Bharat Sanchar Nigam Limited-BSNL has published Tender For Construction Of Metropolitan Court Complex Building At Jodhpur. Submission Date for this Tender is 02-10-2023. CCTV System Tenders in jodhpur Rajasthan. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | SITC of IP Based 5MP Dome camerawith Software License : 1/2.8" Progressive CMOS, ICR, Olux with IR, 2560(H)x1920(V):25fps(P) , 2.8/3.6 mm lens (As persite requirement) H 264,H265/MJPEG, dual-stream, 120dB WDR or better, 3D DNR, BLC, IR: minimum 30 mtr, Provision for Support on-board storage up to 256 GB (SD card not included),intrusion detection, Line crossing detection, Motion detection, Dynamic analysis, Alarm should be trigger on (Tampering alarm, Network disconnect, IP address conflict, Storage exception), security feature such as (password protection, privacy mask, watermark, IP address filtering, anonymous access), Open standard to support ONVIF (PROFILE S, PROFILE G),Metal Housing, Vandal-proof housing IP 67, DC 12V & PoE, Complete with Junction box for cable management Oerating Conditions : 20 °C - 50 °C or better. Certificate of Complianced: UL, CE and FCC. compliance. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure "A" attached with PWD Electric BSR |
| 2 | SITC of Bullet- Fix Camera5 MP withSoftware License , Video Resolution: 5MP, 2592(H)x1944(V) Pixels , 1 to @25 fps; Image Sensor: 1/2.8-inch CMOS; Built in Infra-Red: 40 to 50 mtr; High Dynamic Range- 120 dB WDR; Lense- 2.8/3.6 mm, ;H264,H265/MJPEG , provision for Support on-board storage up to 256 GB (SD card not included) , intrusion detection, Line crossing detection, Motion detection, Dynamic analysis, Alarm should be trigger on (Tampering alarm, Network disconnect, IP address conflict, Storage exception), security feature such as (password protection, privacy mask, watermark, IP address filtering, anonymous access), Open standard to support ONVIF (PROFILE S, PROFILE G),Metal Housing, Vandal-proof housing IP 67, DC 12V & PoE, Complete with Junction box for cable management Oerating Conditions : -30°C to + 70 °C or better.Onvif Profile S,G,Confirmant; UL Certified compliance All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure "A" attached with PWD Electric BSR |
| 3 | SITC of Video Management and Storage Server appliance, withSoftware Base pre-configured and pre-installed. with a capacity of connecting upto 256 concurrent recordable cameras with pre installed storage capacity of 64TB and extended up to 64TB &Hot Swappable SATA-III hard drives in a fault tolerant full featured RAID-5 configuration; video compression withH264;H265 encoding system, Gold Level; UL Certified, Number of USB port 6the Cameras, VMS Software and the video management andstorage server should be from the sameOEM All as per pre approved by Engineer in charge complianceFor additional technical parameters of products/ work refer Annexure "A" attached with PWD Electric BSR |
| 4 | SITC of Client Workstation License, Intel® i7processor, 8GB RAM, 256GB SSD ,NVIDIA graphic Card, 4 port,one RJ 45 connector ,one serial port Display port /HDMI /VGA/USBType C , Dram bus with 64 bit, Temperature range-Operating (0 °C to 35 °C) Storage - - 40 °C to 65 °C Quardo P4000 or equivalent,Keyboard optical Mouse with all respect etc.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure "A" attached with PWD Electric BSR |
| 5 | SITC of BIS Certified Company55" LED Monitor, Professional series,Resolution 3840x2160, 60Hz LFD Display, 2 x HDMI Port 1 x USB Port,Inbuilt media player-should be as per OEM for web browser & file sharing compatibility through IP, RJ45, Wi-Fi 5, Bluetooth, Contrast Ratio - 4000:1, Response time- 8 ms or better , Brightness 300 nits or higher, Built in speaker,Viewing angle 178° x 178°,Wall mount for Display:,Fix Wall mount with ,External media player compatible for above if required Safety & EMC Certifications- CE,FCC,UL,, with required HDMI cableAll as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure "A" attached with PWD Electric BSR |
