Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 03-10-2023 | Date extend | Date | 05-10-2023 |
| Sl. No. | Item Description |
| 1 | 15 ??.??. ?? ??? ????? ????? ???? ?? ??? ?? ??????? (Dressing) ??? ???????? ??? ???? ????? ?? ????? ??? ?????? ?????? ?? ???? ???? ?? 1.5 ???? ???? ??? 50 ???? ???? ?? ?????? ?????? /????/?????? ????? ??? BSR Ref#1(?) |
| 2 | ???, ???,?????? ??? 1.5 ????? ?? ?????? ?? ????? ???? , ?? ?? ????? , ???? ?????, ??? ?? ??????? , ???? ?????? ?? ???? ???????, ??? ???? ?? ??? ???? ???????? ?? ???: ?????? ?? ???? ??? ??? ??? ????? ?? 50 ???? ?? ???? ?? ????????? ???? ?????? ?????? BSR Ref#2(?) |
| 3 | ???????? ???????? ???? ?? ???? ??? 40 ??.??. ????? ??? ?? ??????? ??????(crusher broken)/?? ????? , ????????- ??? ????? ??? 1 ???????? : 4 ??? : 8 ?????? ?????? ??? ????? ??? ????? ???? , ???? ???? ? ???????? ???????? ???? ?? ???? ??? 40 ??.??. ????? ??? ?? ??????? ??????(crusher broken)/??????? ?? ?????? (crusher broken) ?? ??? ?????? ?? ?????? (crusher broken) ?? ??? 40 ???? ?????? ?????? ????? ?? ????? ?? ????? ?? ??? ?? ???? ??? ???? ?? ????? ???? ?? ??? ?????? ??? ???? ?????? ????? ?? ?? ??? 30 ??????? ?? ????? ?? ??????? BSR Ref#10(?) |
| 4 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).BSR RefPWD BSR 3.1.4 |
| 5 | Anti termite treatment of floor using Imidacloprid 30.5% EC non repellent, odorless, low dose, environmentally safe terniticide with rapid action non corrosive stain free, by drilling 12mm diameter holes 300mm apart injecting the emulsion as per specification and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area DPE 12mm dia termitube system with required number of junction boxes are to be installed. The termitube will run all along the perimeter wall both inside and outside. In the middle area the termitube to be installed at an interval of 1.00 Mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. After successful testing of termitube, pesticide emulsion of imidacloprid 30.5% EC mixed with water in the ration of 1:474 will be pumped by a otorizedspray pump from the junction box in specified manner. The plinth area of the area treated will be measured for paymentBSR RefPWD BSR 1.39 |
| 6 | ???? ??? ?????? ??? ?????? ?? ?? ?????-???? ??????-???? ????? ???, ?? ??? ?? ???? ????? ???? ??? ???? ??? ????? ?????? ???? 1:6 BSR Ref#29(?) |
| 7 | ???? ??? ??????/??? ?? ??? ??? ??? ?????? ??? 50 ???? ?? ???? (Lead) ??? ????? ??? ???? ???? , ???? ????? ??? ?????? ?? ?????? BSR Ref5 |
| 8 | ????? ?? ??????? ???? ?? ??? ?????? ??????? ?? ?????, ?????? ? ???????? ???? | (?????? ?? ?????? ?????? ??? ?? ???? ?? ?????? ? ?? ??? ????? ??) 5 ??.??. BSR Ref#29 |
| 9 | ???? ?? ???? ???? ????? ???? 15 ???? ???? ???????? ?? ??????? ??? ????? ????? ?? ????? ?????? BSR Ref65 |
| 10 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excludingthe cost of centering, shuttering and reinforcement Add extra for providing richer mixes respectively at all floor levels Providing M-25 grade concrete by using cement as per codal provision instead of M-20 grade design mix.BSR RefPWD BSR 4.1+4.6.1 |
| 11 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plint and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. M20 grade Nominal Mix / Design Mix Add extra for providing richer mixes respectively at all floor levelsBSR RefPWD BSR 4.1+4.6.1 |
| 12 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excludingthe cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix Add extra for providing richer mixes respectively at all floor levelsBSR RefPWD BSR 4.3+4.6.1 |
| 13 | ??????????\"?????? (????? ??? ????????) ?? ??.??.??. ??, ??????, ??????, ??????? ??? ????? ?? ??? ????? 4.5 ???? ???? ?? ?? ??? ??? ????? ??? ????? ????? ?? ?????? ?????? ????? BSR Ref#93(?) |
| 14 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. Thermo-mechanically Treated bars (Conforming of relevent IScode)FE500BSR RefPWD BSR 4.13.3 |
| 15 | ???? ??? ?????? ????? ?????? ??? ?? ????? ???????? -???? 1:6 ?? 1:8 ????? ???, ?? ??? ?? ???? ????? ???? ??? ???? ????? ???????? ????? 1:6 ????????? ???? ??????? ??? ????? ????? ??? 4.5 ???? ????? ?? ?????? ????? ??? BSR Ref#20(?)+22 |
| 16 | ????? ?????? ?? ????? ?? 112 ???? ??? 75 ???? ????? ??? ???? ??? ??????? ??? ??????-???? ????? 1:4 ??? ????? ?? ????? ???? ?? ???? ??? 112 ???? ????? ??? BSR Ref#23(?) |
