Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Earthwork in excavation of foundation in all kinds ofsoil includingdressing and levelling the bed up to the required depth & removing the excavated earth & depositing the same away from the work site within initial lead of 50 mtr & initial lift of 1.5 mtr, including cost of labour T&P articles required for the work including shoring, shuttering, propping & dewatering if required, etc. complete in all respect as per the specification & direction of the Engineer-in-Charge. |
| 2 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 3 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 4 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 5 | Extra lift of 1.5m or part there of over the initial lift of in all kinds of embankments and road works and ordinary earth work in general. |
| 6 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 7 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 8 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 9 | Supplying all materials, labour,T&P and filling Foundation and Plinth with excavated earth includingwatering, ramming etc all complete as per direction of the E.I.C. |
| 10 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 11 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 12 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 13 | Carriage of excavated earth by mechanical means within 5 km leadcost of all labour, all T&P etc required for the work complete in all respect as per the direction of the Engineer-in-Charge. |
| 14 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 15 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 16 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 17 | Supplying and filling in foundation trenches and plinth with sand, well watered and rammed in layers not exceeding 23cm in depth with all lead and lift including cost, conveyance, loading, unloading, royalties of all materials, cost of all labour, sundries, T&P required for the work etc. complete in all respect as directed by the Engineer-in-Charge. |
| 18 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 19 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 20 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 21 | Plain Cement concrete (1:3:6) in foundation and floorsusing 40 mm size clean hard broken granite metal of approved quality from approved quarry with cost convenyeance, cost of all labour T&P ramming curing including hoisting and laying concrete in layer not exceeding 0.15 cum depth. Etc. complete as directed by the Engineer-incharge. |
| 22 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 23 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 24 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 25 | Providing, lifting, hoisting and laying reinforced cement concrete of M25 grade design mix using portland slag cement conforming to IS:455 to base of columns and footings, Pile cap, plinth band, lintels, chajja, shelf, fins roof slabs, balconies, stair case, ramps, parapets, window sills, lofts, railings and copings etc with 20mm downgraded hard crusher broken granite material of approved quality from approved quarry including weigh batching, mixing in approved mechanical concrete mixers in proportion to be determined by trial mixes and compacting to proper shape and size level and plumbsand maintaining the clear cover of concrete member notless than 45mm conforming to the approved pecification IS 456 and finishing the exposed surface smooth,scaffolding watering and curing for the required period as per direction of the Engineer-in-charge including cost of all materials with taxes royalities, transportation, loading and unloading, all labour undries T&P etc. but excluding costreinforcement barsincluding suitable plasticiser (of approved quality as per direction of Engineer-in-charge) to be used in concrete mix. |
| 26 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 27 | Foundation |
| 28 | Footing |
| 29 | Column upto plinth |
| 30 | Plinth beam |
| 31 | GroundFloor |
| 32 | Column |
| 33 | Roof beam |
| 34 | Roof Slab |
| 35 | Stair Case |
| 36 | Lintel |
| 37 | Sill |
| 38 | Chajja |
| 39 | FirstFloor |
| 40 | Column |
| 41 | Roof beam |
| 42 | Roof Slab |
| 43 | Stair Case |
| 44 | Lintel |
| 45 | Sill |
| 46 | Chajja |
| 47 | TerraceFloor |
| 48 | Column |
| 49 | Roof beam |
| 50 | Roof Slab |
| 51 | Lintel |
| 52 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 53 | Foundation |
| 54 | Footing |
| 55 | Column upto plinth |
| 56 | Plinth beam |
| 57 | GroundFloor |
| 58 | Column |
| 59 | Roof beam |
| 60 | Roof Slab |
| 61 | Stair Case |
| 62 | Lintel |
| 63 | Sill |
| 64 | Chajja |
| 65 | FirstFloor |
| 66 | Column |
| 67 | Roof beam |
| 68 | Roof Slab |
| 69 | Stair Case |
| 70 | Lintel |
| 71 | Sill |
| 72 | Chajja |
| 73 | TerraceFloor |
| 74 | Column |
| 75 | Roof beam |
| 76 | Roof Slab |
| 77 | Lintel |
| 78 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 79 | Foundation |
| 80 | Footing |
| 81 | Column upto plinth |
| 82 | Plinth beam |
| 83 | GroundFloor |
| 84 | Column |
| 85 | Roof beam |
| 86 | Roof Slab |
| 87 | Stair Case |
| 88 | Lintel |
| 89 | Sill |
| 90 | Chajja |
| 91 | FirstFloor |
| 92 | Column |
| 93 | Roof beam |
| 94 | Roof Slab |
| 95 | Stair Case |
| 96 | Lintel |
| 97 | Sill |
| 98 | Chajja |
| 99 | TerraceFloor |
| 100 | Column |
| 101 | Roof beam |
| 102 | Roof Slab |
| 103 | Lintel |
| 104 | Cutting, straightening coiled or bent up M.S. rods, HYSD steel or Tor Steel ofgrade Fe-500-D confirming to I.S.-1786 - 1985welding or jointing if necessary, bending, binding, tying the grills as required for RCC works, and hoisting, lowering and placing in proper position according to approved designs and drawings including cost, conveyance, loading, unloading of M.S. rods, HYSD steel or Tor steel and binding wires of 18 to 20 gauge required for the work and cost of all labour, sundries, T&P and scaffolding complete in all respect as directed by the Engineer-in-Charge (payment will be made according to the actual weight of M.S. rod, HYSD steel or Tor steel & binding work consumed in the work. |
| 105 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 106 | Foundation |
| 107 | GroundFloor |
| 108 | FirstFloor |
| 109 | TerraceFloor |
| 110 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 111 | Foundation |
| 112 | GroundFloor |
| 113 | FirstFloor |
| 114 | TerraceFloor |
| 115 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 116 | Foundation |
| 117 | GroundFloor |
| 118 | FirstFloor |
| 119 | TerraceFloor |
| 120 | Masonry work using Flyash Bricks of 250mm X 120mm X 80mm size having crushing strength not less than 75 kgs/ cm2 in cement mortar (1:6) with portland slag cement (PSC) immersing the bricks for minimum 6 hours in water before use with necessary projections, splays, cutting, circular moulding, corbelling etc. including cost, conveyance, royalties, loading and unloading of all materials and all labour for scaffolding, watering and curing, sundries, T&P etc complete as per direction of the Engineer-incharge as per approved specification. |
| 121 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 122 | GroundFloor |
| 123 | FirstFloor |
| 124 | TerraceFloor |
| 125 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 126 | GroundFloor |
| 127 | FirstFloor |
| 128 | TerraceFloor |
| 129 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 130 | GroundFloor |
| 131 | FirstFloor |
| 132 | TerraceFloor |
| 133 | Providing 12 mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) with approved grade cement and with screened and washed sharp sand for mortar and finished smooth to the rough surface of brick masonry walls after racking out joints including watering and curing, rounding of corners etc. complete with cost, conveyance, loading, unloading, royaltiesof all materials, cost of all labour, T&P, sundries and scaffolding required for the work etc. with providing grooves as directed by the Engineer in charge. |
| 134 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 135 | GroundFloor |
| 136 | FirstFloor |
| 137 | TerraceFloor |
| 138 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 139 | GroundFloor |
| 140 | FirstFloor |
| 141 | TerraceFloor |
| 142 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 143 | GroundFloor |
| 144 | FirstFloor |
| 145 | TerraceFloor |
| 146 | Providing 16 mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) with approved grade cement and with screened and washed sharp sand for mortar and finished smooth to the rough surface of brick masonry walls after racking out joints including watering and curing, rounding of corners etc. complete with cost, conveyance, loading, unloading, royalties of all materials, cost of all labour, T&P, sundries and scaffolding required for the work etc. with providing grooves as directed by the Engineer in charge. |
| 147 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 148 | GroundFloor |
| 149 | FirstFloor |
| 150 | TerraceFloor |
| 151 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 152 | GroundFloor |
| 153 | FirstFloor |
| 154 | TerraceFloor |
| 155 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 156 | GroundFloor |
| 157 | FirstFloor |
| 158 | TerraceFloor |
| 159 | Providing 6mm thick cement plaster with cement mortar of mix (1:4) with portland slag cement (IS 455) over a coat of cement wash to ceiling of roof slabs, stair, landings, chajja, shelf and lofts etc. including roughening chiseling, scraping and cleaning and finishing smooth as per direction of the Engineer-in-charge including cost of all materials, conveyance and royalties, scaffolding, watering and curing, sundries and T&P etc complete as per direction of the Engineer-in-charge as per approved specification. |
| 160 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 161 | GroundFloor |
| 162 | FirstFloor |
| 163 | TerraceFloor |
| 164 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 165 | GroundFloor |
| 166 | FirstFloor |
| 167 | TerraceFloor |
| 168 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 169 | GroundFloor |
| 170 | FirstFloor |
| 171 | TerraceFloor |
| 172 | Priming one coat with water bound cement primer to exterior plaster surface walls in all floors and all heights including preparing the surface, watering and curing with cost, conveyance, royalties of all materials and cost of all labour, scaffolding, sundries and T&P. etc. required for the work etc. complete as directed by the Engineer in charge. |
| 173 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 174 | GroundFloor |
| 175 | FirstFloor |
| 176 | TerraceFloor |
| 177 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 178 | GroundFloor |
| 179 | FirstFloor |
| 180 | TerraceFloor |
| 181 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 182 | GroundFloor |
| 183 | FirstFloor |
| 184 | TerraceFloor |
| 185 | Finishing surface of wall with cement based wall putty (water based) of approved make and finished smooth and even surface to receive painting including cost of scaffolding, staging charges with cost of all materials, labour,T&P etc complete as per direction of Engineer in charge. |
| 186 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 187 | GroundFloor |
| 188 | FirstFloor |
| 189 | TerraceFloor |
| 190 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 191 | GroundFloor |
| 192 | FirstFloor |
| 193 | TerraceFloor |
| 194 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 195 | GroundFloor |
| 196 | FirstFloor |
| 197 | TerraceFloor |
| 198 | Painting over interior plastered surfaces with two coats of plastic emulsion paint of approved quality and shade using the required quantity of paint as specified by the manufacturer to give an even shade including providing one coat of water bound cement primer and watering the surface before applying and curing for the required period as directed by the Engineer-in-charge including cost of all materials with transportation, all labour, scaffoldings, sundries T&P etc complete as per direction of the Engineer-in-charge as per approved specification. |
| 199 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 200 | GroundFloor |
| 201 | FirstFloor |
| 202 | TerraceFloor |
| 203 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 204 | GroundFloor |
| 205 | FirstFloor |
| 206 | TerraceFloor |
| 207 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 208 | GroundFloor |
| 209 | FirstFloor |
| 210 | TerraceFloor |
| 211 | Painting over exterior plastered surfaces with two coats of synthetic weather coat paint of approved quality and shade using the required quantity of paint as specified by the manufacturer to give an even shade including providing a primer coat as directed by the Engineer-in-charge including cost of all materials and transportation, all labour, scaffoldings, sundries T&P etc complete as per direction of the Engineer-in-charge as per approved specification. |
| 212 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 213 | GroundFloor |
| 214 | FirstFloor |
| 215 | TerraceFloor |
| 216 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 217 | GroundFloor |
| 218 | FirstFloor |
| 219 | TerraceFloor |
| 220 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 221 | GroundFloor |
| 222 | FirstFloor |
| 223 | TerraceFloor |
| 224 | Providing fitting Fixing 8mm to 10 mm thicknessVitrified tilesin all floors of size of 60cm X 60cm of approved make confirming to IS 13755 laid on 20mm thick bed of cement morter (1:4) with neat cement slurry jointing with white cement including cost, convenyance, royalty of all materials, labour charges, T&Petc. required for the workcomplete as per specificatoin and direction of the Engineer-in charge. |
| 225 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 226 | GroundFloor |
| 227 | FirstFloor |
| 228 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 229 | GroundFloor |
| 230 | FirstFloor |
| 231 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 232 | GroundFloor |
| 233 | FirstFloor |
| 234 | Providing fitting Fixing8mm to 10 mm thickness Vitrified tiles in dados & skirtingof size of 60cm X 60cm of approved make on 12 mm thick cement morter (1:3) with neat cement slurry jointing with white cement including cost, convenyance, royalty of all materials, labour charges, T&Petc. required for the workcomplete as per specificatoin and direction of the Engineer-in-charge. |
| 235 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 236 | GroundFloor |
| 237 | FirstFloor |
| 238 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 239 | GroundFloor |
| 240 | FirstFloor |
| 241 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 242 | GroundFloor |
| 243 | FirstFloor |
| 244 | Providing fitting Fixing 8mm to 10 mm thicknessVitrified tilesinfloors, kitchen, outersteps of size of 60cm X 60cm of approved make confirming to IS 13755 laid on 20mm thick bed of cement morter (1:4) with neat cement slurry jointing with white cement including cost, convenyance, royalty of all materials, labour charges, T&Petc. required for the workcomplete as per specificatoin and direction of the Engineer-in charge. |
| 245 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 246 | GroundFloor |
| 247 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 248 | GroundFloor |
| 249 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 250 | GroundFloor |
| 251 | Providing fitting Fixing 8mm to 10 mm thicknessVitrified tilesin staircase floors, kitchen, landing of size of 60cm X 60cm of approved make confirming to IS 13755 laid on 20mm thick bed of cement morter (1:4) with neat cement slurry jointing with white cement including cost, convenyance, royalty of all materials, labour charges, T&Petc. required for the workcomplete as per specificatoin and direction of the Engineer-in charge. |