| 6 | Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (UnshieldedTwistedPair), Category 6, ClassE, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568, The copper conductors should be balanced twisted in pairs, seperated by across-member fluted pair divider & protected by PVC Jacket. Certified er for mance in a 4-connector configuration up to 100 Mtrs channel requirements & transmission frequencies upto 250Mhz. in existing MS/PVC Conduits /casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per preapproved by Engineer incharge. For additional technical parameters of products /work, refer Annexure "A" attached with this BSR . |
| 7 | Supply and Installation of unsheilded Information outlets made of high impact plastic body with ABS, FRGrade with provision for protection against dust in jack/FP, suitable for Cat6/6A application complying to latest ammendments, According to Cat.6/6A channel, It should support channel as well as components requirements of Cat.6/6A standard sat frequencies of upto 250 to 500Mhz. Cat6/6A unshielded/ shielded Jack should be suitable to terminate 4pair, 23/24 AWG solid/ stranded wire diameters, using 100 Ohm unshielded/ shielded balance twisted pair cable, the jack should have too less/impact punch termination on reliable copper tin plated Insulation displacement contact, It complied with ANSI/ TIA/ EIA568 standard.In existing modular/ MS Boxes along with necessory connections as required complete in all respect. All as per preapproved by Engineer incharge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR. |
| 8 | Cat 6, Un-sheilded Information Outlet |
| 9 | Supply & fixing of square Face plate for Flush/ Surface Mount Information Outlets Single/ Dual or Quad Aperture, material should be PC+ ABS body, Suitable for RJ45 unshielded/ shielded connection modules. Should match with I.O. OEM. Dimensions should be 86mmX86mm as required complete in all respect. All as per preapproved by Engineer incharge. For additional technical parameters of products/work , refer Annexure "A" attached with this BSR . |
| 10 | Single Aperture |
| 11 | Supply, Installation, Testing and Comissioning of Rackmounted 19" 1U, 24 Port Unloaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic(ABS), Modular Patch Panels (withoutI.O.)with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel,. There should be a provision for each port/jack on the panel and reusable removable onfield from the panel complete in all respect. All as per preapproved by Engineer incharge.For additional technical parameters of products/work, refer Annexure"A"attached with this BSR . |
| 12 | Supply, Installation and Testing of 4pair, 100 Ohm impedance, Cat6/6A patchcords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors as per ANSI/TIA/EIA568 suitable for Cat6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA 568, minimum requirement for 1G BASE-T/10G BASE-T performance. Patchcords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, Minimum 750 to 1000 mating cycles in plug contacts for long durability complete in all respect. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR. |
| 13 | Cat 6, UTP (Un-sheilded Twisted Pair) Patch Cord |
| 14 | 1 Mtr/3 ft |
| 15 | 3 Mtr / 10 ft. |
| 16 | Supply, Installation, Testing and Commissioning of Wall mounted ISO9001:2015&14001 or higher level certified company made Communication enclosure(Rack)of Minimum 500MM Depth with made from CRCA & hot dip powder coated, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door,Vertical Mounting Rail 1.6MM with"U" Marking, with All round protective channel on the door aperture, lock integrated on front door,top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19"angles with wall mounting provision on wall. Accessories like:1Noof19" 1 U Horizontal Cable manager, 2No of 90cfm 230VAC Fan with 1mts long cable, mounting hardware, 1No of 19" 1U, mountable socket strips with 6 nos of 5A universal sockets with 2mts long power chord for supplying power to switches,fans etc alongwith earth continuity kit, indicator, moulded power supply cable. fixing on wall with fastner of suitable capcity etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . |
| 17 | 42 U Rack for Server |
| 18 | 12 U wall mounted Enclosure |
| 19 | Supply , Installation, Testing and Commissioning of Managed Layer-2 Intelligent Giga Ethernet Switch providing 24 x 10/100/1000 MBPS Giga Ethernet ports and with min 4 SFP Giga Ports (provision for Fiber Giga connectivity) with provision of minimum Stacking of 06 Switches with related LAN Base Software including making connections etc as required complete in all respect complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . |
| 20 | S&F following sizes (dia.)of ISI marked MMS(IS:9537P-III)vergin material PVC conduit as per PWD specification for electrical Works along with its accessories(IS:3419)as required in recess including cutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per preapproved by Engineer incharge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR . |
| 21 | 25 mm |
| 22 | Supply, Drawing and Testing, of stranded Single mode (9/125 µm) glass optic fiber cable, as per latest ammendments of TIA/EIA 568/ISO/IEC 11801:2011/ IEC 60794-1-2, construction of LSZH outer sheath cable, cable should be used for LAN and WAN back bones, . With its LSZH sheathing these cables should be ideal for indoor/outdoor installations in existing MS/PVC /HDPE Conduits/ slotted channels with ferruling at both ends for identification complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR . |
| 23 | 6 Fiber |
| 24 | Supply, Installation, & Testing of 19" 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated, Singlemode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable duplex adapters for ST/E-2000/SC/LC/MT-RJ/PC type, It should have easy removable Top plate with push buttons, there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores, splice tray should be PC+ABS material, it should include accessories like mounting hardware, gormetts, heat shrink tubes/sleevs, screws, nuts to install the panel for rack/wallmount applications as per requirment complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. |
| 25 | 12 Port |
| 26 | Supply, Installation, & Testing of Indoor duplex Singlemode patch cord (9/125 µm made of glass fiber optic with LSZH jacket, Multimode G652.D Mounted on both sides with ST/E-2000/SC/LC/MT-RJ/PC type Duplex connectors in acc. with IEC 61754-20 as per latest ammendments of TIA/EIA 569B.3, as per requirements complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . |
| 27 | Single Mode Patch Cord 2 Mtr. |
| 28 | Supply , Installation, Testing and Comissioning of Hot pluggable Small Form Factor Pluggable (SFP Module), 1000BASE-LX, 1G Fiber Channel, LC Type Duplex Connector, 1310 nm laser transmitter, Should support distance upto 10 km on 9/125 um of data rate upto 1.25 Gb/s on bi-directional data links. Should also support industrial temperature, should have metal enclosure for lower EMI. The transceiver should be ROHS Compliant. (For Each SM Fiber) complete in all respect. Switch & SFP module should be of the same make. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR. |
| 29 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, , in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . |
| 30 | 2 x 1.5 sq.mm |
| 31 | Supply , Installation, Testing and Comissioning of Floor standing ISO 9001:2015 & 14001 or higher level certified company made Communication enclosure (Rack) of 600 MM Depth with made from CRCA & hot dip powder coated,Vertical Mounting Rail 1.6 MM with "U"Marking, front sturdy sheet steel frame folded from one piece and welded with 5mm toughened glass door, with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, Accessories like: 5 Nos of 19" 1U Horizontal Cable manager, 2 Nos of vertical cable managers, 2 Nos of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of 19" 1U, mountable socket strips with 6 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR. |
