply of reinforcement and its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works.Binding wire to be supplied by the contractor free of cost. (Second Floor)
18	Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including binding for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured.
19	Class-150 brick work in 1:6 (one cement and six coarse sand sand of 2.25 fineness modulus) mortar infoundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work.
20	Providing and laying damp-proof course 40mm thick with cement consisting of concrete part cement 1.5 approved coarse sand 3 approved 13 mm stone grit including water proofing material as ordered by the E/I in proportion as specified by the manufacturer.
21	Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
22	Class-150 brick work in 1:6 cement and coarse sand of 2.25 fineness modulus mortar butin superstructure includingnecessarycutting and moulding of brick work asrequiredand also including honeycombedbrick but walls of one brick thick(GF + FF)
23	Class-150 brick work in 1:6 cement and coarse sand of 2.25 fineness modulus mortar butin superstructure includingnecessarycutting and moulding of brick work asrequiredand also including honeycombedbrick but walls of one brick thick(Second Floor)
24	Class-150 brick work in 1:4 cement and coarse sand of 2.25 fineness modulus mortar butin superstructure includingnecessarycutting and moulding of brick work asrequiredand also including honeycombedbrick but walls of half brick thick .(GF +FF)
25	Class-150 brick work in 1:4 cement and coarse sand of 2.25 fineness modulus mortar butin superstructure includingnecessarycutting and moulding of brick work asrequiredand also including honeycombedbrick but walls of half brick thick .(second Floor)
26	Providing and fixing to existing door frames 30 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).
27	Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.
28	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
29	Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws 35 mm thick shutters With ISI marked stainless steel butt hinges of required size Second class teak wood.
30	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge Second class teak wood 35 mm thick shutters
31	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).
32	Mild steel or iron workofsmall sizes and sections suchas holding down bolts, holdfast tierods, gratings etc.(when not included in and over all rates) brought to requiredfrom including supply of steel & its wastage including cost of bolts,nuts,if required forand welding,grinding and making holes as required for proper completion of the work. Fabrication of grill/stairs case railingGround floor
33	Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and UPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).(3 Track Slider window with mesh)Ground floor
34	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class teak wood 30 mm thick shutters
35	Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge.(a) Door chaukhats
36	Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge.(b) Window chaukhats
37	Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge.(c) Ventilator chaukhats
38	15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) (Plinth plaster)
39	12mm thick plasteron brick work minimum thickness not less than 10 mm with 1 part of cement and 6 part of approved coarse sand of 2.25 fineness modulus.Ground floor
40	12mm thick plasteron brick work minimum thickness not less than 10 mm with 1 part of cement and 6 part of approved coarse sand of 2.25 fineness modulus.second Floor
41	12mm thick plaster on rough surface brick work minimum thickness not less than 10 mm with 1 part of cement and 6 part of approved coarse sand of 2.25 fineness modulus. Ground floor
42	12mm thick plaster on rough surface brick work minimum thickness not less than 10 mm with 1 part of cement and 6 part of approved coarse sand of 2.25 fineness modulus. second Floor
43	Making grooves 10 to 12mmwide x 8 mm deep inplaster of the walls or in ceiling vertically or horizontally as required.
44	Providing and laying of 8 to 10 mm thick ivory or light shade vitrified tiles of 600mm x600mm size in flooring or skirting laid with 1:3 cement mortar (1cement :3 coarse sand ) finishing with cement slurry & pigment grouting & Polishing complete i/c supply of all material labour T&P etc. required for proper completion of work .excluding base concrete
45	Supply and fixing 6mm (1/4\"\") China white glazed tiles in flooring and skirting laid with ratio 1:3 cement and approved coarse sand finished with white cement slurry jointing and polishing complete, including supply of all materials,labour and T&P etc.Required for proper completion of work.
46	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour and shade Area of slab over 0.50 sqm
47	Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent.
48	Kota Stonework in Flooring and Skirting (machine cut egdes veneer work) for wall lining upto 10.00 M height,backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement :3 coarse sand) and jointed with cement mortar 1:in flooring 25 mm thick & joint filled with 1:2 (1 cement:2 Stone dust) including rubbing and polishing complete.
49	Painting or varnishing new steel work in small areas or new wood with one coat (up to one sq. meter) of ready mixed priming paint and one coat of approved superior quality ready mix paint (2nd quality synthetic enamel paint of approved brand such as British paint shalimar Asian or equivalent supply of all material labour T & P etc required for proper completion of work.Paint to be used should confirm the ISI No. 103-1950
50	Melamine polishing on wood work (one or more coat).
51	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
52	Finishing walls(Two coats) with acrylic emulsion paint ofapproved brand and manufacture and of required shade on undacorated wall surface to give an even shade over including curing and cost of all material labour T & P etc required for proper completion of work.
53	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
54	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
55	S/F of 4.0 mm thick Panes of glass with and Including Atul or Equivalent ISI mark quality putty and brads and spring incluing supply of all materials labour and T&P etc. required for proper completion of work.
56	Providing & fixing stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm
57	P/Fixing stainless steel tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as / IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.250 mm x 10mm
58	Providing & fixing stainless steeldoorhandleswith screwsand 150mm long.SI marked
59	Providing and laying \"Brick Coba\" 100 mm thick laid M-150 class brick ballast coba 7.50 cm thick with gap of 15 mm to each other, over 20 mm thick base of cement morter 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurrymixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compoundin 1:4 cement and coarse sand mortar finished smooth & Top mashed false square 30 cmx 30 cm and side wall parapet shall be monolythic plaster wall upto 30 cm higher & junction and corners shall be rounded by brick ballast cement and coarse sand masonary Coba with top finished plaster mixed with acetic water proofing compound @2% by weight and including supply ofall material, labour T & P etc complete for proper completion of work.
