Public Works Department-PWD has published Proposed Construction Of Community Hall At Madhya Bhubanban Under 4 Barjala- Assembly Constituency, West Tripura / Sh: Building Portion Including Internal Water Supply, Sanitary Installation, Sewage, Drainage Works, Boundary Wall And Internal Electrificat. Submission Date for this Tender is 22-08-2023. Building Work Tenders in agartala Tripura. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | SUB-HEAD : EARTH WORK |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. - All kinds of soil |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. - All kinds of soil |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. - All kinds of soil |
| 5 | Extra for additional lift of 1.5m or part thereof. - All kinds of soil |
| 6 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 7 | Supplying chemical emulsion in sealed containers including delivery as specified. |
| 8 | (i) Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 9 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment as per IS: 6313 (Part III)- Latest revision (excluding the cost of chemical emulsion): |
| 10 | (i) Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. - With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 11 | (ii) Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling: - With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 12 | SUB-HEAD : CEMENT CONCRETE WORK |
| 13 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level: |
| 14 | (i) 1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size) |
| 15 | (ii) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) |
| 16 | (iii) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 17 | Centering shuttering including struttings, propping etc. and removal of form work for: |
| 18 | (i) Foundations, footings, bases for columns. |
| 19 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer"s specification |
| 20 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 21 | SUB-HEAD : RCC WORK |
| 22 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- -All work upto plinth level: |
| 23 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 24 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement- |
| 25 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 26 | (ii) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 27 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies,shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement- |
| 28 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 29 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size). |
| 30 | Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with |
| 31 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 32 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete uptoplinth level. |
| 33 | (i) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 34 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 35 | (i) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 36 | Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits |
| 37 | (i) 50 mm thick |
| 38 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in vertical & horizontal fins, individually or forming box louvers, setting in cement mortar 1:2 (1 cement : 2 coarse sand), including the cost of required centering, shuttering but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size). |
| 39 | Centering shuttering including struttings, propping etc. and removal of form work for: |
| 40 | (i) Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 41 | (ii) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply |
| 42 | (iii) Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply |
| 43 | (iv) Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply |
| 44 | (v) Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 45 | (vi) Stairs (excluding landings) except spiral-staircases with wooden plank |
| 46 | (vii) Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards. |
| 47 | (viii) Edges of slabs and breaks in floors and walls under 20 cm. wide |
| 48 | (ix) Weather shade, Chajjas, corbels etc., including edges. |
| 49 | Providing and fixing sheet covering over expansion joints with iron screws as per design to match the colour /shade of wall treatment. (i) Non-asbestos fibre cement board 6 mm thick as per IS: 14862 [150mm wide] |
| 50 | SUB-HEAD : BRICK WORK |
| 51 | First class brick work in foundation and plinth including cost of all materials as required complete. |
| 52 | (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 53 | (ii) In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 54 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete. |
| 55 | (i) In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 56 | Half brick masonry with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- |