| 252 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 253 | GroundFloor |
| 254 | FirstFloor |
| 255 | TerraceFloor |
| 256 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 257 | GroundFloor |
| 258 | FirstFloor |
| 259 | TerraceFloor |
| 260 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 261 | GroundFloor |
| 262 | FirstFloor |
| 263 | TerraceFloor |
| 264 | Providing fitting Fixing 8mm to 10 mm thickness Industrial Vitrified tilesin ramp of size of 30cm X 30cm of approved make confirming to IS 13755 laid on 20mm thick bed of cement morter (1:4) with neat cement slurry jointing with white cement including cost, convenyance, royalty of all materials, labour charges, T&Petc. required for the workcomplete as per specificatoin and direction of the Engineer-in charge. |
| 265 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 266 | Ramp |
| 267 | Kitchen |
| 268 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 269 | Ramp |
| 270 | Kitchen |
| 271 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 272 | Ramp |
| 273 | Kitchen |
| 274 | Providing average 25mm thick grading concrete (1:2:2) with portland slag cement (IS:455) and 6mm down H.G. aggregate using 2% water proofing cement compound of approved quality after applying two coats of polymer plaster as per approved specification over top of roof terrace including scraping and cleaning the roof surface, laying, plastering and finishing smooth to proper slope and gradient as per direction of the Engineer-in-charge including cost of all materials, conveyance and royalties, scaffolding, watering and curing, all labour, sundries and T&P etc complete as per direction of the Engineer-in-charge as per approved specification. |
| 275 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 276 | GroundFloor |
| 277 | Head Room |
| 278 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 279 | GroundFloor |
| 280 | Head Room |
| 281 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 282 | GroundFloor |
| 283 | Head Room |
| 284 | Supplying,fitting and fixing of M.S. window grill & iron grill gate made out of (35x35x5)mmsize angular frame with square bar M.S. flat for grills of approved design includingcost, conveyance,royalty of all materials, labour charges T&P etc. required for the work complete including iron fittingsas per the specification and direction of the Engineer-in-charge. |
| 285 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 286 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 287 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 288 | Painting two coats over a coat of priming to new wood andiron work using approved quality of Enamel paint and Red oxide primer including sand papering & polishing the surface with cost, conveyance, royaltyof all materials, labour charges, T&P etc. required for the work complete in all respect as per the specification and direction of the Engineer-in-charge. |
| 289 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 290 | GroundFloor |
| 291 | FirstFloor |
| 292 | TerraceFloor |
| 293 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 294 | GroundFloor |
| 295 | FirstFloor |
| 296 | TerraceFloor |
| 297 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 298 | GroundFloor |
| 299 | FirstFloor |
| 300 | TerraceFloor |
| 301 | Supplying, fitting and fixing of Stainless steel of 304 grade in hand railing of ramp, in the walls of toilet for sick personnelusing 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm @ 0.90mtr. C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc with cost, conveyance of all materials, cost of all labour, T&P etc. required for the complete in all respect as per direction of the Engineer-in-charge. |
| 302 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 303 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 304 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 305 | Aerated Autoclaved Fly ash (AAC) blocks ofdifferent sizes haing compressive strength not less than 4N/mm2 conforming to IS:2185 (Part - 3) - 2005 and IS:6441-1972including cost of all materials, labours, Conveyance, T&P etc all complete as per the direction of Engineer-In-Charge. |
| 306 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 307 | GroundFloor |
| 308 | FirstFloor |
| 309 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 310 | GroundFloor |
| 311 | FirstFloor |
| 312 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 313 | GroundFloor |
| 314 | FirstFloor |
| 315 | Supplying, fitting & fixing of Granite Tiles of minimum Above 0.40 sqm. (20mm thick) of approved make in floors laid on 20 mm thick cement mortar (1:4)(1 cement : 4 course sand) and filling joints with slurry including cost of all materials, labour T&P etc. required for the work all complete incl. rubbing as per direction of the Engineer-in-charge |
| 316 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 317 | GroundFloor |
| 318 | FirstFloor |
| 319 | Terrace Floor |
| 320 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 321 | GroundFloor |
| 322 | FirstFloor |
| 323 | Terrace Floor |
| 324 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 325 | GroundFloor |
| 326 | FirstFloor |
| 327 | Terrace Floor |
| 328 | Providing and fixing of Hollow metal door at all levels from ISO 9001-2008 certified Manufacturer OEM( Navir or Unistar/ Mediunited/ Tata Pravesh Jindal/NCL or equivallent ). All hollow metal general purpose doors with or without vision panel. Pressed Galvanised steel Single /Double leaf of required sizes consisting of frame, shutter, infill and finish as detailed below and conforming to IS 277. All doors & frames should be finished with Thermosetting weather proof Powder Coating in desired RAL Shades. Approved manufacturerwhich should be ISO & CE Certified & IGBC registered company. Rate should include supply and installation of door and hardware set as mentioned in the door and hardware schedule. Door frame shall be Single rebate profile of size 100 x 50 mm made out of 1.20mm thick galvanised steel sheet (18 gauge). Frames should be butt jointed and field assembled with self tabs. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Door leaf should be 44mm thick fully flush double skin door with or without vision lite. Door leaf shall be manufactured from 0.8mm (22 guage) minimum thick galvanised steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate Hardwares. The infill material shall be Rookwool insulation. All doors NSD 12044 should be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be as per joinery details with a screw on glass beeding on the inside. The glass should be 5mm tk clear Float glass. Hardwares should include the following:4 nos Hinges on each leaf1 no Door closer on each leaf, sliding door bolt and 1 no Mortice Dead lock1 Set D-type pull handle back to back on each leaf1 no Concealed flush bolt in inactive leaf of Double door, if any1 no vision glass on each leafFastners as required.The rate includes design supply, installation, testing, commissioning , transportation, T&P complete in all respect as per direction of EIC. |
| 329 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 330 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 331 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 332 | Supply and fixing of pre-painted NCL / Tata / Jindal or equivalant make Seccolor Louvered Ventilators made of pre.- painted steel (base steel as per IS 513 of -0.58 mm thick \"D\" quality, galvanized as per IS 277 with zinc of 120 GSM) primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer, section for outer frame of 33 x 57 mm Box Section for mullion 33 x 57 mm, and section for beading should be 12 x 25 mm with 4 mm pinhead glass for ventilators with Ethyl propylene Damien monomer Gasket (EPDM) and the sections cut to length mitre joined with corner bracket centre mullions fixed using mullion cap and with handle made of high grade aluminium powder coated and nylon receiver, corner bracketsmade of CRCA with Zinc Phosphate, Mullion caps made of glass filled nylon, frames fixed to the concrete /masonry wall by means of self expanding screws complete for finished item of work. |
| 333 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 334 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 335 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 336 | ProvidingandFixingWINSPIRE /Kommerling /Fenesta or equivalent make SlidingSystemsWindowsfabricatedfromRollformed.sections made of galvanized Steel colour coated/powder coated (Base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 GM/Sq.mtr) with total coated thickness of 0.58mm with Coated sections should be with Primer coat of epoxy primer of 5-7 microns thick, finish painted with Polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns, OR powder coated with pure polyester powder up to 50-60 microns thick and Section for Outer frame 2 Track should be of 59x44mm, Section for shutter should be of 35X49 for window. Section for Euro Groove should be 25x24 and for Lap Strip should be 30x41.Corner brackets made of glass filled nylon/CRCA with zinc phosphating.Gasket made of Ethyl.Propylene Diamine Monomer (EPDM). Locking system should be of single pin locking for Windows. Single Wheel Rollers for Windows should be provided.Glass shutter should be provided with a Glass of 5mm.The frame & shutter Sections Should be cut to length, joined with Corner Brackets made of.nylon/CRCA. Ethyl Propylene Diamine Monomer (EPDM) Gasket Should be used all around glass. Windows Frame should be fixed to brick/concrete masonry by using Nylon self- Expanding sleeves and diving MS electroplated 80mm long screws into sleeves through the frames. |
| 337 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 338 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 339 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 340 | Providing and Fixing NCL/ Jindal Seccolor Structural Glazing fabricated from Roll.formed sections made of Pre-painted Steel / Powder coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 Gm/Sqm) with total coated thickness of 0.72mm. The glass holding section made of 304 grade stainless steel of 0.58mm thick. Galvanized steel sections are to be sued as stiffeners inside the colour coated steel/powder coated sections as per the design requirement. Design calculations are made of suit wind pressures as given in IS 875. Primer coat with epoxy primer of 5 – 7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick. The vertical section should be of 50mm x100mm x 0.72mm, 33mm x 58mm x 0.72mmfor frame horizontal section, stiffener section should be 48mm x 98mm x 1mm, cover profiles sections should be of 20mm x 58mm x 0.58mm, Glass holding section should be of 37mm x 37mm & 37mm x 18mm.Brackets made of CRCA powder coated/Electroplated should be used to connect vertical to horizontal, vertical to slab, to fix verticals at top & bottom as per site requirement. Gasket madeof Ethyl Propylene Diamine Monomer. Natural cure, with Good U.V. Resistance Silicon to be used. Wall fixing of sections to concrete/masonry.wall should be with self-expanding cap & screws. |
| 341 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 342 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 343 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 344 | Providing , fitting & fixing of 34mm thick flush door shutter with 32mm thick BWR block board of Century / Greenply/Sylvan or equivalent make make and pasting 1 mm thick laminate with anti-bacterial property of Green Lam/ Century to be pasted with adhesive including fitting & fixing of all fixtures like SS heavy duty Aldrop,Hydraulic door clousure, SS heavy duty Tower bolt ,Vision panel , SS Door stopper,SSShape Handle etc ( Make: Dorma)of approved make including cost of all materials, all labour, all T&P etc. required for the work complete in all respect as per the direction of the Engineer-in-Charge |
| 345 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 346 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 347 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 348 | Providing \"RAJSHRI/Armstrong/Alstonoe equivalent Brandfactory made 100% Solid WPC (Wood Polymer Composite) Door Frame 125 mm x 65 mm Single Rebated, made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K Value 57-60 ( Suspension Grade 1 Calcium Carbonate Per Run. and Natural Fibers (Wood Powder/ Rice Husk/ Wheat Husk ) and Nontoxic additives fabricated with Ft. mater joints after applying PVC solvent Cement & screwed with full body treaded star headed screws having minimum frame density of 780 kg/ chin & manufactured by \"RAJSHRI\" an ISO 9001-2015 Certified Company, having good screw holding capacity (Screw Withdrawal strength of (Min 990 N) Minimum Compressive Strength of 58 N/mm2. Modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof, water/Moisture Proof & Fire retardant & Fixed in position with $5 Dash Fasteners/Hold Fast of required dia and length. all as per specifications drawings as directed by the Engineer-In-Charge. Material test certificate and authentication should be compulsory provided by the manufacturing company (Hold Fast or Dash Fasters shall be paid separately) |
| 349 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 350 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 351 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 352 | SITC of Sunken floor treatment stage1:Cleaning of concrete surface to remove dust,oil,grease including removal of laitance and cleaning with compressed air.Repairing surface irregularities,damaged concrete,if any,with Sika Latest modified repair mortar including a coat of bonding agent.stage2:supply and application of 1:3 cement-sand mortar,mixed with sika top 77-the polymer modified high quality emulsion,as a coving at the corners of floor and the vertical surface in the sunken area,and between floor and walls in the remaining area. Stage3:Supply and application ofSika Top Seal 107-the cementitious,flexible waterproof coating onto the prepared surface in a continuous film on the floor of the sunken area,taking the coating over the vertical surfaces on the floor and over the coving on to the wall (before tilling) to at least 300mm above the final finished floor level.The coating shall also be continued on to the inner surfaces of the pipe penetration holes .Two coats shall be applied. Few parameters:Chemical Base Part A:liquid polymer and additive Part B:portland cementwith selected aggregate and additive,Density fresh slurry density~2.00kg/I at +270C,Layer Thicknes 1.5mm -2.00 average,water Vapour Resistance 3g/m2/day.Mechanical/Physical properties 3 days~2N/mm2,28 days~20N/mm2.Compressive Strength Above values at +270C,tensile Strength~4.56N/mm2 after 14 days exposure(According to ASTM D 2370),Bond Strength 2.0N/mm2 at +270C (failure in substrate),Elongation at Break With sika@ Fab-1,8-10% |
