|
| 1 | Demolition of cement concrete (unreinforced) in ground floor and pavingn.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed. |
| 2 | Demolition of brick workor stonework built in cement mortar including allquoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed. |
| 3 | Taking down cement plaster including backing etc from brick/stone walls / concrete surfaces including raking out joints,hacking for key , scrubbing down with water etc complete all as specified and directed |
| 4 | Dismantling plain or corrugatedsteel sheetsany gaugethickness including Nanital or similar pattern roof covering including ridges complete all as specified and directed. |
| 5 | Dismantlingtimber in scantling 40 sqcm and over in section, framed work complete all as specified and directed. |
| 6 | Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. |
| 7 | Taking downsteel water tubing 15 mm bore including all fitting and connections complete all as specified and directed. |
| 8 | Taking downsteel water tubing 20 mm bore including all fitting and connections complete all as specified and directed. |
| 9 | Taking downand removing chowkats with shutters (withouttaking off shutters from chowkat)not exceeding 1.50 Sqmeach complete all as specified and directed. |
| 10 | Taking down and removing chowkats with shutters (withouttaking off shutters from chowkat)exc 1.50 Sqmbut not exc 4.00 Sqm each complete all as specified and directed. . |
| 11 | Taking down Shutters of any description exc 1 sq. mand n exc 2 sq. m each and refixing in same opening after easing and adjusting, complete all as specified and directed. . |
| 12 | Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in hard/densesoil, complete all as specified and directed. |
| 13 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and directed. |
| 14 | Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed. |
| 15 | Brick work with old size fly ash bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:6 all as specified & directed. |
| 16 | Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 105 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkatscomplete all as specified. |
| 17 | Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 125 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkatscomplete all as specified. |
| 18 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete as shown on page No176 to 183 of MES SSR 2020 Part-II compete all as specified and directed.(Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) |
| 19 | Factory Made Solid PVC Moulded Door Shutter, with particleboard core,28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick MouldedPVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawinge,as shown on page No176 to 183 of MES SSR 2020 Part-II compete all as specified and directed. |
| 20 | 35mm thick2nd class hardwood Plain, framed,panelled shutters (any number of panels), withpanels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed. |
| 21 | 35 mm thick 2nd class hardwood glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members ofdoor shutters as specified in SSR- 2009Part-I Section 8.24(a) complete all as specified and directed. |
| 22 | Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x35mm double rebated comprisesgauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No\"s for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07. Make : As per Appendix \"C\". Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day. |
| 23 | Steel ventilator with top hung shutter including hinges, steel peg stay, complete, complete all as specified and directed. |
| 24 | Aluminium handles, cast type, anodised of size 125 mm complete all as specified and directed. |
| 25 | Aluminium anodizedbarrel tower bolt of extruded section of size 200 mm and fixed complete all as specified and directed. |
| 26 | Butt hinges, extruded aluminium alloy with galvanisedmild steel hinge pin, anodised and fixed, type B-21, 100mm size, complete all as specified and directed. |
| 27 | 250mm longaluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed. |
| 28 | 300mm, Mild steel, ordinary rat tail rod pattern springsincluding roller and roller plate completeall as specified and directed. |
| 29 | 100m size, Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 30 | Galvanished mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanished wire staples complete all as specified and directed. |
| 31 | Sheet glass, 3 mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed. |
| 32 | 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with screws to timber frame work, complete all as specified. |
| 33 | Continuous (piano) hinges,mild steel, bright finish or electrogalvanised, width of flap 30mm (when opened), complete all as specified. |
