Military Engineer Services-MES has published Tender For Repair / Maintenance To Floor, Plastering, Tiling Roofing, Ac Sheet With False Ceiling And Certain Other Connected B / R Work In Zone A, B, C And D At Old Cantt Prayagraj.. Submission Date for this Tender is 12-08-2023. Shed Construction Tenders in prayagraj Uttar Pradesh. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 2 | Demolition of reinforced cement concrete in landing, chajjahs or kitchen plateform reinforcement cut as requiredto facilitate complete all as specified and directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed. |
| 4 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc ,laid bedded pointed in any mortar offloor, including cement mortar bedding complete all as specified and directed. |
| 5 | Taking down existing cementplaster wall/ ceiling including racking out joints, hacking for key, scrubbing down with water etccomplete all asspecified and as directed. |
| 6 | Demolition of brick or stone masorny built in cement mortar including all necessary arches, quoins, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. |
| 7 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 Sqm and not exceeding 0.11 Sqm each in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 8 | Glazed ceramic coloured tiles 300 mm x450 mm x 6 to 7 mm thick, in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 10 mm thick rendring in CM (1:4) complete all as specified and directed. |
| 9 | M&L for non skid joint free ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 Sqm and not exceeding 0.18 Sqm each in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 10 | All as per Item No-9 above but as in vertical surfaces such as skirting/ dado over and including rendering 10 mm thick in CM (1:4) complete all as specified and directed. |
| 11 | M&L Vitrified Ceramiccolour tiles 8 to 10 mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM1:6 complete all as specified and directed. |
| 12 | As per Item No-11 above but as on vertical surfaces such as skirting/ dado over and including screed bed or bedding layer 10 mm thick in CM (1:4) complete all as specified and directed. |
| 13 | M&L Exterior Heavy duty full body coloured paving tiles of size 300X300x8 to 9 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15 mm thick screed bed or bedding layer in cm (1:6) over 25 mm thick pcc 1:2:4 as in levelling course complete all as specified and directed. |
| 14 | M & L Machine Cut Granite 18-20 mm thick table rubbed and polished counter top,cooking plateform bedded & jointed with grey cement slurry and pointed with white cement mixed admixture of pigment to match the shade of granite including cutting, polishing and moulding edges including 15 mm thick screed bed or bedding layer in cm (1:6) complete all as specified and directed. |
| 15 | Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 16 | M & L Machine cut baroda Green marble stone slab 18 to 20 mm thick laid over Kitchen cooking platform in 20 mm thick cement screed mortar (1:6) laid and jointed in grey cement slurrry mixed with pigment to match the shade of the slab incl cutting, rubbing and polishing complete and incl nosing of the edges half round (Stone slab shall fixed in two piece). including 20 mm thick screed bed in cm 1:4 complete all as specified and directed. |
| 17 | M&L for Cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate in plinth protection, 50 mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at the length n exe 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed. |
| 18 | M & L PCC 1:4:8 type D-2 using 40 mm graded aggregate 75 mm thickas in sub base of floor etc complete all as specified and as directed. |
| 19 | M&L Cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in floors, 40 mm thick, laid in panels fixed with glass dividing strip and finished even & smooth using extra cement complete all as specified and directed. (Note Glass dividing strip shall be measured and paid separately.) |
| 20 | Supply & fixing only Glass dividing strips, 3 mm thick and 38 mm wide, inserted in position in floors complete all as specified and directed. |
| 21 | M&L PCC (1:2:4) type B-2 (40 mm graded agg) 100 mm thick laid in alternate panels including use and waste of form work finished even and smooth without using extra cement complete all as specified and directed. |
| 22 | Material and labour for precast reinforced cement concrete as in cover slabs, etc type B1 1:2:4 using 20 mm graded agg. set in cement mortar 1:4 complete all as specified and directed. |
| 23 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 24 | M&L brick work with Sub class B Bricks , straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 25 | Description all as per item No.24 here in above but except bricks complete all as specified and directed. |
| 26 | M & L 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4as in drain, bdy wall etc finished even and smooth complete all as specified and as directed. |
| 27 | M & L 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4 mixed with water proofing compound, surface finished even and smooth including 2 coat of cement base paint over a coat of cement primer and preparation of new plastered surface complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately as supply only. |