| 17 | ?????? ?????????? ????? ?? 1:6 ?????? ??? ??????-???? ?????? ?????? ?? ??????? ??? 14 ??? ?? ?????? ???? ????? 20 ???? eksVkbZ dk IykLVj eas vkjlhlh dkWye@chae ,ao fpukbZ das tksMks dks ok;j es\"k ¼eqxkZ tkyh½ ls doj djrs gq;s ¼eqxkZ tkyh dh ykxr jkf\"k lfgr½ BSR Ref#77 (?) |
| 18 | 50 ???? ????? ??? ?????? ??????? 1:2:4 ?????? ?????? 1 ?????? 2 ???? 4 ?????? ?? ?? ??? ?? 12 ??. ????? ?????? ?? ??? ?????? ?????, ?????, ????? ??? ???? ??? ????? ?????? ?? ?????? BSR Ref#14(?) |
| 19 | Providing and fixing pressed steel mitred door frames manufactured from commercial mild steel sheet of 1.25 mm (16 gauge) thickness including hinges jamb, lock jamb, head and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25 mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge. Profile \"C\"BSR RefPWD BSR 9.6.2 |
| 20 | ????????? ??? ????? ??? ??? ???, ??? ?????? ?? 30 ???? ?????? ????? ????? ?? ????????? ????? ??, ?????? ?? ?????? (beading) ??????, ?? ????? ??? ?? ?????? ?? ???, ?????? ?????? 3 ??????? ?? ?????? ?? ????? ??? ??????? ????? ????????? 1X2 ???????? ?????? ?? ??? ? BSR Ref84 |
| 21 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to thealuminium window by Aluminium beading 20x3mm with suitablescrews not exceeding 150mm distance at all heights with all lead andlift with scafolding.BSR RefPWD BSR 16.11 |
| 22 | Providing and fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutter 25 mm to 40 mm thick 5 mm reflected glass BSR RefPWD BSR 8.6.17 |
| 23 | Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20x10x2mm and brackets with flat iron diagonals 20x5mm, size with top and bottom rail of T-iron 40x40x6mm, with 40 mm dia steel pulleys / ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension). IS 10521-1983. With 75 mm opening when closed.BSR RefPWD BSR 9.10 |
| 24 | Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approvedmake conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately).aluminum (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approvedAnodizer)BSR RefPWD BSR 16.1.2.1 |
| 25 | Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). For fixed portion Anodised aluminum (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approvedAnodizer)BSR RefPWD BSR 16.1.1.1 |
| 26 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVS/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost. of aluminium snap beading shall be paid in basic item.) With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm)BSR RefPWD BSR 16.5.2 |
| 27 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed inaluminium doors ,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge Pre-laminated particle board with decorative lamination on one side and balancing lamination on other sideBSR RefPWD BSR 16.4.1 |
| 28 | ?????/??? ??? ??? ???? ?? ????? ?????? ???? ??????, ?? ??? ??????? (????), ?? ?????, ?????? ??? ????? ???? BSR Ref#63 |
| 29 | Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Grade 304BSR RefPWD BSR 16.56.a |
| 30 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, SillsCounters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Jhunjhunu / Jalore (Red/Choclate/Black/Pink Colour) Above 3601 Cm2 SlabsBSR RefPWD BSR 7.5.1 (iii) |
| 31 | Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite/Kota Stone Work Full Edge mouldingBSR RefPWD BSR 7.6.2(i) |
| 32 | 20 ???? ????? ??? 1:4 ?????? ???? ????? ?? ??? ????? ???? ?????? ????, ???????? ?? ????? ? ????? (??????? 3 ???)??? ?????? ?? ?????? ?? ??? ?? ?? ?? ?????? ???? 2300 ???? ???? ?? ????BSR Ref#67(??) |
| 33 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades ceramic glazed vitrified tiles with water absortion less than or equal to 0.08% confirming to IS:13753 & IS : 15622 on walls, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). Size 600mm x 1200mm BSR RefPWD BSR7.20.1 |
| 34 | Providing and fixing 1st quality MAT & GLOSSY finished ceramic tile confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4) Size 600mm x 600mmBSR RefPWD BSR7.21.5 |