| 57 | (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 58 | Extra for providing & placing in position 2 nos 6mm dia MS bars at every 4th course of half brick masonry work including anchorage in joints of 75mm in each side in superstructure for all level including cost of all materials as required complete:- |
| 59 | (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 60 | SUB-HEAD : CLADDING WORK |
| 61 | Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc.complete at all levels:- |
| 62 | (i) 18 mm thick Rajnagar Plain white marble/ Udaipur green marble/ Zebra black marble or equivalent duly approved:- - Area of slab upto 0.50 sqm. |
| 63 | (ii) 18 mm thick Granite of any colour and shade duly approved. - Area of slab upto 0.50 sqm. |
| 64 | Providing edge moulding to approved thickness marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete at all levels as required as per design approved by the Engineer-in-charge:- |
| 65 | (i) 18 mm thick Granite work. |
| 66 | Providing and fixing stone slab with table rubbed, edges rounded and polished of size 75x50 cm deep and approved thickness fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth including rubbing, curing etc. complete at all levels as required (measurement should be of exposed finished work):- |
| 67 | (i) White Agaria Marble Stone of approved shade of 18 mm thick (75 x 50 cm). |
| 68 | SUB-HEAD : WOOD WORK |
| 69 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : |
| 70 | (i) Local Teak wood |
| 71 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters. |
| 72 | (i) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 73 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. |
| 74 | (i) Fixed to openings /wooden frames with rawl plugs screws etc. |
| 75 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 76 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 77 | (i) 300 x 16 mm |
| 78 | (ii) 250 x 16 mm |
| 79 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 80 | (i) 300 x 10 mm |
| 81 | (ii) 250 x 10 mm |
| 82 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 83 | (i) 125 mm |
| 84 | (ii) 100 mm |
| 85 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. |
| 86 | (i) Single rubber stopper |
| 87 | Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws. |
| 88 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in- charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter). |
| 89 | Providing 50 × 50 × 50 mm Gamair wood plugs including cutting brick work and fixing in cement mortar 1:3 (1 cement: 3 fine sand) and making good the walls etc. |
| 90 | Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. |
| 91 | Providing and Fixing Channeled Hi Density Fiber Board Wall Panel (woodworks) (WC01C28LUMW) perforated panels of width 128mm, thickness of 15mm and length 2440mm with minimum 830 kg/M3 density substrate with a laminated facing as per the approved shade/species & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 4mm width and 28 mm visible panel each. The panels shall provide a fire reaction of Class of 1 as per Part 7 of BS 476. The edges of the panels shall be “tongue-and- grooved” to receive special clips for installation. |
| 92 | The back of the perforated panel shall have sound absorbing non- woven acoustical fleece having NRC of 0.55. The panels shall be mounted on special aluminium splines using clips. Install wooden battens of section 50 mm x 50 mm or approved by the Architect on the solid wall horizontally using screws and plugs at spacing of 600 mm centre-to- centre. Screw the aluminium-extruded keel for channeled wood works (GTPT001) over the lowest and second wooden batten at an on-centre distance of 600 mm. Install the first set of wooden panels by inserting the clips for border channeled woodworks (GTPT002) and insert the grove of the panel into the projecting flange of the aluminium clip. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing clips for inside channeled woodworks (GTPT003) into the next keel till the actual height is achieved. Use clips for borer channeled woodworks (GTPT002) to finish off the installation. Finish off the edges using wooden moulding of matching colour |
| 93 | Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of |
| 94 | size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer"s specification as per direction of Engineer-in-Charge all complete. |
| 95 | SUB-HEAD : STEEL WORK |
| 96 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required. |
| 97 | Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 98 | Providing and fixingfan clamp type-Iof 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete. |
| 99 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:- |
| 100 | (i) In grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 101 | Providing and fixing M.S. round holding down bolts with nuts and wahser plates complete as per standard design. |
| 102 | Providing and fixing MS bolts including nuts and washers complete as per standard design:- |
| 103 | (i) Upto 300mm length. |
| 104 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 105 | SUB-HEAD : ALUMINIUM WORK |
