|
| 1 | Dismantling wood work of area below 40 sq.cm. wrought framed and fixed in frames, other frames and trusses including stacking of material within 50 mts. Lead |
| 2 | Dismantling doors, windows and clearestory windows (steel or wood) shutters including chowkhats architrave holdfast etc. complete and staking within 50 mt. Lead |
| 3 | Of area 3 sq.m. and below |
| 4 | Extra for dismantling trusses, rafters, purlins etc. of wood work for every additional span of 1 mt. of part thereof beyond 10 meters. |
| 5 | Sectional area below 40 sq. cm.s |
| 6 | Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm. |
| 7 | Dismantling tiled roofing (mangalore or pot or country tiles) with battens etc. complete including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead. |
| 8 | Providing & fixing insulating board board sheet ceiling of approved of quality with necessary nails, etc.complete (frame for base to be paid separately) |
| 9 | White faced insulating board 12mm thick |
| 10 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of (SAIL, TATA. VIZAG, JSW ,APOLLO Steel Ltd.) make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and boltedwith special shaped washers etc. complete. |
| 11 | Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge. |
| 12 | Add for providing & fixing Flashings -[Corners, Ridges, valleys, gable end & Trims] (Girth upto 610mm) including all the accessories complete as per the directions of the Engineer in charge. |
| 13 | Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. |
| 14 | 15 mm dia nominal outer dia pipes. |
| 15 | Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand ;4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement ;2 coarse sand :4 graded stone agrregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cemetn and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design. |
| 16 | Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg). |
| 17 | Proving and fixing white vitreous china water closet squating (European type w.c. pan) with seat and lid,C.P. brass hingesand rubber buffers 10 lts. Highlevel P.V.C..flushing cistern (of approved make ) with fittings, rack bolts 32 mmdiameter P.V.C.telescopic flush pipe with fit tings and clamps 25mm P.V.C.. over flow pipe withspecials & mosquito proof coupling of approved municipal design and nylon. chain and pull complete, cutting and making good the walls ad floors where required. |
| 18 | W.C. pan with white plastic seat and lid. |
| 19 | Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass trap and union complete, including cutting and making good the walls where required. |
| 20 | Flat back wash basin size 550 x 400mm with a single 15 mm C.P. brass pillar taps. |
| 21 | Providing and fixing brass bib cock (heavy) of approved quality : |
| 22 | 15 mm nominal bore |
| 23 | Providing and fixing brass stop cock (heavy) of approved quality : |
| 24 | 20 mm nominal bore |
| 25 | Making soak pit. 2.5 m dia 3 m deep with 45x45 cm dry brick honey comb shaft and S.W. drain pipe 100 mm diameter, 1.8 m long complete filled with laterite stone aggregate 125 to 180 mm surrounded by laterite stone aggregate of 40 mm and down gauge as per standard design. |
| 26 | Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes ofapproved including lubricant etc. complete (single/double) socketed: |
| 27 | 110 mm dia |
| 28 | Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend withdoor : |
| 29 | 110 mm dia |
| 30 | Providing and fixing nahani trap ofrigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door : |
| 31 | 110 mm dia |
| 32 | Providing and fixingU.P.V.C. pipeclips (approved make ) for S.W.R. pipes: |
| 33 | 110 mm dia |
| 34 | Providing and fixing R.P.V.C. vent cowl: |
| 35 | 110 mm dia |
| 36 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone and making good the walls wherever required. Kitchen sink without drain board. with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete. |
| 37 | Overall size 535mm x460mm (21\"x18\") bowl size 460mm x380mm x200mm (18\"x 15\"x 8\") depth 200 mm. Glossy. 1.0mm thk, |
| 38 | Earthwork in surface excavation not exceeding 30 cm depth(but exceeding 1.5 m width as well as 10 sq.m on plan) including disposal of excavated earth beyond work site for all leads lift disposed earth to be leveled and neatly dressed in: |
| 39 | Ordinary soil |
| 40 | Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations |
| 41 | Providing & laying cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: |
| 42 | All works upto plinth level |
| 43 | 15mm cement plaster 1: 3 (1 cement : 3 fine sand) on the rough side of single or half brick wall. |
| 44 | 18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge. |
| 45 | Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: windows with two sliding shutters using 18 mm series shutters section. |
| 46 | Figured glass |
| 47 | Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section |
| 48 | Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in positon. |
| 49 | First class matti wood |
| 50 | Providing and fixing 35 mm thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory window including anodized aluminium butt hinges with necessary screws: |
| 51 | First class Indian teak wood |
| 52 | Providing& fixing flush door shutters decoration type core of block board construction with frame of first class hard wood and well matched first class Indian teak ply veneeringwith vertical grains and cross bands and face veneers on both faces of shutters. |
| 53 | 30 mm thick including anodized aluminium butt hinges with necessary screws: |
| 54 | Providing flat iron hold fast 40 cm including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embeded in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 stone aggregate 20 mm nominal size. |
| 55 | 40 x 3 mm flat iron hold fast, 15 cm long |
| 56 | Wood Finish Foam Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system, with seasoned hard wood, moisture less than 17%, wood styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) along with printed matt having wooden textures, used along with UV Resistant resin to give the clear wooden texture on the door. The core of shutter will be filled as specified (Expanded Polystyrene Foam / Polyurethane Foam (EPS/PU) Foam) The shutter to be water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) Technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory. |
| 57 | i) S. S. Hinges 4” - 3 No,ii) S. S. Latch - 1 No iii) Tower Bolt 5” - 2 Nosiv) Handle 5” - 2 NosShutter Thickness : a) 30mm |
| 58 | FRP (Fiber Reinforced Polymer) Frames Manufacture, Supply and Installation (with anchor fastener) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) Frame of cross section as per options below with right angle joint and FRP (Fiber Reinforced Polymer) laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber (matt) and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps). The core of frame would be filled with seasoned wood as infill material. The slot of frame for door resting will be of suitable width so as to take specified thickness door.. The frame will be water proof as well as mild acid/ alkali resistant manufactured in an ISO 9001- 2015 certified company. |
| 59 | Specified Cross Sectionc) 4” x 2 ½ “ |
| 60 | Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws. |
| 61 | Plain grill |
| 62 | Providing and fixing chromium plated brass sliding door bolt with bolts, nuts and screws etc. complete. |
| 63 | 300x16mm |
| 64 | Providing and fixing chromium plated brass handle with necessary screws etc. complete |
| 65 | 125mm |
| 66 | Providing and fixing anodised aluminium sliding door bolt anodised transparent or dyed required colour and shade with bolts, nuts and screws etc. complete: |
| 67 | 300 x 16 mm |
| 68 | Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 69 | Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade. |
| 70 | Painting three or more coats with acryllic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat of surface treatment etc. complete. |
| 71 | Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture in all shade or new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture to give an even shade |
| 72 | Making plinth protection 50mm thick of Cement Concrete 1:3:6 (1cement: 3 Coarse Sand: 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry laterite aggregate 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 73 | Laying manglore roofing tiles, ridges, valleys etc. complete on roofs over existing battens rafters etc. (Tiles to be issued by the department). |
| 74 | Machine polshing mirror polish of kota stone flooring, washing, cleaning and applying final coat of wax polish |