| 35 | Providing and Fixing at all height all false ceiling of 12.5 mm thick tapered edge Gypsum board conforming to IS : 2095 including providing and fixing of frame work made of special section power pressed from M.S. sheet and galvanized in accordance with zinc coating 600 as per IS : 277 and consisting of angle cleats of thick 25 mm wide x 16 mm thick with flanges of 22 mm and 37 mm at 1200 mm center to center oneflange fixed to the ceiling with dash fastner 12.5 mm dia x 40 mm long with 6 mm dia bolts to the hangers of 25x25x5mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45 mm x 15 mm x 0.9 mm running at the rate of 1200 mm center to center to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450 mm center to center shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm dia x 230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall / partition withthe help of rawl plugs at 450 mm center to center with 25 mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of gypsum board with recommended filler paper tapes, finisher and two coats of primer suitable for gypsum board as per manufactures specifications and also including the cost of making openings for right fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specifications and direction of the Engineer-in-charge but the excluding the cost of painting.the perimeter of ceiling fixed to wall / partition withthe help of rawl plugs at 450 mm center to center with 25 mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of gypsum board with recommended filler paper tapes, finisher and two coats of primer suitable for gypsum board as per manufactures specifications and also including the cost of making openings for right fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specifications and direction of the Engineer-in-charge but the excluding the cost of painting.the perimeter of ceiling fixed to wall / partition withthe help of rawl plugs at 450 mm center to center with 25 mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of gypsum board with recommended filler paper tapes, finisher and two coats of primer suitable for gypsum board as per manufactures specifications and also including the cost of making openings for right fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specifications and direction of the Engineer-in-charge but the excluding the cost of painting.the perimeter of ceiling fixed to wall / partition withthe help of rawl plugs at 450 mm center to center with 25 mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of gypsum board with recommended filler paper tapes, finisher and two coats of primer suitable for gypsum board as per manufactures specifications and also including the cost of making openings for right fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specifications and direction of the Engineer-in-charge but the excluding the cost of painting.the perimeter of ceiling fixed to wall / partition withthe help of rawl plugs at 450 mm center to center with 25 mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of gypsum board with recommended filler paper tapes, finisher and two coats of primer suitable for gypsum board as per manufactures specifications and also including the cost of making openings for right fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specifications and direction of the Engineer-in-charge but the excluding the cost of painting.the perimeter of ceiling fixed to wall / partition withthe help of rawl plugs at 450 mm center to center with 25 mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of gypsum board with recommended filler paper tapes, finisher and two coats of primer suitable for gypsum board as per manufactures specifications and also including the cost of making openings for right fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specifications and direction of the Engineer-in-charge but the excluding the cost of painting.the perimeter of ceiling fixed to wall / partition withthe help of rawl plugs at 450 mm center to center with 25 mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of gypsum board with recommended filler paper tapes, finisher and two coats of primer suitable for gypsum board as per manufactures specifications and also including the cost of making openings for right fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specifications and direction of the Engineer-in-charge but the excluding the cost of painting.BSR RefPWD BSR 10.27 |
| 36 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete New Plastered Surface (three or more coats)BSR RefPWD BSR 12.22.1 |
| 37 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: New work (two or more coats) over and including scrapping and priming coat with cement primer.BSR RefPWD BSR 12.37.1 |
| 38 | Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: New work (Two or more coats applied @ 3.84 kg/10 sqm).BSR RefPWD BSR 12.41.1 |