| 353 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 354 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 355 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 356 | Providing and fixing Series casement door fabricated from roll formed sections made of Galvanized Steel Colour Coated/Powder Coated (Base Steel as per IS 513 “D” quality, Galvanized as per IS 277 with Zinc of 120 grams/Sq. Mtr.) with total coated thickness of 0.58 mm.Coated Sections should be with Primer Coat of Epoxy Primer of 5-7 microns thick, finish painted with Polyester Paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns, or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Frame and Shutter Frame Sections should be cut to length and mitre joined with Polypropylene Corner Brackets. Mullion Section should be joined with Frame/Mullion using Nylon Mullion Cap. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter.Section for frame should be 48mm x 50mm, Section for Mullion should be of 48mm x 50mm, Section for Glazed Shutter Frame should be of 47mm x 20mm,and Section for Fixed Glass Bead should be of 12mm x 12mm.Each Glazed Shutter should be provided with S.S. Pivot Hinges-1set, Seccolor Handle & Seccolor Stay.Glazed Shutter and Fixed Glass portions should be provided with a glass of 8mm Plain toughened Float Glass. The work is inclusive all materials, labour, T&P, scaffolding, transportation etc complete as per direction of EIC. Make NCL/Tata/Jindal or equivalent |
| 357 | 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 358 | 2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 359 | 3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 360 | E.I. works of Construction of 300 CapacityMulti Purpose Hall-1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 361 | Recessed wiring to light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5 Amp,one way modularswitch ISI marked and ceiling rose ISI marked mounted on Modular G.I. box having front bakelite cover of suitable size , MS box with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire = Finollex / L & T/ Anchor/ Havels/ V-Guard/ Greatwhite / Polycab)Light point Group A (1.1.1) |
| 362 | -do- .... Light point Group B (1.1.2) |
| 363 | -do- ....Light point Group C (1.1.3) |
| 364 | S/F of 5A. Modular Switch & 5A. Modular Socket outlet of ISI marked on existing board (1.25.1+1.25.4) |
| 365 | S/F of extension board of 4 modular Metal box with modular base & cover in recess including providing and fixing of 3pin 5/6amp modular socket out let &5/6 amp piano type modular switch, connection, painting etc as required. (1.26) |
| 366 | S/F of Power point with 4 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piano type Modular switch & Socket, connection, painting etc as required (1.2.7) |
| 367 | S/F of 12 Modular GI boxin recess with suitable size of Modular base cover in front including providing and fixing2 nos 3 pin 5/6 amp. Modular Socket out let & 5/6amp. Modular type switch with 1no 5 pin 15/16 amp. Modular Socket out let & 15/16amp. Modular type switch,connection,painting etc. as required (1.25.1+1.25.4) |
| 368 | Wiring for circuit I sub main wiring alongwith earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS- 694/1990 in 20mm dia non metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required( Make of wire- Finolex/ / Anchor/ Havels/ V-guard / HPL / L&T / Gratewhite / Polycab). -do- 2x1.5sqmm +1x1.5sqmm ( 1.8.1 ) (LDB to LSB/LIGHT CKT) |
| 369 | -do-2x2.5sqmm +1x1.5sqmm ( 1.8.2 ) (BDB to LSB/LIGHT CKT/5A PLUG/INVERTER POINT TO EACH QTR) |
| 370 | -do-4x2.5sqmm +2x2.5sqmm ( 1.8.8 )(PDB to PSB) |
| 371 | -do- 2x4sqmm +1x1.5sqmm ( 1.8.3 )(PDB to PSB) |
| 372 | -do- 4x4sqmm +2x2.5sqmm ( 1.8.9 ) (PDB to PSB) |
| 373 | -do- 2x6sqmm +1x2.5sqmm ( 1.8.4 ) (LFDB TO LBDB) |
| 374 | -do- 4x6sqmm +2x2.5sqmm ( 1.8.10 ) |
| 375 | -do- 4x10sqmm + 2x4.0sqmm ( 1.8.11 ) |
| 376 | Supplying and fixing 20 amps, 240 volts, SPN, industrial type socket outlet, with 2 pole and earth metal enclosed plug top along with 32 amps. C-series, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, and complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge ( Make-Havells/C & S/Legrand) |
| 377 | S/F of 18 SWG Modular metal box of following sizes (Nominal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required.2 Modular box with base & cover (1.24.2) |
| 378 | 4 Modular box with base & cover (1.24.3) |
| 379 | 8 Modular box with base & cover (1.24.5) |
| 380 | 12 Modular box with base & cover (1.24.6) |
| 381 | S/F of 25AMoter Starter switch for A.C (Make: Havells / Anchor/Le-Grand) |
| 382 | S/F of Call bell/ Buzzer ISI marked sutiable for DC/AC single Phase 230 volts complete as required.(1.30) |
| 383 | S/F of batten holder BK angle holder ISI marked including connection etc instead of ceiling rose (Make: Cona / Anchor / Havells / Greatwhite / Preeti / HPL)(1.29-1.28) |
| 384 | Supply, Installation,Testing and Commissioning of Exhaust fan of 225mm sweep in the existing opening,including making the hole to suit the size of the above fan making good thedamaged complete, connection, etc as required. (Make- USHA/ Orient / Almonard) |
| 385 | Supplying, installation, of exhaust fan of heavy duty 380 mm sweep 1400 rpm with louvers Make-Equievalant higher model with 5 star ratedof Havells/almonard/Anchor/Panasonic/Usha/Bajajor equievalant reputed make & model A catagory ISI marked as approved ) of exhaust fan in the existing wall, including fixing & conntection .as required as per direction of Engg.-in-Charge. |
| 386 | Supply & Fixing of 48\" A.C. ceiling fan without regulator incudig numbering of reputed mark including all connections(Make:Usha-Striker Millenium / Crompton-Jura / Havells-Velopcity/ Spark/ Anchor-XL/ Orient-Summer Pride ) |
| 387 | S/F of Modular electric step ceiling fan regulater in existing switchboxincluding connection with 1.5sqmm FR PVC insulated single core multistrand copper conductor earthing the regulatoras required.(1.38) |
| 388 | S/F of 18-20 wattLED Surface ceiling light fitting compoete with all connection.\ including fixing and all accessories as per directionof Engineer-In-charge(Make: Havels / Phillps / Crompton / Polycab /Orient) |
| 389 | S/F of 18-25 wattLED Tube light fitting compoete with all connection.\ including fixing and all accessories as per directionof Engineer-In-charge(Make: Havels / Phillps / Crompton / Polycab /HPL) |
| 390 | SITC of Sleek LED 10 watt mirror light fitting with extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge.( Make :Philips/Bajaj/Lightting Technologyor equievalant reputed make & model A catagory ISI marked as approved. ) |
| 391 | S/F of 45-48 wattLED street light fitting complete with all connection.\ including fixing of bracket and all accessories as per directionof Engineer-In-charge(Make: Havels / Phillps / Crompton / Polycab /HPL) |
| 392 | S/F of Extra downrod 20mm dia (20 cm) (1.41) |
| 393 | S/F of 4way (4+12) TPN Double Door and neutral sheet steel MCB DISTRIBUTION BOARD 250v on surface /recess complete with tinned copper bus bar, neutral bar, earth bar, din bar ,detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (except MCB) 2.5.5 (FOR LIGHT,POWER INDOOR,3-PH,POWER LOAD) |
| 394 | S/F of 2+4 way MCB DISTRIBUTION BOARD 250v on surface /recess complete with tinned copper bus bar, neutral bar, earth bar, din bar ,detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (except MCB) 2.4.1 (only each EM. CONNECTION UPS LOAD) |
| 395 | S/Fof \"B\" series DP MCB of 5A to 32 Amp rating 240Volt \"B\" series MCB for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP)(2.6.2) |
| 396 | S/Fof \"B\" series SP MCB of 5A to 32 Amp rating 240Volt \"B\" series MCB for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP)(2.6.1) |
| 397 | Supplying and fixing 40 Amps rating, TPN, 415 volts, RCCB,300mAin the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge (Make : L&T / Legrand / C&S) |
| 398 | Supplying and fixing 25Amps DP 240 volts, RCCB,300mAin the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge (Make : L&T / Legrand / C&S) |
| 399 | Supplying and fixing 63Amps TPN 415 volts, RCCB,300mA in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge (Make : L&T / Legrand / C&S) |
| 400 | Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick and 25mm x 5mm copper tape (1.15Kg. Per Mtr.) 3.5Mtr. & 20mm G.I.pipe medium class 2.7 Mtr. ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc wih charcoal and salt as required. (3.5 + 3.6) |
| 401 | Providing and fixing 8 SWG copper wire in recess for loop earthing as required. (3.18) |
| 402 | Providing and fixing 25mm x 5 mm copper strip on surface or in recess for connections etc. as required (3.15) |
| 403 | Supply of 2.5mmsq 3 Corealluminium armoured cable (for small power,street light) |
| 404 | S/F of 35mmsq 3½ Corealluminium armoured cable (Make: Nico/ Polycab/ Glostar / Havells) |
| 405 | Laying of 35mmsq 3½ Core cable in ground |
| 406 | Supplying and making end termination with brass compression gland and aluminum lugs for 35mmsq 3½ Core cable (5.8.21) |
| 407 | Supply, instaliatiion,Testing and commissioning of 125A, TPN panel board made of 16 SWG with provision of Incoming:- (a) 125A 4Pole MCCB 1No., (b) 125Amp 4P Change over -1No.(c) Copper bus-bar (25mm x 5mm copper flat) -1 Set., Out going:- (a) 63A 4P MCB -2Nos., (b) 32A 4P MCB -2Nos., Instrument:-(i) 01 Set of 0-100Amps MFM & CTS (DIGITAL) , 3Nos. LED phase indicator and danger plate (Make: Legrand / L&T / Havells / C&S) |
| 408 | E.I. works of Construction of 300 CapacityMulti Purpose Hall-2) Mz-Badagada(NearBadagadaBrit Colony Chari Chhak) (300) |
| 409 | Recessed wiring to light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5 Amp,one way modularswitch ISI marked and ceiling rose ISI marked mounted on Modular G.I. box having front bakelite cover of suitable size , MS box with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire = Finollex / L & T/ Anchor/ Havels/ V-Guard/ Greatwhite / Polycab)Light point Group A (1.1.1) |
| 410 | -do- .... Light point Group B (1.1.2) |
| 411 | -do- ....Light point Group C (1.1.3) |
| 412 | S/F of 5A. Modular Switch & 5A. Modular Socket outlet of ISI marked on existing board (1.25.1+1.25.4) |
| 413 | S/F of extension board of 4 modular Metal box with modular base & cover in recess including providing and fixing of 3pin 5/6amp modular socket out let &5/6 amp piano type modular switch, connection, painting etc as required. (1.26) |
| 414 | S/F of Power point with 4 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piano type Modular switch & Socket, connection, painting etc as required (1.2.7) |
| 415 | S/F of 12 Modular GI boxin recess with suitable size of Modular base cover in front including providing and fixing2 nos 3 pin 5/6 amp. Modular Socket out let & 5/6amp. Modular type switch with 1no 5 pin 15/16 amp. Modular Socket out let & 15/16amp. Modular type switch,connection,painting etc. as required (1.25.1+1.25.4) |
| 416 | Wiring for circuit I sub main wiring alongwith earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS- 694/1990 in 20mm dia non metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required( Make of wire- Finolex/ / Anchor/ Havels/ V-guard / HPL / L&T / Gratewhite / Polycab). -do- 2x1.5sqmm +1x1.5sqmm ( 1.8.1 ) (LDB to LSB/LIGHT CKT) |
| 417 | -do-2x2.5sqmm +1x1.5sqmm ( 1.8.2 ) (BDB to LSB/LIGHT CKT/5A PLUG/INVERTER POINT TO EACH QTR) |
| 418 | -do-4x2.5sqmm +2x2.5sqmm ( 1.8.8 )(PDB to PSB) |
| 419 | -do- 2x4sqmm +1x1.5sqmm ( 1.8.3 )(PDB to PSB) |
| 420 | -do- 4x4sqmm +2x2.5sqmm ( 1.8.9 ) (PDB to PSB) |
| 421 | -do- 2x6sqmm +1x2.5sqmm ( 1.8.4 ) (LFDB TO LBDB) |
| 422 | -do- 4x6sqmm +2x2.5sqmm ( 1.8.10 ) |
| 423 | -do- 4x10sqmm + 2x4.0sqmm ( 1.8.11 ) |
| 424 | Supplying and fixing 20 amps, 240 volts, SPN, industrial type socket outlet, with 2 pole and earth metal enclosed plug top along with 32 amps. C-series, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, and complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge ( Make-Havells/C & S/Legrand) |
| 425 | S/F of 18 SWG Modular metal box of following sizes (Nominal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required.2 Modular box with base & cover (1.24.2) |
| 426 | 4 Modular box with base & cover (1.24.3) |
| 427 | 8 Modular box with base & cover (1.24.5) |
| 428 | 12 Modular box with base & cover (1.24.6) |
| 429 | S/F of 25AMoter Starter switch for A.C (Make: Havells / Anchor/Le-Grand) |
| 430 | S/F of Call bell/ Buzzer ISI marked sutiable for DC/AC single Phase 230 volts complete as required.(1.30) |
| 431 | S/F of batten holder BK angle holder ISI marked including connection etc instead of ceiling rose (Make: Cona / Anchor / Havells / Greatwhite / Preeti / HPL)(1.29-1.28) |
| 432 | Supply, Installation,Testing and Commissioning of Exhaust fan of 225mm sweep in the existing opening,including making the hole to suit the size of the above fan making good thedamaged complete, connection, etc as required. (Make- USHA/ Orient / Almonard) |
| 433 | Supplying, installation, of exhaust fan of heavy duty 380 mm sweep 1400 rpm with louvers Make-Equievalant higher model with 5 star ratedof Havells/almonard/Anchor/Panasonic/Usha/Bajajor equievalant reputed make & model A catagory ISI marked as approved ) of exhaust fan in the existing wall, including fixing & conntection .as required as per direction of Engg.-in-Charge. |
| 434 | Supply & Fixing of 48\" A.C. ceiling fan without regulator incudig numbering of reputed mark including all connections(Make:Usha-Striker Millenium / Crompton-Jura / Havells-Velopcity/ Spark/ Anchor-XL/ Orient-Summer Pride ) |
| 435 | S/F of Modular electric step ceiling fan regulater in existing switchboxincluding connection with 1.5sqmm FR PVC insulated single core multistrand copper conductor earthing the regulatoras required.(1.38) |
| 436 | S/F of 18-20 wattLED Surface ceiling light fitting compoete with all connection.\ including fixing and all accessories as per directionof Engineer-In-charge(Make: Havels / Phillps / Crompton / Polycab /Orient) |
| 437 | S/F of 18-25 wattLED Tube light fitting compoete with all connection.\ including fixing and all accessories as per directionof Engineer-In-charge(Make: Havels / Phillps / Crompton / Polycab /HPL) |
| 438 | SITC of Sleek LED 10 watt mirror light fitting with extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge.( Make :Philips/Bajaj/Lightting Technologyor equievalant reputed make & model A catagory ISI marked as approved. ) |
| 439 | S/F of 45-48 wattLED street light fitting complete with all connection.\ including fixing of bracket and all accessories as per directionof Engineer-In-charge(Make: Havels / Phillps / Crompton / Polycab /HPL) |
| 440 | S/F of Extra downrod 20mm dia (20 cm) (1.41) |
| 441 | S/F of 4way (4+12) TPN Double Door and neutral sheet steel MCB DISTRIBUTION BOARD 250v on surface /recess complete with tinned copper bus bar, neutral bar, earth bar, din bar ,detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (except MCB) 2.5.5 (FOR LIGHT,POWER INDOOR,3-PH,POWER LOAD) |
| 442 | S/F of 2+4 way MCB DISTRIBUTION BOARD 250v on surface /recess complete with tinned copper bus bar, neutral bar, earth bar, din bar ,detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (except MCB) 2.4.1 (only each EM. CONNECTION UPS LOAD) |
| 443 | S/Fof \"B\" series DP MCB of 5A to 32 Amp rating 240Volt \"B\" series MCB for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP)(2.6.2) |
| 444 | S/Fof \"B\" series SP MCB of 5A to 32 Amp rating 240Volt \"B\" series MCB for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP)(2.6.1) |
| 445 | Supplying and fixing 40 Amps rating, TPN, 415 volts, RCCB,300mAin the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge (Make : L&T / Legrand / C&S) |
| 446 | Supplying and fixing 25Amps DP 240 volts, RCCB,300mAin the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge (Make : L&T / Legrand / C&S) |
| 447 | Supplying and fixing 63Amps TPN 415 volts, RCCB,300mA in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge (Make : L&T / Legrand / C&S) |
| 448 | Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick and 25mm x 5mm copper tape (1.15Kg. Per Mtr.) 3.5Mtr. & 20mm G.I.pipe medium class 2.7 Mtr. ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc wih charcoal and salt as required. (3.5 + 3.6) |
| 449 | Providing and fixing 8 SWG copper wire in recess for loop earthing as required. (3.18) |