| 28 | M & L Rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extrs cement complete all as specified and directed. |
| 29 | M&L for Rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished fair & even complete all as specified and directed. |
| 30 | Supply only integral water proofing compound. |
| 31 | M&L for plain Cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate in roof curbs, mud stops or chamfered on edges all as directed including necessary form work complete all as specified and directed. |
| 32 | Cleaning the sunken floor surfaces by wire brushes, brooming, removing dust by dismentling of floor, lime terracing and applying following :- (a) Bitumen primer confirming to IS-3384-1965 @ 0.50 Kg Per sqm. (b) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 Kg/Sqm confirming to IS – 702-1998 for water proofing membrance. (c) Applying of polymeric water proofing membrance weight not less than 3 Kg/Sqm over entire are with overlaps and sealed all as specified directed. (d) Again applying a tack coat ofhot blown bitumen 85/25 @ 1.2 Kg/Sqm over water proofing membrance. (e) Dusting dry sand @ 0.75 Kg PerSqm over water proofing membrance. (f)Fixing of GI pipe spout 50mm of adequate size complete. |
| 33 | PCC 1:5:10 type E-2 using 40 mm graded stone aggregate for filling up sunken floor over felt/sub base of floor complete all as specified and directed. |
| 34 | Taking up or down steel tubing and connections 15 mm bore complete all as specified and directed. |
| 35 | Taking up or down steel tubing and connections 20 mm bore complete all as specified and directed. |
| 36 | S & F Galvanised mild Steel water tubes, medium grade, ISI marked, , 15 mm bore Galvanised with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. |
| 37 | S & F Galvanised mild Steel water tubes, medium grade, ISI marked, 20 mm bore Galvanised with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. |
| 38 | Refixing old 15 mm dia boresteel water tubing& connection in new or old positionfixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fittings such as elbows, tees, sockets, union,reducer, etc as required complete all as specified and directed. |
| 39 | Refixing old 20 mm dia boresteel water tubing& connection in new or old positionfixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fittings such as elbows, tees, sockets, union, reducer, etc as required complete all as specified and directed. |
| 40 | S&F in repair rotational moulded HDPEwite colour tripple layer water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms) complete all as specified and directed. |
| 41 | S&F in repair rotational moulded HDPEwite colour tripple layer water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms) complete all as specified and directed. |
| 42 | S & F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for ironpipe and fixedcomplete all as specified and directed. |
| 43 | S & F in repairball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic wall, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210gms), complete all as specified and directed. |
| 44 | S&F in repair PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, 75 mm bore complete all as specified and directed. |
| 45 | S&F in repair PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, 110 mm bore complete all as specified and directed. |
| 46 | S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed. |
| 47 | S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed. |
| 48 | S&F in repair PVC (SWR) junction single (single T), equal or unequal, 75 mm bore, provided with access door complete all as specified and directed. |
| 49 | S&F in repair PVC (SWR) junction single (single T), equal or unequal, 110 mm bore, provided with access door complete all as specified and directed. |
| 50 | S&F Stack clamps out of 50 mm by 5 mm flat iron and iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm Bore of pipe complete all as specified and directed. |
| 51 | S&F Stack clamps out of 80 mm by 5 mm flat iron and iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm Bore of pipe complete all as specified and directed. |
| 52 | S&F in repair 75 mmPVC (SWR) floor trap, plain with grating including jointing with solvent cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) complete all as specified and as directed. |
| 53 | S&Fin repair 600mmx 450mm looking mirror of selected quality ofoval shapeglass, mounted on 6mm thick AC building board or commercial ply woodwith PVC frameincluding all necessary fixing arrangement & fixed to wooden plug with chromium plated brass screws and cup washers complete all as specified and directed. |
| 54 | S & F in repair kitchen Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboaratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including supply and fixing cantilever brackets of mild steel angle 35 mm x 35 mm x 5 mm, 32mm dia brass waste coupling ,32 mm dia PVC waste pipe (rigid quality) and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410 mm x 330 mm x 160 mm, complete all as specified and directed. |