| 39 | ?????? ?????? ?? ??? ???? 3 ?? ??? ???? ????? ??? ?? ???? (To give even shade) ??? ?????/?????? ????? ?? ?? ????? ?????? ??? ????? ??? BSR Ref#82(?) |
| 40 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)BSR RefPWD BSR 3.1.4 |
| 41 | Providing & laying broken glazed titles on roof ( broken glazed tiles not less than 9 Kg/Sqm) on top of hot bitumen @ 1.7 Kg/Sqm. (1.40 Kg of VG-40 (30/40 )grade and 0.30 Kg/Sqm. Of VG-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of Engineerin-chargeBSR RefPWD BSR 10.24 |
| 42 | Part - B SANITARY WORK |
| 43 | ???????? ????????? (?????????.??.) BSR Ref#175(?) |
| 44 | ?????? ???? ???? ???? ?????? ?? ???????? (?????????.??.) ???? 530X410 ???? ? BSR Ref#175(?) |
| 45 | ???? ??? ???? ?? ??????? ?? ????? ??? ???? ???? ???? ???? ???? ?????? ?? ??????, ?????????(???? 430X350X300 mm) , ???? ??????? ??? 25 ???? ?? ?????? ???? ?? ???? ????? ??? ?????????? ????? BSR Ref177 |
| 46 | 450X300 ???? ???? ?? ???? ???? ???? ?????? ?? ??? ???? (????????) ?? ?????? ???? ?????? ?????? ???? ???, 15 ???? ?? ????? ??? ??? 32 ???? ?? ???? ????? ?????? ?????? ??? 25 ???? ?????? ?? ?????? ???? ?? ?????? ???? ????? ? ?????????? ????? BSR Ref178 |
| 47 | P & F W.V.C. Urinal Partition Plate of approved standard make of size 630x315mm including making good the wallBSR RefPWD BSR 1.15 |
| 48 | P&F looking mirrors with PVC frame of approved (atul/equivalent) Size Oval shape 450x350 mmBSR RefPWD BSR -1.45.2 |
| 49 | PP & F Low level Flushing Cistern of 10 litres capacity (IS : 2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball (IS: 1703 mark) complete including cutting and making good the wall: PVC with PVC bend and superior internal fittings as per IS : 7231 .BSR RefPWD BSR -1.20.3 |
| 50 | P & F Premiumquality water closet Seat Covers with brass hinges complete Solid PVC (ISI marked) grade-I White for EWCBSR RefPWD BSR -1.72 |
| 51 | Jet Spray (Premium heavy Quality) as approved by Engineerin-ChargeBSR RefPWD BSR -2.33.23 |
| 52 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brassthreaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete asper direction of Engineer in Charge. (Internal work Exposedon wall)BSR RefPWD BSR -2.37 |
| 53 | a)20mm diaBSR Ref2.37.2 |
| 54 | B) 25 mm diaBSR Ref2.37.3 |
| 55 | C) 50mm diaBSR Ref2.37.6 |
| 56 | P & F Bib Cock (IS : 8931 Mark), Superior quality ofapproved make: Long body, 15mm nominal bore weight not less than690 gmBSR RefPWD BSR -2.7.4 |
| 57 | P & F Stop Cock (IS :8931 Mark), superior quality & oapproved make: 750 gm. 20 mm nominal boreBSR RefPWD BSR -2.8.2 |
| 58 | P & F Inlet Connection (Angle Valves) Superior quality, ofapproved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.BrassBSR RefPWD BSR -2.12.1 |
| 59 | Providing and fixing unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type `B\" for sciland waste dischareg system (IS : 13592: 1992 marked) of approved quality/ make. Nahni Trap with Jali 4\"BSR RefPWD BSR -3.45.26 |
| 60 | P&F towel rail or ring of approved quality /make: C.P. brass Towel rail elbow type with concealed screws size 600mm (heavy duty)BSR RefPWD BSR -1.47.2 |
| 61 | P&F Grating of approved quality/ make Synthetic material (PTMT) of approved quality/ make size 125mm diaBSR RefPWD BSR -1.48.1 |
| 62 | Providing Laying & Jointing R.C.C. class NP-2 Non-Pressure pipes (IS:458 mark) of approved make with collars, jointed with C.M.1 : 2 or having Spigot and socket ends with flexible rubber rings joint including testing of joints etc. complete 200mm dia Internal. BSR RefPWD BSR -3.8.3 |
| 63 | P & F Flush Cock/Flush Valve (IS:9758 Mark) or WC of approved quality make : Brass / Gun metal Half-turn wt. 1 Kg. of approved quality / make, 25 mm nominal bore.BSR RefPWD BSR -2.14.3 |
| 64 | P & F Full-way valve (IS:778 Mark) or wheel valve of approved make :BSR RefPWD BSR -2.15 |
| 65 | a) Gun-metal 15 mm nominal bore.BSR RefPWD BSR -2.15.1 |
| 66 | b) Gun-metal 25 mm nominal bore.BSR RefPWD BSR -2.15.3 |
| 67 | P&F extension pipe for bib cocks of approved quality/ make: C.P. brass of Heavy & superior quality 50x15mmBSR RefPWD BSR -1.56.1 |
| 68 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 1000litres capacity.BSR RefPWD BSR -2.26.5 |
| 69 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 2000litres capacity.BSR RefPWD BSR -2.26.6 |
