Tender For Installation Of Open GYM (Cen Iy1), CHILLDREN Play Equipments And Sitting Benches In Parks Under Hubli-Dharwad Municipal Corporation. CrossWalker Providing, Supplying, fixing, installation, commissioning and trial run of Cross Walker. Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5 % NaCl solution in accordance to ISO 7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 2015 x615x1360mm (min) Weight: 93 KG (min) Safety Area: 5015x3015mm (min),Capacity 2 persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site. condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge 2 LegPress Providing, Supplying, fixing, installation, commissioning and trial run of Leg Press. Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns. All metal Parts are to be testedin salt spraymachine that uses a 5% NaCI solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre-assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 2270 x635x1640mm (min) Weight: 60.20KG (min) Safety Area: 5300x3685mm (min),Capacity 2 persons. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Leg & Thigh Excercise/Air Walker Providing, Supplying. fixing. installation, commissioning and trial run of Air Walker. Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns. Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5% NaCl solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings Scope of delivery:1 Completely pre- assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly Size LxWxH: 1065 display the GS mark as issued in the EN 16630 safety certificates. x615x1364mm (min) Weight: 51KG (min) Safety Area: 4090x3555mm (min),Capacity 1 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all of respects for its intended use. The works required in fixing the eqiupment on site as per the site. condition. The cost includes, cost transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge AB Trainer/sit-up Bench Providing. Supplying. fixing. installation, commissioning and trial run of Air Walker Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5% NaCl solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre- assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide, Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 1412 x1366x650mm (min) Weight: 42.60KG (min) Safety Area: 4462x4078mm (min),Capacity 2 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Push And Pull Up Chair Providing. Supplying. fixing. installation, commissioning and trial run of Pull Up Chair Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5% NaCl solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre- assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only.The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 2570 x805x2685mm (min) Weight: 85.40KG (min) Safety Area: 6287x4848mm (min), Capacity 2 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Seated Chest Press Providing, Supplying. fixing, installation, commissioning and trial run of Seated chest Press. Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process.All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5%NaCl solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre- assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide, Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 1955 x733x2058mm (min) Weight: 86.60KG (min) Safety Area: 5545x4470mm (min),Capacity 2 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge This Wheel Spend Supplying, fixing, installation, Providing. commissioning and trial run of Thi chi Wheel Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5% NaCl solution in accordance to ISO7227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre- assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark. The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 1120 x1150x1620mm (min) Weight: 39.00KG (min) Safety Area: 3520x3550mm (min),Capacity 3 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Twister Triple Waist Providing, Supplying. fixing, installation, commissioning and trial run of Waist Twister. Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded. All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5% NaCl solution in accordance to IS07227 to handle corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre- assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide,Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 safety certificates. Size LxWxH: 1460 x1310x1150mm (min) Weight: 39.10KG (min) Safety Area: 4360x4510mm (min), Capacity 3 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Single There isnt Setup Cycle Providing, Supplying. fixing, installation, commissioning and trial run of Single pole set up Cycle Metal:All tubular steel of 2.5mm thickness are galvanized and zinc dipped,joints are robotic welded.All welded joints are scalloped as necessary and welded to an approved MIG process. All welds are dressed off removing all sharpedges and