60	Construction of drain of size 150 x 150 mm along with apron including excavation,base concrete 1:4:8 in thickness of 7.5cm of and brick work in foundation 1:4( 1 cement : 4 coarse sand) and brickwork in half brick thick in foundation 25mm thick cement concrete (1:2:4 mix) flooring base and 20mm thick plaster (1:2) finished with neat cement. with glass strip
61	Providing and fixing fly proof galvanized M.S. wire gauge to windows and lerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.With 2nd class teak wood beading 62X19 mm
62	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
63	Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \"T\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \"T\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \"T\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.
64	Cement concrete with 20mmguage approved stone ballast approved coarse sand and cement in the proportion of 4:2:1 including supply of all material labour and tools and plants etc required for proper completion for the work.
65	Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
66	Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
67	Glass fibre Reinforced concrete ( GRC JALI ) grade -10 including supply of all material labour and tools and plants etc. required for proper completion for the work.
68	Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry
69	Mild Steel or iron work in heavy sizes such as trusses,built up gates,door frames record racks roof work,gates etc. wrought to required form including drilling holes rivetting or welding where necessary and also including supply of steel bolts nuts etc & their required for proper completion of the work. (PWD 503)
70	Cement concrete with 20 mm guage approved stone ballast approved coarse sand and cement in the proportion of 3:1.5:1 including supply of all material labour and tools and plants etc required for proper completion for the work.
71	Class-150 brick work in 1:4 (one cement and six coarse sand sand of 2.25 fineness modulus) mortar infoundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work.
72	Making grove cutting in c.c. road
73	Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade \"A\" sealing compound
74	2 cm thick cement plaster in dado or skirting in 1:2 consisting of one part of cement and 2 parts of approved coarse sand laid in panels finished with 3 mm floating coat of neat cement or cement & marble dust in ratio of 5:1 including supply of all materials labour & t & P etc equired for proper completion of the work.
75	25mm thick 1:2:4 cement concrete floor with cement approved coarse sand and 2 cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified over and excluding 8cm local sand and brick ballast 4cm guage in the proportion of 1:4:8 and removing any overlapping mortar at the joints of panels if any giving them a uniform finish including supply of all materials labour T & P etc required for proper completion of the work.
76	Excavation in foundation in ordinary soil Loam clay or sand including lift upto 1.5 meter and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as direction by the Engineer in charge upto a distance of 30m from the foundation trenches. (1.50 TO 3.00 M)
77	Excavation in foundation in ordinary soil Loam clay or sand including lift upto 1.5 meter and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as direction by the Engineer in charge upto a distance of 30m from the foundation trenches. (3.00 TO 4.50 M)
78	Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:With 20x20mm square bar
79	Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 500mm internal diameter
80	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level.Drilling of 350mm dia bore hole manually.
81	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia
82	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
83	Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
84	Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.
85	Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge.
86	Transportation of mini drilling Rig machine with camp equipage to site.
87	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well casing (CM) pipes of required dia, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia
88	Supply and fixing of nylon jali around the slotted pipes complete as required.
89	Supply of submersible pump of make KSB 5.0 HP with control panel, support wire etc. complete.
90	Providing 3 core 2.5 sqmm PVC insulated copper conductor submersible cable.(from pump panel to submersible pump)
91	Providing and fixing 65mm dia G.I. Pipe complete with fitting and clamps including cutting and making good the wall etc. (from submersible pump to ground level)
92	Providing and fixing 65 mm dia. brass gate valve with CI wheel of approved quality.
93	Supply and fixing of tube well accessories i.e. well cap, clips, clamps, etc. to complete the job in all respect.
94	Fixing, testing and commissioning for erection and lowering of submersible pump, 65mm dia GI column pipe, 3 core 2.5 sqmm submersible copper cable upto the control panel, supporting clamps, cable clips pressure gauge, connection line and all other accessories required for the proper completion of the work.
95	Testing and development of tube well.
96	Supply of MS grill of a approved quality and drawing made of flat iron not bigger then 20 x 4mm size including supply of materials fabrication labour T&P and also one coat of red oxide paint complete in all respect as per direction of Engineer in chrage for proper completion of work at site.
97	Supply of Fixing ofApprovedMS Z-Section windows and ventilators excluding cost of glass panes but including supply of all materials its fabrication nuts and bolts,hole fast for proper completion of work as per direction of engineer in charge and also including cost of handle stays rod etc.and one coat of red oxide paint complete in the respectsite of work.
98	Supply of Fixing of MS angle Iron door,window ventilation frame made of approved MS angle Iron wrought to required from including drilling hole welding and recetting where necessary and also including supply of all material such as steel hinges required size nut bolts etc and also including all taxes wastage and one coat of red oxide paint complete in all respect as per direction of Engineer in charge for proper completion of work at site of work.( 40 x 40 x 5 mm )
99	25 mm thick 1:2:4 plain cement concrete floor with cement approved coarse sand and 20mm graded approved stone laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio 5:1 as specified over and including 8 cm thick base concrete consisting of cement fine sand 1.25 fineness modulus and 4 cm gauge approved stone ballast in ratio 1:4:8 and removing any overlapping mortar at the joints of the panels if any giving them a uniform finish including supply of all material labour and T&P etc.required for proper completion of the work.
100	Providing & fixing white vitreous china pedastal type water closet (European type) with seat and lid, 10litre white low level PVC flushing cistren including flush pipe with mannualy controlled device(Handle lever)conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.W.C. pan with ISI marked white solid plastic seat and lid.