| 70 | P&F rigid PVC Pipe (IS:4985 mark) class II(4 Kg. /Cm.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant 110mm diaBSR RefPWD BSR -3.16.3 |
| 71 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant:BSR RefPWD BSR -3.17 |
| 72 | a) Door Tee 110mmBSR Ref |
| 73 | b) Bend 45 110mmBSR Ref |
| 74 | c) Bend 87.5 110mmBSR Ref |
| 75 | d) Vent Cowel 110mmBSR Ref |
| 76 | e) Pipe clip 110mmBSR Ref |
| 77 | f) WC connector with lipring 110mmBSR Ref |
| 78 | g) Plain floor trap 110mmBSR Ref |
| 79 | h) Gully Trap 110mmBSR Ref |
| 80 | P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor : 1.0 mm thick stainless steel AISI -304 & IS 13983-1994 kitchen sink of approved make as per Engineer-in-charge with large waste coupling 18 x 16 x 6 16x14x6BSR RefPWD BSR -1.38.9.1 |
| 81 | Construction of chamber in all type of soil with 300 mm thick masonry in Cm 1:6 m 100mm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr.-do- size 450 x 450mm upto depth of 0.5m & 15Kg CI cover with frameBSR RefPWD BSR -3.21.2 |
| 82 | Construction of soakage well in all type of soil 300 mm thick dry masonry top and bottom 300 mm course in CM 1:6, 80 mm thick stone slab, jointing of slab in CM 1:3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C. flooring, earth work complete as per approved drawing including disposal of earth within a lead of 50 mtr. :Size 300 Cm. dia outside & 300 Cm. depth .BSR RefPWD BSR -3.22.1 |
| 83 | Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M- 15 grade C.C floor & RCC slab covering with M15 grade c.c floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:- Size 400 x140x150 cm.(for 50 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 10mm f @15 cm c/c bothways including shuttering complete in all respectBSR RefPWD BSR -3.27.3 |
| 84 | PART -C -ElectricWorks |
| 85 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it\"sISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 1.1 |
| 86 | Short point (up to 3 mtr.)BSR 2022 1.1.1 |
| 87 | Medium point (up to 6 mtr.)BSR 2022 1.1.2 |
| 88 | Long point(up to 10 mtr.)BSR 2022 1.1.3 |
| 89 | Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) inrecessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it\"s ISI marked (IS:3419-1988)accessories, Hot Dipped GalvanizedModular box of 1.2 mm thick with earth terminal, 10 A modularswitch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 1.3 |
| 90 | On boardBSR 2022 1.3.1 |
| 91 | Short point (up to 3 mtr.)BSR 2022 1.3.2 |
| 92 | Medium point (up to 6 mtr.)BSR 2022 1.3.3 |
| 93 | Long point(up to 10 mtr..)BSR 2022 1.3.4 |
| 94 | S&F following sizes (dia.) of ISI marked medium duty PVC conduit along with accessories in surface / recessed using saddles, clamps, fastener as required includingcutting the wall, covering conduit and making good the same as required.Gr IBSR 2022 |
| 95 | 20 mmBSR 2022 1.4.1 |
| 96 | 25 mmBSR 2022 1.4.2 |
| 97 | 32 mmBSR 2022 1.4.3 |
| 98 | BSR 2022 |
| 99 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 4.1 |
| 100 | 2 x 1.5 sq.mmBSR 2022 4.1.2 |
| 101 | 3x 1.5 sq.mmBSR 2022 4.1.3 |
| 102 | 2 x 2.5 sq. mm. + 1x1.5sqmmBSR 2022 4.1.7 |
| 103 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.BSR 2022 4.1.14 |
| 104 | 4 x 10.0 sq.mmBSR 2022 4.1.23 |
| 105 | Supplying and drawing PE Insulated & PVC Sheathed unarmoured telephone cable with 0.5 mm dia. Solid Annealed electrolytic grade bare Copper Conductor as per IS: 8130/84 &confirming to TEC specification GR / WIR/06-03 March 2002in existingsurface or recessed conduit/casing capping. including ferruling on each pair for Identification etc. as required. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 4.3 |
| 106 | 2 pairBSR 2022 4.3.2 |
| 107 | Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 6.1 |
| 108 | Metal door (single phase) IK-09 and IP-43 with Metal end boxBSR 2022 6.10.1 |
| 109 | 8 Way (8+2)BSR 2022 6.10.1.3 |
| 110 | Metal door (Three phase) IK-09 and IP-43with Metal end boxBSR 2022 6.10.3 |
| 111 | 6 WayBSR 2022 6.10.3.2 |
| 112 | BSR 2022 |
| 113 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 6.1 |
| 114 | Single pole MCB (With B/C curve tripping Characteristics)BSR 2022 6.1.1 |
| 115 | 6 A to 32 A ratingBSR 2022 6.1.1.2 |
| 116 | Double pole MCB(With B/C curve tripping Characteristics)BSR 2022 6.1.2 |
| 117 | 6 A to 32 A ratingBSR 2022 6.1.2.2 |
| 118 | Triple pole MCB(With B/C curve trippingCharacteristics)BSR 2022 6.1.3 |
