Military Engineer Services-MES has published Tender For Addition Alteration And Upgradation Of Old Electrical Wiring And Power Points In Bldg No P-35(Adm Block) Of Bde Camp, Spl Repair To Bldg No P-15 (O1 To 04) Or Md Accn At Sanga Enclave Of Hq Sampark, Addn Altn Of Old Electric Wiring And Con. Submission Date for this Tender is 11-11-2023. Building Work Tenders in Pathankot Punjab. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 04-Nov-2023 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 11-11-2023 |
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 2 | Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 3 | Taking down shutters of any descriptionnot exc. 1 Sqm each, complete all as specified & directed. |
| 4 | Taking down shutters of any description exc. 1 sqm and not exc. 2 Sqm each, complete all as specified & directed. |
| 5 | Refixing in same opening shutters of any description exc 1 sq. m and n exc 2 sq. m eachincludes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed. |
| 6 | Demolition of brick work or stone / bouldermasonry includingall quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed. |
| 7 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed. |
| 8 | Demolition ofreinforced cement concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed. |
| 9 | Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed. |
| 10 | Dismantling of water tank exc. 500 Litre but not exc. 1000 Litre capacity complete all as specified and directed. |
| 11 | Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for laying of cable etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed. |
| 12 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed. |
| 13 | M&L for dry sand cushioning for UG cable in trenches including spreading levelling and hand paning and consolidating complete all as specified and directed. |
| 14 | Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. |
| 15 | M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed |
| 16 | M & L for providing plain cementconcrete type C-2, 1:3:6, (using 20 mm graded stone aggregate), as infilling of pressed steel door frames/chowkats complete all as specified and directed. |
| 17 | M & L for providing plain cement concrete, type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in sunken, filling and mass concrete complete all as specified and directed. |
| 18 | M & L for providing plain cement concrete, typeE-2, 1:5:10 (using 40 mm graded stone aggregate) as in sunken, filling and mass concrete complete all as specified and directed. |
| 19 | M & L for providing pre-cast cement concrete landing, cover slabs, chullah hoods, chajjas, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:4 complete all as specified and directed. |
| 20 | M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 21 | M & L for brick work with sub class ‘B’ old size bricks (EXCEPTBRICKS) straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed. NOTE: - OLD BRICKSOBTAINED FROM DEMOLITION SHALL BE USED UNDER THIS ITEM. |
| 22 | Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed. |
| 23 | S & F of solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed. |
| 24 | All as per item No 23 but wood grain printed PVC sheet used insteat of plain colour PVC sheet and edge will be painted to match with pinted sheet complete all as specified and directed. |
| 25 | S & F of 35mm thick 2ndclass hard wood (Sal/Hollock), glazed and skeleton shutters (factory made), open rebated and prepared to receive glass or gauge etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in clause 8.24 (a) of SSR Part-I, complete all as specified and directed. |
| 26 | All as per item No 25 but Partly panelled (bottom portion) and partly glazed or gauzed ( top Portion) suitable for fly proofing complete all as specified and directed. |
| 27 | 35mm thick factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified & directed. |
| 28 | S & F of 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawinggiven on MES schedule Part – II (2010) complete all as specified and directed. |
| 29 | All as per item no. 28 but wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading complete all as specified and directed. |
| 30 | S & F of 300 mm long (Length of bolt) brass sliding door bolt with sand or die cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified and directed. |
| 31 | S & F of 100 mm sizealuminium anodised Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 32 | S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed. |
| 33 | S & F of 300 mm mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed. |
| 34 | S & F of 125 mm long anodised aluminium handle, cast type complete all as specified and directed. |
| 35 | S & F of 150 mm long anodised aluminium handle, cast type complete all as specified and directed. |
| 36 | S & F of 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 37 | S & F of 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 38 | S & F of 140 mm size (Overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed. |
| 39 | S & F of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 40 | S & F of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed in repair with stainless steel wire staples complete all as specified and directed. |