101	Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests flush pipe and over flow arrangement.
102	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Flat back wash basin size 630x 450 mm with a single 15 mm C.P. brass pillar tap.
103	Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.32 mm dia (for wash basin)
104	Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.40 mm dia(for sink and urinal)
105	Providing & Fixing 600 x 450 mm bevelled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
106	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.
107	Providing and fixing of 15 mm nominal dia CP brass/Health Fuccet of standard design and approved make including flexible tube upto 1.0 m long etc complete.
108	Providing and fixing of Two way 15 mm nominal bore CP brass bib cock of standard design and approved make etc complete.
109	Providing & fixing white vitreous china flat back halfstallUrinalof 580x380x350 mm with white PVC automatic flushing cistern with fittings standard size CP brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in CP brass including painting of fittings and brackets cutting & making good the walls & floors wherever required. Range of two half stall urinals with 5 liter P.V.C. automatic flushing cistern.
110	Providing & fixing white vitreous china flat back halfstallUrinalof 580x380x350 mm with white PVC automatic flushing cistern with fittings standard size CP brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in CP brass including painting of fittings and brackets cutting & making good the walls & floors wherever required. Range of three half stall urinals with 10 liter PVC automatic flushing cistern.
111	Providing & fixingsalem stainless steel AISI 304(18/8) kitchen sink without drain board asper IS : 13983 with C. I. brackets and stainless steelplug 40 mm including painting of fitting and brackets cutting and making good the walls wherever required. 610 x 510 bowl depth 200 mm Soil, Waste, Vent and Rain Water pipes and fittings
112	Providing & fixing PVC pipes conforming to IS make working pressure 6 Kg/sqcm including testing labour T&P and all complete fitting. (RWP)110mm dia
113	Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring, lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls, floors and refilling the trenches as before but excluding supply and cost of other fIttlings such as elbow, bend, tee and y-tee including supply of al marerial labour and T&P required for proper completion of work.90mm dia
114	Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring, lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls, floors and refilling the trenches as before but excluding supply and cost of other fIttlings such as elbow, bend, tee and y-tee including supply of al marerial labour and T&P required for proper completion of work.110mm dia
115	Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring, lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls, floors and refilling the trenches as before but excluding supply and cost of other fIttlings such as elbow, bend, tee and y-tee including supply of al marerial labour and T&P required for proper completion of work. 160mm dia
116	Haunching of SWR pipe 160mm with pcc 1:2:4cement concrete ( 1 cement:2 coarse sand:4 stone grit) AR
117	Supply and fixing of UPVC S.W.R. pipe nahni trap size 100/75 mm, 110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali.
118	Supply and fixing of UPVC S.W.R. door bend confirming to IS : 14735.110 mm dia
119	Supply and fixing of UPVC S.W.R. plain bend confirming to IS : 14735.90 mm dia
120	Supply and fixing of UPVC S.W.R. plain bend confirming to IS : 14735.110 mm dia
121	Supply and fixing of UPVC S.W.R. plain tee confirming to IS : 14735.90x90x90 mm
122	Supply and fixing of UPVC S.W.R. plain tee confirming to IS : 14735.110x110x110 mm
123	Supply and fixing of UPVC S.W.R. Cowel confirming to IS : 14735.110 mm dia
124	Supply and fixing of UPVC S.W.R. Cowel confirming to IS : 14735.90 mmdia
125	Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.Concealed work including cutting chase and making good the wall etc.15mm nominal outer dia pipes
126	Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.Concealed work including cutting chase and making good the wall etc.20mm nominal outer dia pipes
127	Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.Concealed work including cutting chase and making good the wall etc.25mm nominal outer dia pipes
128	Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.Concealed work including cutting chase and making good the wall etc.32mm nominal outer dia pipes
129	Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge.Internal work exposed on wall.15mm nominal outer dia pipes
130	Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge.Internal work exposed on wall.20mm nominal outer dia pipes
131	Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge.Internal work exposed on wall.25mm nominal outer dia pipes
132	Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge.Internal work exposed on wall.32mm nominal outer dia pipes
133	Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge.Internal work exposed on wall.40mm nominal outer dia pipes
134	Providing, fixing G. I. pipes complete with G. I. fittings and clamps including cutting and making good the walls etc. (internal work) - (Exposed on wall)32mm dia nominal bore
135	Providing, fixing G. I. pipes complete with G. I. fittings and clamps including cutting and making good the walls etc. (internal work) - (Exposed on wall)40mm dia nominal bore
136	Providing & fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end)20 mm nominal bore
137	Providing & fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end)25 mm nominal bore
138	Providing & fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end)32 mm nominal bore
139	Providing & fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end)40 mm nominal bore
140	Providing & fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end)50 mm nominal bore
141	Providing and fixing ball valve (brass) of approved quality complete. (High or low pressure with plastic floats).25 mm nominal bore
142	Providing& fixing 15 mm nominal bore 45 cm long unplasticised PVC connection pipe with brass unions.
143	Providing & fixing 15 mm nominal bore CP brass bib cock of approved quality conformingtoIS 8931.
144	Providing and fixing 15 mm nominal bore C.P brass long nose bib cock of approved qualityconforming to IS standards and weighing not lessthan 810 gms.
145	Providing & fixing 15 mm nominal bore C.P brass angle valve for basin mixer and geyser points of approved quality conformingto IS8931.