| 450 | Providing and fixing 25mm x 5 mm copper strip on surface or in recess for connections etc. as required (3.15) |
| 451 | Supply of 2.5mmsq 3 Corealluminium armoured cable (for small power,street light) |
| 452 | S/F of 35mmsq 3½ Corealluminium armoured cable (Make: Nico/ Polycab/ Glostar / Havells) |
| 453 | Laying of 35mmsq 3½ Core cable in ground |
| 454 | Supplying and making end termination with brass compression gland and aluminum lugs for 35mmsq 3½ Core cable (5.8.21) |
| 455 | Supply, instaliatiion,Testing and commissioning of 125A, TPN panel board made of 16 SWG with provision of Incoming:- (a) 125A 4Pole MCCB 1No., (b) 125Amp 4P Change over -1No.(c) Copper bus-bar (25mm x 5mm copper flat) -1 Set., Out going:- (a) 63A 4P MCB -2Nos., (b) 32A 4P MCB -2Nos., Instrument:-(i) 01 Set of 0-100Amps MFM & CTS (DIGITAL) , 3Nos. LED phase indicator and danger plate (Make: Legrand / L&T / Havells / C&S) |
| 456 | E.I. works of Construction of 300 CapacityMulti Purpose Hall-3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 457 | Recessed wiring to light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5 Amp,one way modularswitch ISI marked and ceiling rose ISI marked mounted on Modular G.I. box having front bakelite cover of suitable size , MS box with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire = Finollex / L & T/ Anchor/ Havels/ V-Guard/ Greatwhite / Polycab)Light point Group A (1.1.1) |
| 458 | -do- .... Light point Group B (1.1.2) |
| 459 | -do- ....Light point Group C (1.1.3) |
| 460 | S/F of 5A. Modular Switch & 5A. Modular Socket outlet of ISI marked on existing board (1.25.1+1.25.4) |
| 461 | S/F of extension board of 4 modular Metal box with modular base & cover in recess including providing and fixing of 3pin 5/6amp modular socket out let &5/6 amp piano type modular switch, connection, painting etc as required. (1.26) |
| 462 | S/F of Power point with 4 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piano type Modular switch & Socket, connection, painting etc as required (1.2.7) |
| 463 | S/F of 12 Modular GI boxin recess with suitable size of Modular base cover in front including providing and fixing2 nos 3 pin 5/6 amp. Modular Socket out let & 5/6amp. Modular type switch with 1no 5 pin 15/16 amp. Modular Socket out let & 15/16amp. Modular type switch,connection,painting etc. as required (1.25.1+1.25.4) |
| 464 | Wiring for circuit I sub main wiring alongwith earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS- 694/1990 in 20mm dia non metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required( Make of wire- Finolex/ / Anchor/ Havels/ V-guard / HPL / L&T / Gratewhite / Polycab). -do- 2x1.5sqmm +1x1.5sqmm ( 1.8.1 ) (LDB to LSB/LIGHT CKT) |
| 465 | -do-2x2.5sqmm +1x1.5sqmm ( 1.8.2 ) (BDB to LSB/LIGHT CKT/5A PLUG/INVERTER POINT TO EACH QTR) |
| 466 | -do-4x2.5sqmm +2x2.5sqmm ( 1.8.8 )(PDB to PSB) |
| 467 | -do- 2x4sqmm +1x1.5sqmm ( 1.8.3 )(PDB to PSB) |
| 468 | -do- 4x4sqmm +2x2.5sqmm ( 1.8.9 ) (PDB to PSB) |
| 469 | -do- 2x6sqmm +1x2.5sqmm ( 1.8.4 ) (LFDB TO LBDB) |
| 470 | -do- 4x6sqmm +2x2.5sqmm ( 1.8.10 ) |
| 471 | -do- 4x10sqmm + 2x4.0sqmm ( 1.8.11 ) |
| 472 | Supplying and fixing 20 amps, 240 volts, SPN, industrial type socket outlet, with 2 pole and earth metal enclosed plug top along with 32 amps. C-series, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, and complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge ( Make-Havells/C & S/Legrand) |
| 473 | S/F of 18 SWG Modular metal box of following sizes (Nominal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required.2 Modular box with base & cover (1.24.2) |
| 474 | 4 Modular box with base & cover (1.24.3) |
| 475 | 8 Modular box with base & cover (1.24.5) |
| 476 | 12 Modular box with base & cover (1.24.6) |
| 477 | S/F of 25AMoter Starter switch for A.C (Make: Havells / Anchor/Le-Grand) |
| 478 | S/F of Call bell/ Buzzer ISI marked sutiable for DC/AC single Phase 230 volts complete as required.(1.30) |
| 479 | S/F of batten holder BK angle holder ISI marked including connection etc instead of ceiling rose (Make: Cona / Anchor / Havells / Greatwhite / Preeti / HPL)(1.29-1.28) |
| 480 | Supply, Installation,Testing and Commissioning of Exhaust fan of 225mm sweep in the existing opening,including making the hole to suit the size of the above fan making good thedamaged complete, connection, etc as required. (Make- USHA/ Orient / Almonard) |
| 481 | Supplying, installation, of exhaust fan of heavy duty 380 mm sweep 1400 rpm with louvers Make-Equievalant higher model with 5 star ratedof Havells/almonard/Anchor/Panasonic/Usha/Bajajor equievalant reputed make & model A catagory ISI marked as approved ) of exhaust fan in the existing wall, including fixing & conntection .as required as per direction of Engg.-in-Charge. |
| 482 | Supply & Fixing of 48\" A.C. ceiling fan without regulator incudig numbering of reputed mark including all connections(Make:Usha-Striker Millenium / Crompton-Jura / Havells-Velopcity/ Spark/ Anchor-XL/ Orient-Summer Pride ) |
| 483 | S/F of Modular electric step ceiling fan regulater in existing switchboxincluding connection with 1.5sqmm FR PVC insulated single core multistrand copper conductor earthing the regulatoras required.(1.38) |
| 484 | S/F of 18-20 wattLED Surface ceiling light fitting compoete with all connection.\ including fixing and all accessories as per directionof Engineer-In-charge(Make: Havels / Phillps / Crompton / Polycab /Orient) |
| 485 | S/F of 18-25 wattLED Tube light fitting compoete with all connection.\ including fixing and all accessories as per directionof Engineer-In-charge(Make: Havels / Phillps / Crompton / Polycab /HPL) |
| 486 | SITC of Sleek LED 10 watt mirror light fitting with extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge.( Make :Philips/Bajaj/Lightting Technologyor equievalant reputed make & model A catagory ISI marked as approved. ) |
| 487 | S/F of 45-48 wattLED street light fitting complete with all connection.\ including fixing of bracket and all accessories as per directionof Engineer-In-charge(Make: Havels / Phillps / Crompton / Polycab /HPL) |
| 488 | S/F of Extra downrod 20mm dia (20 cm) (1.41) |
| 489 | S/F of 4way (4+12) TPN Double Door and neutral sheet steel MCB DISTRIBUTION BOARD 250v on surface /recess complete with tinned copper bus bar, neutral bar, earth bar, din bar ,detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (except MCB) 2.5.5 (FOR LIGHT,POWER INDOOR,3-PH,POWER LOAD) |
| 490 | S/F of 2+4 way MCB DISTRIBUTION BOARD 250v on surface /recess complete with tinned copper bus bar, neutral bar, earth bar, din bar ,detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (except MCB) 2.4.1 (only each EM. CONNECTION UPS LOAD) |
| 491 | S/Fof \"B\" series DP MCB of 5A to 32 Amp rating 240Volt \"B\" series MCB for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP)(2.6.2) |
| 492 | S/Fof \"B\" series SP MCB of 5A to 32 Amp rating 240Volt \"B\" series MCB for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP)(2.6.1) |
| 493 | Supplying and fixing 40 Amps rating, TPN, 415 volts, RCCB,300mAin the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge (Make : L&T / Legrand / C&S) |
| 494 | Supplying and fixing 25Amps DP 240 volts, RCCB,300mAin the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge (Make : L&T / Legrand / C&S) |
| 495 | Supplying and fixing 63Amps TPN 415 volts, RCCB,300mA in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge (Make : L&T / Legrand / C&S) |
| 496 | Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick and 25mm x 5mm copper tape (1.15Kg. Per Mtr.) 3.5Mtr. & 20mm G.I.pipe medium class 2.7 Mtr. ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc wih charcoal and salt as required. (3.5 + 3.6) |
| 497 | Providing and fixing 8 SWG copper wire in recess for loop earthing as required. (3.18) |
| 498 | Providing and fixing 25mm x 5 mm copper strip on surface or in recess for connections etc. as required (3.15) |
| 499 | Supply of 2.5mmsq 3 Corealluminium armoured cable (for small power,street light) |
| 500 | S/F of 35mmsq 3½ Corealluminium armoured cable (Make: Nico/ Polycab/ Glostar / Havells) |
| 501 | Laying of 35mmsq 3½ Core cable in ground |
| 502 | Supplying and making end termination with brass compression gland and aluminum lugs for 35mmsq 3½ Core cable (5.8.21) |
| 503 | Supply, instaliatiion,Testing and commissioning of 125A, TPN panel board made of 16 SWG with provision of Incoming:- (a) 125A 4Pole MCCB 1No., (b) 125Amp 4P Change over -1No.(c) Copper bus-bar (25mm x 5mm copper flat) -1 Set., Out going:- (a) 63A 4P MCB -2Nos., (b) 32A 4P MCB -2Nos., Instrument:-(i) 01 Set of 0-100Amps MFM & CTS (DIGITAL) , 3Nos. LED phase indicator and danger plate (Make: Legrand / L&T / Havells / C&S) |
| 504 | P.H. works of Construction of 300 Capacity Multi Purpose Hall- 1) Mz-Bhimpur (Near CDA Office Kargil Road, Palasapali) (300) |
| 505 | A- Internal PH Work |
| 506 | Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor C-PVC pipesconforming topipe fittings of the following nominal bore with clamps including making good the wall, ceilingand floor all complete as per specification and direction of the Engineer in charge |
| 507 | GroundFloor |
| 508 | 20mm dia C-PVC pipe (Ashirbad/Supreme) |
| 509 | 25mm dia C-PVC pipe (Ashirbad/Supreme) |
| 510 | In 1st Floor |
| 511 | 20mm dia C-PVC pipe (Ashirbad/Supreme) |
| 512 | 25mm dia C-PVC pipe (Ashirbad/Supreme) |
| 513 | 32mm dia C-PVC pipe (Ashirbad/Supreme) |
| 514 | In 2nd Floor |
| 515 | 40mm dia C-PVC pipe (Ashirbad/Supreme) |
| 516 | Supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking GI pipes and fittings/ PVC pipes and fittings etc all complete as per PH specification and direction of the Engineer in charge. |
| 517 | 250mmthick wall in Ground floor |
| 518 | In 1st Floor |
| 519 | Supplying all materials, labour, T&Pand cutting hole in R.C.C floors, roofs, etc upto 19 cm thickfor passing G.I. Pipes / P.V.C pipes and fittings etc and repairing the holes afterinsertion of pipes etc with cement concrete (1:2:4 ) including finishing complete so as to make it leak proof as per direction of theEngineer in charge. in Ground Floor |
| 520 | In 1st Floor |
| 521 | Supplying allmaterials, labour, T&P and cutting grooves in pucca floors and walls for takingGI/ PVC pipes and making good the damages as per the direction of the Engineer in charge. In Ground Floor |
| 522 | In 1st Floor |
| 523 | Supplying all materials, labour, T&P and cutting holes through existing brick or laterite masonry wall for taking PVC pipes and fittings including making good the damages etc all completeas per PH specification and direction of the Engineer in charge |
| 524 | 250mm to 375mmthick wall |
| 525 | in GroundFloor to Ist Floor |
| 526 | Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge |
| 527 | 15mm dia CP Long Body Bib cock (Jaquar) |
| 528 | 15mm dia CP angle stop cock(Jaquar) |
| 529 | 20mm dia CP consealed stop cock (Jaquar) |
| 530 | 15mm dia CP two in one bib cock (Jaquar) |
| 531 | 15mm dia CP Health faucet (Jaquar) |
| 532 | 15mm dia CP extension piece |
| 533 | 15mm dia CP Pillar cock (Jaquar) |
| 534 | 25mm dia G.M or Brass F.W valve (Sakti make) |
| 535 | 32mm dia PVC F.W valve |
| 536 | 40mm dia PVC F.W valve |
| 537 | 125mm dia CP gratings |
| 538 | 15mm dia CP revolving shower (Jaquar make) |
| 539 | 15mm dia CP Auto closing Urinal Flush Valve (PRS-CHR-077 Jaquar make) |
| 540 | Supplying all materials, labour, T&P and fitting and fixing 10 litres capacity low level flushing cistern with a pair of cast iron or M.S brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle, unions and couplings for connection with inlet, outlet and overflow pipes,32mm dia CP flush bend,15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting the inlet pipe with supply main etc all complete as per specification and direction of the Engineer in charge |
| 541 | 10 litres PVC L.L. Cistern (Slimline-white) |
| 542 | Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricantby non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge |
| 543 | 75mm dia U-PVC SWR pipes(Supreme/Ashirvad) |
| 544 | 75mm U-PVC plain bend |
| 545 | 110mm dia U-PVC SWR pipes(Supreme/Ashirvad) |
| 546 | 110mm U-PVC door bend |
| 547 | 110mm U-PVC door Tee |
| 548 | 110mm U-PVC plain Tee |
| 549 | 110mm dia U-PVC offset without ear |
| 550 | 110mm U-PVC plain bend |
| 551 | 110mm U-PVC vent cowl |
| 552 | 110mm dia U-PVC \"P\" trap |
| 553 | 110mm dia U-PVC socket plain |
| 554 | 75mm dia U-PVC socket plain |
| 555 | PVC Clamp |
| 556 | 110mm U-PVC door cross Tee |
| 557 | Supplying all materials, labour T&Pand fixing water closet, (Orissa pattern squating pan) duly embeded in c.c. (1:5:10) using 4cm h.g. metal all complete as per direction of E.I.C.--(583x440)mm Orissa pan (Neycer/Cerra/ Parry ware/ Hindware) |
| 558 | 580mm size Orissa pan(Hindware/Parryware/Neycer) |
| 559 | Supplying all materials, labour, T&P and fixing bowl pattern urinal including connecting the urinal with waste pipe by means of white lead mixed with chopped hemp etc all complete as per specification and direction of the Engineer in charge. |
| 560 | Halfstall wall Urinal (Parryware/Hindware/Neycer) |
| 561 | 15mm dia Urinal spreder |
| 562 | 32mm dia Dome waste |
| 563 | Supplying all materials, labour, T&P and fixing Wash Down Water Closet (European type W.C pan) with integral ‘S’ or ‘P’ trap to the floor with wooden plug and chromium plated screws including jointing the trap with soil pipe in cement mortar (1:1) etc all complete as per specification and direction of the Engineer in charge. |
| 564 | E.W.C. with seat cover (Parryware/Hindware/Neycer) |
| 565 | Supplying all materials, labour, T&P fitting and fixing Plastic Seat and cover for E.W.C. with chromium plated brass hinges and rubber buffers all complete as perr specification and direction of E.I.C. (Neycer/ Cerra/Parry ware/ Hindware) |
| 566 | EWC (Matrix set) Hindware No.70002(P-18)(WHB 65 x 35 with one pair mounting brackets, EWC & Cistern complete with fittings & seat cover, one no hinged rail 76 cm and five nos of grab rails 60 cm) |
| 567 | Supplying all materials, labour T&P and fixing wash basins with hole for pillar taps with C.I/M.S brackets painted white including holes in walls and making good the damages etc. all complete as per P.H specification and direction of E.I.C.-- 550mm x 400mm WHB with all Fittings with C.P. Waste, PVC Waste Pipe & Connection Pipe. (Neycer/Cerra/ Parry ware/ Hindware) |
| 568 | Supplying all materials, labour T&P and fixing padestrial for wash basin complete recessed at the back for the reception of pipe and fitting etc. all complete as per specification and direction of E.I.C. (Neycer/Parrywear/Cerra/Hindware) |
| 569 | Under Counterbasin(560x450)Hindware-No.10095 |
| 570 | Supplying all materials, labour, T&P and fixing mirror of superior glass conforming to IS:3438-1996 mounted on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification an direction of the Engineer in charge |
| 571 | 600mm x 450mm size B.E mirror |
| 572 | Large size mirror with frame |
| 573 | 2 x 3.00 xx0.90= |
| 574 | Supplying all materials, labour, T&P and fixing standard sized glass-shelf with CP brass brackets and guard rails complete fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge |
| 575 | 600 x 125mm plate glass shelf with CP guard rails (Plaza/Amber/Aquatic) |
| 576 | Supplying all materials, labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge |
| 577 | 25mm x 600mm long CP towel rail (Plaza/Amber/Aquatic) |
| 578 | CP towel Ring (Plaza/Amber/Aquatic) |
| 579 | Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge |
| 580 | CP soap holder(Plaza/Amber/Aquatic) |