| 106 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :- |
| 107 | (i) For fixed portion of approved quality:- - Anodisedaluminium(anodisedtransparentordyedto requiredshadeaccordingtoIS:1868,Minimumanodic coating of grade AC 15). |
| 108 | (ii) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- - Anodisedaluminium(anodisedtransparentordyedto requiredshadeaccordingtoIS:1868,Minimumanodic coating of grade AC 15). |
| 109 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- |
| 110 | (i) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 111 | (ii) With float glass panes of 5.5 mm thickness ( weight not less than 13.50 kg / sqm ) |
| 112 | Providing and fixing stainless steel (SS 304 grade) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-in-charge:- |
| 113 | (i) 255 x 19 mm |
| 114 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality completeas per direction of Engineer-in-charge:- |
| 115 | (i) Anodised aluminium of grade AC 15. |
| 116 | Providing and fixing 100 mm brass locks ( best make of approved quality ) with 6 levers without pair of handles for aluminium doors including necessary cutting and making good etc. completeas per direction of Engineer-in-charge. |
| 117 | SUB-HEAD : FLOORING AND SKIRTING WORK |
| 118 | Providing and laying cement concrete 1:2:4 (1 cement: 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips etc. complete. |
| 119 | (i) 40 mm thick |
| 120 | Providing and fixing Marble stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishingcomplete. |
| 121 | (i) 18mm thick Marble Stone - Raj Nagar Plain marble |
| 122 | Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 fine sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 123 | (i) 8mm thick Rajnagar marble tiles (polished) |
| 124 | Providing and fixing 1st quality ceramic glazed wall tiles (minimum 200 x 300) conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) ofapproved make in all colours, shades of any size asapproved by Engineer-in-charge in skirting, risers ofsteps and dados, laid over 12 mm thick bed of cementmortar 1 : 3 (1 cement : 3 fine sand) jointed withordinary cement slurry including pointing with whitecement mixed with pigment of matching shade complete. |
| 125 | Providing and laying ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete. |
| 126 | (i) Mat Finish Tiles - Ceramic Tiles 1st quality 400 x 400mm in all shades and designs |
| 127 | (ii) Anti Skid Tiles - Ceramic Tiles 1st quality 400 x 400mm in all shades and designs |
| 128 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 129 | (i) Double charged Stainfree vitrified tiles - Size of tile 60 x 60 cm |
| 130 | Providing and fixing precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry including rubbing and cleaning complete as per direction of the Engineer-in- Charge. |
| 131 | Providing and fixing 25 mm thick wooden planking, tounged and grooved in floors including fixing with iron screws complete. |
| 132 | (i) With Teak wood local |
| 133 | Providing and fixing Kota stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishingcomplete. |
| 134 | (i) Kota stone slab 25 mm thick |
| 135 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1 : 3 ( 1 cement : 3 fine sand ) and joined with ordinary cement slurry mixed with pigment to match the shade of slabs, including rubbing and polishing complete. |
| 136 | Providing and fixing tactiles of standardized designs conforming to RNIB (The Royal National Institute for the Blind, UK), DETR (Department of the Environment, Transport and the Regions, UK) & ADA (Americans with Disabilities Act, USA) of size 300 x 300 mm in floors, (thickness to be specified by the manufacturer) specially designed to assist the visually impaired - “foot braille”, with water absorption less than 0.5%, of approved brand & manufacturer, laid on 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) including grouting of joints (Payment for grouting of joints to be made separately) |
| 137 | 80 mm thick factory made c.c.interlockingpaver block of M-35 Grade Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge: (i) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. |
| 138 | SUB-HEAD : ROOFING AND CEILING WORK |
| 139 | Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 140 | (i) 0.50mm thichness |
| 141 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet shouldhaveprotective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimumto avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm: |
| 142 | (i) 0.50mm thichness |
| 143 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, |
| 144 | the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , of joint and two coats of primer suitable for board, all as per manufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer- incharge and as per manufacturer"s specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60. |
| 145 | ProvidingandfixingonwallfaceunplasticisedRigidPVCrainwater pipes (working pressure 4 kg/cm2)conformingto IS : 13592 Type Aincludingjointingwith sealring conformingtoIS:5382leaving10mmgapforthermalexpansion: |
| 146 | (i) Single socketed pipe - 110 mm OD |
| 147 | Providingandfixing on wallface unplasticised - PVCmouldedfittings/ accessoriesfor unplasticised Rigid PVC rain water pipes conforming to IS:13592TypeAincludingjointingwith sealringconformingtoIS: 5382 leaving 10 mm gap forthermalexpansion: |
| 148 | (i) Coupler - 110mm |
| 149 | (ii) Single equal tee without door - 110 x 110 x 110 mm |
| 150 | (iii) Single equal tee with door - 110 x 110 x 110 mm |
| 151 | (iv) Bend 87.5 - 110mm |
| 152 | (v) Plain shoe - 110 mm |
| 153 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. |
| 154 | (i) 110mm |
| 155 | Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. |
| 156 | (i) 100mm |
| 157 | SUB-HEAD : FINISHING WORK |
| 158 | 12 mm cement plaster of mix |
| 159 | (i) In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 160 | (ii) In cement mortar 1 : 6 ( 1 cement : 6 fine sand ) |
| 161 | 15 mm cement plaster on the rough side of single or half brick wall of mix: |
| 162 | (i) In cement mortar 1 : 6 ( 1 cement : 6 fine sand ) |
| 163 | (ii) In cement mortar 1 : 4 (1 cement : 4 fine sand) |
| 164 | 6 mm cement plaster of mix: |
| 165 | (i) In cement mortar 1 : 3 ( 1 cement : 3 fine sand ) |
| 166 | Neat cement punning. |
| 167 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i) New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 168 | Finishing walls with premium acrylic smooth exterior paint with Silicon additives of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i) New work ( two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 169 | Applying priming coat: [Payment shall be made after submission of Test Certificate issued by the Manufacturer] |
| 170 | (i) With ready mixed pink primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 171 | (ii) With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 172 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: (i) Two or more coats on new work |
| 173 | SUB-HEAD:WATER PROOFING WORK |
| 174 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with : |
| 175 | (i) Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 176 | (ii) Cement mortar 1:4 (1 cement : 4 fine sand ) |
| 177 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound, as directed by Engineer-in-Charge and consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 178 | SUB-HEAD : SANITARY WORKS |
| 179 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : |
| 180 | (i) White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 181 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : |
| 182 | (i) W.C. pan with ISI marked white solid plastic seat and lid |
| 183 | Providing and Fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : |
| 184 | (i) Range of four urinal basins with 10 litre white P.V.C automatic flushing cistern. |
| 185 | Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. |
| 186 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively. |
| 187 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings: |
| 188 | (i) Flat back wash basin of size 550x400mm. |
| 189 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: |
| 190 | (i) Kitchen sink without drain board - 610x460 mm bowl depth 200 mm. |
| 191 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 192 | (i) Semi rigid pipe - 32 mm dia |
| 193 | (ii) Flexible pipe - 32 mm dia |
| 194 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 195 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 196 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms |
| 197 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. |
| 198 | (i) 450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms |
| 199 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 200 | Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size ) including necessary plaster and pointing in cement mortar 1:4(1cement: 4 coarse sand): |
| 201 | (i) 100 mm dia. |
| 202 | Providing and fixing on wall face unplasticised Rigid PVC, soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382leaving10mmgapforthermalexpansion: (i) Single socketed pipe - 110 mm |
| 203 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC, soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap forthermalexpansion: |
| 204 | (i) Coupler - 110mm |
| 205 | (ii) Single pushfit Coupler - 110mm |
| 206 | (iv) Single equal tee without door - 110 x 110 x 110 mm |
| 207 | (v) Single equal tee with door - 110 x 110 x 110 mm |
| 208 | (vi) Doubleequal junction of required degreewithout door - 110 x 110 x 110 mm |
| 209 | (vii) Doubleequal junction of required degreewith door - 110 x 110 x 110 mm |
| 210 | (viii) Bend 87.5 - 110mm |
| 211 | (ix) Plain shoe - 110 mm |