| 55 | S&F in repair 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete all as specified and directed. |
| 56 | S & F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15 mm bore complete all as specified and directed. |
| 57 | S&F in repair 15 mm size bib tapscast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and directed. |
| 58 | S&F in repair grating round 100 mm dia of PTMT (minimum weight 100 gms) fixed in repair complete all as specified and directed. |
| 59 | S&F in repairs square grating 150 mm size of PTMT (minimum weight 100 gms) complete all as specified and directed |
| 60 | Supply & fixing only pillar tap cast copper alloywith capstin heads chromimium platedfancy type screweddown high pressure with or without lettered hot or coldwith long screwed shank and fly nuts, screwed for iron pipe 15 mm bore complete all as specified and directed. |
| 61 | S & F in repair Brass chromium plated shower rose65mm to 90 mm size with swivel joints, complete all as specified and directed. |
| 62 | S&F in repair 10 litre capacity PVC low level cistern ‘white’ with inlet, float valve including bracket with 32mm dia PVC pipe 600 mm long complete all as specified and directed. |
| 63 | S&F in repair PVC connection 600mm long and 15 mm dia with brass fly nut at both ends complete all as specified and directed. |
| 64 | S & F Stainless steel plate rack (utensil rack) of size (600 mm x 750 mm) and depth 250 mm made with 0.63 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts including taking down old u/s plate rack complete all as specified and directed. |
| 65 | S&F in repair25 mm dia stainless steel drapery rod cut to size and fixed in position including brackets, side domsfixed to wall complete all as specified and directed. |
| 66 | S&F in repair PVC waste pipe 32mm dia complete all as specified and directed. |
| 67 | S&F in repair PVC waste pipe 40mm dia complete all as specified and directed. |
| 68 | S&F in repair Door Seal length of each door seal is equal to width of door fixed to door bottom rail including all fixing arrangement such as screws, nails etc complete all as specified and directed. |
| 69 | S&F in repair vitreous china squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe,CI trap 100 mm Bore of pipe etc complete all as specified and directed. |
| 70 | S & F in repair vitreous China wash hand basin white flat back of size 550 mmx400mm fixed oncantilever brackets of mild steel a 32mm dia brass waste coupling completed all as specified and directed. |
| 71 | S&F in repairs vitreous china wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat coverincluding connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with aluminium hinging device complete all as specified and directed. Note : Plastic seat cover shall be measured separately as Supply only as considered under respective items. |
| 72 | Supply & fixing only water closet seat cover closed pattern with flat bottomand mild steel chromium plated or aluminium hinging device complete all as specified and directed. |
| 73 | Taking down chowkhat or frames with shutters (without taking off shutters from the frames) areanot exceeding 1.5 but each and removing from site complete all as specified and directed. |
| 74 | Taking down chowkhat or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 but not exceeding 4 Sqm each and removing from site complete all as specified and directed. |
| 75 | Taking down shutter of any description, exceeding 1.00 Sqm but not exceeding 2.00 Sqm each complete all as specified and directed. |
| 76 | Taking down shutter of any description,not exceeding 1.00 Sqm each complete all as specified and directed. |
| 77 | M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in hold fasts including necessary use and waste of form work complete all as specified and directed. |
| 78 | S & F Mild steel work as in wind ties/hold fast etc confirming to Fe 290 gde E 165 complete all as specified and directed. |
| 79 | M&L for Rolled mild steel sections conforming to Gde Fe-410-W or Fe-310-W as in framing for cladding, glazing and the like including door frames/ chowkats, cooler stand,gate and door shutter etc fixed with angle cleats and connecting plates, etc complete all as specified and directed. |
| 80 | S & F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 81 | S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MSframe shall be covered with heat molded plain colourPVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part – II 2004 and as directed by GE/Engineer-in-Charge |
| 82 | S&F 35 mm thick factory made 2nd class Hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges offraming plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats |
| 83 | S & F Flush shutters 32 mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete all as specified and directed. |
| 84 | S&F 250 mm long aluminium sliding door bolts, bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. |
| 85 | S&F150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 86 | S & F 100 mm Butt hinges medium weight cold rolled mild steel complete all as specified and directed. |