| 119 | 50/63 A ratingBSR 2022 6.1.3.4 |
| 120 | Four pole MCB (With B/C curve tripping Characteristics)BSR 2022 6.1.4 |
| 121 | 40 A ratingBSR 2022 6.1.4.3 |
| 122 | 50/63 A ratingBSR 2022 6.1.4.4 |
| 123 | Providing & Fixing of Recessed/surface mounting heavy duty Vertical TPN Distribution board with Metal end box with provision of incomer suitable for 3/4 pole MCCB and SP / TP MCB as outgoing ,made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powder painted with reversible door (for double door DB only ) complete with insulated 160 (upto 160 A Incomer) / 250 Amp. copper bus bar, neutral bars with shrouds, earth bar , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 6.16 |
| 124 | Double door IP-43 & IK-09 with Provision of Incomer MCCB 100/ 125 A Rating with Metal end boxBSR 2022 6.16.1 |
| 125 | 4 WayBSR 2022 6.16.1.1 |
| 126 | SITC of3 /4pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440/415 V, 50 Hz; O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator,line load interchangeability,designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree,pollution degree 3, having positive isolation capability, push(test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage690 V.provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.OEM shall have submitNABL / CPRI / ERDA accrediated lab type test certificate before execution All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 9.3 |
| 127 | 4 pole MCCB With Thermal Magnetic releaseBSR 2022 9.3.3 |
| 128 | up to 100 Amp , 25 kA, adjustable O/L & adjustable S/C setting, BSR 2022 9.3.3.2 |
| 129 | 125 Amp , 25 kA, adjustable O/L & adjustable S/C setting, BSR 2022 9.3.3.3 |
| 130 | P & F of Industrial plug and socket conforming to IEC 60309-1/2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 6.14 |
| 131 | IP - 67 Plug topBSR 2022 6.14.4 |
| 132 | 32 A 3 pin(2P+E)BSR 2022 6.14.4.2 |
| 133 | Providing & Fixing of modular type switch/ bell push duly ISI marked (IS :3854) with CM/L no. printed and made out of unbreakable and fire retardant vergin UV Stabilized Polycarbonatewith brass terminals and captive screws & silver alloy contact tipwith IP-20 rating ,minimum width ofswitch toggle( PUSH PART ) should not less then 20mm,includingall as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR BSR 2022 7.27 |
| 134 | 10 A one way switch BSR 2022 7.27.1 |
| 135 | Providing & Fixing of modular type lockable feature socket dulymade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating , includingall as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 7.28 |
| 136 | 6 A3/5 pin shuttered socketBSR 2022 7.28.1 |
| 137 | Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating ,includingall as per pre approved by Engineer in charge,making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 7.29 |
| 138 | 5 step fan regulator 2 Module 360 dgree rotatingBSR 2022 7.29.1 |
| 139 | Providing & Fixing of following modular accessories as per PWD specification for electrical Works,made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating , includingall as per pre approved by Engineer in charge,making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 7.30 |
| 140 | RJ-11 telephone jack Double lineBSR 2022 7.30.2 |
| 141 | Blanking plateBSR 2022 7.30.6 |
| 142 | Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification ofWiring accessories refer ChapterE - 07related item & For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 7.37 |
| 143 | BSR 2022 |
| 144 | P & F Krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted,including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 7.38 |
| 145 | 10 PairsBSR 2022 7.38.1 |
| 146 | 20 PairsBSR 2022 7.38.2 |
| 147 | Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 15.7 |
| 148 | 1200 mm Sweep BEE 1 Star rated (service value >=4.0 to < 4.5 )BSR 2022 15.7.1 |
| 149 | P & F 1.2mm thickM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 15.1 |
| 150 | Providing & Fixing ofof Double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making connections, testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 15.11 |
| 151 | 225 mm sweepBSR 2022 15.11.1 |
| 152 | Supply , Installation, Testing and Comissioning ofInverter type Air Cooled Hi Wall split type Air conditioners with latest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R-410 Green Refrigerant, wireless Remote control, suitable for working between 230V +/- 10% with low & high voltage cutoff and50 hz , single phaseACsupply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . 2.0 TR ISEER not less then 4.6BSR 2022 22.24.8 |