| 581 | Supplying all materials, labour, T&P and fixing wash kitchen sink/laboratory sink with outlet at end and weir overflow including fitting and fixing a pair of cast iron or MS brackets painted white, fixing 50mm/40mm dia CP brass waste, fixing 50mm/40mm dia PVC waste pipe 910mm long with supply of wooden plugs, screws and cement etc including cutting holes in walls and making good the damages etc all complete as per specification and direction of the Engineer in charge |
| 582 | 550 x 450 x 200mm size S/S kitchen sink (Jayana make ) |
| 583 | Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including cement punning,watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 584 | In Ist Floor |
| 585 | Providing and laying Sika top seal 109 hi over roof top slab and parapet ,toilet inside after cleaning of surface and applied with a coat of Sika 109 hi primer as per approved specification.The Sika shall be laid between two coats of water proofing membrance and the entire application cover with Sika top seak hi curing,compoundof all materials and cost of labour T&P etc.complete as per the direction of the Engineer-in-charge. |
| 586 | In Ist Floor |
| 587 | Supplying all materials labour T&P and filling in foundation and plinth with sandwellwatered and rammed including conveyance of all materials to work sitepayment of royalty taxes etc all complete as per direction ofEngineer in charge In ground floor |
| 588 | In 1st Floor |
| 589 | Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard granite chips broken including watering, curing, conveyance of all materials to worksite, payment of royality, taxes etc all complete as aper specification and direction of the E.I.C. -In Ground Floor |
| 590 | In 1st Floor |
| 591 | Supplying all materials, labour, T&P and constructing Gully Trap chamber of the following inside size with 8cm thick R.C.C precast cover slab in cement concrete (1:2:4) mix using 12mm size h.g chips, foundation concrete (1:4:8) using 40mm size hard granite metal on bed and around trap, Fly ash brickwork in c.m (1:6) in F&P and inside 12mm thick cement plastering (1:3) finished with a floating coat ofneat cement including fixing 100mmx100mm size HCI gully trap,150mmx150mm size C.I grating etc all complete as per approved drawing, specification and direction of the Engineer in charge |
| 592 | Gully Trap chamber |
| 593 | Supplying all materials, labour, T&P and constructing Inspection Chamber of the following sizewith cement concrete(1:3:6) using 40mm size hard granite metal on bed, 1st class Fly ash brickwork in cement mortar(1:6),moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips,12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab in (1:2:4) using 12mm size h.g chips with RCC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge |
| 594 | Inside size 760mm x 760mm x 460mm |
| 595 | Supplying all materials, labour, T&P and providing marble slab in urinal partition wall including cutting grooves in walls and making good the damages including watering curing etc all complete as per specification and direction of the E.I.C. |
| 596 | Supplying all materials, labour, T&P and providing granite tiles in slab, treads and landing on 25mm thick bed of cement mortar 1:1 (1 cement:1 sand) joined with neat cement slurry mixed with pigment to match the shades of the tiles etc all complete as per direction of the Engineer in charge |
| 597 | EXTERNAL PH WORK |
| 598 | (A).Sinking of 125mmX100/50mm dia. TubeWell by DTH Method |
| 599 | Supplying all material, labour, T&P for drilling aperfectly vertical bore hole of specified dia for a specified depth below ground level in hard rock stone, boulder etc by DTH Method drilling as required to suit the site condition as per the direction of Engineer-in-charge including use of own rigs with its accessories, tools and Plants and consumables etc. for lowering of finished bore suitable for lowering of 125mm dia GI/PVC pipes housing, fitted with socket and with or without well screen as per the necessity for the soft, medium, hard and boulder formation (GI/PVC pipes if required by the contractor to prevent collapse of over burden portion) including lower and withdrawing of casing pipe as per direction of EIC. (As per letter no 349 dt 11.01.2022 of Engineer-in-Chief, RWSS (O) |
| 600 | 0 Mtr. to100 Mtr. |
| 601 | Supplying all labour, T&P & joining materials & lowering the PVC casing pipes, fittings & well screens in position including fitting fixing of centralizer, rubber packer, cutter plug & washing the bore as per direction of Engineer-in-Charge. |
| 602 | a)125 mm dia ND PVCCasing pipe |
| 603 | Supplying all materials, labour, T&P cleaning and developing the tube well by compresser continuouslytill sand free clear water is obtained as per direction of E.I.C. |
| 604 | Supplying all materials, labour, T&P for IM II hand Pump set with 32mm dia GI riser pipes. |
| 605 | COST OF MATERIALS125mm ND PVC Casing Pipe ( Sch- 80 ) |
| 606 | Supply all materials, labour, T&P and providing,fitting and fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase/1phase line voltage ranging from 320 volt to 450 volt conforming to IS:8034/89 with following specifications with suitable control pannel, jointing with GI/PVC/HDPE pipes electrification, testing,commissioning,trial running,conveyance of all materials to worksite, payment of taxes etc all complete as per specification and direction of the Engineer in charge. |
| 607 | 1HP Single Phasesubmersible pump set. |
| 608 | DOL control panel |
| 609 | 50mm S. S. Nipple, S. S. bolt & clips |
| 610 | 50mm M. S. Clamp, Bend, Socket & 200mm M. S. well cap |
| 611 | 2.50mm Sqm Submersible flat cable |
| 612 | Steel rope with cover |
| 613 | 20mm dia rigid U-PVC pipe for Electrical cable |
| 614 | 40mm dia HDPE pipe |
| 615 | Labour charges for lowering, testing, commissioning & transportation to site etc. |
| 616 | Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor CPVC pipesof the following nominal bore and pipe fittings with clamps including making good the wall and testing as per specification and direction of the Engineer in charge |
| 617 | 40mm dia CPVCpipe |
| 618 | Earth work in all kinds of soil within 50 mtr initial lead and 1.5mtr initial lift includingrough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3 mtr in depth and as per direction of the Engineer in charge. |
| 619 | 50m x 0.45m x 0.60m = |
| 620 | Supplying all materials, labour, T&P and constructionman hole chamber of the following sizewith cement concrete(1:3:6) using 40mm size hard granite metal on bed, 1st class Fly ash brickwork in cement mortar(1:6), moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips,12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab in (1:1½:3) using 12mm size h.g chips with RCPC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge |
| 621 | Inside size 910mm x 910mm x 910mm |
| 622 | Supplying all materials, labour, T&P and constructing soakway pit of the following size with dry brick walling from bottom upto invert of inlet pipe and 1st class Fly Ash brickwork in cement mortar (1:6) for the remaining height at top, cement concrete (1:4:8) using 40mm size hg chips on bed, 12mm thick cement plaster (1:4) inside and outside over masonry brickwork, gravel backing in the rear of well steining, RCC cover slab in cement concrete (1:2:4) using 12mm size hg chips fitted with iron lifting handles including earthwork in open well excavation in all kinds of soil and refilling of cavity around the pit & painting the iron works, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge |
| 623 | 1.40m dia x 2.00m deep soakway pit |
| 624 | 1.20m dia x 2.00m deep soakway pit |
| 625 | Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized PVC pipes conforming to IS: 4985/2000 of the following outside dia for class–3(0.60mpa) including jointing with supply of approved solvent cement by non-heat application method/as per manufacturer’s specification, providing and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the Type C-1 standard bedding surrounding or encasingincluding concrete for bedding and curing etc all complete as per PH specification and direction of the Engineer in charge. |
| 626 | 110mm dia u-pvc pipe alround concrete |
| 627 | 160mm dia u-pvc pipe alround concrete |
| 628 | Construction 1 No 50 users RCC Septic tank |
| 629 | Earth work in excavation of foundation in all kinds of soil within 50m initial lead and 1.5m initial lift including rough dressing & breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3m in depth and as per direction of theEngineer-in-Charge. |
| 630 | 2nd Depth of 1.5 m |
| 631 | Supplying all materials,labour ,T&P and filling in foundation and plinth with sand well watered and rammed including cost, conveyance of all materials to work site ,payment of royalty,taxes etc. all complete as per direction of the Engineer-in -charge |
| 632 | In ground floor |
| 633 | Supplying all materials, labour, T&P andproviding cement concrete ( 1:4:8 ) with 4cm size crusher broken hard granite metal including watering, curing, cost of all materials,conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge. |
| 634 | In ground floor |
| 635 | Supplying all materials, labour, T&P and providing brick work with Fly Ash .bricks 25cmx12cmx8cm size having cs. not less than 75kg / cm2 with dimensional tolerance ± 8% inincluding watering,curing conveyance of all materials to worksite, payment of royalty taxes etc. all complete as per specification and direction of EIC. -- In Foundation & Plinth in CM (1:4) |
| 636 | Supplying all materials, labour, T&P and providing cement concrete ( 1:2:4 ) with 12mm size crusher broken hard black granite chips including watering, curing,cost of all materials, conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge |
| 637 | In ground floor |
| 638 | Supplying all materials, labour, T&P and providing cement concrete (1:1:5:3) with 12mm size hard broken granite chips for R.C.C works including hoisting, laying, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 639 | Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for R.C.C works including false work and dismantling them after casting including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 640 | For RCC wall |
| 641 | Supplying all materials, labour, T&P and providing M.Sreinforcement for R.C.C work including cutting, bending, binding, and tying the grills and placing in position including cost of binding wire 18 to 20 gauge, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 642 | In ground floor |
| 643 | Supplying all materials,labour,T&P and providing 16mm CP (1:6) with cement punning on brick work including watering,curing,cost of all materials, conveyance of all materials to worksite,paymentof royalty,all taxes etc.all complete as per PWD specification and direction of the Engineer-in-charge. |
| 644 | Supplying all materials, labour, T&P and providing cement plaster on brick/stone work including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc. all complete as per specification and direction of E.I.C.-12mm thick C.P with C.M. (1:6) |
| 645 | Bore Well Chamber- |
| 646 | Supplying all materials, labour, T&P and providing,fitting and fixing 100mm x 100mm x 100mm PVC Tee in wall including filling the recess with cement concrete (1:3:6) with 12mm size h.g chips all complete including watering, curing, conveyance of all materials to worksite, payment of royalty all complete as per specification anddirection of the Engineer in charge |
| 647 | Providing and fixing in position Polyproplene Foot steps of required shape and approved quality as per the direction of E.I.C. |
| 648 | Filling in foundation and plinth with excavated materials, moorum including watering and ramming as directed by the Engineer in charge |
| 649 | Supplying all materials, labour, T&P and fixing rotational moulded polyethylene cylindrical vertical waterstorage tank confirming to IS 12701- 1996 including cutting hole through the tank and fixing MS tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc. including hoisting the tankand placing the tankto the required position including all complete as per specification and direction of EIC.(including cost of 2000 liter capacity FG Over Head Tank) on roof of 1st Floor |
| 650 | Supplying all materials, labour, T&P and Construction of masonary stagging with providing 1st class KB. brick work in c.m, (1:6) of 0.46m. height in staging and in circular protection wall to support the tank in roof of ground floor using 25cm x 12cm x 8cm size KB. bricks having crushing strength not less than 75 kg/cm2 12mm thick c.p.(1:4) over brick work, R.C.C. Slab of size 1.64mtr xl.64mtr x0.l0mtr thick, R.C.C. beam of size 0.25m X 0.30m and 2.61m average length in c.c.(1:1.5:3) using 12mm size h.g. chips including centering and shuttering, watering, curing conveyance of all materials to work site etc. all complete as per specification and direction of E.I.C (2000 liter capacity FG Over Head Tank on roof of 1st Floor) |
| 651 | Providing and laying CERAMIC FLOOR TILESof premium grade and of approved size & shade in flooring on a bed of 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand) finished with flush pointing in white cement & pigment to match the shade of the tiles. |
| 652 | GroundFloor |
| 653 | First Floor |
| 654 | Supplying, fitting & fixing of Ceramic wall tiles of premium grade of size 300x200/200x200mm having thickness 6.5mm to 6.7mm confirming to IS 13753in dadoes, skirting and risers of stepslaid on 12 mm thick cement mortar (1:3) (1 cement : 3 course sand) jointed with slurry mixed with pigment to match the shades of the tiles etc. complete including cost of all materials, labour T&P etc. required for the work all complete as per direction of the Engineer-in-charge |
| 655 | GroundFloor |
| 656 | First Floor |
| 657 | Factory made GIRID FRP or called GRP sandwich compositedoor shutterof 32mm thick laminated with two GRP skin with good grain finishfabricated using UV stabilised isoppthalic gel coat and one layer of 450 gsm E-glass chopped strand mat (CSM) impregnated with ortopathilic resin The thickness of the skins shallnot be less than 1.50mm . Expanded polysryne ( EPS) structural foam panel of 29 mm tickness and a density of 20kg/cu.mts shall be used as core material wooden reinforcements made of sesasoned sal wood block of cross section not less than 28mm x 32mm and also necessary sal wood reinforcements for fitting the metal fittings such as lower bolts ,aldrops, handles etc. shall be provided . A structural adhesive compatible with (EPS)foam shall be used for bending the core material. the sal wood reinforcements and the skin The material and process for manufactuing te door shutter shallconform to RV -TIFAC components design centre\"s standards and specification and the door shutters tested in conformation to IS 4020-1998. The Finish of door shutter will be plain colour as per specificationand direction of the EngineerinCharge. etc. complete |
| 658 | ground floor and first floor |
| 659 | Factory made FRP( Altematly called GRP) door frame of size 75mm x 100mmfabricated using E - glass chopped strand mat (CSM) U.V stabilised inopathalic Gel coat and impregnated with inopathalic resin The thickness of the GRP skins shall not be less then 2.0 mm . The door frame consists of four segments which are provided with plug insocketarrrangement in-situ-in mould. The segments are plugged in and are joined together by means of srew. The GRP frame shall be provided with wooden reinforcement on six locations for high srew holding capacity for fixing metalic hold fast and shall be consolidated by filling with medium density foam / plaster of paris with fibre reinforcement , six number of 260mm x 25mm x 5mm size \"S\" shaped M.S flat holdfast shall be provided with the frame. The material and process for manufacturing the finish of door frame shall conform to RV-TIFAC composites Design centre\"s standards and specifications . The finish of door frame will be plain colour white /Ivory/Beige/Light grey / Golden brown / Mahogany/ Teak wood /sand stone Champagne/Pastel blue or any other colour using high quality pigment complete in all respect as per specification and direction of the Engineer in Charge.etc. complete |