146	Providing & fixing gun metal gate valve with C.I. wheel of approved quality (screwed end).50 mm nominal bore
147	Constructing brick masonry chamber 600 x 600x 750 mm inside with F.P.S. brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Sluice Valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20 mm nominal size); necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1 : 3 (1 cement : 3 coarsesand ) 12mmthick finished with a floating coat of neat cementcomplete as per standarddesign
148	Excavating trenches in all kind of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m.Up to 1.50 m depthPipes 80 mm to 300 mmdiameter
149	Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before but Including supply and cost of other fIttlings such as elbow,bend,tee and y-tee including supply of al marerial labour and T&P.Required for proper completion of work110 mm. dia. Pipes
150	Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before but Including supply and cost of other fIttlings such as elbow,bend,tee and y-tee including supply of al marerial labour and T&P.Required for proper completion of work.160 mm. dia. Pipes
151	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 gradded storne aggregate 40 mm nominal size) all round SW pipe including bed concrete as per standard design.110 mm. dia. Pipes
152	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 gradded storne aggregate 40 mm nominal size) all round SW pipe including bed concrete as per standard design.160 mm. dia. Pipes
153	Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Inside size 90 x 80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
154	Extra for depth formanhole with F.P.S. brickssize 90 X 80 cm
155	Providing M.S. foot rests including fixinginmanholes with 202010 cm cementconcreteblocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as perstandard design : with 20 x 20 mm square bar
156	Providing and fixing square mouth S.W. Gully trapgrade `A\" complete with C.I. gratingbrickmasonry chamber with F.P.S bricks and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design180 x 150 mm. size P type
157	Providing & fixing viterous china toilet paper holder.
158	Providing and fixing PTMT Liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms
159	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.75 mm dia pipe
160	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm dia pipe
161	Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.
162	Providing and filling sand of grading zone V or coarser grade alround the G.I. pipes in external work.50 mm. Diameter pipe
163	Painting G.I. Pipes & fittings with two coats of anti-corrosive bitumastic paint of approved quality50 mm. Diameter pipe
164	Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed withstiffmixture of cement mortar in the proportion of 1:2 (1cement : 2 finesand) includingtestingof joints etc. complete.300 mm.dia. RCCPipes
165	Constructing brick masonaryroadgully chamber 50 x 45 x 60cm with F.P.S. brick in cement mortar 1 : 4 (1 cement : 4 coarse sand) including 500 x 450 mm precastRCChorizontal grating withframecompleteas per standard design.
166	Constructing brick masonaryroadgully chamber 110x50x77.5 cm with F.P.S. brick in cement mortar 1 : 4 (1 cement : 4 coarse sand) including 500 x 450 mmprecastRCChorizontal grating with frame and verticalgrating complete as per standard design.
167	Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
168	Providing and fixing of white vitreous china urinal partition for half stall urinals. (Parryware C0571 or equivalent)
169	Providing & fixing of hand lever operated forged brass full way ball valve type isolating valve having screwed ends tested to a pressure of 15 kg/sqcm complete. (Make : CIM) 15 mm nominal bore
170	Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg).
171	Providing and fixing soil, waste and vent pipes : 75mm diameter : Sand cast iron S&S pipe as per IS: 1729
172	25mm thick 1:2:4 cement concrete floor with cement approved coarse sand and 2 cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified over and excluding 8cm local sand and brick ballast 4cm guage in the proportion of 1:4:8 and removing any overlapping mortar at the joints of panels if any giving them a uniform finish including supply of all materials labour T & P etc required for proper completion of the work.
173	Providing & laying of rubber moulded interlocking concrete block pavements having thickness 80mm including levelling & dressing of surface to required level & slope spreading & moisting 30m thick local sand on bed filling joints with local sand etc. for proper completion of the work as per drawings & technical specification Clause 1504
174	Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/ IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 50 mm Dia
175	Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/ IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 80 mm Dia
176	Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/ IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm Dia
177	Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/ IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm Dia
178	Providing laying, testing & commissioning of \"C\" class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 NB
179	Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal /Stainless Steel cap and chain as required : Single headed Gun Metal
180	Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 150 mm Dia
181	Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 50 mm Dia
182	Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm Dia
183	Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm Dia
184	Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm Dia
185	Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80 mm Dia
186	Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm Dia
187	Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.30 Meter
188	Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: Gun Metal
189	Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Gun Metal
190	Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :3 way-150 mm dia M.S. Pipe
191	Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 100 mm Dia
192	Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 mm Dia
193	Providing & fixing air release made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height, with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metalwheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. (DSR E&M-2022)
194	Providing & fixing pressure switch in MS pipe line including connection etc as required. (DSR E&M-2022)
195	Constructing brick masonry chamber 900 x 900 x 1000 mm inside with F.P.S. brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Sluice Valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20mm nominal size);necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cementcomplete as per standard design (DSR Civil-2021)
196	Providing and placing on terrace (at all floor levels) polyethylene water storage tank. IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
197	Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-\"F\" insulation, conforming to IS-325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered with anti vibration pads. Discharge : 2280 lpm,Head : 56 meter
198	Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, completein all respects, as required : (Diesel Driven Pump)Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.Discharge : 2280 lpm,Head : 56 meter
199	Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-\"F\" insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. Discharge : 180 lpm,Head : 56 meter
200	Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-\"F\" insulation, conforming to IS-325. M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.Discharge : 450 lpm,Head : 35 meter
201	Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required : Incomer : 400A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital Voltmeter 0-500V with selector switch Digital Ammeter (0-400A) with selector swtich & CTs etc. LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Bus Bar : Set of copper bus bar 500 AMP . Outgoings : Outgoings : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps Main Fire Pump 125 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 60 HP pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation-2sets Jockey Pump 63 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local / remote, auto / manual / OFF operation.- 2 sets Diesel Engine Control Control of diesel engine comprising - Automatic/manual selector switch and 3 attempts starting device timer and relays as required, push buttons, start/stop in manual mode indicating lamp for high/low lub. Oil pressure, high water temp and engine on indication. Battery charger suitable for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC Voltmeter and 0-20 A DC ammeter all standard relays and accessories for automatic operation of diesel engine. System ControllerDesigning, supply, installation, testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, pressurization pump, terrace pump in sequence as per specification consisting of relays timers, sensors, annunciations window for fault indication, complete as per specification.
202	Supply andlayingofISI marked aluminiumconductor PVC / XLPE insulated armoured,served,sheathed cable 1100volts gradeat 750mmbelow ground level overacushion of 75 mm thick sand around & protected with brick onsides & top on surfacethecablerunshallbe fixed on M.S. clamps etc. of suitablesize completeinallrespect. The armouring of the cable shall be properlyconnectedwith the earth conductor by clamps etc. 95 sqmm 3 1/2core
203	Supply and fixing brass nickle plated compression glands for PVC insulated armoured, served, sheathed cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connectedwith the earth conductor.95 sqmm 3 1/2core
204	Supply & fixing of plam or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connections etc. complete in all respects as per direction of Engineer-in-charge. 50 sq.mm.
205	Supply & fixing of plam or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connections etc. complete in all respects as per direction of Engineer-in-charge. 95 sq.mm.
206	S/Fof shocktreatmentchart ( prescribed under I.E.rules ) duly framed with glass and supported from back with hard board orsoft board with supply of all material labour T & P etc for proper completion of work.
207	Supply andlayingof 1800 mm x 900 mm x 12 mm thick chequered rubber mattingof tested quality.
208	Supply & fixing of fire extinguisher, ABC Type 6.00 kg. capacity(ISI Marked IS:15683 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.
209	Supply & fixing of CO2 type fire extinguisher,6.5 kg. capacity(ISI Marked IS:2878 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.
210	Supplying and fixing of Fire man axe.Make :- Agni Suraksha (ASES) or EQ
211	Providing/Fixing of Fire Hose cabinet box made out of 18 gauge MS sheet including two coats of post office red paint over one coat of primer with 4 mm, thick glass door in front painted “FIRE” in red luminous paint. The size of the box should be 750 mm X 600 mm X 250 mm size capable of accommodating a pair of hose with coupling and nozzle. The box should be floor mounted type with railway coach lock arrangement and lever for opening the door after breaking the glass complete.Make : Standard/Lifeguard or EQ.
212	Providing and fixing in position M.S. pipe sleeves (heavy class) of upto 300 mm longwith M.S. puddle flange in RCC beams / retaining wall and other structural members during the time of casting the same including hot dipped galvanization after fabrication and painting with two coats of anti corrosive paint over primer. (for the crossing of sprinkler pipes)65NB
213	Providing and fixing in position M.S. pipe sleeves (heavy class) of upto 300 mm longwith M.S. puddle flange in RCC beams / retaining wall and other structural members during the time of casting the same including hot dipped galvanization after fabrication and painting with two coats of anti corrosive paint over primer. (for the crossing of sprinkler pipes) 100NB
214	Providing and fixing in position M.S. pipe sleeves (heavy class) of upto 300 mm longwith M.S. puddle flange in RCC beams / retaining wall and other structural members during the time of casting the same including hot dipped galvanization after fabrication and painting with two coats of anti corrosive paint over primer. (for the crossing of sprinkler pipes) 150NB
215	Providing and fixing in position M.S. pipe flanged sleeves of 600 mm long (heavy class) with M.S. puddle flange fabricated out of 6 mm thick MS plate in RCC walls of water tanks / retaining walls during the time of casting the same including hot dipped galvanization after fabrication and painting with two coats of anti corrosive paint over primer.65NB
216	Providing and fixing in position M.S. pipe flanged sleeves of 600 mm long (heavy class) with M.S. puddle flange fabricated out of 6 mm thick MS plate in RCC walls of water tanks / retaining walls during the time of casting the same including hot dipped galvanization after fabrication and painting with two coats of anti corrosive paint over primer.100 NB
217	Providing and fixing in position M.S. pipe flanged sleeves of 600 mm long (heavy class) with M.S. puddle flange fabricated out of 6 mm thick MS plate in RCC walls of water tanks / retaining walls during the time of casting the same including hot dipped galvanization after fabrication and painting with two coats of anti corrosive paint over primer.150 NB
218	Supply, Installation, Testing and Commissioning of electronic siren with suitable audible range of 1 k.m. approximately 4 watt.complete in all respects. Make :- Agni Suraksha (ASES) or EQ.
219	Providing and fixing of self illuminated / auto glow \"EXIT\" signs printed on photoluminescentsheet containing self illuminated base chemical, of appropriate size not less than 400 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site.
220	Supply, installation, testing and commissioning of intelligent analog adderessble photo thermal detector complete withmounting base complete as required.
221	Supply, installation, testing and commissioning ofintelligent adderessble thermal detector with rate of rise cum fixed temprature thermistor complete with base as required.
222	Supply, installation, testing and commissioning of Adderessable Manual call pointcomplete as required.
223	Supply, installation, testing and commissioning of addressable horn cum strobe complete as required.
224	Supply, installation, testing and commissioning of response indicators on surface/recessed MS box having two LED metallic cover complewith all connectionsetc as required.