| 41 | M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia securing with clips complete all as specified and directed. |
| 42 | S & F of steel work as as in tubular trusses or rectangular hollow section including special etct. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed. |
| 43 | S & F of rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors etc. to be prepared for hanging orsteel hanging door fitting and also fastening complete all as specified and directed. |
| 44 | S & F of factory made box type steel windows comprised of tubular frame and shutters made out of 1.25mm thick MS sheet tube with double side shutters (Wire Gauged shutter and Glazed Shutter), side hung shutters with MS handles and MS stays dovetailed or welded including 02 nos MS Tower Bolt 150mm long for each leaf, 8 mm square guard bars at spacing as shown in drawings, MS flat iron frame work, MS hinges, tarred hold fast,PCC 1:2:4 type B1 as in bed of hold fast, 01 No. per leaf of stopper of 100mm size, one coat of red oxide zinc chrome primer etc, complete all as specified and shown as drawing No. CEPZ/TD-354/09 sheet 1/3 to 3/3. NOTE : a). Wire cloth and Sheet glass shall be measured and paid seprately under respective items. b). Rate of both type of shutters is inclusive in the quoted rate. |
| 45 | S & F of 1.25 mm thick mild steel plain black sheet in hearth, covering of door shutters, covering to door chowkhats (frames), chullah hoods, water tank, water troughs and funnels etc., cut to size, edges beaded if directed, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel members etc. with plain 40 mm lap joints with welded / rebated seams including bending, turning up, mitred angles, stopped ends, outlets etc. as required complete all as specified and directed. |
| 46 | S & F of pressed steel frames of size 125mmx60mm made of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate., complete all as specified & directed.NOTE : PCC for filling of hollow portion shall be measured and paid for separately. |
| 47 | S & F of pressed steel frames of size 105 mmx60mm made of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate., complete all as specified & directed. NOTE : PCC for filling of hollow portion shall be measured and paid for separately. |
| 48 | S & F of Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed .NOTE:- Corrugated shape of sheet shall be approved by GE |
| 49 | M & L for 18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber framed work as in cup board shutters, shelves etc., complete all as specified & directed. complete all as specified and directed. |
| 50 | M & L for 15 – 18 mm thick machine cut kota stone slab flooring, of size not less than 580x580mm, as per sample kept in GEs office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, grinding and polishing to achieve mirror finish laid over and including 15mm screed layer in cement mortar 1:3, complete all as specified. |
| 51 | M & L for 15 – 18 mm thick Machine cut kota stone slab, as per sample kept in GEs office as in vertical surfaces such as skirting/dado etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, grinding and polishing, laid over and including 10mm thick renderingin cement mortar 1:4, complete all as specified & directed. |
| 52 | M & L for 75 mm thick cement concrete 1:3:6 type C-2, using 40 mm graded stone aggregate as in sub base of floor/hard standing complete all as specified and directed. |
| 53 | M & L for 75 mm thick cement concrete 1:3:6 type C-1, using 20 mm graded stone aggregate as in plinth protection laid to slop of 1:12, finished surface even and fair without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm thick joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed. |
| 54 | M & L for providing 25 mm thick cement concrete 1:2:4 type B-0 (using 12.50 mm thick graded stone aggregate) as in roof padding even and fair complete all as specified and directed. |
| 55 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, and brushing neat cement slurry with 3.0Kg of cement per square metre, complete all as specifed & directed. |
| 56 | M & L for 15 to 18 mm thick granite (of any type and shade) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4)including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including necessary cutting, grinding, rubbing, polishing rounding to exposed edgesand laid over20 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes finished even and rough complete all as specified and directed. |
| 57 | M & L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.NOTE: - SCREED SHALL BE MEASURED AND PAID SEPARATELY. |
| 58 | M & L for Glazed ceramic coloured tiles in vertical surface 450x300x 7 mm thick , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. NOTE: - RENDERING SHALL BE MEASURED AND PAID SEPARATELY. |
| 59 | M & L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete NOTE: - SCREED SHALL BE MEASURED AND PAID SEPARATELY. |
| 60 | M & L Non - skid Ceramic joint free colouredtiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in skirting/dado etc. set and jointed in neat cement slurry and pointed in white orcoloured cement to match complete all as specified and directed. NOTE: - RENDERING SHALL BE MEASURED AND PAID SEPARATELY. |
| 61 | M & L for precast designer coloured heavy duty full body paving tiles (factory made)of size 300mmx300mm x 10mm, top layer glazed made in any type of cement and pigment, in required patterns as approved by GE in floor etcset & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 10mm thick screed layer in cement mortar 1:4, complete all as specified & directed. |
| 62 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. |
| 63 | M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extracement)complete all as specified and directed. |
| 64 | M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth (without using extracement)complete all as specified and directed. |
| 65 | M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 a finished even and fair and mixing of water proofing compound as per manufacturer’s instructions complete all as specified and directed. NOTE: - (i)WATER PROOFING COMPOUNDSHALL BE MEASURED AND PAID SEPARATELY. |
| 66 | M & L for 10 mm thick rendering on ceiling /rooj projecation chhajja side finsof concrete surfaces with cement mortar 1:3 finished even and smooth (without using extracement)complete all as specified and directed. |
| 67 | M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes finished even and rough complete all as specified and directed. |
| 68 | M & L for 10 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:4 on vertical surfaces of wall finished even and rough suitable for laying wall tiles complete all as specified and directed. |
| 69 | Taking down cementplaster and decayed concrete of any description,upto triple storey of building from roof projection, chajjas etc and making good the decayed portion with cement mortar 1:3 mixed with integral water proofing compound orPCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate including necessary form work/scaffolding where ever required, rendering with 15 mm thickcement mortar 1:3, surface finished even and smooth without using extra cementusing integral water proofing compound as per manufacturer,s instructions , complete all as specified & directed. NOTE:-Integral water proofing compound shall be measured & paid seprately. |
| 70 | Hacking out old broken glass (any thickness, size, qualityor description) from wooden / metal frames, glazed with oil putty or fixed with beads including punching or drilling out old glazing pins / spring clips and providing and fixing new ones complete allas specified and directed. |
| 71 | S & F of 3 mm thick plain, ordinary quality sheet glass and glazing with oil putty or fixed with beads in square not exc. 0.5 sqm in each pane complete all as specified and directed. |
| 72 | S & F of 3 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane with oil putty or fixed with beads complete all as specified and directed. |
| 73 | M & L for complete removal of old finishes from walls by scrapping, rubbing down, with sand paper to have even and smooth surfaces and applying two coats ofcement base paint over one coat of water proofingprimer complete all as specified and directed. |
| 74 | M & L for preparation of newly plastered or un-plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 75 | M & Lfor preparation of old decorated plastered or unplastered surfaces of ceiling, cornices etc by brooming down or steel wire brushing downscrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots,and applying one coats of white wash complete all as specified and directed. |
| 76 | M & L for preparing newly plastered or previously untreated wall surfaces and applying two coats of cement base paint over one coat ofwater proof primer complete all as specified and directed. |
| 77 | M&L for preparation of old decorated plastered or unplastered surfaces of walls, cornices etc by brooming down or steel wire brushing downscrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, and applying one coats of cement base paint complete all as specified and directed. NOTE:- Bldg height upto 6 Mtr |
| 78 | M & L for preparing newly plastered or previously untreated wall surfaces and applying two coat of oil bound distemper over one coat of water proofprimer complete all as specified and directed. |
| 79 | M & L for preparing newly plastered or previously untreated wall surfaces and applying two coat of oil bound distemper complete all as specified and directed. |
| 80 | M & L for complete removal of old finishes from walls by scrapping, rubbing down, with sand paper to have even and smooth surfaces and applying two coats of oil bound distemperover one coat of birla wall care putty complete all as specified and directed. |
| 81 | M&L forapplying3mm thick of birla wall care putty including rubbing down the surface with sand paper after getting dried to obtain a smooth & even surface complete all as specified and directed. |
| 82 | M & L for complete removal of old finishes from walls by scrapping, rubbing down, with sand paper to have even and smooth surfaces and applying two coats of ‘Apex’ of Asian paint or ‘Weather coat’ of Berger Paints over one coat of primer complete all as specified and directed. |
| 83 | M&L for preparation of oldunpainted surface ofwall etc. and applying one coats of ‘Apex’ of Asian paint or ‘Weather coat’ of Berger Paintscomplete all as specified and directed. |
| 84 | M & L for preparing newly plastered or previously untreated wall surfaces and applying 3 mm thick Acrylic wall putty on wall surface complete all as specified and directed. |
| 85 | M&L for preparation of oldunpainted surface ofwall etc. and and applying 3 mm thick Acrylic wall putty on wall surface complete all as specified and directed. |
| 86 | M & L for preparation of new or previously untreated wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 87 | M & L for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 88 | M&L for preparation of old painted wood and wood based surfaces of any description not otherwise described over 10 cm width or girth including knotting and stopping and applying one coat of synthetic enamel paint (any tint/Shade) complete all as specified and directed. |
| 89 | M&L for preparation of old painted steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint (any tint/shade) complete all as specified and directed |
| 90 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes by using bleaching powder, hoisting if required,reconnecting and re-fixing in position of capacity exc. 500 & n. exc. 1000 ltr,making good for running of water from tank to inside of bldgs and writing of date of cleaningand due on by synthetic enamel paint on water tank, complete all as specified & directed. NOTE :- Cost of bleaching powder shall be deemed included in the quoted rate of this item. |
| 91 | S & F of 500 Litre capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) of specifications as per MES Schedule 2009, Part – I and hoisted, fixed in position complete all as specified and directed. |
| 92 | S & F of 1000 Litre capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) of specifications as per MES Schedule 2009, Part – I and hoisted, fixed in position complete all as specified and directed. |
| 93 | Taking up or down 15 mm bore steel water tubing and connection, including cleaning for refixing or removal to store complete all as specified and directed. |
| 94 | Taking up or down 20 mm bore steel water tubing and connection, including cleaning for refixing or removal to store complete all as specified and directed. |
| 95 | Taking up or down 25 mm bore steel water tubing and connection, including cleaning for refixing or removal to store complete all as specified and directed. |
| 96 | Fixing only 20 mm bore old steel water tubing and connection in new or old position to wall and ceiling or laid in floors jointing and testing of old retrieved serviceable galvanized mild steel water tubing with and including all fitting (such as bends, elbows, tees, short pieces, connectors, back nuts, deminishing pieces caps, plugs and union etc) complete all as specified and directed. NOTE: - OLD STEEL WATER TUBING OBTAINED FROM DISMANTLING SHALL BE USED UNDER THIS ITEM. |
| 97 | Fixing only 25 mm bore old steel water tubing and connection in new or old position to wall and ceiling or laid in floors jointing and testing of old retrieved serviceable galvanized mild steel water tubing with and including all fitting (such as bends, elbows, tees, short pieces, connectors, back nuts, deminishing pieces caps, plugs and union etc) complete all as specified and directed. NOTE: - OLD STEEL WATER TUBING OBTAINED FROM DISMANTLING SHALL BE USED UNDER THIS ITEM. |
| 98 | S&F 15mm nominal bore of pipe in walls, and ceiling or laid in floors, jointing and testing galvanised mild steel water tubing “medium grade” with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all asspecified and directed. |
| 99 | S&F 20 mm nominal bore of pipe in walls, and ceiling or laid in floors, jointing and testing galvanised mild steel water tubing “medium grade” with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all asspecified and directed. |
| 100 | S&F 15 mm nominal bore of unplasticised UPVC pipes of fixed complete to walls, ceilings or in floors etc., any type of pipe with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all asspecified and directed. |
| 101 | S&F 20 mm nominal bore of unplasticised UPVC pipes offixed complete to walls, ceilings or in floors etc., any type of pipe with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all asspecified and directed. |
| 102 | S&Fofbib taps, cast copper alloy with crutch or butterfly handle, screwed down, externally threaded having weight @ 0.40 Kg/Each, ISI marked with IS : 781, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed. |
| 103 | Cutting existing steel tubing for alterations or additions (Each cut measured) complete all as specified and directed. |
| 104 | S & F of 32 mm bore low density polyethylene pipes (LDPE) of pressure rating 6 Kgf per Sqcm and laid in complete to walls, ceilings or in floors etc.complete all as specified and directed. |
| 105 | S & F of 15 mm bore chromium plated,fancy type bib tap, cast copper alloy with capstan heads,screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 106 | S&F fancy type angular stop cock with flange, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, externally threaded,screwed both ends for iron pipe or for unions of 15mm bore complete all as specified and directed. |
| 107 | S&F in repair fancy type angular stop cock with flange, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, externally threaded,screwed both ends for iron pipe or for unions of 15mm bore complete all as specified and directed. |
| 108 | S&F of stop cock (valves),concealed type cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, externally threaded, having weight @ 0.40 Kg/Each, ISI certification marked with IS : 881, screwed both ends for iron pipe or for unions of 15mm bore complete all as specified and directed. |
| 109 | S&Fstop cock (valves), concealed type cast copper alloy, , screwed down, high pressure, with crutch or butterfly handle, externally threaded, having weight @ 0.75 Kg/Each, ISI certification marked with IS : 881, screwed both ends for iron pipe or for unions of 20 mm bore complete all as specified and directed. |
| 110 | S & F of20 mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed. |
| 111 | S&FSheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 112 | S&F glass corner shelf with bracket fixed with chromium plated brass screwsfix to wall with rawl plug and CP screws complete all as specified and directed.Make:- JAQUAR Cat Part No ACN-1173 or equivalent model in specified makes as approved by GE |
| 113 | S&F PVC mirror cabinet of size 16”x16” with napkin rail in ivory colour complete all as specified and directed. |
| 114 | S&F S&F stainless steel Hat and coat hooks solid body 175mm to 250mm complete all as specified and directed. |
| 115 | S & F in repairs 600 mm long PVC connection with two Nos. PTMT nuts internally threaded and PVC washer suitable for 15 mm bore pipe line complete all as specified and directed. |
| 116 | S & F of soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 117 | S&F Soap dish chromium plated of continential series, complete all specified and directed (Make : Jaquar Cat Part No. 1131 or equivalent in Marc/ Riviera). |
| 118 | S & F of chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union size 125 mm complete all as specified and directed. |
| 119 | S&F of wall mixer with provision for overhead shower with 65 mm long bend and wall flange non telephonic type chromium plated ,etc.complete all as specified and directed. Make:- PRAYAG Cat Part No BS-29 or equivalent model in specified makes as approved by GE |
| 120 | S&F in repair 25mm outer dia stainless steel decorative drapery rod (including necessary fittings) of thickness 20 gauge, for every 1 RM length provide 10 numbers stainless steel wings of 50mm dia and proportionate for part offwith stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod ar both ends, complete all as specified & directed. Note: The drapery rod shall be projected 150mm outer side from the closer opening of doors/windows. |
| 121 | S & F in repair20 mm dia brass chromium plated tubular towel rail "D" type 60 cm long between flanges, including one pair of fixing brackets complete all as specified and directed. |
| 122 | S & F of 15 mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered "HOT" or "COLD’ with long screwed shank and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 123 | S&F of stainless steel plate rack of size 900x750x250mm made out of AISI 304 stainless steel 0.63 mm thick having partitions as per sample kept in AGE office including brass/stainless steel screws for fixing of partitions, nuts, bolts, washers and fittings, complete all as specified & directed. |
| 124 | S&F of sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 405mm x 355mm x 178mm complete all as specified and directed. |
| 125 | S & F in repairs water closet vitreous china squatting pan ‘Orrisa’ pattern size 580 X 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, anti-syphonic pipe etc. with and including setting the trap and pan in lime concrete bedding (one lime, two sand or surkhi and 5 aggregate) minimum 150 mm thick alround and finished just below level of rim of pan to receive the floor finishes complete including making good floor complete all as specified and directed. |
| 126 | S & F of vitreous china, wash hand basin, flat back, white of size 580mmx450mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, chain and plug, porcelain stopper including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs, complete all as specified & directed |
| 127 | S & F of vitreous China, corner wash hand basin white of size 400mmx400mmx 125mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, PVC 32mm dia waste pipe, chain and plug including cutting for and pinning in ends of brackets or erecting stand, complete all as specified. |
| 128 | S & F in repairpolymer white (polypropylene Delrin and ABS) low level flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, flush pipe, brass screws, handle etc complete having BIS description mark with IS: 7231 with and including 32 mm bore PVC flush pipe of suitable length complete all as specified and directed. |
| 129 | S&F 600mmx450mm bevelled edge mirror of selected quality glass 4 mm thick, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 130 | S & F of 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint fixed to wall complete all as specified and directed. |
| 131 | S & F of 110 mm bore PVC (SWR) junction single, (Single ‘T’) equal or unequal with Oval access complete all as specified and directed. |