| 212 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC , soil, waste & vent pipesbymeansof50x50x50mmhard woodplugs,screwedwithM.S.screwsofrequiredlengthincluding cutting brick work andfixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. (i) 110 mm |
| 213 | SUB-HEAD : WATER SUPPLY |
| 214 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. - Internal work -Exposed on wall |
| 215 | (i) 15 mm nominal outer dia .Pipes. |
| 216 | (ii) 20mm nominal outer dia .Pipes. |
| 217 | (iii) 25mm nominal outer dia .Pipes. |
| 218 | (iv) 32mm nominal outer dia .Pipes. |
| 219 | (v) 40mm nominal outer dia .Pipes. |
| 220 | (vi) 50mm nominal outer dia .Pipes. |
| 221 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. - Concealed work including cutting chases and making good the walls etc. |
| 222 | (i) 15 mm nominal outer dia .Pipes. |
| 223 | (ii) 20 mm nominal outer dia .Pipes. |
| 224 | (iii) 25 mm nominal outer dia .Pipes. |
| 225 | (iv) 32 mm nominal outer dia .Pipes. |
| 226 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. - External work |
| 227 | (i) 15 mm nominal outer dia .Pipes. |
| 228 | (ii) 20 mm nominal outer dia .Pipes. |
| 229 | (iii) 25 mm nominal outer dia .Pipes. |
| 230 | (iv) 32 mm nominal outer dia .Pipes. |
| 231 | (v) 40 mm nominal outer dia .Pipes. |
| 232 | (vi) 50 mm nominal outer dia .Pipes. |
| 233 | Providing and fixing brass bib cock of approved quality : |
| 234 | (i) 15 mm nominal bore |
| 235 | Providing and fixing brass stop cock of approved quality : |
| 236 | (i) 15 mm dia nominal bore |
| 237 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): |
| 238 | (i) 25 mm nominal bore |
| 239 | (ii) 40 mm nominal bore |
| 240 | Providing and fixing gun metal non-return valve of approved quality (screwed end): |
| 241 | (i) 25 mm nominal bore - Vertical |
| 242 | (ii) 40 mm nominal bore - Vertical |
| 243 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 244 | Constructing masonry Chamber 30x30x50 cm, inside , in brick work in cement mortar 1:4 (1 cement :4 fine sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished with a floating coat of neatcementcompleteasper standard design : |
| 245 | (i) With Second Class bricks |
| 246 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: |
| 247 | (i) 100 mm diameter |
| 248 | SUB HEAD : SEWAGE AND DRAINAGE WORKS |
| 249 | Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete : |
| 250 | (i) 150 mm diameter |
| 251 | Providing and laying cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) alround S.W. pipes including bed concrete as per standard design: |
| 252 | (i) 150 mm diameter S.W, pipe |
| 253 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 254 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : |
| 255 | (i) Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 256 | Extra for depth beyond 450 mm of brick masonry chamber for underground C.I. inspection chamber with same specification as mentioned in item no 20.330 complete as per standard design : |
| 257 | (i) For 500x700 mm size |
| 258 | SUB HEAD : INTERNAL ELECTRIFICATION WORKS |
| 259 | Wiring for light/ fan/ exhaust fan/ call bell point with 2x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type switch, cover plate, GI box including necessary connection etc. as required(As per TSR 2021, Sl- 401) . |
| 260 | Providing and fixing of 3 pin 6/10 amps plug point withmodulartype 6/10ampsswitch andsocketincludingconnectionwith 2 x 1.5 sq. mm PVC insulated Copper conductor cable (FR) onmodular concealedswitch board with cover plate earthing the 3rd pin etc. as required. (As per TSR 2021, Sl- 403) |
| 261 | Providing and fixing of 3/6 pin 16/20 amps plug point withmodulartype 16/20ampsswitch andsocketincludingconnectionwith 2 x 2.5 sq. mm PVC insulated Copper conductor cable (FR) onmodular concealedswitch board with cover plate earthing the 3rd pin etc. as required. (As per TSR 2021, Sl- 404) |
| 262 | Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall etc. as required:- (As per TSR 2021, Sl- 405) |
| 263 | a) 2 X 2.5 + 1 X 1.5 sq mm |
| 264 | b) 2 X 4 + 1 X 1.5 sq mm |
| 265 | c) 4 X 6+ 2 X 2.5 sq mm |
| 266 | d)4 X 10+ 2 X 4 sq mm |
| 267 | Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in existing PVC casing capping/conduitin recess/surfaceincluding connection etc. as required:- (As per TSR 2021, Sl- 503) |
| 268 | a) 2 X 1.5 sq mm |
| 269 | Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as required.(As per TSR 2021, Sl- 603) |
| 270 | a)19/20 mm dia |
| 271 | b)25 mm dia |
| 272 | EARTHING |
| 273 | Earthing with 40 mm dia G.I. Earth pipe (medium gauge) 4.5 m. long complete with masonry enclosure on top CI cover plate size 12"x 12" having locking arrangement including CC work, holes on earth pipe etc. as required:- (As per TSR 2021, Sl- 701) |
| 274 | Extra for using salt (5 kg) and charcoal (46kg) for pipe earth electrode as required:- (As per TSR 2021, Sl- 702) |
| 275 | Providing and fixing / drawing of 4.06 mm dia (8 SWG) G.I. wire on surface or in existing G.I/ PVC/ Polythene pipe for loop earthing as required:-(As per TSR 2021, Sl- 706) |