burns.Zinc primer paint is applied at all the welded points prior to finishing. All metal parts are powder coated using AKZO nobel-Great wall powder to the thickness of 80-120 microns.All metal Parts are to be testedin salt spraymachine that uses a 5% NaCl solution in accordance to ISO7227 to handle. corrosion for 3000Hrs. Rubber:High quality grip rubber is used for the handles. Bearings Maintenance free ball bearings.Scope of delivery:1 Completely pre- assembled equipment model, Maintenance: Maintain according to EN 16630 and as per maintenance guide, Safety: All products must be tested and certified to meet EN 16630 safety standards with GS test mark.The EN 16630 certificates must be issued by a reputed notified international certifying agency such as IPEMA, TUV, CPSC or SGS only. The GS mark EN 16630 Certificates must be in the name of tendering party and not any 3rd Party. All products must clearly display the GS mark as issued in the EN 16630 x498x1290mm (min) Weight: 51.50KG (min) Safety Area: 3400x3498mm (min),Capacity 1 persons The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of safety certificates. Size LxWxH: 1000 transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge. Providing, Supplying. fixing. installation, commissioning and trial run of Rainbow Climber. LK-CL-81,All Round and rectangular pipes are GI Or CRISI make Guage 14 guage, 2coating are red oxide and final paints of industrial paint, Nut bolt GI Bearing heavy.(Branded.) FRP thickness 4- 5mm,Swing assembly 6mm chain with rubber. coating Length-12Ft, Width-2Ft,Hiegth-5 Ft, The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Providing. Supplying, fixing, installation, commissioning and trial run of Sea saw Double- LK-SS-63,All Round and rectangular pipes are GI Or CRISI make Guage 14 guage,2coating are red oxide and final paints of industrial paint, Nut bolt GI,Bearing heavy.(Branded.)FRP thickness. 4- 5mm,Swing assembly 6mm chain with rubber coating Length-8Ft,Width-5Ft, Hiegth-2 Ft., The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Providing, Supplying, fixing, installation, Us commissioning and trial run of Arch swing two seaters-LK-SW-51,All Round and rectangular pipes are GI Or CR,ISI,make Guage 14 guage, 2coating are red oxide and final paints of industrial paint, Nut bolt GI Bearing heavy,(Branded.) FRP thickness 4-5mm,Swing assembly 6mm chain with rubber coating Length-10Ft.Width-5Ft. Hiegth-9 Ft, The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge 4 Providing, Supplying. fixing, installation, commissioning and trial run of Two way Slide,All Round and rectangular pipes are GI Or CRISI ,make Guage 14 guage,2coating are red oxide and final paints of industrial paint,Nut bolt GI Bearing heavy,(Branded.)FRP thickness 4-5mm,Swing assembly 6mm chain with rubber coating Length- 15Ft, Width-20Ft, Hiegth-9 Ft, The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge installation, Providing, Supplying, fixing, commissioning and trial run of Standing Marry Go round. All Round and rectangular pipes are GI Or CR,ISI make Guage 14 guage, 2coating are red oxide and final paints of industrial paint, Nut bolt GI Bearing heavy,(Branded.) FRP thickness 4- 5mm,Swing assembly 6mm chain with rubber coating Diameter-4Ft,Heigth-4Ft, The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Providing. Supplying, fixing, installation, commissioning and trial run of Duck Marry Go round, All Round and rectangular pipes are GI Or CRISI make Guage 14 guage, 2coating are red oxide and final paints of industrial paint, Nut bolt GI Bearing heavy, (Branded.) FRP thickness 4- 5mm,Swing assembly 6mm chain with rubber coating Diameter-5Ft,Heigth-4Ft. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The work includes all Ne other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Providing, Supplying and Fixing, Installation, Commissioning and Trail run of children Play Equipment Monkey Bar VFM Support posts of height 1.82m are to be schedule Galvanized. steel with a 60 mm OD (Outer Diameter) All the posts are to be finished with a baked on powder coat finish. Handrail of size 1.3 m and Dia 48 mm shall be an welded unit, fabricated from 48 OD galvanized steel pipes with a baked on powder coating finish. Bolts, nuts,screws, washers and et used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Electrostatically applied polyester powder must have a tough finish with maximum durability. The costs includes, Cost of the transportation, Cost of Labour, HOM of machinery etc., required to complete the work as per the direction of Engineer-in-Charge. Providing. Supplying and Fixing. Installation, Commissioning and Trail run of childern Play. Equipment Creppy Crawly climber: The wavey support bars are of height 1.5 m are to bet schedule HOT DIP Galvanized steel with a 48 mm OD Powder coatings used is Akzo Nobels The finished products have the following typical characteristics: 0.5mm