|
| 1 | Earth work excavation for foundation and depositing on bank with in the initial lead of 10m and a lift of 2m in hard stiff clay, stiff block cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc complete complying with SS20B. TNDSS No:23&24 |
| 2 | Cement concrete of mix 1:4:8 (one part of cement four part of sand and eight part of aggregates) using 40 mm gauge machine broken granite stone jelly for foundation including de watering if found necessary and laid in layers of not more than 15 cm thick well rammed and consolidated etc complying with standard specification. TNDSS No:28 |
| 3 | Supplying, fabricating and placing in position of Steel Reinforcement using Mild steel or ribbed tar steel rods, for all RCC works as per the design given by the departmental officers including cost of steel cutting, bending, placing in position and binding with binding wire and all labour charges for cutting, bending, tying and placing in position etc, complete. TNDSS No:97 |
| 4 | Reinforcement Cement concrete 1:1½:3 (one part of cement one and a half part of sand and three part of aggregates) using machine broken granite jelly of 20 mm size for all reinforced cement concrete works excluding cost of centering shuttering strutting and also cost of reinforcement grill in position but including laying vibrating with mechanical vibrators using finishing etc complete, as directed by the departmental officers etc complete complying with standard specification. TNDSS No:30 |
| 5 | Brickworkin cementmortar1:5 (one part of cement five part of sand) mix using country bricks of size 8¾\"x4¼\"x2¾\" includingcuring, cost and conveyance of all materials to siteand all labour charges etccompleteas per standard specification. |
| 6 | Supplying and erecting centering for sides and soffits including supports and strutting up to 3.29 m height for plain surfaces such as RCC slabs rectangular beams Tee or L beams lintels, stair case beam etc. in all floors with all cross bracing using mild steel sheets of size 90x60 cm and BG10 gauge stiffended with welded mild steel angles of size 25x25x3 mm for boarding laid over silver oak country wood joists of size 10x6.5 cm spaced at about 90 cm center to center and supported with casurina props of 10 cm to 13 cm Ø spaced at 75cm center to center etc. complete complying with standard specification in all floors. TNDSS No:30&36 |
| 7 | Supplying and erecting centering for sides and soffits including supports and strutting up to 3.29 m height for plain surfaces such as RCC slabs rectangular beams Tee or L beams lintels, stair case beam etc. in all floors with all cross bracing using mild steel sheets of size 90x60 cm and BG10 gauge stiffended with welded mild steel angles of size 25x25x3 mm for boarding laid over silver oak country wood joists of size 10x6.5 cm spaced at about 90 cm center to center and supported with casurina props of 10 cm to 13 cm Ø spaced at 75cm center to center etc. complete complying with standard specification in all floors. TNDSS No:30&36 |
| 8 | Supplying and fixing of steel door with suitable design including cost of materials, welding and conveyance of all materials to site locking arrangements and painting one coat of primer etc. complete as per standard specifications including fixing charges etc. complete for the work. |
| 9 | Supplying and fixing of steel window with suitable design including cost of materials, welding and conveyance of all materials to site locking arrangements and painting one coat of primer etc. complete as per standard specifications including fixing charges etc. complete for the work. |
| 10 | Paving floor with vitrified tiles (marbonite) in all floors over the base layer of cement mortar 1:3 (one par of cement three part of sand) 20 mm thick pointed with white cement at 0/40 kg/m2 including finishing the joints etc complete, as directed by the departmental officers (The rate should be exclusive of cost of flooring concrete 1:5) special. |
| 11 | Wiring with 2 x 1.5 Sq.mm (22/0.3) PVC insulated unsheathed single core copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A F.T. switch in flush with wall, covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light / fan point for electronic regulator. (Assume 5 Points Per Coil) (SD-22) |
| 12 | Wiring with 2 x 1.5 Sq.mm (22/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3 mm thick hylem sheet cover for 5 A 3 pin non interlocking FT wall socket and 5A FT switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. (SD-38) |
| 13 | Supply and fixing of 1400 mm (56inch) sweep AC ceiling fan complete with stepped electronic 300W regulator with 1metre down rod including fan clamp with side plates and cross arm of size 450 mm (18inch) SD 561 |
| 14 | Supply and run of 4 of 4 Sq.mm (56/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade on 7/20 GI bearer wire for service connection mains SD 67. |
| 15 | Supply and fixing in position best quality of approved make Wash hand basinof size 550 x 440 mm with all accessories such as cast iron brackets, including cost of 15 mm Ø brass nipple, 15 mm nylon connection etc including fixing the wash basin in the wall in position with a pair of CI brackets with TW plug and screws and giving necessary water supply connection and painting the brackets with two coats of paint over priming coat of anticorrosive paint including testing leakages etc, complete complying with standard specifications (the wash hand basin and the specials should be got approved by Departmental officer before use on works) |