| 276 | Providng and laying 15mm dia(medium gauge) G.I. pipe for drawing of4.06mm (8SWG) dia G.I./ Copper wire forearth connection from earth electrodes etc as required:- (As per TSR 2021, Sl- 710) |
| 277 | SWITCHGEARS & ACCESSORIES |
| 278 | Supplying & installation of powder coated sheet steelenclosure(MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connectionas required. (As per TSR 2021, Sl- 1208) |
| 279 | a)2 way SPN MCB DB (single door):- |
| 280 | b)(2+6) / 8way SPN MCB DB (Double door):- |
| 281 | c)4way horizontal TPN MCB DB (Double door):- |
| 282 | d)4way vertical TPN MCB DB suitable for FP MCCB incomer upto 125 amps (Double door):- |
| 283 | Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connectionas required:- (As per TSR 2021, Sl- 1215) |
| 284 | a)6 to 32 amps SP MCB:- |
| 285 | b)40 amps DP MCB:- |
| 286 | c)40/50/63 amps TP MCB:- |
| 287 | Supplying & installation of TP/FP MCCB of following ratings in the existing MCCB enclosure/ panel board including connection etc as required (Ics=100% of Icu with adjustable settings):-(As per TSR 2021, Sl- 1219) |
| 288 | a)16 to 100 amps FP MCCB, Breakingcapacity 16/18KA (Thermal Magnetic):- |
| 289 | b)16 to 100 ampsTP MCCB, Breakingcapacity 16/18KA (Thermal Magnetic):- |
| 290 | LUMINARIES |
| 291 | Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc.as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):-(As per TSR 2021, Sl- 1101) |
| 292 | a) Recessed/Surface mounted 1ft x 1ft decorative 16/18 watt LED panel light with integral driver and high quality polycarbonate diffuser:- |
| 293 | Supplying and fixing of following LED Tubes, retrofit bulbs/lamps for LED luminaries including necessary connection etc. as required:-(As per TSR 2021, Sl- 1103) |
| 294 | a)12 watt LED retrofit lamp with polycarbonate body and aluminium heatsink :- |
| 295 | FANS |
| 296 | Supplying & fixing of 1200 mm sweep white color AC ceilingfan capacitor typedouble ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR)(ISI marked, BEE 1star/minimum service value 4.0 m3/min/W) : -(As per TSR 2021, Sl- 802) |
| 297 | Supplying & installation of 225/230 mm sweep metalic body exhaust fan including connection etc as required:-(As per TSR 2021, Sl- 816) |
| 298 | Supplying & installation of shutter for 225/230/300 mm sweep metalic body exhaust fan in the existing hole as required:-(As per TSR 2021, Sl- 821) |
| 299 | Making different sizes of hole in the wall for fixing of exhaust fan including finishing the same with cement plastering and painting etc as required:(As per TSR 2021, Sl- 831) |
| 300 | OUTDOORS & ACCESSORIES |
| 301 | Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt):- (As per TSR 2021, Sl- 1102) |
| 302 | a)45 watt LED street light fixture with integral driver and secondary lens (IP 66):- |
| 303 | Supplying & fixing of G.I. pipe (medium gauge) bracket fabricated at suitable angle for fixing of outdoor light on wall/ RCC base with necessary MS clamp, nut, bolt etc as required:-(As per TSR 2021, Sl- 1501) |
| 304 | a) 40 mm dia:- |
| 305 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering,shuttering, finishing and reinforcement- 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size):--(As per TSR 2021, Sl- 1519) |
| 306 | Supplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required(As per TSR 2021, Sl- 1301) |
| 307 | a) 4 core 4 Sq mm |
| 308 | Drawing of armoured/un-armoured cable with proper saddling etc as required:-(As per TSR 2021, Sl- 1511) |
| 309 | MISCELLANEOUS |
| 310 | Supplying and fixing of the following electrical accessories including necessary connection etc. as required.(As per TSR 2021, Sl- 604) |
| 311 | b) 32 amps DP kit kat switch:- |
| 312 | c) Electronic 5 step fan regulator:- |
| 313 | Supplying and fixing of 20 mm dia extra down rod (GI Pipe Medium Guage) with necessary hole for installation of ceiling fan as required(As per TSR 2021, Sl- 830). |
| 314 | Supplying & fixing of 40 mm dia G.I pipe (medium gauge) cross bar for fixing of ceiling fan/luminaries including painting & necessary accessories etc as required.(As per TSR 2021, Sl- 1505) |
| 315 | Supplying & fixing of 40mmx6mm MS clamp for installation of ceiling fan/luminaries on cross bar including necessary accessories etc as required(As per TSR 2021, Sl- 1506):- |
| 316 | Supplying and fixing of Copper terminal ends (LUGS) - long barrel of following sizes(As per TSR 2021, Sl- 1402): - |
| 317 | a)2.5 sq mm |
| 318 | b)6 sq mm |
| 319 | c)10 sq mm |
| 320 | Supplying and fixing of MS frame made of (25mm x 25mm x 5mm) MS angle with necessary support by (40mm x 6mm) MS flat and 12 mm thick marine plywood on top, grouted on wall with 4 noslegs (25mmx25mmx5mm MS angle20 cm long) finishedwith red oxide and 2 coat synthetic enamel paintincluding necessary cc work, mending the damages & painting etc as required:- (As per TSR 2021, Sl- 1502) |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