thickness, oven cured between 191cC and 2200C, to achieve Flexibility, Impact, Salt Spray (Corrosion) Resistance, Hardness, and Adhesion. All post. caps are to be cast from aluminum which is pretreated, cured and sandblasted, 114mm. diameter, with a baked or powder coat finish Handrail of height Dia 32 mm shall be an all- robotic welded unit, fabricated from 32 OD. galvanized steel pipes with a baked on powder coating, finish. The Electro-statically applied polyester powder has a tough finish with maximum durability using AkzoNobel INTERPON paints application, and dual zone cure oven to a thickness of 0.5mm thickness, oven cured between 1910C and 2200C Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as per EN1176 standards as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well The costs includes, Cost of the transportation, Cost of Labour, HOM of machinery etc., required to complete the work as per the direction of Engineer-in-Charge. Providing, Supplying and Fixing, Installation, Commissioning and Trail run of childern Play Equipment Puppy dog Rider Elephant rider / Horse rider:: HDPE of size 0.83 mx 0.31 mx 0.87 m, Plastic Components [super thick plastic) shall be rotationally molded from antistatic. copolymer, virgin linear low density UV stabilized polyethylene, with colormolded in not added in. All rotational molding is carried out in state of the art, precision, bi axial roto moulding machines which helps achieve guaranteed uniform wall thickness, seamless joints, accurate process control, one part construction to make it stress free. Specialized connectors such as clamps and couplings are to be cast from aluminium which is pre- treated, and cured, with a baked on powder coat finish. The costs includes, Cost of the transportation, Cost of Labour, HOM of machinery etc., required to complete the work as per the direction of Engineer-in-Charge. Supply and fixing of children Play Equipment Fireo N Swing: Shaped structural posts of height 2.31m are to be schedule HOT DIP Galvanised steel with a 114mm OD and 2.2mm (Wall)thickness of the tubing. Toprail at height 2.31m and dia 114mm Shall be an all-robotic welded unit, fabricated from 114 O.D.Plastic Components such as swing seats(superthick plastic shall be animated and shall be rotationally molded from antistatic, copolymer, virgin linear low density UV stabilized polyethylene, with color molded in and minimum thickness of 6-8mm. The costs includes, Cost of the transportation, Cost of Labour, HOM of machinery etc., required to complete the work as per the direction of Engineer-in-Charge. Supply and fixing of children Play Equipment Maxima N Swing: Inverted U Shaped structural posts of height 2.31m are to be schedule HOT DIP Galvanised steel with a 114mm OD and 2.2mm (Wall)thickness of the tubing. Toprail at height 2.31m and dia 114mm Shall be an all- robotic welded unit, fabricated from 114 O.D.Plastic Components such as swing seats(superthick plastic )shall be animated and shall be rotationally molded from antistatic, copolymer, virgin linear low density UV stabilized polyethylene, with color molded in and minimum thickness of 6-8mm. The costs includes, Cost of the transportation, Cost of Labour, HOM of machinery etc., required to complete the work as per the direction of Engineer-in-Charge. SITTING BENCHES Providing and laying Surface Mount Reinforcement Bench Conforming to RDSO spect, without Arm rest and Back support with material specification of RCC M-30 Grade con le mix in accordance with 15: 10269/Latest in gray cement by using vibro-compaction technique and with reinforcement as detailed in Govng, speen. TMT reinforcement bars conforming to IS: 1786/1 of dia 10 mm used as main reinforcement bar and 4 mm dia mild steel bars used as stirrups as per drawing, Stirrups of 10 nos.-4 mm dia bar @ 150 mm C/C and Main Reinforcement 4 nos.-10 mm din bar. Each seating plank (bottom) of bench bolted with leg by help of 12 mm dia. X 65 mm length galvanized steel countersunk bolts with EVA washer Backrest planks fitted with half threaded carriage bolts and nuts of size 165 mm X 8 mm dia with EVA & steel washer. Plank Dimension- 1500mm x 440mm, Seat height from the ground 450mm, Distance between both legs. 340mm Architect drawing and direction. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge Providing and fixing seating bench ino base slab, 1no back rest, 2no legs, made up of granite stone with nice finish chamfered edge and fillet corner finishes is conveyed to work site it is inclusive of all lead and lift, labour, transportation loading unloading charges, over heads, hire charges of machinery all and placing in position etc... complete work shall be carried out as per the detailed specification, Architect drawing and direction of the engineer in charge of the work. The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the eqiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge
