|
| 1 | Providing and applying 10 mm thick Cement plaster in Cement mortar 1:3 ( One part of Cement and Three parts of Sand ), to finishing the exposed surfaces of R.C.C. items of works such as Roof (or) floor slabs, beams, and Sun shades etc.to correct plane and level including scaffolding, hacking of surface, chiselling the undulated surface wherever necessary and curing etc., all materials and labour complete in all respects including all lead, lift and descent and as directed by the Enineer in charge. This rate includes the cost of providing Cement Mortar beadings for sun shades, steps,landing slabs, elevation etc. complete complying with standard specifications. |
| 2 | Providing & applying 12 mm thick cement plaster in CM 1:5 (1 part of cement: 5 parts of sand) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or chambering of corners, offsets, fin/ bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface,chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent andas directed. |
| 3 | Plastering in cm 1:5-20mm thick including cost and conveyance and all other labour charges |
| 4 | Flooring & Dadooing Paving the floor with best approved quality Anti skid tiles of 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification |
| 5 | Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining,curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panellingwherever necessary and as directed by the departmental officers). |
| 6 | Supplying and fixing in position steel balustrades using 20mm square rods spaced at 150mm centre to centre so that the two balustrades in each step shall be placed centrally and the top of balustrades connected with the hand rails (cost of hand rail shall be measured and paid separately) by means of MS flats of size 40mm x 6mm in the groove 40mm x 6mm provided at the bottom of hand rail; the bottom of balustrades shall be fixed on to the top of step concrete.An additional MS flat of size 50mm x 6mm shall be provided at the centre of balustrades connecting all square rods to the entire length including cost of square rods, flat and applying one coat of red oxide primer to the iron surfaces, etc., complete complying with standard specification and as directed by the departmental officers. |
| 7 | Supplying and fixing 40mm dia GI pipe for staircase hand rail including labour charges for cutting, welding and fixing with MS flats (excluding cost of flat), etc., as directed by the departmental officers |
| 8 | An MS square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge between them. All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers.All sections should be in confirmed with IS 7452/1990.The cost includes cost of all materials, labour charges and other incidental charges, etc., complete |
| 9 | Manufacturing, supplying and fixing of Steel doors with following specification.MS angle of size 40x40x6mm at 3.5 kg/m used for outer frame and MS Angle of size 35x35x5mm at 2.6 Kg/m for the shutter frame.Stiffeners with 32x6mm at 1.5 Kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18 G CR Sheets of best quality is laid as panel in theshutter frames.18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50kg/m MS Flat on the rear side of the door, sandwiching the CR Sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter. 300mm length ofhinges 2Nos, for shutter is provided.6 Nos. of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door.Tower bolt 2 Nos. at the top provided. |
| 10 | Supplying and Painting new plastered surface with two coats of distempering one coat of distemper primer |
| 11 | Providing and applying Emulsion paint finish ofapproved make & shade in twocoats over a coat of approved primer and 2 coats of pattyto give an even shade as per manufacturer\"s instruction to the internal plastered surfaces including preparation of surfaces, scaffolding etc. all complete as per drawings andspecification for all heights. |
| 12 | Weathering Course Concrete using best quality broken brick jelly of 20 mm uniform gauge in pure slaked lime ( NO Sand to be used ( over the RCC roof slab in the proportion of brick jelly to lime being 32 : 121/2 by volume laid over in single layer and consolidated to the required slope and finished thickness and beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime, jiggery water etc. complete complying with standard specifications and as directed |
| 13 | Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers. |
| 14 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 15 | Supplying and fixing cuddapah slab for cupboard shelf |
| 16 | Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be gotapproved from the Executive Engineer befoe use on wor |
| 17 | Light point Wiringwith 2x1.5 Sq.mm (22/0.3) PVC insulated SC unsheathed Cu. conductor of 1100v grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with T.W. swithc box and 5A F.T. switch with painting of suitable colour for ope |
| 18 | Fan point Wiringwith 2x1.5 Sq.mm (22/0.3) PVC insulated SC unsheathed Cu. conductor of 1100v grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with T.W. swithc box and 5A F.T. switch with painting of suitable colour for open |
| 19 | Supply and fixing of 5A 3 pin and 2 pin combined flush type wall socket with 5 A flush type switch concealed in suitable M.S box in flush with wall SD 130 |
| 20 | Supply and fixing of 6 way SPDB of 16A / with 16ADPIC switch of 500V (side handle) with F&N on suitable T.W. board with PWD earthling SD 143 |
| 21 | Supply and fixing of single box type 4’ 40w flu. fittings complete with copper choke and condenser with TW round blocks on wall (or) ceiling with flu. tube with PVC unsheathed copper lead from terminals to the fittings. SD 83 |
| 22 | Supply and fixing of 1200mm (48”) AC ceiling fan complete with dimmer type electronic 300w regulator with 1m down rod on the existing clamp SD 103 |
| 23 | Supply and run of 2 of 4 Sq.mm (56/0.3) PVC insulated SC unsheathed Cu. conductor of 1100 V on 7/20 GI bearer wire for service connection mains SD 63. |
| 24 | Supply and delivery of PVC pipes & specials for Rain water harvesting structure 110mm PVC Pipe |
| 25 | 110mm PVC Tee |
| 26 | 110mm PVC Elbow |
| 27 | GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column \"BB\" for all works in this package} |
