|
| 1 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.All kinds of soil : |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 3 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 4 | Neat cement punning |
| 5 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 6 | Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and curing complete |
| 7 | Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with:Cement mortar 1:6 (1 Cement : 6 coarse sand)Nallah |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns etc. for mass concrete. |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts. |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for: Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms. |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide |
| 13 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 14 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 15 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 16 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level andabove plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 17 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6( 1 cement : 6 coarse sand) |
| 18 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 19 | Half brick masonry with non modular fly ash bricks of class designation 10, conforming to IS: 12894, in superstructure above plinth level and upto floor V level and curing complete in: Cement mortar 1:4 ( 1 cement : 4 coarse sand ) |
| 20 | 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
| 21 | 12mm Cement plaster of mix:1 : 6 ( 1 cement : 6 coarse sand) |
| 22 | 15mm Cement plaster on the rough side of single or half brick wall of mix:1 : 6 ( 1 cement : 6 coarse sand) |
| 23 | VITRIFIED FLOOR TILESProviding and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size of tile 600x600 mm |
| 24 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60mm thickness, including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.60mm pressed, mild steel welded or rigidly fixed together by mechanical means, including M.S pressed butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre- reatment of the surface as directed by Engineer-in-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb |
| 25 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.35 mm |
| 26 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge Second class Kail wood 30 mm |
| 27 | Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.0mm thick glass panes |
| 28 | Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S Flat 15x3 mm and nuts and bolts complete.Galvanized M.S wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 29 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to steel windows by welding |
| 30 | Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete :75x47x1.70 mm |
| 31 | Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete : 125 mm |
| 32 | Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete250x10 mm |
| 33 | Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete100x10 mm |
| 34 | Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm |
| 35 | Providing and fixing bright finished brass hard drawn hooks and eyes150 mm |
| 36 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete |
| 37 | Supplying, filling, spreading and leveling stone boulders of size range 5 cm to 20 cm, in recharge pit in the required thickness for all leads and lifts all complete as per direction of Engineer-in-charge. |
| 38 | Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete. |
| 39 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 40 | Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) |
| 41 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 42 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. The sections shall be welded. |
| 43 | C.G.I. SHEETS ROOFINGProviding corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. with 0.63 mm thick with zinc coating not less than 275 gram/m2 |
| 44 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.Single socketed pipes 110mm diameter |
| 45 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. |
| 46 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with White P.V.C automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS:2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required:Single half stall urinal with 5 liter P.V.C automatic flushing cistern. |
| 47 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40mm C.P. brass waste and 40 mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the walls wherever required : Size 600x450x200 mm |
| 48 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 49 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 50 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: Semi rigid pipe, 32 mm dia |
| 51 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 52 | Providing and fixing UPVC pipes 6kg pressure for soil and waste water pipes with required specials like bends/tees/union etc. Including making the base and covering the same with cement concrete 1:3:6 as per the direction of the engineer-in-charge. The work shall include any kind of chasing and supports as per the manufacturer\"s spedcification including the repair of the chases with required cement mortar 1:6 of concrete of mix 1:2:4.:- 75mm dia pipes |
| 53 | Providing and fixing UPVC pipes 6kg pressure for soil and waste water pipes with required specials like bends/tees/union etc. Including making the base and covering the same with cement concrete 1:3:6 as per the direction of the engineer-in-charge. The work shall include any kind of chasing and supports as per the manufacturer\"s spedcification including the repair of the chases with required cement mortar 1:6 of concrete of mix 1:2:4.:- 100mm dia pipes |