| 132 | S & F of 110 mm bore PVC (SWR) junction double, (Double ‘T’) equal or unequal complete all as specified and directed |
| 133 | S & F of 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed. |
| 134 | S & F of 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed. |
| 135 | S & F of 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint fixed to wall/floor complete all as specified and directed. |
| 136 | S & F of 75 mm bore PVC (SWR) bend any radius complete all as specified and directed. |
| 137 | S & F of 110 mm bore PVC (SWR) bend any radius complete all as specified and directed. |
| 138 | S & F of 110 mm bore PVC (SWR) branch piece,single (single Y) equal or unequal complete all as specified and directed |
| 139 | S & F of 110 mm bore PVC (SWR) Slottedvent cowl complete all as specified and directed |
| 140 | S & F of 75 mm bore PVC (SWR) Slottedvent cowl complete all as specified and directed |
| 141 | S&F in repair PVC grating square,150mm (Hing pattern and with or without hole. complete all as specified and directed. |
| 142 | S & F of 75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed. |
| 143 | M & L for cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipeafter they are laid and tested complete all as specified and directed. |
| 144 | Cleaning /clearing of sewage line (including manholes) 100mm to 150mm bore of any description , underground at any depth, removing any type of blockage including desilting,descaling and dechocking of darins as well as manholes and deposting the sludge in a pit (including digging of pit) not less than 100 M away from the site of cleaning and covering the sludge with layer of 2.50 cm thick layer of earth anf spraying unslacked lime on the pit and make line smothh functional complete all as specified and directed. |
| 145 | Cleaning of blocked WC including and upto first manhole manually and well flushing with clear water, making the seat functional including depositing the sludge in a pit (including digging of pit) not less than 100 meter away from site of cleaning and covering the deposited sludge with minimum 25cm thick layer of earth and spreading unslacked lime on the pit, complete all as specified & directed. |
| 146 | Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching, internal dia of pipe 150mm, complete all as specified & directed. |
| 147 | S & F of 150mm bore reinforced concrete pipe class NP-3 laid, jointed with collar in neat cement slurry complete all as specified and directed. |
| 148 | Water proofing treatment to sunken portion with 15mm thick rendering in cement mortar 1:3 using integral water prooofing compound both on floor and walls including preparation of surface by making free from all loose particles, surface cured and allowed to dry,apply a coat of Moisture Cured High Tensile Elastomeric Modified Poly Urethane based liquid membrance coatingas per manufacturers instructions both on floor as well on walls, sunken slab shall be laid to a slope of 1:40 outwards with 25mm dia PVC pipe spout projecting at least 45mm beyond out face of wall, complete all as specified & directed. Notes : a) PVC spout 25mm dia, PCC 1:4:8 type D2 and WC / EWC shall be measured and paid for separately under respective items. b) Ponding shall be done in sunken portion area by filling water which shall be kept there for one week. In case a slightest indication of seepage /leakage is noticed, the same shall be rectifird by grounting the effected area at no extra cost. Thereafter, ponding shallbe repeated till there is no indication of seepage/leakage. The arrangements of ponding to be included in quoted rates and nothing shall be admissible on this account. |
| 149 | Complete removal of the existing roof treatment of any description viz tarfelt or membrance surface of roof tiles/concrete padding etc including grubbing up of tree roots, removing all the debris to a distance n exc 100m for roof treatment work, preparation of the concrete roof surfaces by scrubbing down with steel brushes and cleaning with water all loose dirt/dust and applying the following Roof Treatment complete all as specified & directed :- (a) Applying 1st course of 15mm thick screed bed in cement mortar 1:4 over concrete surfaces. (b)Applying 2nd course of bitumenous primer conforming to IS-3384 @ 0.4 Kg/Sqm over the screed bed. (c) Applying 3rd coarse of a coat of blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm. (d) Applying 4th course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat. (e) Applying 5th course of a coat of bonding materialwithblown type bitumen of grade 85/25 heating to aworking temperature of 180° C and applied @ 1.2 Kg/Sqm. (f) Apllying two coat of aluminium paint on top of the APP surface all as specified |
| 150 | Supply only water proofing compound (Liquid) complete all as specified. |
| 151 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed. |
| 152 | Taking down carefully existing sub main wiring complete of any size and capacity complete all as specified and directed. |
| 153 | Taking down carefully existingunserviceableUG cable of any size and capacity complete all as specified and directed. |