| 153 | Meeting hall+ VC room (4+1)BSR 2022 |
| 154 | BSR 2022 |
| 155 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy = 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.=0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 17.1 |
| 156 | 1170mm(+/-10%) LED batten with min. lumen output 2200 lmBSR 2022 17.1.1 |
| 157 | Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / SqaureSMD Mid Power LED Downlight with power coated die-cast aluminum housingwith UV Stabilized non yellowish Diffuser withBIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% . System Lumen efficacy of = 110 lm / watt, THD < 10 % , Pf.=0.95, CRI >80,life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing.BSR 2022 17.3 |
| 158 | OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 |
| 159 | Surface Mounting (with extruded alumn. Housing )BSR 2022 17.3.2 |
| 160 | Minimum lumen output 1300 lmBSR 2022 17.3.2.2 |
| 161 | Minimum lumen output 2400 lmBSR 2022 17.3.2.4 |
| 162 | Providing & Fixing of IP20, 2\"x2\" LED Surface/ Recessedmounting Mid power SMD type LED Light fixture not less than 50mm housing depth made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 4 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection(Integral with light fixture). System lumen efficacy of = 120 lm/Watt ,THD < 10 % , p.f.=0.95,CRI >80 ,life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. BSR 2022 17.4 |
| 163 | OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 |
| 164 | Recessed MountingBSR 2022 17.4.1 |
| 165 | Minimum lumen output 4200 lmBSR 2022 17.4.1.3 |
| 166 | Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass coverand secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver& has a unique BIS R number withInput Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driverEfficiency >85%,THD(I) <10%Humidity 10% to 90% RH Working Temp -5C to 45C .driver current <750mA. The luminaireshall be BIS certified and Trade mark certified. Life ExpectancyEqual or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min = 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs.Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities forLED fixtures.(LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 18.12 |
| 167 | LED Street Light fixture with Minimum lumen output 5600 lm BSR 2022 18.12.3 |
| 168 | Providing & Fixing of IK10IP65 protected 600 mm height LED Bollard Luminarie with base platemade of powder coated die cast alluminium housing with UV stabalized PC diffuser. The System level Luminous efficacy =90 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N)and efficiency > 85%, PF>0.9, THD<20% and input Voltage range of 90-270V AC at 50Hz. System life of 30000 Burning hours with 70% of Initial Lumens maintainedLight output in Cool white or Warm White Colour as per engineers choice. driver current <750mA.Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities forLED fixtures.(LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 18.13 |
| 169 | Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected byPVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . BSR 2022 20.1 |
| 170 | Supply and Installation of unsheilded/360 degree sheilded Information outlets made of high impact plastic body with ABS, FR Grade halogen free material with provision for protection against dust in jack, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact termination on reliable copper tin plated Insulation displacement contact, with easy lock mechanism, It supports IEC 60603-7-4 and complied with ANSI/TIA/EIA 568 C.2 standard. jack should be RJ11,RJ12 & RJ45 compatible. Should support Ethernet 1.2 Gb/s ATM,Digital video and broadband/baseband analog video, Voice over internet protocal (VOIP) Specifications in existing modular/MS Boxes along with necessory connections as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . BSR 2022 20.4 |
| 171 | Cat 6, Un-sheilded Information OutletBSR 2022 20.4.1 |
| 172 | Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture ,material should bePC+ABS body, Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. OEM. Dimensions should be 86mm X 86mm as required complete in all respect.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . BSR 2022 20.5 |