| 54 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.:-20mm nominal outer dia pipes. |
| 55 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.:- 25mm nominal outer dia pipes |
| 56 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 57 | Providing and fixing 15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 |
| 58 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 |
| 59 | Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg. |
| 60 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. Of quality and make as approved by Engineer - in - charge. |
| 61 | Providing and fixing uplasticized PVC connection pipe with brass unions, 45 cm length, 15 mm nominal bore. |
| 62 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S and S as per IS:1729 |
| 63 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 64 | Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar. |
| 65 | Wiring for light point/ fan point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch,phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. Make-Havells/Anchor/Finolex/Plaza:- Group A |
| 66 | Wiring for light point/ fan point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch,phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. Make-Havells/Anchor/Finolex/Plaza:- Group B |
| 67 | Wiring for light point/ fan point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch,phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. Make-Havells/Anchor/Finolex/Plaza:- Group C |
| 68 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire Make -Havells/Anchor/Finolex/Plaza |
| 69 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 4.0 sq. mm + 1 x 4.0 sq. mm earth wire Make -Havells/Anchor/Finolex/Plaza |
| 70 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (Double door-12 Way) |
| 71 | Supplying and fixing of 5 amp to 32 amp rating 10KA breaking capacity 240V C curves miniature circuit breaker of single poles in the existing MCB,DB complete with connections testing and commissioning etc. as required.(Make- Havells/L&T/Siemens/ABB):- 10 Amp, Single Pole |
| 72 | Supplying and fixing of 5 amp to 32 amp rating 10KA breaking capacity 240V C curves miniature circuit breaker of single poles in the existing MCB,DB complete with connections testing and commissioning etc. as required.(Make- Havells/L&T/Siemens/ABB):- 20 Amp, Single Pole |
| 73 | Supplying and fixingfollowing double pole 240V isolatorin the existing MCB,DB complete with connections testing and commissioning etc. as required (Make-Havells/L&T/Siemens/ABB):- 40 Amp, Double Pole |
| 74 | Supplying and fixingfollowing double pole 240V isolatorin the existing MCB,DB complete with connections testing and commissioning etc. as required (Make-Havells/L&T/Siemens/ABB):- 63 Amp Double Pole |
| 75 | Supplying and fixing metal box of following size (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including paintint etc. As required.:- 200mmx150mmx60mm deep |
| 76 | Supplying and fixing metal box of following size (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including paintint etc. As required.:- 200mmx250mmx75mm deep |
| 77 | Supplying and fixing following piano type switch/ socket on the existing switch box/cover including connections etc. as required.(Make-Anchor/Havells/Philips):- 5/6 Amp. Switch |
| 78 | Supplying and fixing following piano type switch/ socket on the existing switch box/cover including connections etc. as required.(Make-Anchor/Havells/Philips):-3 pin 5/6 amp socket outlet |
| 79 | Supplying and fixing following piano type switch/ socket on the existing switch box/cover including connections etc. as required.(Make-Anchor/Havells/Philips):15/16 amp switch |
| 80 | Supplying and fixing following piano type switch/ socket on the existing switch box/cover including connections etc. as required.(Make-Anchor/Havells/Philips):-6 pin 15/16 amp socket outlet |
| 81 | Supplying and fixing brass batten/angle holder including connection etc. As required |
| 82 | Supplying and fixing 3 pin 5A Ceiling rose on the existing junction box including connection etc. As required |
| 83 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc, as required |
| 84 | Providing,and fixing ofprewired LED tube light fitting (36W,1150mm)with integrated batten complete with all accessories and tube/lamp directly on ceiling/wall including connections with 1.5sqmm FRLS PVC insulated copper conductor, singe core cable and earthing etc. As required |
| 85 | Supply, Installation testing and commissioning of ceiling fan including wiring thedown rod of standard length (upto 30cm)with 1.5sqmm FRLS PVC insulated copper conductor, singe core cable, including phenolic laminated sheat cover on the fan box etc. As required, Celling fan 1200mm sweep (Make-Orient/Havells/CG/Bajaj) |
| 86 | Supply, Installation testing and commissioning of Wall mounting fan including wiring with 1.5sqmm FRLS PVC insulated copper conductor, singe core cable, including making the hole to suit the size of the above fan, making good the damages. As required, Wall fan 400mm sweep(Make-Orient/Havells/Bajaj/CG) |
| 87 | Supply, Installation testing and commissioning of Split type Air Conditioner 1.5 Ton, hot and cold,of minimum 3 star rating . As required, (Make-Voltas/Lloyd/Blu star/Hitachi |
| 88 | Supply, Installation testing and commissioning of Split type Air Conditioner 2.0 Ton, hot and cold of minimum 3 star rating . As required, (Make-Voltas/Lloyd/Blu star/Hitachi |
| 89 | Supply of LED lamp 9 watt (Make Baja, wipro, surya etc) |
| 90 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 91 | Supplying and laying 6SWG GI Wire at 0.5 mtr below ground level for conductor earth electrode, including connection/termination with GI thimble etc as required |