| 154 | Taking down carefully unserviceable main switches, DBs including MCBs etc. complete of any size and capacity complete all as specified and directed. |
| 155 | M&L for point wiring one light / fan/Exhaust fan point controlled by one way switch(concealed type) complete with multistranded copper conductor flame retardant low smoke (FRLS)1.5 Sqmm size PVC insulated unsheathed cable 1100 volts grade drawn through with and incl medium grade duty concealed PVC conduit ISI marked not less than 20mm dia including conduit fittings and accessories such as socket,elbow,junction box, bell mouth,bend, reducer etc complete incl cutting chases inexisting walls of any description built in cement mortar and making good the disturbed surfaces in cement mortar (1:4)and finishing the surfaces to match with existing surfaces and finish with using sunken type pressed steel terminal boxes of required sizes of not less than 1.6 mm thick factory made and factory painted with top cover of 3 mm thick plastic laminated sheet fixed with brass screws washers with all accessories including single core multi stranded copper conductor1.5 Sqmm size PVC insulated unsheathed cablegreen in colouras earth wire to common earth andconnected to earth dolly drawn in same conduit complete all as specified .NOTE :-Wire/Cablecolour coding Shall be maintained properly as per IE rule. |
| 156 | All as per item No 155 but for one 3/5 pin socketoutlet 5 Amps on the same board with other switches. |
| 157 | All as per item No 155 but for one 3/5 pin 5 Amp socket outleton independent board. |
| 158 | All as per item No 135 above here in before but with 4.0 Sqmm (nominal area) cable PVC insulated but unsheathed for the 15 Amp 3/5 pin socket power point including 2.5 Sqmm copper conductor green in colour for earth continuity on independent boardcomplete all as specified and directed. |
| 159 | S&F switch piano flush type polycarbonate single pole one way 5 Amps complete all as specified and directed. |
| 160 | S&F socket outlet polycarbonate 2 in 1, 3 pin 5 Amps flush type complete all as specified and directed. |
| 161 | S&F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal complete all as specified and directed. |
| 162 | S&F bell push flush type 5 Amps complete all as specified and directed. |
| 163 | S&F Ding Dong musical AC. 230 volts,single polecomplete all as specified and directed. |
| 164 | S&F Ceiling rose three teminal /PVC/ polycarbonate,insulated body complete all as specified and directed. |
| 165 | S&F electronic fan regulator, 2 module, 100 watt, (5 stepped type), 240 Volt for 1200/1400 sweep AC ceiling fan complete all as specified and directed. |
| 166 | S&F energy efficientLED bulk head luminaire, 1x15 watt,wall mounted made of die cast aluminium with opal diffuser IP-65,LED lamp, lamp holders, etc. complete with all accessories including connecting up with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting 230V, 50 HZ, complete all as specified and directed. |
| 167 | S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including one LED retrofit Lamp of B-22 holders base warm white Code No LHLDRUEML8X005 of make Havells or equivalent make of Phillips/Crompton etccomplete all as specified and directed. |
| 168 | S&F of LED tubelight fitting 1 x 20W inverter batten type fitting, 4 feet long, aluminium extruded housing, IP-20 rated, voltage 230 volts (operating range 140 volts to 270 volts), 50 Hz, system wattage 20 watt ±10%, system current not less than 102mA, power factor more than 0.95, system lumen efficacy 100 lm/wattCCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% with all accessories pre-wired and making connection with three core PVC insulated overall sheathed flexiable copper cable of size 0.75sqmm from ceiling rose to light fitting, complete all as specified & directed. |
| 169 | Supply and fixing factory made epoxy powder coated distribution board, SPN, 12 ways with metal door (IP-43 protection), confirming to IS : 8623 fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall, suitable for universal mounting including 200 Amp copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts, suitable for one SPN/DP MCB as incomer and SP MCB outgoing, complete all as specified & directed . |
| 170 | Supply and fixing factory made epoxy powder coated distribution board, SPN, 8 ways with metal door (IP-43 protection), confirming to IS : 8623 fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall, suitable for universal mounting including 200 Amp copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts, suitable for one SPN/DP MCB as incomer and SP MCB outgoing, complete all as specified & directed . |
| 171 | Supply and fixing in replacement of factory made flush shutter type sheet metal enclosures, double door ,for MCCB DB load link, vertical, triple pole and neutral, 4 Way IP-43, suitable for MCCB up to 160 A as incomer ,complete all as specified and directed . |
| 172 | Supply and fixing 240V, 10 KA "B" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing andcommissioning complete all as specified & directed. |
| 173 | Supply and fixing 240V, 10 KA "B" curve miniature circuit breaker (MCB) of SPNand current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing andcommissioning complete all as specified & directed. |