| 660 | ground floor and first floor |
| 661 | P.H. works of Construction of 300 Capacity Multi Purpose Hall-2) Mz-Badagada(Near Badagada Brit Colony Chari Chhak) (300) |
| 662 | A- Internal PH Work |
| 663 | Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor C-PVC pipesconforming topipe fittings of the following nominal bore with clamps including making good the wall, ceilingand floor all complete as per specification and direction of the Engineer in charge |
| 664 | GroundFloor |
| 665 | 20mm dia C-PVC pipe (Ashirbad/Supreme) |
| 666 | 25mm dia C-PVC pipe (Ashirbad/Supreme) |
| 667 | In 1st Floor |
| 668 | 20mm dia C-PVC pipe (Ashirbad/Supreme) |
| 669 | 25mm dia C-PVC pipe (Ashirbad/Supreme) |
| 670 | 32mm dia C-PVC pipe (Ashirbad/Supreme) |
| 671 | In 2nd Floor |
| 672 | 40mm dia C-PVC pipe (Ashirbad/Supreme) |
| 673 | Supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking GI pipes and fittings/ PVC pipes and fittings etc all complete as per PH specification and direction of the Engineer in charge. |
| 674 | 250mmthick wall in Ground floor |
| 675 | In 1st Floor |
| 676 | Supplying all materials, labour, T&Pand cutting hole in R.C.C floors, roofs, etc upto 19 cm thickfor passing G.I. Pipes / P.V.C pipes and fittings etc and repairing the holes afterinsertion of pipes etc with cement concrete (1:2:4 ) including finishing complete so as to make it leak proof as per direction of theEngineer in charge. in Ground Floor |
| 677 | In 1st Floor |
| 678 | Supplying allmaterials, labour, T&P and cutting grooves in pucca floors and walls for takingGI/ PVC pipes and making good the damages as per the direction of the Engineer in charge. In Ground Floor |
| 679 | In 1st Floor |
| 680 | Supplying all materials, labour, T&P and cutting holes through existing brick or laterite masonry wall for taking PVC pipes and fittings including making good the damages etc all completeas per PH specification and direction of the Engineer in charge |
| 681 | 250mm to 375mmthick wall |
| 682 | in GroundFloor to Ist Floor |
| 683 | Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge |
| 684 | 15mm dia CP Long Body Bib cock (Jaquar) |
| 685 | 15mm dia CP angle stop cock(Jaquar) |
| 686 | 20mm dia CP consealed stop cock (Jaquar) |
| 687 | 15mm dia CP two in one bib cock (Jaquar) |
| 688 | 15mm dia CP Health faucet (Jaquar) |
| 689 | 15mm dia CP extension piece |
| 690 | 15mm dia CP Pillar cock (Jaquar) |
| 691 | 25mm dia G.M or Brass F.W valve (Sakti make) |
| 692 | 32mm dia PVC F.W valve |
| 693 | 40mm dia PVC F.W valve |
| 694 | 125mm dia CP gratings |
| 695 | 15mm dia CP revolving shower (Jaquar make) |
| 696 | 15mm dia CP Auto closing Urinal Flush Valve (PRS-CHR-077 Jaquar make) |
| 697 | Supplying all materials, labour, T&P and fitting and fixing 10 litres capacity low level flushing cistern with a pair of cast iron or M.S brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle, unions and couplings for connection with inlet, outlet and overflow pipes,32mm dia CP flush bend,15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting the inlet pipe with supply main etc all complete as per specification and direction of the Engineer in charge |
| 698 | 10 litres PVC L.L. Cistern (Slimline-white) |
| 699 | Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricantby non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge |
| 700 | 75mm dia U-PVC SWR pipes(Supreme/Ashirvad) |
| 701 | 75mm U-PVC plain bend |
| 702 | 110mm dia U-PVC SWR pipes(Supreme/Ashirvad) |
| 703 | 110mm U-PVC door bend |
| 704 | 110mm U-PVC door Tee |
| 705 | 110mm U-PVC plain Tee |
| 706 | 110mm dia U-PVC offset without ear |
| 707 | 110mm U-PVC plain bend |
| 708 | 110mm U-PVC vent cowl |
| 709 | 110mm dia U-PVC \"P\" trap |
| 710 | 110mm dia U-PVC socket plain |
| 711 | 75mm dia U-PVC socket plain |
| 712 | PVC Clamp |
| 713 | 110mm U-PVC door cross Tee |
| 714 | Supplying all materials, labour T&Pand fixing water closet, (Orissa pattern squating pan) duly embeded in c.c. (1:5:10) using 4cm h.g. metal all complete as per direction of E.I.C.--(583x440)mm Orissa pan (Neycer/Cerra/ Parry ware/ Hindware) |
| 715 | 580mm size Orissa pan(Hindware/Parryware/Neycer) |
| 716 | Supplying all materials, labour, T&P and fixing bowl pattern urinal including connecting the urinal with waste pipe by means of white lead mixed with chopped hemp etc all complete as per specification and direction of the Engineer in charge. |
| 717 | Halfstall wall Urinal (Parryware/Hindware/Neycer) |
| 718 | 15mm dia Urinal spreder |
| 719 | 32mm dia Dome waste |
| 720 | Supplying all materials, labour, T&P and fixing Wash Down Water Closet (European type W.C pan) with integral ‘S’ or ‘P’ trap to the floor with wooden plug and chromium plated screws including jointing the trap with soil pipe in cement mortar (1:1) etc all complete as per specification and direction of the Engineer in charge. |
| 721 | E.W.C. with seat cover (Parryware/Hindware/Neycer) |
| 722 | Supplying all materials, labour, T&P fitting and fixing Plastic Seat and cover for E.W.C. with chromium plated brass hinges and rubber buffers all complete as perr specification and direction of E.I.C. (Neycer/ Cerra/Parry ware/ Hindware) |
| 723 | EWC (Matrix set) Hindware No.70002(P-18)(WHB 65 x 35 with one pair mounting brackets, EWC & Cistern complete with fittings & seat cover, one no hinged rail 76 cm and five nos of grab rails 60 cm) |
| 724 | Supplying all materials, labour T&P and fixing wash basins with hole for pillar taps with C.I/M.S brackets painted white including holes in walls and making good the damages etc. all complete as per P.H specification and direction of E.I.C.-- 550mm x 400mm WHB with all Fittings with C.P. Waste, PVC Waste Pipe & Connection Pipe. (Neycer/Cerra/ Parry ware/ Hindware) |
| 725 | Supplying all materials, labour T&P and fixing padestrial for wash basin complete recessed at the back for the reception of pipe and fitting etc. all complete as per specification and direction of E.I.C. (Neycer/Parrywear/Cerra/Hindware) |
| 726 | Under Counterbasin(560x450)Hindware-No.10095 |
| 727 | Supplying all materials, labour, T&P and fixing mirror of superior glass conforming to IS:3438-1996 mounted on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification an direction of the Engineer in charge |
| 728 | 600mm x 450mm size B.E mirror |
| 729 | Large size mirror with frame |
| 730 | 2 x 3.00 x0.90= |
| 731 | Supplying all materials, labour, T&P and fixing standard sized glass-shelf with CP brass brackets and guard rails complete fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge |
| 732 | 600 x 125mm plate glass shelf with CP guard rails (Plaza/Amber/Aquatic) |
| 733 | Supplying all materials, labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge |
| 734 | 25mm x 600mm long CP towel rail (Plaza/Amber/Aquatic) |
| 735 | CP towel Ring (Plaza/Amber/Aquatic) |
| 736 | Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge |
| 737 | CP soap holder(Plaza/Amber/Aquatic) |
| 738 | Supplying all materials, labour, T&P and fixing wash kitchen sink/laboratory sink with outlet at end and weir overflow including fitting and fixing a pair of cast iron or MS brackets painted white, fixing 50mm/40mm dia CP brass waste, fixing 50mm/40mm dia PVC waste pipe 910mm long with supply of wooden plugs, screws and cement etc including cutting holes in walls and making good the damages etc all complete as per specification and direction of the Engineer in charge |
| 739 | 550 x 450 x 200mm size S/S kitchen sink (Jayana make ) |
| 740 | Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including cement punning,watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 741 | In Ist Floor |
| 742 | Providing and laying Sika top seal 109 hi over roof top slab and parapet ,toilet inside after cleaning of surface and applied with a coat of Sika 109 hi primer as per approved specification.The Sika shall be laid between two coats of water proofing membrance and the entire application cover with Sika top seak hi curing,compoundof all materials and cost of labour T&P etc.complete as per the direction of the Engineer-in-charge. |
| 743 | In Ist Floor |
| 744 | Supplying all materials labour T&P and filling in foundation and plinth with sandwellwatered and rammed including conveyance of all materials to work sitepayment of royalty taxes etc all complete as per direction ofEngineer in charge In ground floor |
| 745 | In 1st Floor |
| 746 | Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard granite chips broken including watering, curing, conveyance of all materials to worksite, payment of royality, taxes etc all complete as aper specification and direction of the E.I.C. -In Ground Floor |
| 747 | In 1st Floor |
| 748 | Supplying all materials, labour, T&P and constructing Gully Trap chamber of the following inside size with 8cm thick R.C.C precast cover slab in cement concrete (1:2:4) mix using 12mm size h.g chips, foundation concrete (1:4:8) using 40mm size hard granite metal on bed and around trap, Fly ash brickwork in c.m (1:6) in F&P and inside 12mm thick cement plastering (1:3) finished with a floating coat ofneat cement including fixing 100mmx100mm size HCI gully trap,150mmx150mm size C.I grating etc all complete as per approved drawing, specification and direction of the Engineer in charge |
| 749 | Gully Trap chamber |
| 750 | Supplying all materials, labour, T&P and constructing Inspection Chamber of the following sizewith cement concrete(1:3:6) using 40mm size hard granite metal on bed, 1st class Fly ash brickwork in cement mortar(1:6),moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips,12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab in (1:2:4) using 12mm size h.g chips with RCC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge |
| 751 | Inside size 760mm x 760mm x 460mm |
| 752 | Supplying all materials, labour, T&P and providing marble slab in urinal partition wall including cutting grooves in walls and making good the damages including watering curing etc all complete as per specification and direction of the E.I.C. |
| 753 | Supplying all materials, labour, T&P and providing granite tiles in slab, treads and landing on 25mm thick bed of cement mortar 1:1 (1 cement:1 sand) joined with neat cement slurry mixed with pigment to match the shades of the tiles etc all complete as per direction of the Engineer in charge |
| 754 | EXTERNAL PH WORK |
| 755 | (A).Sinking of 125mmX100/50mm dia. TubeWell by DTH Method |
| 756 | Supplying all material, labour, T&P for drilling aperfectly vertical bore hole of specified dia for a specified depth below ground level in hard rock stone, boulder etc by DTH Method drilling as required to suit the site condition as per the direction of Engineer-in-charge including use of own rigs with its accessories, tools and Plants and consumables etc. for lowering of finished bore suitable for lowering of 125mm dia GI/PVC pipes housing, fitted with socket and with or without well screen as per the necessity for the soft, medium, hard and boulder formation (GI/PVC pipes if required by the contractor to prevent collapse of over burden portion) including lower and withdrawing of casing pipe as per direction of EIC. (As per letter no 349 dt 11.01.2022 of Engineer-in-Chief, RWSS (O) |
| 757 | 0 Mtr. to100 Mtr. |
| 758 | Supplying all labour, T&P & joining materials & lowering the PVC casing pipes, fittings & well screens in position including fitting fixing of centralizer, rubber packer, cutter plug & washing the bore as per direction of Engineer-in-Charge. |
| 759 | a)125 mm dia ND PVCCasing pipe |
| 760 | Supplying all materials, labour, T&P cleaning and developing the tube well by compresser continuouslytill sand free clear water is obtained as per direction of E.I.C. |
| 761 | Supplying all materials, labour, T&P for IM II hand Pump set with 32mm dia GI riser pipes. |
| 762 | COST OF MATERIALS125mm ND PVC Casing Pipe ( Sch- 80 ) |
| 763 | Supply all materials, labour, T&P and providing,fitting and fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase/1phase line voltage ranging from 320 volt to 450 volt conforming to IS:8034/89 with following specifications with suitable control pannel, jointing with GI/PVC/HDPE pipes electrification, testing,commissioning,trial running,conveyance of all materials to worksite, payment of taxes etc all complete as per specification and direction of the Engineer in charge. |
| 764 | 1HP Single Phasesubmersible pump set. |
| 765 | DOL control panel |
| 766 | 50mm S. S. Nipple, S. S. bolt & clips |
| 767 | 50mm M. S. Clamp, Bend, Socket & 200mm M. S. well cap |
| 768 | 2.50mm Sqm Submersible flat cable |
| 769 | Steel rope with cover |
| 770 | 20mm dia rigid U-PVC pipe for Electrical cable |
| 771 | 40mm dia HDPE pipe |
| 772 | Labour charges for lowering, testing, commissioning & transportation to site etc. |
| 773 | Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor CPVC pipesof the following nominal bore and pipe fittings with clamps including making good the wall and testing as per specification and direction of the Engineer in charge |
| 774 | 40mm dia CPVCpipe |
| 775 | Earth work in all kinds of soil within 50 mtr initial lead and 1.5mtr initial lift includingrough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3 mtr in depth and as per direction of the Engineer in charge. |
| 776 | 50m x 0.45m x 0.60m = |
| 777 | Supplying all materials, labour, T&P and constructionman hole chamber of the following sizewith cement concrete(1:3:6) using 40mm size hard granite metal on bed, 1st class Fly ash brickwork in cement mortar(1:6), moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips,12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab in (1:1½:3) using 12mm size h.g chips with RCPC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge |
| 778 | Inside size 910mm x 910mm x 910mm |
| 779 | Supplying all materials, labour, T&P and constructing soakway pit of the following size with dry brick walling from bottom upto invert of inlet pipe and 1st class Fly Ash brickwork in cement mortar (1:6) for the remaining height at top, cement concrete (1:4:8) using 40mm size hg chips on bed, 12mm thick cement plaster (1:4) inside and outside over masonry brickwork, gravel backing in the rear of well steining, RCC cover slab in cement concrete (1:2:4) using 12mm size hg chips fitted with iron lifting handles including earthwork in open well excavation in all kinds of soil and refilling of cavity around the pit & painting the iron works, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge |
| 780 | 1.40m dia x 2.00m deep soakway pit |
| 781 | 1.20m dia x 2.00m deep soakway pit |
| 782 | Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized PVC pipes conforming to IS: 4985/2000 of the following outside dia for class–3(0.60mpa) including jointing with supply of approved solvent cement by non-heat application method/as per manufacturer’s specification, providing and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the Type C-1 standard bedding surrounding or encasingincluding concrete for bedding and curing etc all complete as per PH specification and direction of the Engineer in charge. |