| 32 | 18U Floor Standing Enclosure |
| 33 | Supply. Installation, Testing and Commissioning of L2 managed Switch; 24XI0/I00/1000 BASE-T port and with min 4x 1000/1 0000 BASE-X SFP (With 2 SFP module for fiber Giga Connecti vity); Total power budget: minimum 350W. Switching Capacity 56 GBPS or better; MAC Table SK or better: Rack mounting; Flow Control; QoS; 802. l Q Standard VLAN, Network Management; Wide working temperature: -05~55°C; Lightning Protection Common mode 4KV; Certificate of compliance: CE/FCC, including making connections etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work . refer Annexure "A" attached with P.W.D. Electrical B.S.R. |
| 34 | SITC of of Conference Room Solution Central Control Unit for control of all microphones:Supply voltage Adaptor 100 to 240 VAC, 50/60 Hz Current Consumption voltage Adaptor 1.9 A (100 VAC) to 1 A 240 (VAC) DC voltage Control Unit 24 V, 6.0 A Maximum number of Discussion Devices for Control Unit (without Extension Unit)40 Discussion Devices per trunk 80 Discussion Device in total 24 V, Max 5.2 A (short-circuited protected) Discussion Device loudspeakers volume control 15 steps of 1.5 dB (starting from -10.5 dB) Limit threshold level to unit 12 dB above nominal level Gain reduction due to number of open microphones (NOM) 1/SQRT (NOM) Sample rate 44.1 kHz Frequency response 30 Hz to 20 kHz Ethernet speed 1 Gb/s Nominal input (85 dB SPL) < 0.5% Max. input (110 dB SPL) < 0.5% XLR nominal microphone input -56 dBV XLR maximum microphone input -26 dBV RCA nominal input -24 dBV (+/- 6 dB) RCA maximum input +6 dBV S/N > 93 dBA Frequency response 30 Hz to 20 kHz THD <0.1% RCA nominal output -24 dBV (+6/- 24 d.etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. |
| 35 | SITC of Discussion Unit: Power consumption 1.3 W Frequency response 30 Hz to 20 kHz (System electrical) THD <0.5 % S/N >93 dBA Sampling rate 44.1 kH Headphones load impedance > 32 ohms < 1k ohm Loudspeaker max. peak output power 4 W Loudspeaker nominal output 72 dB SPL Participants loudspeaker frequency response 200 Hz to 16 kHz (acoustical) Microphone polar pattern CardioParticipants microphone frequency response 125 Hz to 15 kHz Microphone nominal input 85 dB SPL Dimensions device without microphone(H x W x D) 64 x 203 x 146 mm(2.5 x 8.0 x 5.7 in) Height with microphone in horizontal position 130 mm (5.1 i ) Length of microphone from mounting surface lenth480 mm (18.9 in)etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. |
| 36 | SITC of Mixer cum Aplifier having Channels (Mono + stereo): 5 + 3; Microphone inputs (XLR): 5; Auxiliarys (FX, AUX): 1 Post, 1 Pre; Max. single channel output power, dynamic-headroom, IHF-A- into 4 ?,into 8 ?:640 W, 350 W; Max. dual channel output power, dynamic-headroom, IHF-A-into 4 ?,into 8 ?:2 x 600 W,2 x 340 W; Max. single channel output power, continuous, 1 kHz, THD = 1%- into 4 ?,into 8 ?: 500 W,280 W; Maximum midband output power, 1 kHz, THD = 1%, dual channel- into 4 ?, into 8 ?: 2 x 450 W,2 x 270 W; Rated output power, 20–20000 Hz, THD < 0.5%, one channel loaded- into 4 ?, into 8 ?: 2 x 400 W,2 x 240 W; Max. output power, Direct Drive mode (bridge confi guration), continuous, 1 kHz, THD =1% : into 12 ? 