| 34 | 3mm thick, figured glasspin head type and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed. |
| 35 | Plain fillets of 2nd class soft wood, square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc 3 & not exc 6 sq.cm, complete all as specified & directed. |
| 36 | 2nd class soft wood (kail), clean sawn, timberframed and fixed as in scantling for ceiling complete all as specified and directed. |
| 37 | 4mm thick, Non asbestos fibre cement building boards fixed or laid/ inserted to framework with screws, as in ceiling , complete all as specified.Note : The board shall be as per IS-14862 and shall be manufactured from homogeneous mixture of cement, quartz and cellulose and shall be cured with high pressure steam using auto claving process. |
| 38 | 0.63 mm thick, galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with with L-type or J-type or cranked hook bolts ,in roofs, walls etc. with grade of zinc coating 275 gms per sqm complete all as specified and directed. |
| 39 | All as per item no 38above , but except sheeting complete all as specified and directed. |
| 40 | 0.80 mm thick, galvanised, plain mild steel sheetingas in ridges, hipe, valley gutters, drip and straight flashing (length and girth as fixed)with grade of zinc coating 275 gms per sqm complete all as specified and directed. |
| 41 | All as per item no 40above , but except sheeting complete all as specified and directed. |
| 42 | Mild steel work as in hold fast,wind ties for roof includingsecuring bolts including all necessary drilling ,bolting or reverting etc and all similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed. |
| 43 | 100mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) as in sub base of flooring/ hard standing complete all as specified and directed. . |
| 44 | 25mm thick PCC 1:2:4type B-0(using 12.50 mm graded crushed stone aggregates) as in sub base of flooring, finished even and roughto receive floor tiles all as specified and directed. . |
| 45 | Plain cement concrete 1:3:6, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75mmthick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved). |
| 46 | Chequered cement concrete colouredtiles, homogenious texture glossy finished, chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 20 mm thick cement screed in cement mortar 1:4 complete all as specified and directed. Shade/Colour of tile shall be approved by the AGE(I). |
| 47 | Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 48 | Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 49 | Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 50 | Machine cut kota stone slab flooring 20-25 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:4, cutting, rubbing, grinding and polishing to achieve mirror finish, laid over PCC subbase complete, all as specified. |
| 51 | Machine cut kota stone slab flooring 20-25 mm thick as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab,as inin skirting, dados, risers to steps etc, laid over and including 10mm thick rendering in cement mortar 1:4 , cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified. |
| 52 | Marble work (Udaipur Green) 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) usingmarble dust with admixture of pigment to match with marble shade. complete all as specified and directed. |
| 53 | Glazed ceramic colouredtilesof size350mm x 250 mm x7 mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 54 | Rendering cement plaster 10mm thick in cement mortar 1:6 on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing, surface finished even and smooth without using extra cement, all as specified. |
| 55 | Rendering cement plaster 10mm thick in cement mortar 1:3 on fair faces of brick wall or on concrete surfaces, as I ceiling, surface finished even and smooth without using extra cement, all as specified. |
| 56 | Rendering cement plaster 15mm thick in cement mortar 1:4 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified. |
| 57 | Rendering cement plaster 15mm thick in cement mortar 1:3in facia/edges/ceiling of chajjas and roof projections etc. including taking out peeled off plaster/ concrete and making the line in true shape , surface finished even and smooth without using extra cement, all as specified. |
| 58 | Preparation of wooden surfaces of any description, not otherwise described, over 10cm in width or girthand applying two coats of synthetic enamel paintover a coat of pinkprimer complete all as specified and directed. |
| 59 | Preparation of steel surfaces of any description, over10cm in width or girth,not otherwise describedand applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and directed. |
| 60 | Preparation of oldwooden surfaces of any description, not otherwise described, over 10cm in width or girthand applying one coat of synthetic enamel paint complete all as specified and directed. |