225	providing, installing, connecting, testing and commissioning of microprocessor based intelligent addressable Main Fire Alarm panel central processing unit with the following loop modules and capable of supporting not less than 240 device (including detectors) and minimum 120 detectors per loop and loop length upto 2 km, network communication card, minimum 320 character graphic / LCD display with touch screen or other key pad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit(230 +/- 5% V, 50 Htz) 48 hrs backup with 24 volt sealedmaintenance fre bateries with automatic charger. The Panel shall have facility to connect printer to print out log and and facility to have seamless integration with analog/digital voice evacuation system (and shall be be complete with all accessories. The panel shall be compatible for IBMS system with open protocol BAC net/Modbus over IP complete as per specifications 10 loop panel
226	Supply and fixing of following size medium class PVC conduit along with accessories in surface / reccess including cutting the wall and making good the same in case of reccessed conduit as required. 25 mm
227	Supplying, and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / reccessed, steel / PVC conduit as required.(DSR E&M-2022) Supplying, and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / reccessed, steel / PVC conduit as required. 2 x 1.5 Sqmm
228	Supply, installation, testing and commissioning of Talk back slave station in surface/recess suitable for operation om simplex mode complete with PTT knob and speaker / microphone enclosed in a MS (16 SWG) / ABS box with break glass in front etccomplete as required.
229	Wiring point for light with 1.5 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in PVC conduit with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthing wire drawn inside the conduitpartly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with modular typeswitch & ceiling rose / angle / batten holder on 3 mm thick phenolic laminated backelite sheet etc complete in all respects as directed, including matching color wash
230	Wiring point for fan /fresh air fan (light duty exhaust fan) with 1.5 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduitwith modular typeswitch, G.P. Box & ceiling rose on 3 mm thick phenolic laminated backelite sheet etc complete in all respects as directed, including matching color wash.
231	Wiring point for plug 1.5 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduitwith modular typeswitch & socket etc, complete in all respect including matching colour wash.
232	Wiring point for call bellwith 1.5 sqmm.FRLSH PVC insulated multistrand single core copper condutor cable in PVC conduitpipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulated multistrand copper earth contunity wire drawn inside the conduit withmodular type bell push or 2 pin socket etc complete in all respects including matching color wash
233	Wiring point for HPMV/sodium vapour lamp with 1.5 sqmm FR PVC insulated multistrand single core copper conductor cable in PVC conduit partially concealed in wall & partly laid in slab along with the reinforcement before concreting complete with 1.5 sq mm FR P.V.C. insulated multistrand single core Copper Conductor cable as earth wire and 15-A piano type switches etc. complete in all respect as directed including maching colour wash.
234	Add for light / fan points with modular type switches in place of piano type switches
235	Add for plug point with modular switch & socket in place of piano type switch & socket
236	Add for call bell point with modular type bell push in place of piano type bell push
237	Add for HPMV/Exhaust fan point with modular type switch in place of piano type switch.
238	Supply & fixing of power plug with 20A/250 volts flush type modular switch and 5 pin 20 A/250 volts flush type universal modular socket on concealed MS box including supply of all material, labour T&P etc. required for proper completion of the work
239	S/F of sheet steel enclosure surface / flush mounting fitted with 20 amp 2 pin and earth metal clad scraping earth plug and socket complete. (for AC etc)
240	Supply & fixingof 20 amp. SP MCB (10 KA) (for AC etc)
241	Supply & wiring of sub main with FR P.V.C. insulated 1100 volts grade single core copper conductor cable in heavy gauge rigid steel coduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting, including matching colour wash etc complete in all respects. 4 x 16 sq. mm. with 2 no 10 SWG copper earth continuity wire, in 40 mm dia conduit.
242	Supply & wiring of sub main with FR P.V.C. insulated 1100 volts grade single core copper conductor cable in heavy gauge P.V.C. coduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete with FR PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. 2 x 2.5 sq. mm. with 1 x 1.5 sq.mm. earth wirein 20 mm dia conduit.
243	Supply & wiring of sub main with FR P.V.C. insulated 1100 volts grade single core copper conductor cable in heavy gauge P.V.C. coduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete with FR PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. 2 x 4 sq. mm. with 1 x 2.5 sq.mm. earth wire in 20 mm dia conduit.
244	Supply & wiring of sub main with FR P.V.C. insulated 1100 volts grade single core copper conductor cable in heavy gauge P.V.C. coduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete with FR PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. 2 x 6 sq. mm. with 1 x 4 sq.mm. earth wire in 25 mm dia conduit.
245	Supply & wiring of sub main with FR P.V.C. insulated 1100 volts grade single core copper conductor cable in heavy gauge P.V.C. coduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete with FR PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. 4 x 6 sq. mm. with 2 x 4 sq.mm. earth wire in 32 mm dia conduit.
246	Supply & wiring of sub main with FR P.V.C. insulated 1100 volts grade single core copper conductor cable in heavy gauge P.V.C. coduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete with FR PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. 4 x 10 sq. mm. with 2 x 6 sq.mm. earth wirein 32 mm dia conduit.