680 W; Maximum output voltage, power amplifi er, 1 kHz, no load- Dual channel mode, Direct Drive mode: 52 Vrms,100 Vrms; THD, at 1 kHz, MBW = 22 kHz - MIC input to master A L/R outputs, +10 dBu, typical, MIC input to speaker output: < 0.015%,< 0.15%; DIM 30, MIC input to speaker output, 3.15 kHz, 15 kHz: < 0.05%; IMD-SMPTE, MIC input to speaker outputs, 60 Hz, 7 kHz: < 0.15%; Frequency response, -3 dB, ref. 1 kHz-Any input to any Mixer output, Any input to Speaker output :15–22000 Hz,20–22000 Hz; Crosstalk, 1 kHz -Amplifi er Ch1/Ch2, Channel to channel: < -85 dB,< -78 dB; Microphone mute switch attenuation: > 100 dB; Channel VOL and FX/AUX-send attenuation: > 85 dB;CMRR, MIC input, 1 kHz: > 80 dB; Input Sensitivity, all level controls in max. position- MIC, LINE (mono), LINE (stereo), CD (stereo) :-65 dBu (435 µV), -45 dBu (4.35 mV), -27 dBu (34.6 mV); -27 dBu (34.6 mV); Maximum level, mixing desk, input VOL down, output VOL up - MIC inputs, GAIN at min. position, Mono line inputs, GAIN at min. position, Stereo line inputs, PHONES outputs, MASTER A, B, AUX outputs: +11 dBu, +30 dBu, +26 dBu, +21 dBu,+11 dBu; Input Impedances- MIC,CD, All other inputs: 2 k?,10 k?,> 15 k?; Output Impedances- Phones, All other outputs (impedance balanced), 47 ?,150 ?; Equivalent input noise, MIC preamp, A-weighted, max. gain, 150 ? : -129 dBu; Noise, Channel inputs to master A L/R outputs, MBW = 22 kHz, A-weighted -Master volume down, Master volume center, all channel volume down, Master volume center, all channel volume center : -99 dBu, -90 dBu, -85 dBu; Signal/noise-ratio, power amplifi er, A-weighted, 450 W, 4 ?: 104 dB; Output stage topology, amplifier: Class D; Equalization- LO shelving,MID peaking, HI shelving : ±15 dB / 60 Hz, ±12 dB / 2.4 kHz, ±15 dB / 12 kHz; Master EQ 7-band (63, 160, 400, 1k, 2.5k, 6k, 12k Hz):±10 dB / Q = 1.5; Filter-Low cut, microphone processing (switchable), Low cut, amplifi er (engaged in 100 V Direct Drive mode), Speaker processing: 80 Hz, 18 dB/oct. or 150 Hz, 12 dB/oct., 50 Hz or 70 Hz, 18 dB/oct., LPN, switchable; Delay master B, selectable:0–145 ms (0–50 m); Effects- Type, Effects presets, Remote control: Stereo 24/48-bit multi effects, processor, 32 factory presets, user editable Footswitch; Display:128 x 64 pixels, LCD; Audio player (USB at front panel),USB mass storage class, supported fi le systems, Supported audio file formats, Interface, USB power supply, max. rated current (short circuit proof) : FAT 32,MP3, WAV, USB2.0, female type A, 5 V, 500 mA; Digital Audio Interface (USB at rear panel)- Channels, AD/DA conversion, A18 Sampling rate, PC interface : 2 in, 2 out,16-bit, delta-sigma, 32/44.1/48 kHz, USB2.0, female type B; Protection- MASTER A, B, AUX outputs, Amplifier, Switching mode power supply (µC controlled) : Adjustable peak limiters, -10 – +11 dBu, Audio limiters, high temperature, DC, HF, short circuit, peak, current limiters, turn-on delay, back EMF,Inrush current limiters, mains over / undervoltage, mains over current, high temperature; Cooling : Continuous speed controlled fan; Phantom power, switchable: 48 V DC; Power requirements (SMPS with auto range mains input): 100–240 V AC, 50–60 Hz; Power consumption, at 1/8 maximum output power, 4 ?:180 W; Safety Class:I; Operating temperature 5° to 40° C (40° to 105° F); etc ae Req. The OME should have EN/CE/UL compliedcertification .All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. |
| 37 | SITC of Handheld Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiverhaving 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz; with required 2 core shielded microphone cable with XLR Socket /Phone Socket /Other Conncetoretc ae Req. The OME should have EN/CE/UL compliedcertification .All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. . |
| 38 | SITC of Freestanding Gooseneck Mic with base Connector Voltage range 12 to 48 V Current consumption <8 mA Sensitivity 0.7 mV @ 85 dB SPL (2 mV/Pa) Maximum input sound level 110 dB SPL Distortion <0.6% (maximum input) Equivalent input noise level 28 dBA SPL (S/N 66 dBA ref. 1 Pa) Frequency response 100 Hz to 16 kHz Output Impedance < 200 ohm Cable length 2 m (78 in) Connector 5-pin DIN 180° (lockable)etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. . |