| 61 | Preparation ofnewplastered surfaces or un plastered, previously undecorated wall surfaces and applyingtwo coats of white wash, complete all as specified and directed. |
| 62 | Preparation ofnewplastered surfaces or un plastered, previously undecorated ceiling surfaces and applyingthree coats of white wash, complete all as specified and directed. |
| 63 | Preparation ofnewplastered surfaces or un plastered, previously undecorated ceiling surfaces and applyingtwo coats of white wash, complete all as specified and directed. |
| 64 | Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of 2 mm thick wall care putty complete, all as specified and as directed by Engr-in-Charge |
| 65 | Preparation of old plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of 2 mm thick wall care putty complete, all as specified and as directed by Engr-in-Charge |
| 66 | Preparation ofoldplastered surfaces or un plastered, previously undecorated wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 67 | Wash basins, Vitreous China (Flat white type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot\" or ‘Cold\" with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, completeall as specified. |
| 68 | Gun-metal, globe or gate valves, with iron wheelhead, screwed both ends for iron pipe and fixed 20mm bore iron pipe or for unions andcomplete, all as specified. |
| 69 | Gun-metal, globe or gate valves, with iron wheelhead, screwed both ends for iron pipe and fixed 15mm bore iron pipe or for unions andcomplete, all as specified. |
| 70 | Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repair, complete all as specified and directed. |
| 71 | Stop valves/ angle valve/ concealed valve, cast copper alloy, chromium plated, fancy type, screwed down,high pressure ,screwed both ends for 15mm bore iron pipe or for unionsfixed in repair complete all as specified. Note ; Type of valve approved by the AGE(I). |
| 72 | Brass CP mixer for mixing hot & cold water screweddown for iron pipe and fixed 15 mm bore, fixed in repair, complete all as specified and directed. |
| 73 | Brass chromium plated shower rose 125mm sizewith or without swivel joints, including fixing to steel pipeor union.fixed in repair complete all as specified. |
| 74 | Brass chromium plated tubular towel rail 20 mm dia, \"D\" type, 60 cms long between flanges with and including chromium plated brass brackets, brass screws complete all as specified |
| 75 | Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. |
| 76 | 600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers. |
| 77 | Soap dish, SS, approximate size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws, fixed in repair complete all as specified. |
| 78 | PVC connections 15 mm size with PTMT nutsof length 450mm fixed in repair complete all as specified and directed. |
| 79 | PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, fixed in repair, all as specified. Make: Cat Part No. 2602 ofCera or equivalent in makes mentioned in Appx . |
| 80 | Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc, fixed in repair all as specified. Make: Cat Part No. 2071 of \"Cera\" or equivalent makes mentioned in Appx. |
| 81 | Sink with drainage board made of stainless steel, l mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 82 | 20 mm dia, ball valves high pressure of PTMT with epoxy coated Aluminiumrod& highdensity plastic ball screwed for iron pipe and fixed in repair complete all as specified and directed.(Minimum weight 210gms), |
| 83 | G I tubingmedium gradeof 15 mm borewith all fittings and fixtures fixed to wall and ceiling or laid infloor/trenches complete all as specified and directed. |
| 84 | All as per item no 83, above but exept pipe |
| 85 | G I tubingmedium gradeof 20 mm borewith all fittings and fixtures fixed to wall and ceiling or laid infloor/trenches complete all as specified and directed. |
| 86 | Cutting chases, in brick walls ,pinning in. makinggood to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified. |
| 87 | 75mm dia PVC(SWR)pipe single socketed with rubber ringjoints, laid/fixed to trenches or in floor or walls complete all as specified and directed. |
| 88 | 110mm dia PVC(SWR)pipe single socketed with rubber ringjoints, laid/fixed to trenches or in floor or walls complete all as specified and directed. |
| 89 | 75 mm dia PVC(SWR) bend, any radius complete all as specified and directed. |
| 90 | 75 mm dia PVC(SWR) bend, any radius provided with access door complete all as specified and directed. |
| 91 | 110mm dia PVC(SWR) bend, any radius provided with access door complete all as specified and directed. |
| 92 | 110mm dia PVC(SWR) junction single, (Single T) equal or unequal , complete all as specified and directed. |
| 93 | 75mm dia PVC(SWR) junction single, (Single T) equal or unequal , complete all as specified and directed. |