| 783 | 110mm dia u-pvc pipe alround concrete |
| 784 | 160mm dia u-pvc pipe alround concrete |
| 785 | Construction 1 No 50 users RCC Septic tank |
| 786 | Earth work in excavation of foundation in all kinds of soil within 50m initial lead and 1.5m initial lift including rough dressing & breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3m in depth and as per direction of theEngineer-in-Charge. |
| 787 | 2nd Depth of 1.5 m |
| 788 | Supplying all materials,labour ,T&P and filling in foundation and plinth with sand well watered and rammed including cost, conveyance of all materials to work site ,payment of royalty,taxes etc. all complete as per direction of the Engineer-in -charge |
| 789 | In ground floor |
| 790 | Supplying all materials, labour, T&P andproviding cement concrete ( 1:4:8 ) with 4cm size crusher broken hard granite metal including watering, curing, cost of all materials,conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge. |
| 791 | In ground floor |
| 792 | Supplying all materials, labour, T&P and providing brick work with Fly Ash .bricks 25cmx12cmx8cm size having cs. not less than 75kg / cm2 with dimensional tolerance ± 8% inincluding watering,curing conveyance of all materials to worksite, payment of royalty taxes etc. all complete as per specification and direction of EIC. -- In Foundation & Plinth in CM (1:4) |
| 793 | Supplying all materials, labour, T&P and providing cement concrete ( 1:2:4 ) with 12mm size crusher broken hard black granite chips including watering, curing,cost of all materials, conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge |
| 794 | In ground floor |
| 795 | Supplying all materials, labour, T&P and providing cement concrete (1:1:5:3) with 12mm size hard broken granite chips for R.C.C works including hoisting, laying, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 796 | Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for R.C.C works including false work and dismantling them after casting including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 797 | For RCC wall |
| 798 | Supplying all materials, labour, T&P and providing M.Sreinforcement for R.C.C work including cutting, bending, binding, and tying the grills and placing in position including cost of binding wire 18 to 20 gauge, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 799 | In ground floor |
| 800 | Supplying all materials,labour,T&P and providing 16mm CP (1:6) with cement punning on brick work including watering,curing,cost of all materials, conveyance of all materials to worksite,paymentof royalty,all taxes etc.all complete as per PWD specification and direction of the Engineer-in-charge. |
| 801 | Supplying all materials, labour, T&P and providing cement plaster on brick/stone work including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc. all complete as per specification and direction of E.I.C.-12mm thick C.P with C.M. (1:6) |
| 802 | Bore Well Chamber- |
| 803 | Supplying all materials, labour, T&P and providing,fitting and fixing 100mm x 100mm x 100mm PVC Tee in wall including filling the recess with cement concrete (1:3:6) with 12mm size h.g chips all complete including watering, curing, conveyance of all materials to worksite, payment of royalty all complete as per specification anddirection of the Engineer in charge |
| 804 | Providing and fixing in position Polyproplene Foot steps of required shape and approved quality as per the direction of E.I.C. |
| 805 | Filling in foundation and plinth with excavated materials, moorum including watering and ramming as directed by the Engineer in charge |
| 806 | Supplying all materials, labour, T&P and fixing rotational moulded polyethylene cylindrical vertical waterstorage tank confirming to IS 12701- 1996 including cutting hole through the tank and fixing MS tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc. including hoisting the tankand placing the tankto the required position including all complete as per specification and direction of EIC.(including cost of 2000 liter capacity FG Over Head Tank) on roof of 1st Floor |
| 807 | Supplying all materials, labour, T&P and Construction of masonary stagging with providing 1st class KB. brick work in c.m, (1:6) of 0.46m. height in staging and in circular protection wall to support the tank in roof of ground floor using 25cm x 12cm x 8cm size KB. bricks having crushing strength not less than 75 kg/cm2 12mm thick c.p.(1:4) over brick work, R.C.C. Slab of size 1.64mtr xl.64mtr x0.l0mtr thick, R.C.C. beam of size 0.25m X 0.30m and 2.61m average length in c.c.(1:1.5:3) using 12mm size h.g. chips including centering and shuttering, watering, curing conveyance of all materials to work site etc. all complete as per specification and direction of E.I.C (2000 liter capacity FG Over Head Tank on roof of 1st Floor) |
| 808 | Providing and laying CERAMIC FLOOR TILESof premium grade and of approved size & shade in flooring on a bed of 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand) finished with flush pointing in white cement & pigment to match the shade of the tiles. |
| 809 | GroundFloor |
| 810 | First Floor |
| 811 | Supplying, fitting & fixing of Ceramic wall tiles of premium grade of size 300x200/200x200mm having thickness 6.5mm to 6.7mm confirming to IS 13753in dadoes, skirting and risers of stepslaid on 12 mm thick cement mortar (1:3) (1 cement : 3 course sand) jointed with slurry mixed with pigment to match the shades of the tiles etc. complete including cost of all materials, labour T&P etc. required for the work all complete as per direction of the Engineer-in-charge |
| 812 | GroundFloor |
| 813 | First Floor |
| 814 | Factory made GIRID FRP or called GRP sandwich compositedoor shutterof 32mm thick laminated with two GRP skin with good grain finishfabricated using UV stabilised isoppthalic gel coat and one layer of 450 gsm E-glass chopped strand mat (CSM) impregnated with ortopathilic resin The thickness of the skins shallnot be less than 1.50mm . Expanded polysryne ( EPS) structural foam panel of 29 mm tickness and a density of 20kg/cu.mts shall be used as core material wooden reinforcements made of sesasoned sal wood block of cross section not less than 28mm x 32mm and also necessary sal wood reinforcements for fitting the metal fittings such as lower bolts ,aldrops, handles etc. shall be provided . A structural adhesive compatible with (EPS)foam shall be used for bending the core material. the sal wood reinforcements and the skin The material and process for manufactuing te door shutter shallconform to RV -TIFAC components design centre\"s standards and specification and the door shutters tested in conformation to IS 4020-1998. The Finish of door shutter will be plain colour as per specificationand direction of the EngineerinCharge. etc. complete |
| 815 | ground floor and first floor |
| 816 | Factory made FRP( Altematly called GRP) door frame of size 75mm x 100mmfabricated using E - glass chopped strand mat (CSM) U.V stabilised inopathalic Gel coat and impregnated with inopathalic resin The thickness of the GRP skins shall not be less then 2.0 mm . The door frame consists of four segments which are provided with plug insocketarrrangement in-situ-in mould. The segments are plugged in and are joined together by means of srew. The GRP frame shall be provided with wooden reinforcement on six locations for high srew holding capacity for fixing metalic hold fast and shall be consolidated by filling with medium density foam / plaster of paris with fibre reinforcement , six number of 260mm x 25mm x 5mm size \"S\" shaped M.S flat holdfast shall be provided with the frame. The material and process for manufacturing the finish of door frame shall conform to RV-TIFAC composites Design centre\"s standards and specifications . The finish of door frame will be plain colour white /Ivory/Beige/Light grey / Golden brown / Mahogany/ Teak wood /sand stone Champagne/Pastel blue or any other colour using high quality pigment complete in all respect as per specification and direction of the Engineer in Charge.etc. complete |
| 817 | ground floor and first floor |
| 818 | P.H. works of Construction of 300 Capacity Multi Purpose Hall-3) Mz-Bhouma Nagar (Near RBI Colony Unit- IV) (300) |
| 819 | A- Internal PH Work |
| 820 | Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor C-PVC pipesconforming topipe fittings of the following nominal bore with clamps including making good the wall, ceilingand floor all complete as per specification and direction of the Engineer in charge |
| 821 | GroundFloor |
| 822 | 20mm dia C-PVC pipe (Ashirbad/Supreme) |
| 823 | 25mm dia C-PVC pipe (Ashirbad/Supreme) |
| 824 | In 1st Floor |
| 825 | 20mm dia C-PVC pipe (Ashirbad/Supreme) |
| 826 | 25mm dia C-PVC pipe (Ashirbad/Supreme) |
| 827 | 32mm dia C-PVC pipe (Ashirbad/Supreme) |
| 828 | In 2nd Floor |
| 829 | 40mm dia C-PVC pipe (Ashirbad/Supreme) |
| 830 | Supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking GI pipes and fittings/ PVC pipes and fittings etc all complete as per PH specification and direction of the Engineer in charge. |
| 831 | 250mmthick wall in Ground floor |
| 832 | In 1st Floor |
| 833 | Supplying all materials, labour, T&Pand cutting hole in R.C.C floors, roofs, etc upto 19 cm thickfor passing G.I. Pipes / P.V.C pipes and fittings etc and repairing the holes afterinsertion of pipes etc with cement concrete (1:2:4 ) including finishing complete so as to make it leak proof as per direction of theEngineer in charge. in Ground Floor |
| 834 | In 1st Floor |
| 835 | Supplying allmaterials, labour, T&P and cutting grooves in pucca floors and walls for takingGI/ PVC pipes and making good the damages as per the direction of the Engineer in charge. In Ground Floor |
| 836 | In 1st Floor |
| 837 | Supplying all materials, labour, T&P and cutting holes through existing brick or laterite masonry wall for taking PVC pipes and fittings including making good the damages etc all completeas per PH specification and direction of the Engineer in charge |
| 838 | 250mm to 375mmthick wall |
| 839 | in GroundFloor to Ist Floor |
| 840 | Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge |
| 841 | 15mm dia CP Long Body Bib cock (Jaquar) |
| 842 | 15mm dia CP angle stop cock(Jaquar) |
| 843 | 20mm dia CP consealed stop cock (Jaquar) |
| 844 | 15mm dia CP two in one bib cock (Jaquar) |
| 845 | 15mm dia CP Health faucet (Jaquar) |
| 846 | 15mm dia CP extension piece |
| 847 | 15mm dia CP Pillar cock (Jaquar) |
| 848 | 25mm dia G.M or Brass F.W valve (Sakti make) |
| 849 | 32mm dia PVC F.W valve |
| 850 | 40mm dia PVC F.W valve |
| 851 | 125mm dia CP gratings |
| 852 | 15mm dia CP revolving shower (Jaquar make) |
| 853 | 15mm dia CP Auto closing Urinal Flush Valve (PRS-CHR-077 Jaquar make) |
| 854 | Supplying all materials, labour, T&P and fitting and fixing 10 litres capacity low level flushing cistern with a pair of cast iron or M.S brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle, unions and couplings for connection with inlet, outlet and overflow pipes,32mm dia CP flush bend,15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting the inlet pipe with supply main etc all complete as per specification and direction of the Engineer in charge |
| 855 | 10 litres PVC L.L. Cistern (Slimline-white) |
| 856 | Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricantby non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge |
| 857 | 75mm dia U-PVC SWR pipes(Supreme/Ashirvad) |
| 858 | 75mm U-PVC plain bend |
| 859 | 110mm dia U-PVC SWR pipes(Supreme/Ashirvad) |
| 860 | 110mm U-PVC door bend |
| 861 | 110mm U-PVC door Tee |
| 862 | 110mm U-PVC plain Tee |
| 863 | 110mm dia U-PVC offset without ear |
| 864 | 110mm U-PVC plain bend |
| 865 | 110mm U-PVC vent cowl |
| 866 | 110mm dia U-PVC \"P\" trap |
| 867 | 110mm dia U-PVC socket plain |
| 868 | 75mm dia U-PVC socket plain |
| 869 | PVC Clamp |
| 870 | 110mm U-PVC door cross Tee |
| 871 | Supplying all materials, labour T&Pand fixing water closet, (Orissa pattern squating pan) duly embeded in c.c. (1:5:10) using 4cm h.g. metal all complete as per direction of E.I.C.--(583x440)mm Orissa pan (Neycer/Cerra/ Parry ware/ Hindware) |
| 872 | 580mm size Orissa pan(Hindware/Parryware/Neycer) |
| 873 | Supplying all materials, labour, T&P and fixing bowl pattern urinal including connecting the urinal with waste pipe by means of white lead mixed with chopped hemp etc all complete as per specification and direction of the Engineer in charge. |
| 874 | Halfstall wall Urinal (Parryware/Hindware/Neycer) |
| 875 | 15mm dia Urinal spreder |
| 876 | 32mm dia Dome waste |
| 877 | Supplying all materials, labour, T&P and fixing Wash Down Water Closet (European type W.C pan) with integral ‘S’ or ‘P’ trap to the floor with wooden plug and chromium plated screws including jointing the trap with soil pipe in cement mortar (1:1) etc all complete as per specification and direction of the Engineer in charge. |
| 878 | E.W.C. with seat cover (Parryware/Hindware/Neycer) |
| 879 | Supplying all materials, labour, T&P fitting and fixing Plastic Seat and cover for E.W.C. with chromium plated brass hinges and rubber buffers all complete as perr specification and direction of E.I.C. (Neycer/ Cerra/Parry ware/ Hindware) |
| 880 | EWC (Matrix set) Hindware No.70002(P-18)(WHB 65 x 35 with one pair mounting brackets, EWC & Cistern complete with fittings & seat cover, one no hinged rail 76 cm and five nos of grab rails 60 cm) |
| 881 | Supplying all materials, labour T&P and fixing wash basins with hole for pillar taps with C.I/M.S brackets painted white including holes in walls and making good the damages etc. all complete as per P.H specification and direction of E.I.C.-- 550mm x 400mm WHB with all Fittings with C.P. Waste, PVC Waste Pipe & Connection Pipe. (Neycer/Cerra/ Parry ware/ Hindware) |
| 882 | Supplying all materials, labour T&P and fixing padestrial for wash basin complete recessed at the back for the reception of pipe and fitting etc. all complete as per specification and direction of E.I.C. (Neycer/Parrywear/Cerra/Hindware) |
| 883 | Under Counterbasin(560x450)Hindware-No.10095 |
| 884 | Supplying all materials, labour, T&P and fixing mirror of superior glass conforming to IS:3438-1996 mounted on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification an direction of the Engineer in charge |
| 885 | 600mm x 450mm size B.E mirror |
| 886 | Large size mirror with frame |
| 887 | 2 x 3.00 xx0.90= |
| 888 | Supplying all materials, labour, T&P and fixing standard sized glass-shelf with CP brass brackets and guard rails complete fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge |
| 889 | 600 x 125mm plate glass shelf with CP guard rails (Plaza/Amber/Aquatic) |
| 890 | Supplying all materials, labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge |
| 891 | 25mm x 600mm long CP towel rail (Plaza/Amber/Aquatic) |
| 892 | CP towel Ring (Plaza/Amber/Aquatic) |
| 893 | Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge |
| 894 | CP soap holder(Plaza/Amber/Aquatic) |
| 895 | Supplying all materials, labour, T&P and fixing wash kitchen sink/laboratory sink with outlet at end and weir overflow including fitting and fixing a pair of cast iron or MS brackets painted white, fixing 50mm/40mm dia CP brass waste, fixing 50mm/40mm dia PVC waste pipe 910mm long with supply of wooden plugs, screws and cement etc including cutting holes in walls and making good the damages etc all complete as per specification and direction of the Engineer in charge |
| 896 | 550 x 450 x 200mm size S/S kitchen sink (Jayana make ) |
| 897 | Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including cement punning,watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 898 | In Ist Floor |