| 87 | S&F 100 mm long Butt hinges, extrucded aluminium alloy withbrass/bronze hinge pin, anodised type B-21 , bright polished type B-11 complete all as specified and directed. |
| 88 | S&F aluminium handles 150mm size cast type, anodised complete all as specified and directed. |
| 89 | S & F in repair 150 mm aluminium anodised hasp and staple complete all as specified and directed. |
| 90 | S & F in repair 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed. |
| 91 | M&L 18/19mm Block boards, grade 2 quality, in terior grade, commercial type, fixed with screws to timber frame-work complete all as specified and directed |
| 92 | S & F in repair factory made steel window with side hung shutter including box type hinges with steel handle, steel peg stay, complete with glazing bar, dovetailed or welded complete all as specified and directed. |
| 93 | S & Ffactorymade in repairsteel window with side hung shutter including box type hinges with steel handle, steel peg stay, complete without glazing bar, dovetailed or welded complete all as specified and directed. |
| 94 | S&F in repair factory made Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed. |
| 95 | S&F in repair Aluminium (Diecast) body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed.complete all as specified and directed. |
| 96 | Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mildheavy duty and fixed complete all as specified and directed. |
| 97 | Anodised aluminium frame for doors, windows, ventilators powder coated (Thickness or powder coating not less than 50 micron ) with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 98 | Anodised aluminium door shutters, powder coated (Thickness or powder coating not less than 50 micron ) aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed. |
| 99 | Anodised aluminium window and ventilator shutters, powder coated (Thickness or powder coating not less than 50 micron ) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges typeB-21 100mm long (2 No.) suitable handle (1 No.), tower bolt 100mm long (1 No) complete all as specified. |
| 100 | Sheet glass, 4.8mm ordinary quality and glazing with oil putty in squareexceeding0.5 sq. m in each pane complete all as specified and directed. |
| 101 | Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of gradeAC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge |
| 102 | Prelaminated particle board, 12mm interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. |
| 103 | Mild Steel mortice lock four lever vertical type of size 100 mm with all fittings, fixed in repairs, complete all as specified and directed. |
| 104 | Providing and fixing in repair E-boardMake: Everest, Design "Lake and Hill" of size 605 x 605 x 4mm thick white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section (White powder coated). The framework shall comprise of main runner made from 0.33mm thick GS sheet and of size 24 x 32x x300mm and soaced at 1200mm maximum centres securely fixed to structural soffits with hangers of 2mm dia GI wire to be fixed with approved rawl plugs, adjusters and screws. Flush fitting of 1200mmm long cross Tee (with double stiching) to be interlocked between main runners at 600mm centre to form 1200 x 1600 mm modules cross tee longer than 600mm to be supported independently. 600 x 600mm doubles to be formed by fittings 600mm long cross tee centrally between the 1200mm cross tee. Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19 x 19 mm and 300mm long of white colour all as per manufacturers instructions complete all as specified and directed. |
| 105 | S&F in repair for providing and fixing E-boardMake: Everest, Design "Lake and Hill" of size 605 x 605 x 4mm thick white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on old / existing frame work all as per manufacturers instructions complete all as specified and directed. |
| 106 | Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges as in roof covering complete all as specified and directed. |
| 107 | S & F 6 mm thick asbestos cement corrugated sheet fixed with ‘L’ type or ‘J’ type or cranked hook bolts complete all as specified and directed. |
| 108 | Dittoas per item No. 107above but except sheet complete all as specified and directed. Note : Old serviceable AC sheet obtained from dismantling shall be re-used. |
| 109 | S & F 6 mm thick asbestos cement two piece adjustable plain wing ridge fixed with ‘L’ type or ‘J’ type or cranked hook bolts complete all as specified and directed. |
| 110 | S & F in repair pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensilestrength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 111 | S & F in repair pre-painted galvalume aluminium zinc coating GI based plainsteel sheet 0.50 mm thick of an colour having tensilestrength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 112 | Dismantling timber scantlings 40 Sqcm and over in section, in unframed work in any position complete all as specified and directed. |
| 113 | 2nd class soft wood clean sawn timber fixed in scantling complete all as specified and directed. |