| 174 | Supply and fixing 240V, 10 KA "B" curve miniature circuit breaker (MCB) of SPNand current carrying capacity 40 to 63 AMP, in the MCB DB Complete with connection testing andcommissioning complete all as specified & directed. |
| 175 | S&F in replacement of MCCB 160 Amps four pole 415 volts thermal magnetic release ICU=100% ICS having breaking capacity 16 KA including connection terminal strip complete all as specified & directed. |
| 176 | M&L forsub main wiring with 2 Single core PVC insulated unsheathed FRLScable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sqmm (nominal area) drawing in and including 25 mm dia or higher medium dutyPVC concealed conduit and conduit accessories and fittings. including one single core green colour PVC Insulated unsheathed FRLS cable copper conductor multistranded of size 4.0 Sq mm as earth wire upto common earth and connected to earth dolly complete all as specified & directed. |
| 177 | Supply, hanging and testing of BEE 5 Star rated energy efficient brushless direct current motor (BLDC) ceiling fan, 1200mm (48 inch) sweep, having 3 blades made of aluminium alloy, down rod, canopies, shackles, 240 volt, single phase suitable for input voltage range 140-285 volts, AC, 50Hz, power factor not less than 0.99, service value minimum 8 cubic metre / min/ watt or higher, air delivery minimum 230 cu metre/ min or more, power consumption maximum 28 watt or lower, top speed minimum 340 RPM or higher, THD not more than 10% including5 step electronic regulator marked on rotating knob, two module, 100W, 240 volts with 3 years on site warranty for speed control, copper winding, complete as per IS:374-1979 or latest IE rule & site requirement, colour white complete and taking down old unserviceable fan of any type/ size from existing location and depositing in MES storeyard, complete all as specified & directed. |
| 178 | Supply & fixing metallic exhaust fan, 300mm (12") sweep, single phase, 230 volts, 50 Hz AC, 1400 RPM, energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminiun rotor mounted on two ball bearings, complete with louvers and shutters,connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cableincluding cutting holes in existing brick walls for making opening for fixing of exhaust fan of 300mm sweep including grounting bolts/nuts and making good disturbed surface of walls using cement sand mortar 1:4, complete all as specified & directed. |
| 179 | Supply, installationand testing of water heater storage type (Geyser) single phase, 230V, 50Hz, 5 star energy saving, high density PUF insulation tank made of heavy duty magnesium anode rod with steel core to protect enamelled tank from rust & corrosion, vertical installation type, 25 Litre capacity, 2000 Watt rated power, incoloy 800 glass coated heating element, tank coating of ferro glass dry powder tank made of ultra thick super cold rolled steel plates, rated pressure 0.8MPa, IPX4 protectionconsist of safety valves, thermal cut off, thermostat including connecting up fixed to walls by drilling of holes, grouting of bolts of suitable size with nuts etc and makinggood disturbed surface,complete all as specified & directed. |
| 180 | Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 25 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed. |
| 181 | Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 35 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed. |
| 182 | Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 70 Sqmm 3.5 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed. |
| 183 | Intergral LED security light luminaire 60W LED, 230 volts made up of pressure die cast aluminium housing powder coated with high power SMD LED’s lens & toughned glass IP-66, luminaire efficacy >110 Lumens per Watt, Secondary optics for better light distribution, having two nos Potted driver (OEM) (one inbult and one spare potted driver) 4KV internal +10KVSPD, THD<10%, pf>0.95,mounted on & includingGI bracket made out of 40mm bore medium grade pipe of 1.70m length, bent to required shape,fixed on PCC/Steel pole with 02 Nos. clamps of flat iron (40 x 6mm), nuts, bolts and washers including painting with two coats of aluminium paint over a coat of red oxide zinc chrome primer, making connection with PVC copper conductor cable of 1.5 sqmm and taking down old unserviceable light fitting, complete all as specified & directed. |
| 184 | M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and connecting to main switch or switch board complete and incl PCC masonry pit of 300x300x300mm interior dimensions in PCC 1:2:4 type B-1 RCCcover with GI frame, charcoal and common salt 15cm in layers all round the earth plate, 15mm dia GI watering pipe, a funnel with wire mesh should be provided on top of watering pipe complete all as specified as per electric plate No 3 of SSR 2009 including testing after completion complete all as specified and directed. |
| 185 | M&L for laying GI tubing light grade 50mm dia with all fittings & GI MS clamps of 50 x 6 mm incl nuts and washers for fixing of GI pipe complete all as specified and directed. |
| 186 | M&L for well burnt brickwith sub class ‘B’ old size bricks for protection of cablecomplete all as specified and directed. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