| 899 | Providing and laying Sika top seal 109 hi over roof top slab and parapet ,toilet inside after cleaning of surface and applied with a coat of Sika 109 hi primer as per approved specification.The Sika shall be laid between two coats of water proofing membrance and the entire application cover with Sika top seak hi curing,compoundof all materials and cost of labour T&P etc.complete as per the direction of the Engineer-in-charge. |
| 900 | In Ist Floor |
| 901 | Supplying all materials labour T&P and filling in foundation and plinth with sandwellwatered and rammed including conveyance of all materials to work sitepayment of royalty taxes etc all complete as per direction ofEngineer in charge In ground floor |
| 902 | In 1st Floor |
| 903 | Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard granite chips broken including watering, curing, conveyance of all materials to worksite, payment of royality, taxes etc all complete as aper specification and direction of the E.I.C. -In Ground Floor |
| 904 | In 1st Floor |
| 905 | Supplying all materials, labour, T&P and constructing Gully Trap chamber of the following inside size with 8cm thick R.C.C precast cover slab in cement concrete (1:2:4) mix using 12mm size h.g chips, foundation concrete (1:4:8) using 40mm size hard granite metal on bed and around trap, Fly ash brickwork in c.m (1:6) in F&P and inside 12mm thick cement plastering (1:3) finished with a floating coat ofneat cement including fixing 100mmx100mm size HCI gully trap,150mmx150mm size C.I grating etc all complete as per approved drawing, specification and direction of the Engineer in charge |
| 906 | Gully Trap chamber |
| 907 | Supplying all materials, labour, T&P and constructing Inspection Chamber of the following sizewith cement concrete(1:3:6) using 40mm size hard granite metal on bed, 1st class Fly ash brickwork in cement mortar(1:6),moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips,12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab in (1:2:4) using 12mm size h.g chips with RCC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge |
| 908 | Inside size 760mm x 760mm x 460mm |
| 909 | Supplying all materials, labour, T&P and providing marble slab in urinal partition wall including cutting grooves in walls and making good the damages including watering curing etc all complete as per specification and direction of the E.I.C. |
| 910 | Supplying all materials, labour, T&P and providing granite tiles in slab, treads and landing on 25mm thick bed of cement mortar 1:1 (1 cement:1 sand) joined with neat cement slurry mixed with pigment to match the shades of the tiles etc all complete as per direction of the Engineer in charge |
| 911 | EXTERNAL PH WORK |
| 912 | (A).Sinking of 125mmX100/50mm dia. TubeWell by DTH Method |
| 913 | Supplying all material, labour, T&P for drilling aperfectly vertical bore hole of specified dia for a specified depth below ground level in hard rock stone, boulder etc by DTH Method drilling as required to suit the site condition as per the direction of Engineer-in-charge including use of own rigs with its accessories, tools and Plants and consumables etc. for lowering of finished bore suitable for lowering of 125mm dia GI/PVC pipes housing, fitted with socket and with or without well screen as per the necessity for the soft, medium, hard and boulder formation (GI/PVC pipes if required by the contractor to prevent collapse of over burden portion) including lower and withdrawing of casing pipe as per direction of EIC. (As per letter no 349 dt 11.01.2022 of Engineer-in-Chief, RWSS (O) |
| 914 | 0 Mtr. to100 Mtr. |
| 915 | Supplying all labour, T&P & joining materials & lowering the PVC casing pipes, fittings & well screens in position including fitting fixing of centralizer, rubber packer, cutter plug & washing the bore as per direction of Engineer-in-Charge. |
| 916 | a)125 mm dia ND PVCCasing pipe |
| 917 | Supplying all materials, labour, T&P cleaning and developing the tube well by compresser continuouslytill sand free clear water is obtained as per direction of E.I.C. |
| 918 | Supplying all materials, labour, T&P for IM II hand Pump set with 32mm dia GI riser pipes. |
| 919 | COST OF MATERIALS125mm ND PVC Casing Pipe ( Sch- 80 ) |
| 920 | Supply all materials, labour, T&P and providing,fitting and fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase/1phase line voltage ranging from 320 volt to 450 volt conforming to IS:8034/89 with following specifications with suitable control pannel, jointing with GI/PVC/HDPE pipes electrification, testing,commissioning,trial running,conveyance of all materials to worksite, payment of taxes etc all complete as per specification and direction of the Engineer in charge. |
| 921 | 1HP Single Phasesubmersible pump set. |
| 922 | DOL control panel |
| 923 | 50mm S. S. Nipple, S. S. bolt & clips |
| 924 | 50mm M. S. Clamp, Bend, Socket & 200mm M. S. well cap |
| 925 | 2.50mm Sqm Submersible flat cable |
| 926 | Steel rope with cover |
| 927 | 20mm dia rigid U-PVC pipe for Electrical cable |
| 928 | 40mm dia HDPE pipe |
| 929 | Labour charges for lowering, testing, commissioning & transportation to site etc. |
| 930 | Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor CPVC pipesof the following nominal bore and pipe fittings with clamps including making good the wall and testing as per specification and direction of the Engineer in charge |
| 931 | 40mm dia CPVCpipe |
| 932 | Earth work in all kinds of soil within 50 mtr initial lead and 1.5mtr initial lift includingrough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3 mtr in depth and as per direction of the Engineer in charge. |
| 933 | 50m x 0.45m x 0.60m = |
| 934 | Supplying all materials, labour, T&P and constructionman hole chamber of the following sizewith cement concrete(1:3:6) using 40mm size hard granite metal on bed, 1st class Fly ash brickwork in cement mortar(1:6), moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips,12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab in (1:1½:3) using 12mm size h.g chips with RCPC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge |
| 935 | Inside size 910mm x 910mm x 910mm |
| 936 | Supplying all materials, labour, T&P and constructing soakway pit of the following size with dry brick walling from bottom upto invert of inlet pipe and 1st class Fly Ash brickwork in cement mortar (1:6) for the remaining height at top, cement concrete (1:4:8) using 40mm size hg chips on bed, 12mm thick cement plaster (1:4) inside and outside over masonry brickwork, gravel backing in the rear of well steining, RCC cover slab in cement concrete (1:2:4) using 12mm size hg chips fitted with iron lifting handles including earthwork in open well excavation in all kinds of soil and refilling of cavity around the pit & painting the iron works, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge |
| 937 | 1.40m dia x 2.00m deep soakway pit |
| 938 | 1.20m dia x 2.00m deep soakway pit |
| 939 | Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized PVC pipes conforming to IS: 4985/2000 of the following outside dia for class–3(0.60mpa) including jointing with supply of approved solvent cement by non-heat application method/as per manufacturer’s specification, providing and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the Type C-1 standard bedding surrounding or encasingincluding concrete for bedding and curing etc all complete as per PH specification and direction of the Engineer in charge. |
| 940 | 110mm dia u-pvc pipe alround concrete |
| 941 | 160mm dia u-pvc pipe alround concrete |
| 942 | Construction 1 No 50 users RCC Septic tank |
| 943 | Earth work in excavation of foundation in all kinds of soil within 50m initial lead and 1.5m initial lift including rough dressing & breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3m in depth and as per direction of theEngineer-in-Charge. |
| 944 | 2nd Depth of 1.5 m |
| 945 | Supplying all materials,labour ,T&P and filling in foundation and plinth with sand well watered and rammed including cost, conveyance of all materials to work site ,payment of royalty,taxes etc. all complete as per direction of the Engineer-in -charge |
| 946 | In ground floor |
| 947 | Supplying all materials, labour, T&P andproviding cement concrete ( 1:4:8 ) with 4cm size crusher broken hard granite metal including watering, curing, cost of all materials,conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge. |
| 948 | In ground floor |
| 949 | Supplying all materials, labour, T&P and providing brick work with Fly Ash .bricks 25cmx12cmx8cm size having cs. not less than 75kg / cm2 with dimensional tolerance ± 8% inincluding watering,curing conveyance of all materials to worksite, payment of royalty taxes etc. all complete as per specification and direction of EIC. -- In Foundation & Plinth in CM (1:4) |
| 950 | Supplying all materials, labour, T&P and providing cement concrete ( 1:2:4 ) with 12mm size crusher broken hard black granite chips including watering, curing,cost of all materials, conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge |
| 951 | In ground floor |
| 952 | Supplying all materials, labour, T&P and providing cement concrete (1:1:5:3) with 12mm size hard broken granite chips for R.C.C works including hoisting, laying, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 953 | Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for R.C.C works including false work and dismantling them after casting including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 954 | For RCC wall |
| 955 | Supplying all materials, labour, T&P and providing M.Sreinforcement for R.C.C work including cutting, bending, binding, and tying the grills and placing in position including cost of binding wire 18 to 20 gauge, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 956 | In ground floor |
| 957 | Supplying all materials,labour,T&P and providing 16mm CP (1:6) with cement punning on brick work including watering,curing,cost of all materials, conveyance of all materials to worksite,paymentof royalty,all taxes etc.all complete as per PWD specification and direction of the Engineer-in-charge. |
| 958 | Supplying all materials, labour, T&P and providing cement plaster on brick/stone work including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc. all complete as per specification and direction of E.I.C.-12mm thick C.P with C.M. (1:6) |
| 959 | Bore Well Chamber- |
| 960 | Supplying all materials, labour, T&P and providing,fitting and fixing 100mm x 100mm x 100mm PVC Tee in wall including filling the recess with cement concrete (1:3:6) with 12mm size h.g chips all complete including watering, curing, conveyance of all materials to worksite, payment of royalty all complete as per specification anddirection of the Engineer in charge |
| 961 | Providing and fixing in position Polyproplene Foot steps of required shape and approved quality as per the direction of E.I.C. |
| 962 | Filling in foundation and plinth with excavated materials, moorum including watering and ramming as directed by the Engineer in charge |
| 963 | Supplying all materials, labour, T&P and fixing rotational moulded polyethylene cylindrical vertical waterstorage tank confirming to IS 12701- 1996 including cutting hole through the tank and fixing MS tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc. including hoisting the tankand placing the tankto the required position including all complete as per specification and direction of EIC.(including cost of 2000 liter capacity FG Over Head Tank) on roof of 1st Floor |
| 964 | Supplying all materials, labour, T&P and Construction of masonary stagging with providing 1st class KB. brick work in c.m, (1:6) of 0.46m. height in staging and in circular protection wall to support the tank in roof of ground floor using 25cm x 12cm x 8cm size KB. bricks having crushing strength not less than 75 kg/cm2 12mm thick c.p.(1:4) over brick work, R.C.C. Slab of size 1.64mtr xl.64mtr x0.l0mtr thick, R.C.C. beam of size 0.25m X 0.30m and 2.61m average length in c.c.(1:1.5:3) using 12mm size h.g. chips including centering and shuttering, watering, curing conveyance of all materials to work site etc. all complete as per specification and direction of E.I.C (2000 liter capacity FG Over Head Tank on roof of 1st Floor) |
| 965 | Providing and laying CERAMIC FLOOR TILESof premium grade and of approved size & shade in flooring on a bed of 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand) finished with flush pointing in white cement & pigment to match the shade of the tiles. |
| 966 | GroundFloor |
| 967 | First Floor |
| 968 | Supplying, fitting & fixing of Ceramic wall tiles of premium grade of size 300x200/200x200mm having thickness 6.5mm to 6.7mm confirming to IS 13753in dadoes, skirting and risers of stepslaid on 12 mm thick cement mortar (1:3) (1 cement : 3 course sand) jointed with slurry mixed with pigment to match the shades of the tiles etc. complete including cost of all materials, labour T&P etc. required for the work all complete as per direction of the Engineer-in-charge |
| 969 | GroundFloor |
| 970 | First Floor |
| 971 | Factory made GIRID FRP or called GRP sandwich compositedoor shutterof 32mm thick laminated with two GRP skin with good grain finishfabricated using UV stabilised isoppthalic gel coat and one layer of 450 gsm E-glass chopped strand mat (CSM) impregnated with ortopathilic resin The thickness of the skins shallnot be less than 1.50mm . Expanded polysryne ( EPS) structural foam panel of 29 mm tickness and a density of 20kg/cu.mts shall be used as core material wooden reinforcements made of sesasoned sal wood block of cross section not less than 28mm x 32mm and also necessary sal wood reinforcements for fitting the metal fittings such as lower bolts ,aldrops, handles etc. shall be provided . A structural adhesive compatible with (EPS)foam shall be used for bending the core material. the sal wood reinforcements and the skin The material and process for manufactuing te door shutter shallconform to RV -TIFAC components design centre\"s standards and specification and the door shutters tested in conformation to IS 4020-1998. The Finish of door shutter will be plain colour as per specificationand direction of the EngineerinCharge. etc. complete |
| 972 | ground floor and first floor |
| 973 | Factory made FRP( Altematly called GRP) door frame of size 75mm x 100mmfabricated using E - glass chopped strand mat (CSM) U.V stabilised inopathalic Gel coat and impregnated with inopathalic resin The thickness of the GRP skins shall not be less then 2.0 mm . The door frame consists of four segments which are provided with plug insocketarrrangement in-situ-in mould. The segments are plugged in and are joined together by means of srew. The GRP frame shall be provided with wooden reinforcement on six locations for high srew holding capacity for fixing metalic hold fast and shall be consolidated by filling with medium density foam / plaster of paris with fibre reinforcement , six number of 260mm x 25mm x 5mm size \"S\" shaped M.S flat holdfast shall be provided with the frame. The material and process for manufacturing the finish of door frame shall conform to RV-TIFAC composites Design centre\"s standards and specifications . The finish of door frame will be plain colour white /Ivory/Beige/Light grey / Golden brown / Mahogany/ Teak wood /sand stone Champagne/Pastel blue or any other colour using high quality pigment complete in all respect as per specification and direction of the Engineer in Charge.etc. complete |
| 974 | ground floor and first floor |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