| 39 | SITC of 4" 2-Way Full Range Coaxial Ceiling Main Loudspeaker, Professional Series; having Frequency response (-10 dB): 65 Hz - 20 KHz; Coverage (conical): 130°; Power handling: 50 W cont. / 200 W peak; Sensitivity (SPL 1W/1m): 86 dB; Max calculated SPL: 103 dB cont. / 109 dB peak; Impedance: 8 Ohms nominal (transformer bypass); Network & Transducers Protected: 12 dB/oct 3.3kHz ; LF transducer: 4 in (100 mm) Polypropylene cone; HF Transducer: 75in. (19mm) Ti Mylar Laminate;Transformer Taps: 70V: 1.88, 3.75,7.5,15 or 30W, 100V: 3.75,7.5,15, or 30W; Bypass :8O; Connectors: C4.2:Phoenix type removable, with screw terminals and "loop -thru", accepts 12 ga wire; C4.2D: Fire-safety rated input block, 3 terminal barrier strip accepts 12 ga wire; Enclosure Material: Baffl e - UL 94V-O rated ABS Backcan - Zinc plated steel; Safety agency ratings: UL-1480;IP rating: 54 or better; Preferredetc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. . |
| 40 | SITC of 10" Ceiling Mount Sub-Woofer, Professional Series with same footprints as Main Speaker having Frequency response (-10 dB): 45 Hz - 150 Hz; Coverage (conical): 180°; Power handling: 100 W cont. / 400 W peak; Sensitivity (SPL 1W/1m): 94 dB; Max calculated SPL: 114 dB cont. / 120 dB peak; Impedance: 8 Ohms nominal (transformer bypass); Network: 12 dB/oct; LF transducer: 10 in (260 mm) high-compliance; driver (weatherized cone) Input configuration: 8O; 70V/100V power taps: 7.5 (70V only)/15/30/60 W; Connectors: Phoenix type removable, with screw terminals and "loop -thru", accepts 12 ga wire Enclosure: Steel enclosure and UL94V-0 rated baffle and bezel; Acoustic design: Ported cabinet, internally damped w/passive crossover; Safety agency ratings: UL-1480A ; etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. |
| 41 | SITC of Conference Cable XLR Wire -Copper, stranded 1 mm2 .<0.018 ohm/m Fiber -PMMA, 1 mm , Numeric aperture-0.5 ,<0.17 dB/m @ 650 nm ,Bending loss <0.5 dB (r=20 mm, 90°) JIS C6861,Operating temperature--40 °C to +65 °C (-40 °F to 149 °F)making connections etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. |
| 42 | Projector -SITC Ceiling Mounting high white and with RGB segments colour output of upto 3000 Lumens projector; having aspect ratio 16:9, upto 1.6x Optical zoom lens,keystone range -+/-30 degree vertical (auto/manual) and +/-30 degree (manual), inputs – HDMI (2x) with HDCPCompatible,with resolution support from VGA (640*480) to 4K UHD (3840*2160), both USB A & mini B type,RS232 (x1) (DB-9 pin),DC 12V trigger(x1) Built in speakers 5-10W,Lamp replacement Cyscle -20000 Hrs in Eco Model and 10000 Hrs in Standard mode etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. |
| 43 | SITC of IP Main console deskwith Dual switched auto-sensing 10/100 Mbps Ethernet ports, integrated PoE,GRP2602W, Integrated dual-band Wi-Fi 802.11 a/b/g/n/ac (2.4Ghz & 5Ghz) ,132 x 48 (2.41’’) backlit graphical LCD display ,2 line keys with dual-color LED and support for 4 SIP account, 4 XML programmable context sensitive soft keys, 5 (navigation, menu) keys. 8 dedicated function keys for: MESSAGE(with LED indicator), TRANSFER,HEADSET, MUTE, SEND/REDIAL, SPEAKERPHONE, VOL+, VOL-, Hold, transfer, forward, 5-way conference, call park, call pickup, shared-call-appearance(SCA)/bridged-line-appearance(BLA), downloadable phonebook(XML, LDAP, up to 2000 items), call waiting, call log(up to 800 records), off-hook auto dial, auto answer, click-to-dial, flexible dial plan, hot-desking, personalized music ringtones and music on hold, server redundancy and fail-over ,Layer 2 QoS (802.1Q, 802.1P) and Layer 3 (ToS, DiffServ, MPLS) QoS ,Operation: 0°C to 40 AES based secure configuration file, SRTP, TLS, 802.1x media access control, UL & FCC/CE compliance.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with BSR 2021. |