247	Supply and fixing and concealing of PVC conduit pipe with ISI mark embossed and with PVC accessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin/adhesive to make the complete piping rigid, plastering with cement sand mortar finished to the level with matching colour wash including cost of all material labour and T&P etc. required for proper completion of the work as per directions and to the satisfaction of Engineer in charge. (for Telephone / Television / circuits) 20 mm dia. conduit (2 mm thick)
248	Supply and fixing and concealing of PVC conduit pipe with ISI mark embossed and with PVC accessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin/adhesive to make the complete piping rigid, plastering with cement sand mortar finished to the level with matching colour wash including cost of all material labour and T&P etc. required for proper completion of the work as per directions and to the satisfaction of Engineer in charge. (for Telephone / Television / circuits) 25 mm dia. conduit (2 mm thick)
249	Supply and fixing and concealing of PVC conduit pipe with ISI mark embossed and with PVC accessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin/adhesive to make the complete piping rigid, plastering with cement sand mortar finished to the level with matching colour wash including cost of all material labour and T&P etc. required for proper completion of the work as per directions and to the satisfaction of Engineer in charge. (for Telephone / Television / circuits) 32 mm dia. conduit
250	S/F of surface/flush mounting TPN distribution board with additional metal door and without MCBcompletein all respect as directed at site by Engineer-in-charge. (Cat-A)6 WAYS
251	S/F of surface/flush mounting TPN distribution board with additional metal door and without MCBcompletein all respect as directed at site by Engineer-in-charge. (Cat-A) 8 WAYS
252	Supply & fixingof Single Pole MCB Blanking plate Cat-A
253	Supply & fixingof 6/10/16/20/25/32 amp. SP MCB (10 KA) Cat-A
254	S/F of 25 amp FP MCB(10 KA) Cat-A
255	S/F of 40 amp FP MCB (10 K.A.)Cat-A
256	S/F of 63 amp FP MCB (10 K.A.)
257	Supply Fixing and making commection of 30 MA E.L.C.B. (Earth leakage circuit breaker) of din/R.C.C.B. rail mounting complete in all respects as per directionandsatisfaction of engineer-in-charge. 25 Amp 4 Pole
258	Supply Fixing and making commection of 30 MA E.L.C.B. (Earth leakage circuit breaker) of din/R.C.C.B. rail mounting complete in all respects as per directionandsatisfaction of engineer-in-charge. 40 Amp 4 Pole
259	Supply Fixing and making commection of 30 MA E.L.C.B. (Earth leakage circuit breaker) of din/R.C.C.B. rail mounting complete in all respects as per directionandsatisfaction of engineer-in-charge. 63 Amp 4 Pole
260	Supply and burying of 600mm x 600 mmx6mm G.I. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm G.I.pipe and funnel for watering and two earthing leads of No.8to10SWG G.I.wire in 15mm diaG.I. pipe upto switch board (from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm. square C.I. frame with hinged cover, masonary housing, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects.
261	Supplying & Layingof 25mm x 3mm. G.I. strip for earthing purpose as required complete in all respects.
262	Supply andlayingofISI marked aluminiumconductor PVC / XLPE insulated armoured,served,sheathed cable 1100volts gradeat 750mmbelow ground level overacushion of 75 mm thick sand around & protected with brick onsides & top on surfacethecablerunshallbe fixed on M.S. clamps etc. of suitablesize completeinallrespect. The armouring of the cable shall be properlyconnectedwith the earth conductor by clamps etc. 10 sqmm4core
263	Supply andlayingofISI marked aluminiumconductor PVC / XLPE insulated armoured,served,sheathed cable 1100volts gradeat 750mmbelow ground level overacushion of 75 mm thick sand around & protected with brick onsides & top on surfacethecablerunshallbe fixed on M.S. clamps etc. of suitablesize completeinallrespect. The armouring of the cable shall be properlyconnectedwith the earth conductor by clamps etc. 16 sqmm 4 core
264	Supply andlayingofISI marked aluminiumconductor PVC / XLPE insulated armoured,served,sheathed cable 1100volts gradeat 750mmbelow ground level overacushion of 75 mm thick sand around & protected with brick onsides & top on surfacethecablerunshallbe fixed on M.S. clamps etc. of suitablesize completeinallrespect. The armouring of the cable shall be properlyconnectedwith the earth conductor by clamps etc. 185 sqmm 3 1/2core
265	Supply and fixing brass nickle plated compression glands for PVC insulated armoured, served, sheathed cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connectedwith the earth conductor.10 sqmm 4core
266	Supply and fixing brass nickle plated compression glands for PVC insulated armoured, served, sheathed cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connectedwith the earth conductor.16 sqmm 4core
267	Supply and fixing brass nickle plated compression glands for PVC insulated armoured, served, sheathed cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connectedwith the earth conductor.185 sqmm 3 1/2core
268	Supply & fixing of plam or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connections etc. complete in all respects as per direction of Engineer-in-charge.10 sq.mm.
269	Supply & fixing of plam or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connections etc. complete in all respects as per direction of Engineer-in-charge.16 sq.mm.
270	Supply & fixing of plam or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connections etc. complete in all respects as per direction of Engineer-in-charge.95 sq.mm.
271	Supply & fixing of plam or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connections etc. complete in all respects as per direction of Engineer-in-charge.185 sq.mm.
272	S/F of recess/surface/pendent mounted 10 to 15 watt LED down lighter having powder coated die cast aluminium housing with heat sink, difuser / refelector and driver set complete in all respect Category AAA
273	S/F of 55 watt indoor recess mounting LED square fitting for Armstron ceiling having powder coated die cast aluminium housing body with extended heat sink, difuser of polycarbonate material and driver set complete in all respectCategory AA
274	S/F of LED Tube Light with batten suitable for up to 1x22 watt LED tube light fitting including tube on surface complete in all respect. Category AAA
275	S/F of LED Tube Light with batten suitable for up to 2x22 watt LED tube light fitting including tube on surface complete in all respect. Category AAA
276	S/F of single LED light wall bracket 3 to 6 Watt on matching M.D.F.E.G. Board base etc complete in all respect. Category AAA
277	S/F ofLED street light fitting having die cast aluminium body and diffuser with driver set suitable for 52 watt to 72 watt confirming to IP 66 protection complete in all respect.Category AAA
278	Supply of ceiling fan with fan motor of AC permanent insulation, capacitor rating conforming BEE 5 star rating and IS : 374/79 and also comply with IS:1709/1984 with latest amendment the rated voltage 220/240 volts, 50 HZ single phase AC, the fan assembled should consists of down rod, blades, shackel canopies etc and with double ball bearing system.BEE 5 star rating - 1200 mm sweep
279	Erection and testing of ceiling fan and regulator for room height upto 3.50 meter including supply of 3 mm thick G.I. Rod 19 mm dia. Duly painted, complete in all respect.