| 94 | PVC (SWR) vent cowl, 75mm dia , complete all as specified. |
| 95 | PVC (SWR) floor trap, plain with grating including jointing with solvent cement for 75mm bore pipe, complete all as specified. |
| 96 | Rotational moulded polyethylene water storage tank 500 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified. |
| 97 | 25mm dia curtain rod, colour coated with wooden bracket and wooden funnel over door and window fixed with steel screw and PVC cleat, complete all as specified and directed. |
| 98 | Surface Preperation (Bathroom portion):Cleaning the surface and made free of dirt, foreign particles, laitance followed by grinding all protrusions to make surface modulated. Thereafter, inspection for cracks on the surface caused by thermal expansion contraction. Cutting the grooves with suitable cutter machine in \"v\" groove filled with Repair mortar/Microconcrete/General purpose grout as recommended proportionaly as per recommendation of manufacturer.Making of Gollas at all the corners with Polymer modified mortar(1:4 Cement:sand with 3.5% Acylic of cement by weight and applyingtwo component elastomeric acrylic polymer modified cementitious waterproofing coating, SmartCare Damp Block 2K or approved equivalent , having 100 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The coating shall have food grade certificate from laboratories like CFTRI. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc, complete as per manufacturers specifications.Make- Asian Paints or equivalent as approved by AGE(I). |
| 99 | Layingslope making and protection to the waterproofing treatment with 30 mm avg thick M20 grade screed for floors. Providing and applying 15 mm thick with CM 1:4for wallplasteringadmixed with PC based integral waterproofing compound SmartCare Vitalia, etc. complete, as per manufacturer\"s specifications.Make- Asian Paints or equivalent as approved by AGE(I). |
| 100 | Filling the sunk portion with cinder/brick bat coba (in slope) and providing finish as per consultant\"s methodology and specification. Note:- Slope to be maintained with PCC/CM which is to done over the brick bat/cinder filling and rate shallhavedeemed in the quotedrate. |
| 101 | Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing fan regulator any type (Where required) and electric meters are to be refixed and connected properly where required. |
| 102 | Point wiring with copper conductor cable multistrand, PVC sheathed 1.5 Sqmm size(two run with colour code RYB) for one light point ,fan point, exhaust fan point,or bell point controlled by one switch including one run of 1.5 Sqmm (as continous earth wire Green)multistrand PVC concealed conduit of approved size and quality ISI marked,including all other required accessories as specified in preamable 1(a) to (q) of section 19 of SSR Part-II under heading \"point wiring\" fixedon wall/ceiling including sunk cast iron terminal boxes grouting/flushing on wall for mounting fittings like switch,sockets etc covered with 3.00 mm thick plastic laminated sheet top cover of brick masonary/Stone masonary wall complete including cutting,chasing,pinning and making good the disturbed surface by using cement mortar 1:3 complete all as specified and directed by Engr-in-charge.,(Note:-the rate for concealed type point wiring shall deemed to include the cost of cutting,chasing in wall by using electric cutter andmaking good the disturbed surface of wall by providing cement plasterand matching the surface by white wash/colour wash all as per existing finishes complete). |
| 103 | All as per serial item No \"102\" above, but for one 3 pin 5 Ampssocket outlet on the same board all as specified and directed. |
| 104 | All as per serial item No \"102\" above, but for one 3 pin 5 Ampssocket outlet, independent all as specified and directed. |
| 105 | All as per serial item No. \"102\" above but for 3 pin 15 Amps socket out letindependentwith 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified. |
| 106 | Switch piano flush type, single pole, one way, 5 Amps, all as specified. |
| 107 | Switch piano flush type, single pole, one way, 16 Amps, all as specified. |
| 108 | Bell push, flush type, 5 amp all as specified. |
| 109 | Socket outlet, 3pin, , 6 amps flush type, all as specified. |
| 110 | Socket outlet two in one, 3 Pin 5 amps and 15 amps, flush type, all as specified. |
| 111 | Bell, AC, 230 volts, single pole all as specified. |
| 112 | Lamp holder, PVC/Polycarbonate type with back plate suitable for angular/ batten fittings including LED lamp, 10 watts complete all as specified & directed. |
| 113 | Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified. |