| 44 | Supply, Installation, Testing & Commissioning of IP Phones1 SIP account, up to 2 callappearances TLS and SRTPsecurity encryptiontechnology to protect calls andaccountsDual switched auto-sensing 10/100 Mbps Ethernet ports, integrated PoE2 line keys with dual-color LED and 1 SIP account, 3 XML programmable context sensitive soft keys, 5 (navigation, menu) keys. 13 dedicated function keys for PAGE/INTERCOM, PHONEBOOK, MESSAGE, HOME, HOLD, RECORD, MUTE, HEADSET, TRANSFER, CONFERENCE, SEND and REDIAL, SPEAKERPHONE, VOLUME , call waiting,All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with BSR 2021. |
| 45 | SITC of IP PBXs appliance BOX with 500 Users Call Capacity along with 80 concurrent calls, upto 75 parties voice conference, inbuit 32GB Storage (for call recording), Network Interfaces : Three self-adaptive Gigabit ports (switched, routed or dual card mode) with PoE+, supports router mode and switch mode, Up to 5 layers of IVR (Interactive Voice Response). Call Features: Call park, call forward, call transfer, call waiting, caller ID, call record, call history, ringtone, IVR, music on hold, call routes, DID, DOD, DND, DISA, ring group, ring simultaneously, time schedule, PIN groups, call queue, pickup group, paging/intercom, voicemail, call wakeup, SCA, BLF, voicemail to email, fax to email, speed dial, call back, dial by name, emergency call, call follow me, blacklist/whitelist, voice conference, video conference, eventlist, feature codes, busy camp-on/ call completion, voice control. UL & FCC/CE compliance. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with BSR 2021. |
| 46 | SITC of E1/T1 Digital VOIP Gateway BOX for digital PSTN & ISDN trunks to be integrated with IP PBXs with VoIP network with 30 concurrent calls with Dual Gigabit autosensing RJ45 network ports, TLs and SRTP security encrption technology to protect calls and accounts, supports a wide range of voice codecs including G.722, G.729 iLBC, USB and SD card interface peripheral ports. UL & FCC/CE compliance All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with BSR 2021. |
| 47 | SITC of voice alarm Controller with Voltage 230/115VAC, 15%, 50/60 Hz Current inrush 8 A Max power consumption 600 VA Voltage 24 VDC, +15% / - 15% Current max 14 A Output power (rms/maximum) 240 W/ 360 W Power reduction on backup power -1 dB. Frequency response 60 Hz to 18 kHz (+1/-3 dB at -10 dB ref. rated output) Distortion <1% at rated output power, 1 kHz Bass control -8/+8 dB at 100 Hz Treble control -8/+8 dB at 10 kHz Mic/line input 1 x Connector XLR, 6.3 mm jack Sensitivity 1 mV (mic), 1 V (line) Impedance >1 kohm (mic); >5 kohm (line) S/N (flat at max volume) >63 dB (mic); >70 dB (line) S/N (flat at min volme/muted) >75 dB CMRR >40 dB (50 Hz - 20 kHz) Headroom >25 dB Speech filter -3 dB at 315 Hz, high-pass, 6 dB/oct. etc as req. The OEM should have EN/CE/UL complied certification. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. refer Annexure "A" attached with Electric BSR. |
| 48 | SITC of Router 12 loudspeaker outputs (Zone) Two external amp inputs Call output Six volume override . outputs 12 trigger inputs RS-232 connector. Two system interlinks Two external amp outputs (XLR/balanced) Power amp fault output 24 VDC power . output 24 VDC power input power supply Voltage 230/115 VAC, Activation Programmable Supervision On EMG inputs, programmable Supervision method Series / parallel resistor 100 V input Connector MSTB 2,5 /16-ST Amp 1 100 V70 V/0 V Amp 2 100 V/0 V Power handling capacity 1000 W Loudspeaker outputs 12 x (2 x 6 zones) Connectors MSTB 2,5 /16-ST, floating 100 V output 700 W rated per zone Volume override types 3-wire, 4-wire (24 V), 4-wire failsafe Output Contacts Connector MC 1.5/14-ST-3,5 Rating 100 V, 2A, voltage free General purpose relays (2x) NO/COM.etc as req. The OEM should have EN/CE/UL complied certification. All as per pre. approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with Electric BSR |