280	Add extra to above item for 15 cm or part thereof for room height from 3.50 to 5.00 meter.
281	Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts nuts and washers etc complete in all respects.
282	Supply and fixing of 16 gauge MS drum duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect.
283	S/F of hexagonal fan box with hexagonal side of approx. 80 mm.in lengthfabricatedfrom 16 SWG M.S. sheet incorporating with10 mm. dia. M.S. round bar duly bent for supporting fan hanger duly painted with redoxideand screwingarrangementwithwiringconduit laid in the R.C.C.roofbeforeconcreting along with supply of all materials,labour, T&P etc. for proper completion of work.
284	Supply & fixing ofelectronic Fanreulator, 120-280 V, ISI marked, on the existing switch board including making connections, required material,labour T/P etc. for proper completion of work to the satisfaction of Engineer of work.
285	S/F of doorchimeonPolishedM.D.F.E.G. board includingmakingconnectionsetc. complete in all respects.
286	S/F of danger board fabricated from 10 gauge M.S. sheet as per E/I rules.
287	S/Fof shocktreatmentchart ( prescribed under I.E.rules ) duly framed with glass and supported from back with hard board orsoft board with supply of all material labour T & P etc for proper completion of work.
288	Supply andlayingof 1800 mm x 900 mm x 12 mm thick chequered rubber mattingof tested quality.
289	Supply & Errecetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN MCCB\"s (Four Pole 36 KA with thermal magnatic release)Switches Complete and instrument chamber etc.complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters (KVA, P.F, KW etc) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB\"s shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc.The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubicle type switch board shall be of cat A & B Only.Incomer : 400 Amp MCCB-1 No Outgoings :200 Amp MCCB, 100 Amp MCCB, 63 Amp MCCB or as required Cat-B Panel Cubical Type
290	Supplying and fixing following size / modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75 mmX75 mm)
291	Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 1 or 2 Module (75 mmX75 mm)
292	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet
293	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet
294	Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 pair
295	Supplying and drawing Co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
296	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 120 mm dia (OD-120 mm & ID-103 mm nominal)
297	Providing, fixing, connecting & testingof Krone box (Telephone Tag Block) in athermoplastic, IP 65 (weather proof) enclosure, internally embedded gasket, anti corrosive, insulated and shock proof with provision for cable through IP 65 glands complete in all respects. (Make : Hensel) 10 pair krone (Hensel - KG 9001 - size 136253115 mm)
298	Providing, laying, connecting, testing& commissioning of multi-core telephone armoured cables of conductor size 0.5 sq.mm. annealed tinned electrolitic grade copper, PVC insulated, twisted pairs bunched together, over all PVC sheathed, GI strip or wire armouring laid on existing cable tray or along the wall or laidin pipes or in trenches including excavationofcabletrench, sand filling covering with bricks andback filling complete as required. 10 pair
299	Providing & Fixing of modular plate type white RJ 45 Data outlet / information outlets ETL verified to meet or exceed TIA / EIA category 5e requirements, universal wiring label permitting to either T568A or T568B, UL listed,for computer networkingcomplete in all respect with cover plate, grid plate, screws, MS box, etc with connections as required.1 nos. RJ 45 Data Outlet
300	Providing, drawing, connecting and testing of enhanced category 4 pair LAN (local area network) cable, UL and CUL listed, in existing MS/PVC conduit or floor raceways including connections etc as required complete in all respects. (Make : AMP / Systemax) CAT-5 network cable
301	Supplyof AC 230/250 Volts, 50 Hz 55w 1400 rpm exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required.-Make: Havells-STANDARD -Refresh Air-SPS
302	Supply of 400 mmsweepAC 230/250 volts, 50 HZ wall mounting revolving fan with brackets etc. complete (Make : Bajaj / crompton / havells)
303	Supply & Installation of Split Direct Expansion Air Conditioners Suitable for Operation on A/C supply single phase 50HZ 230 Volts with hermetically sealed compressor with air cooled condenser, moter capacitor and start run capacitor, relay and over load protector internal unit with one indoor and outdoor unit. The condenser unit will be placed out side the room on the terrace to avoid noise including standard length of suitable size copper tubing covered with insulation tube (high wall choreded/ cordless) suitable capacity 3 core sheathed/ PVC copper cable and a battery operated wireless remote unit.(2.00 tonne 5 star Rated)
304	Supply & Installation of Split Direct Expansion Air Conditioners Suitable for Operation on A/C supply single phase 50HZ 230 Volts with hermetically sealed compressor with air cooled condenser, moter capacitor and start run capacitor, relay and over load protector internal unit with one indoor and outdoor unit. The condenser unit will be placed out side the room on the terrace to avoid noise including standard length of suitable size copper tubing covered with insulation tube (high wall choreded/ cordless) suitable capacity 3 core sheathed/ PVC copper cable and a battery operated wireless remote unit.(1.50 tonne 5 star Rated)
305	Supply and Installation of V-Guard/Microtek brand make as equivalent stablizers which suitable for split A.C.

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Uttar Pradesh Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Media Centre At District Chitrakoot, Chitrakoot-Uttar Pradesh

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Media Centre At District Chitrakoot, Chitrakoot-Uttar Pradesh

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us