| 114 | Renewal of sub main wiring with two single core PVC insulated cable1100 volts grade with copper strandedRLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire ofsize 4 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor andone RM of earth wire of 4 Sqmm,shall be measured as one RM). |
| 115 | 15Watt, 5700K,Energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 protection and Impact resistance of IK07, connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of suitable size, complete all as specifiedMake: Havells cat part No. LHEWEBP7PL6S015 or equivalent in Appx |
| 116 | MCB SPN 32-63 Amp, 240 Volts, 10 KA all as specified. |
| 117 | MCB SP 6 to 32 Amp, 240 Volts, 10 KA all as specified. |
| 118 | MCB TPN 63 Amps (01 incoming& 06 outgoing), 415 Volts, 10 KA all as specified. |
| 119 | Sheet metal enclosures for DBs when MCBs to be used, triple pole and neutral, 4 way, double door, 415 volts with 200 Amp rated bus bar including taking down ICDP/ DB\"s any type, kit kat fuse, MCB\"s any type, all as specified. |
| 120 | Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 12 way, double door, 240 volts with 200 Amp rated bus bar completed all as specified. |
| 121 | Taking down, keping in safe custodyand re-fixing/connecting existing electric meters single phase complete all as sepcified and as directed |
| 122 | Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmentalfriendly, energy efficient ready to use pack. 1x18W, LED 6500 K, 230V, connector block etc completewith all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable sizeincluding dismantling of unserviceable tube light all as specified and directed. Make: Havells cat part No. LHEXACP7UN1W018 or equivalent in Appx |
| 123 | Wall mounted LED integrating batten fitting T5, 10 Watt LED, 2 feet, PVC extruded with 10 watt LED tube rod with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete.Make: Havell\"s Cat Part No. LUMILINEBS10WLED865SPCWH of\"Havells\" or equivalent in makes mentioned in Appendix |
| 124 | Taking down and refixing exhaust fanand connecting up including provision of cable ceiling rose/connector to fan, complete all as specified. |
| 125 | Exhaust fan, 300mm sweep, steel body AC single Phase. 230V complete with with, blades, and frame and louversincluding provision of cable copper flexible PVC three core 23/0.0076 from ceiling rose to fan, complete all as specified . Note : Quoted rate shall include for making hole in wall for grouting, fixing the fan on outer side of wall with suitable size anchor bolt and making good disturbed surfaces without ant extra cost. |
| 126 | Taking down andre-fixing electric water heater, storage typeany type25 litre,all as specified and directed. |
| 127 | Sheet metal enclosure, factory madedust and vermin proof made out of 2.00mm thick MS sheet of size 75x60x30 cm depth with doubledoor hinged shutter and locking arrangementfor fixing only suitable arrangement for TPN 4 way DBs -01 no andKWH meter-02 Nos with PVC transparent sheet suitable for visblity of meter reading with complete connection of meter and DB Outlet MCBs with 4 Sqmm single core PVC wire complete wiring should be fixed /covered proper tie and PVC casing coverflushed/semi flushed /grouting on wall surfacecomplete all as directed (Note: (i) Unit rate shall be inclusive of making good the area not exceeding 0.6 sqm and not exceeding 0.125m depth for filling the hollow existing surface with half bricks in CM (1:4) all as specified and directed by Engr-in-charge.(ii) The sheet metal enclosure shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer internally and externally with machine spray. |
| 128 | Cutting/ grooving on plinth/ wall/ verandah in any condition for laying of cable through pipe and making good the disturbed surface by using cement concrete 1:2:4 type B-0, using 12.50graded crushed stone aggregate as required complete all as directed. |
| 129 | Sand cushioning to under ground cables provided with a layer of sand 8 cms thick before laying the cable and 15 cms thick after laying the cable complete all as specified and directed. |
| 130 | Sub class \"B\" bricks for covering to cable laid dry flat, with width equal to length of bricks all as specified and directed. |
| 131 | GI pipe light grade of size 40 mm dia laid in trenches/ walls including clamps, screws etc, complete all as specified and directed. |
| 132 | XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 25 Sqmm, 3.5 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed. |
| 133 | Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC (1:2:4), type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC (1:2:4), type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixingarrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electricalplate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. |
| 134 | Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 30 of tender doucments. |
