Municipal Adminitration And Water Supply Department-MAAWSD has published Tender For Providing Additional Amenities In Nehru Kalaiarangam Package -1 Providing Hvac System,Firefighting,Wall Partition And Interior Improvements. Submission Date for this Tender is 11-08-2023. HVAC Tenders in salem Tamil Nadu. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | CENTRALIZED AC |
| 2 | Supply, erection, testing and commissioning of 2.0 TR (6000 K. cal/ hr) ABSplasticsplittype Air conditioner conforming to IS: 1391 (Part-2) 1992 with Rotary compressor operating on refrigerant R-22/ Non - CFL suitable for wall mounting for operation on 230V, 50 HZ single phase AC supply withThree Star rating as per BEE specification andcapable of performing the functions of 1)Cooling 2)Dehumidifying 3)Air circulating 4)Filtering The installation works for the above split type A.C units includes the following. 1. Mounting / Fitting indoor and outdoor units at their respective locations. 2. Laying refrigerant pipe line of 6 meters distance, both units after drilling hole / holes in the wall if required. Thickness of the copper tubing shall not be less than 0.7mm. 3. Insulating the suction pipe with expanded polythene foam 5mm thick tubing. 4) Laying 15mm dia flexible PVC drain pipe of 6 mts. Length to throw out the condensate water being formed in the indoor unit. 5) Leak testing the entire gas unit. 6) Charging refrigerant gas in the unit. 7) Suitable electric wiring to be provided with 2.5sq.mm PVC insulated copper wire between indoor and outdoor units up to 4 meters length and up to switch within 3 meters of location of indoor unit. (Carrier/Voltas/O General Make only) |
| 3 | Supply and insttallation of 5KVA Capacity automatic Voltage stabiliser with Time delay relay (V.Guard or equaliant) SR |
| 4 | Supply and fixing of MS Stand for fixing outdoor unit(SR) |
| 5 | Supply and filling of R-22 Refrigerant gas. (SR)(For Split AC units) |
| 6 | Supply, Installation, Testing, Commissioning andHandling over of air cooled Unit of 25TR nominal capacity consisting of indoor unit complete with motor thermostatic expansion valve, drier, filter section and 2Nos of hermetically sealed power saving scroll compressor each with inbuilt internal thermal protector, internal pressure relief valve, HP cut out, LP cut out and outdoor unit consisting of condenser coils, fan motor etc.(SR) |
| 7 | Supply and fixing of 50 mm thick Anti Vibrating rubber pads(SR) |
| 8 | Supply and filling of R-22 Refrigerant gas. (SR) |
| 9 | Supply and fixing of flexible canvas connection between indoor unit and ducting.(SR) |
| 10 | Supply , Fabrication and erection of fabricated ducting made up of GI sheets of complete with MS angle supports angle flanges, anchor fastess, tees and bends where ever necessary etc as required. (SR) |
| 11 | 24 gauge Sheet |
| 12 | 22 gauge Sheet |
| 13 | 20 gauge Sheet |
| 14 | Supply, fabrication and Erection of Angle Frame for Ducting.(SR) |
| 15 | Supply and fixing of Duct mouth dampers.(SR) |
| 16 | Supply and providing acoustic for initial portion of ducting with 12mm thick fiber glass rigid board covered with tissue paper and aluminum perforated sheet (SR) |
| 17 | Supply and providing thermal insulation of 9mm thick vidoflex with aluminum foil.(SR) |
| 18 | Supply and fixing of extruded aluminium powder coated supply and retun air grills with volume control damper(SR) |
| 19 | Supply and fixing of water drain pipe line (1 inch PVC pipe)(SR) |
| 20 | Supply, and Laying of 30 sqmm Incoming cable for Power supply forAiconditioning unit.(SR) |
| 21 | Supply and providing Civil Concrete Block for Mounting the Roof Top Airconditioning Unit.(SR) |
| 22 | Supply and fixing of copper refrigerent piping of 7/8 inch Dia (SR) |
| 23 | FALSE CEILING |
| 24 | Supplying, fabricating, erecting and fixing Hilux (or) Equivalent Board False Ceiling upto a ceiling height of 4.5m from floor level (A) Using Hilux Board Plain Sheets (10mm thick) |
| 25 | FRONT ELEVATION |
| 26 | Providing and fixing structural glazing fabricated from roll formed section made of galvanised steel colour coated (Base steel as per IS 513 of "D" quality, galvanized as per IS 277 with Zinc of 120 gms/sqm) wit total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.60mm thick. Galvanised steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suuit wind pressures as given in IS 875. Paint specifications: Primer coat with epoxy Primer of 5-7microns thic, finish painted with a polyester paint of 12-16 micron tick and back coated with alkyd backer of 5-7 microns or poeder coated with pure polyester powder upto 50-60 microns thick. Dimensions: The section should be of 37x53 mm for frame vertical, 37x53mm for frame horizontal section and section for reinforcement should be of 31x55mm. glass holding section should be of 37x37mm for top and bottom grids in between should be of 37x18mm.(SOR 22-23, S.No: 266) |
| 27 | FIRE FIGHTING |
| 28 | Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental fficers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT (SOR 22-23, S.No: 386) |
| 29 | Supply and installation of CO2 type Fire Extinguisher of capacity 2kg confirms to IS 15683, bearing ISI mark, consisting of High Pressure seamless steel cylinder (IS 7285) and duly approved by Chief controller of Explosive Nagpur, fitted with wheel type valve, fully charged with CO2 gas (IS 15222), with non-conductor of electricity discharge PVC horn along with Bend Pipe, internally siphon tube, & mounting brackets having fire rating 21B. SOR 22-23, S.No: 387) |
| 30 | Supply and installation of Stored Pressure Mechanical Foam type Fire Extinguisher of Capacity 9 ltr Confirms to IS 15683, bearing ISI mark complete with brass forged squeeze grip type valve fitted with pressure gauge , pressurize with dry Nitrogen gas filled, with discharge nozzle with wall mounting bracket, having fire rating of 4A & 55B (Local rate) |
| 31 | Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers.SOR 22-23, S.No: 334) |
| 32 | Supply and fixing 4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle as directed by the Departmental Officers.SOR 22-23, S.No: XIII - Part-M(8E)) |
| 33 | Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT. SOR 22-23, S.No: 350) |
| 34 | Partition arrangements in first floor and Second floor |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