| 16 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc complete complying with standard specification. (The make, quality and colour of paint should be got approved by the departmental officers before use on works.) |
| 17 | Dadooing the walls with plain glazed tiles of 150 x 150 x 6 mm set in cement mortar 1:2 (one part of cement two part of sand) 12 mm and pointing white cement used 4kg/m2 neatly etc complete as directed. |
| 18 | Ceiling plastering and finishing all RCC exposed surface such as RCC slabs, sunshade canopies, stair case steps, landing slab, etc. with cement mortar 1:3 (one part of cement three part of sand) 10 mm thick including packing the surface and provided necessary cement mortar nosing, headings as per the size specification wherever necessary using the same mix as directed by the departmental officers etc. complete complying with standard specification. |
| 19 | Plastering in cement mortar 1:4 mix (one part of cement and four part of sand) 12 mm thick finishing including cost and conveyance of all materials and labour charges for curing and all other incidental charges etc., complete complying with standard specification. |
| 20 | Weathering coarse cement concrete using best quality brick jelly of size 20 mm uniform gauge in pure slacked lime over RCC roof slab in the proportion of brick jelly to lime being 32:12 by volume and laid over on a single layer and consolidated to the required designed and finished thickness by beating the concrete with wooden beaters of approved pattern keeping the surface confirming welded by sprinkling lime jaggery water as per standard specification. |
| 21 | Finishing the top of roof with one course of machine pressed tiles of size 20 x 20 x 2 cm of approved quality laid in cement mortar 1:3 (one part of cement three part of sand) mixed with water proofing compound confirming to Indian standard as approved by the Departmental officers at 2% by weight of cement used and pointed with the same mortar mixed with the water proofing compound and red oxide complete complying with standard specification. |
| 22 | Painting the new walls two coats over one coat of priming with best cement paint of approved colour and quality including preparation of surface and finishing neatly etc., complete complying with standard specification and as directed by the department officers. |
| 23 | Supply and delivery of fixing of HDPE tank 1000 litres capacity as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of GI pipes and specials for pipe connection works including cutting, threading and fixing chargers as directed by officers. |
| 24 | Supplying, fabricating and fixing in position of alu. anodized natural colour matt finish fixed partition using 63.50 x 38.10 x 2 mm @ 1.174 Kg/m. Aluminium section at 900 mm C/C in vertical direction and 1300 mm C/C at horizontal direction with necessary rubber beadings. Aluminium Clips of size 17.27 x 17.15 x 1.40 mm @ 0.176 and using 5.50 mm plain glass at top and 12 mm thick both side pre laminated particle board at bottom including cost of all materials, labour and power consumption charges required for fabrication, drilling holes in RCC columns, beams masonry wherever necessary with power drill to the required extent and making good the dismantled portion to the original condition after fixing etc complete and as directed by the departmental officers. All the Alu section are to be anodized with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 for an average anodic film thickness of not less than 15 microns and all the materialsshould be got approved by the Executive Engineer before use on works. |
| 25 | Aluminium Door Single leaf size 2.10 m x 1.00 m Supplying fabricating and fixing in position of Alumi, Anoid natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.50 mm thick glazed door using rectangular AW Box section of following sizes for frame and shutter with necessary accessories such as rubber beading. A1 chips Best double action floor spring. Aluminium handles on both sides floor stopper, Tower bolt locks and glass including materials labour, power conception charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after foxing etc complete. The Alimi surface must be anodised with matt finish under electrically controlled condition in accordance with is specification 1868/1962 of Anodic thickness of not less than 15 microns (fifteen) for all sections. All the materials should be got approved by the Engineer incharge before fixing as directed. |
| 26 | Supply and delivery of submersible pump set having a duty condition of 100 lpm discharge against head of 125 metre confirming to IS specification with ISS marking suitable for installation panel board including cost of all materials and all conveyance charges etc complete as per standard specification. |
| 27 | Labour charges for the erection of submersible pump set in bore well / open well including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges up to the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pump set and trail run for 10 days. |