| 173 | Single ApertureBSR 2022 20.5.1 |
| 174 | Dual ApertureBSR 2022 20.5.2 |
| 175 | Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A /Class E/Ea patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors with strain relief boots as per ANSI/TIA/EIA 568-C.2 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568C.2, ISO/IEC 11801, EN 50173, IEC 60603-7-51, EN 60603-7, IEEE 802.3an minimum requirement for 1G BASE-T to 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, should support IEEE 802.3af / IEEE 802.3at for POE applications, Minimum 750 to 1000 mating cycles in plug contacts for long durability, Should support Ethernet 10GBASE-T, 1.2 Gb/s ATM, Token ring 4/16, Digital video and broadband/baseband analog video, Voice over internet protocal (VOIP).All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . BSR 2022 20.7 |
| 176 | Cat 6, U/UTP (Unscreened/Un-sheilded Twisted Pair) Patch CordBSR 2022 20.7.1 |
| 177 | 1 MtrBSR 2022 20.7.1.2 |
| 178 | 2 Mtr BSR 2022 20.7.1.3 |
| 179 | Providing & Fixing ofWiring Accessories OEM fabricated following size GI box of 1.2 mm thick with earthing terminal and adjustable floating clamp in recess/ surface suitable for modular accessories as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 7.32 |
| 180 | 1-2 ModuleBSR 2022 7.32.1 |
| 181 | BSR 2022 |
| 182 | Supply & Installation of IP-20 & IK-08 , UL ListedWall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door,Vertical Mounting Rail 1.6 MM with \"U\"Marking , with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19\" angles with wall mounting provision on wall. Accessories like: 1 No of 19\" 1U Horizontal Cable manager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of 19\" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with Suitable Anchor fastneretc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . BSR 2022 20.16 |
| 183 | 9 U Rackwith Width 600 mm & Depth 400 mm + 100 mm BSR 2022 20.16.2 |
| 184 | Supply, Installation, & Testing of 19\" 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated, Singlemode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable duplex adapters for ST/E-2000/SC/LC/MT-RJ/PC type, It should have easy removable Top plate with push buttons, there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores, splice tray should be PC+ABS material, it should include accessories like mounting hardware, gormetts, heat shrink tubes/sleevs, screws, nuts to install the panel for rack/wallmount applications as per requirment complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 20.15 |
| 185 | 24 PortsBSR 2022 20.15.3 |
| 186 | Supply , Installation, Testing and Comissioning ofManaged Layer-2 Intelligent 10/100 Ethernet Switch providing 24 x 10/100/1000 MBPS Giga Ethernet ports / with min 2 SFP Giga Ports (provision for Fiber Giga connectivity) with related LAN Base Software including making connections etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . BSR 2022 20.19 |
| 187 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed ArrmouredAluminiumcable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withH4- Grade electrolyticaluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) includingtesting etc. as required of following size. OEM must have it\"s own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure \"A\" attached with this BSRBSR 2022 11.2 |
| 188 | 10.0 Sq. mmBSR 2022 11.2.3 |
| 189 | 4 coreBSR 2022 11.2.3.3 |
| 190 | 16.0 Sq. mmBSR 2022 11.2.4 |
| 191 | 4 coreBSR 2022 11.2.4.3 |
| 192 | 70.0 Sq. mmBSR 2022 11.2.8 |
| 193 | 3.5 coreBSR 2022 11.2.8.4 |
| 194 | P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24, Stiffness Class750 N,Externally corrugated and having smooth surface insidewith HDPE Coupler, Elbow, Teeat required Depth below the ground for laying cable of followingNominal Outer dia.MFR Test reportfrom NABL accrediated is to be submitted.(Excavation of Earth& Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .BSR 2022 12.12 |
| 195 | 50 mmBSR 2022 12.12.1 |
| 196 | 90 mm BSR 2022 12.12.4 |
| 197 | SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart andmade out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . For single phase Submersible / Monoblock pump 2.0 HP to 3.0 HP (DOL starter)BSR 2022 12.12 |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