| 49 | SITC of 480 W power amplifier in a compact housing 70 V/ 100 V and 8 ohm outputs Dual inputs with priority switching 100 V input for slave operation on 100 V speaker line Temperature controlled front to back ventilation, Input Voltage 230VAC +10% at 50/60Hz or 24VDC ±10%, Inrush Current - 8A at 230 VAC, 6A at 24 VDC, Rated Output (RMS)- 120W,100 V, 70 V, 8/4 ohm >25 dB (50 Hz to 20 kHz),Max power- 274W, Pilot tone- 41 Wdirectly stackable.etc as req. The OEM should have EN/CE/ULcomplied certification. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure "A" attached with Electric BSR |
| 50 | SITC of 6 Zone Voice alarm Call Station Table top Voltage Range 18 to 24 V (24 V supplied by LBB 1925/10) Current consumption <30 mA Maximum input sound level 85 dB SPL Gain preset +6/0/-15 dB Limiter threshold 2 V Compression ratio limiter 1:20 Distortion <0.6% (maximum input) Input noise level (equiv.) 25 dB SPLA Frequency response 100 Hz to 16 kHz Speech filter -3dB @315 Hz, high-pass, 6 dB/oct Output impedance 200 ohm Chimes 18 different combinations Priorities 2 different priorities Cable length 5 m (16.4 ft) with additional key pad to select upto six additional zones.etc as req. The OEM should have EN/CE/UL complied certification. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with Electric BSR |
| 51 | SITC of Mixer cum Amplifier :4 microphone / line inputs, plus music source input3 models in a wide range of output power 120W-240W2-tone chime Insert feature to use as a pre/power amplifier VU meter to indicate output level; Limiter circuit for protection, 50 -60 Hz to 20 kHz (+1/-3 dB @ -10 dB ref. rated output), Max. ± 8 dB , S/N Ratio 60dB ,Inbuilt Bluetooth for audio streamingSupports audio playback from USB pen drive making connections etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached with BSR. |
| 52 | SITC of Freestanding Gooseneck Mic with base Connector Voltage range 12 to 48 V Current consumption <8 mA Sensitivity 0.7 mV @ 85 dB SPL (2 mV-1V/Pa) Maximum input sound level 110 dB SPL Distortion <0.6% (maximum input) Equivalent input noise level 28 dBA SPL (S/N 66 dBA ref. 1 Pa) Frequency response 100 Hz to 16 kHz Output Impedance < 200 ohm Cable length 2 m (78 in) Connector 5-pin DIN 180° (lockable).making connections etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached withBSR. |
| 53 | SITC of boundary layer microphone Connector Type 3-pin XLR Frequency Response (-3 dB) 50 - 20,000 Hz Polar PatternOmni, Cardioid, S-cardioid & Figure 8 Mic Type Boundary Element Dual condenser (back-electret) Impedance, Low-Z balanced 200O Open Circuit Voltage31.5mV/Pascal Case Material any phantom Power Requirement 9 - 52 VDC.Etcmaking connections etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached withBSR . |
| 54 | SITC of 4 - 6" 2-Way Full Range Coaxial Ceiling Main Loudspeaker, Professional Series; having Frequency response (-10 dB): 65 Hz - 20 KHz; Coverage (conical): 130°; Power handling: 50 -60 W cont. / 200 W peak; Sensitivity (SPL 1W/1m): 86-87 dB; Max calculated SPL: 103 dB cont. / 109 dB peak; Impedance: 8 Ohms nominal (transformer bypass); Network & Transducers Protected: 12 dB/oct 3.3kHz ; LF transducer: 4 in (100 mm) Polypropylene cone; HF Transducer: 75in. (19mm) Ti Mylar Laminate;Transformer Taps: 70V: 1.5W to 60W, 100V: 3W to 60W; Bypass :8O; Connectors: C4.2:Phoenix type removable, with screw terminals and "loop -thru", accepts 12 ga wire; C4.2D: Fire-safety rated input block, 3 terminal barrier strip accepts 12 ga wire; Enclosure Material: Baffl e - UL 94V-O rated ABS Backcan - Zinc plated steel; Safety agency ratings: UL-1480;IP rating: 54 or better.making connections etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached withBSR . |
| 55 | SITC of Conference Cable XLR Wire -Copper, stranded 1 mm2 .<0.018 ohm/m Fiber -PMMA, 1 mm , Numeric aperture-0.5 ,<0.17 dB/m @ 650 nm ,Bending loss <0.5 dB (r=20 mm, 90°) JIS C6861,Operating temperature--40 °C to +65 °C (-40 °F to 149 °F)making connections etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure "A" attached withBSR. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