| 114 | 2nd class soft wood clean sawn timber fixed in scantling complete all as specified and directed. (Expect Timber) |
| 115 | Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote oilcomplete all as specified and directed. |
| 116 | S&F in steel conforming to Fe 410-0 or Fe 310-0 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed. |
| 117 | S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and directed. |
| 118 | S & F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and directed. |
| 119 | Hacking out old broken glass (any thickness, size, quality or description) from metal/wooden frame complete all as specified and directed. |
| 120 | S & F 04 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in square area not exceeding 0.5 Sqm in each pane complete all as specified and directed. |
| 121 | S & F 04 mm thick frosted on one side sheet glass ordinary quality and glazing with oil putty or wooden beads in square area not exc. 0.5 Sqm in each pane complete all as specified and directed. |
| 122 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed. |
| 123 | S&F Roof trusses, trusses, purlins, rafter, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee, angle, chaneel, flat or squre tubes sections) including distance pieces Fe-290 (Fde E-165) complete all as specified and directed. |
| 124 | Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheett inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. |
| 125 | PVC Frame including 3 mm thick PVC Sheet fillet of width 35 mm for wall paneling incl of fixing on to wall to PVC Frame as per specification and drawing, fixed in repair, complete all as specified and directed. |
| 126 | Cleaning of HDPE tank of capacity up to & including 500 Litres by Flushing out water cleaning & removing of sludge, scale mud etc from wall & floor by rubbing with brushes, cleaning with caustic soda etc complete & finally washing with fresh water, including writing date of cleaning with white synthetic enamel paint and removing sludge, scale mud etc to a distance not exceeding 50 metre and depositing complete all as specified and directed. |
| 127 | All as per item No. 126 above but capacity of tankexceeding 500 litre but not exceeding 1000 litrescomplete all as specified and directed. |
| 128 | M & L applying two coats of synthetic enamel paint on newwooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed. |
| 129 | M&L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10cm width or girth over a coat of red oxide including preparation of steel surfaces complete all as specified and directed. |
| 130 | M&L for applying two coats of oil bound distemper over one coat of chalk whiting onnew plastered surfaces preparating to distempering on walls including preparation of surface complete all as specified and directed. |
| 131 | Preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 132 | S&F Spot welding in repairs to existing butt hinges 100 mm /single action spring hinges/ double action spring hinges/projecting type hinges/box type hinges by welding the same to existing door frame/mild steel window frame complete all as specified and directed |
| 133 | Supply and fixing in repairs 40mm dia Sink coupling of PTMT (half or full threaded) (Minimum weight 32mm - 45gms/ 40mm - 60gms complete all as specified and directed. |
| 134 | Supply and fixing in repairs 32mm dia WHB coupling of PTMT (half or full threaded) (Minimum weight 32mm - 45gms/ 40mm - 60gms) complete all as specified and directed. |
| 135 | M&L for preparing old decorated plastered or unplastered surfaces of wall including cornices, pilasteredetc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt andtrading oil and greasy spots and applying one coat of oil bound distemper (approved colour/ shade) complete all as specified and directed. |
| 136 | M&L for preparation of old plastered surface and applying two coat of oil bound distemper on walls over a coat of primer and 1 mm thick wall care puttyincluding complete removal of existing treatment complete all as specified and directed. |
| 137 | M&L for preparing old decorated plastered surfaces of wall including cornices, pilasteredetc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt andtrading oil and greasy spots and applying one coat of cement base paint on wall surface complete all as specified and directed. |
| 138 | M&L for preparing old decorated plastered surfaces of ceilingincluding cornices,pilasteredetc by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt andtrading oil and greasy spots and applying one coat of white wash on ceilingcomplete all as specified and directed. |
| 139 | Toughned glass 12mm thick as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required incl all necessary fittings suchasverticle handle, stainless steel angles, screws etc complete all as specified and directed. |
| 140 | S&F aluminium composite panel sheet 3 mm thick fixed with and including necessary backing aluminium tubes, joints of panel should be filled with silicon filling material and all panel will be fixed with screw, as in wall panelling ,ceilling or vertical surface complete all as specified and directed. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
