Orissa Tourism Development Corporation Limited has published Tender For Renovation And Upgradation Of Way Side Amenity Centre At Chhuriapali In Bargarh Dist.. Submission Date for this Tender is 19-07-2023. Building Work Tenders in bargarh Odisha. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Dismantling and removing 2.5cm thick grading concrete from roof slab, cleaning the surface, lowering and removing the debris within 50m lead. |
| 2 | Providing 25mm thick grading concrete in C.C. (1:2:2) laid in proper slope over terrace roof slab by using two part of sand, one part of cement and two parts of6mm size black hard crusher broken granite chips with addition of water proofing compound of approved quality to be mixed with specified ratio including watering, curing, cost, conveyance, royalties of all materials, cost of all labour, T&P etc. complete as required for the finished item of work as directed by the Engineer-in-charge. |
| 3 | Removing old lime or cement plaster from walls including raking out joints 12mm deep and removing the debris within 50m lead. |
| 4 | Providing 12 mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) with portland slag cement (PSC) finished smooth to inside rough surface of brick masonry walls after racking out joints including watering and curing rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labour, T&P, sundries and scaffolding required for the work etc. with providing grooves as directed by the Engineer in charge. |
| 5 | Providing 16 mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) finished smooth to inside surface of brick masonry walls after racking out joints including watering and curing rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labour, T&P, sundries and scaffolding required for the work etc. with providing grooves as directed by the Engineer in charge. a)Ground Floor |
| 6 | Scraping old paint with scrapers, sand papering and washing with soap water or soda including scaffolding charges above 5M high and upto 8Mheight |
| 7 | Supplying, Diluting &SpreadingChemical Emulsion like CHLORPYRIPHOSOROther Chemical approved bythe Central Insecticides Board as directed by the manufacturer and spraying the mixtureuniformly bythe sprayer aspre-constructional Anti-termitetreatment and creating a chemical barrier under and around the column pits, wall trenches, basement excavation,top surface ofplinth filling, junction of walls and floorsalong with externalperimeter of thebuilding, expansion joints, surrounding the pipes and conduits etc. complete at the rate of 7.5 liters (or as directed by the manufacturer) per Each Sqm on vertical and 5.0 liters per Each Sqm on horizontal surfaces, 50% of the emulsion to be filled in center to center etc. complete as per the holes made in trenches at 150m.m IS:6313/1981(Part-II) completeincludingcost, conveyance, loading, unloading and taxes of all materials,cost of all labour, T&P, sundries and scaffoldingwhere required for the work etc.as directed by the Engineer -in -charge. ( The payment shall be made on the basis of theactual measurement of the plinth area of the building at Ground Floor and vertical faces will not be measured for payment). |
| 8 | Finishing wall surface with Acrylic wall putty of approved make and finished smooth and even surface to receive painting including cost of scaffolding staging charges with cost of all materials taxes, labour T & P etc complete as per direction of Engineer-in-charge. |
| 9 | Providing and painting two coats with plastic emulsion paint of approved quality and approved shade manufactured by reputed manufacture like NEROLAC /ASIAN /BERGER /DULOX or equivalent to make in all floors at all height by making the surface to the interior plastered surface of wall smooth with over of primer of approved quality including cost, conveyance, loading and unloading and taxes of all materials, cost of all labour, sundries, T & P, scaffolding etc. required for the work and complete in all respect as per specification and direction of Engineer-in-charge.a)Ground Floor |
| 10 | Wall painting two coats with 100% Acrylic emulsion paint (1st quality) exterior grade(weather coat) of approved make & shade manufactured by reputed manufacture like NEROLAC /ASIAN /BERGER /DULOX or equivalent to make an even finished surface over a coat of primer with water bond cement primer in all heights with all scaffolding and staging charges including cost, conveyance, taxes of all materials, cost of all labour, etc. complete as per specification and direction of Engineer-in-Charge |
| 11 | Providing and painting two coats with synthetic enamel paint of approved quality and approved shade confirming to ISI on iron work to give an even shade over a coat of primer of approved quality and shade including sand papering and making the surface smooth in all floors at all height with cost, conveyance, loading, unloading and taxes of all materials, cost of all labour, sundries, T& P scaffolding and taxes of all materials, cost of all labour, sundries, T & P scaffolding etc. required for the work andcomplete in all respect as directed by the Engineer-in-charge |
| 12 | KIOSK & STORE |
| 13 | Earthwork in excavation of foundation trenches in all kinds of soil including moorum stoney earth and earth mixed with boulders except sheet rock and boulders requiring blasting including dressing of sides and leveling the bed up to the required depth and depositing the excavated materials away from the work site with all leads and lifts, including shoring, shuttering and dewatering (if required) with cost of labour, hire & running charges of water pumps sundries & T&P required for the work complete as directed by the Engineer-in-charge. |
| 14 | Supplying and filling in foundation trenches and plinth, ditches with sand well-watered and rammed in layers not exceeding 23 cm. in depth with all lead and lift including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, sundries, T&P required for the work etc. complete in all respect as per specification and direction of Engineer-in-charge. (Measurement will be taken on finished compacted section only). |
| 15 | Providing & laying cement concrete of prop. (1:3:6) in foundation bed and floors using 40mm nominal size down graded, screened, washed hard black crusher broken granite metal of approved quality & from approved quarry including laying in the layers not exceeding 100 mm thick, hoisting, lowering, laying, watering and curing etc. complete to the required levels including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for the work complete and as per direction of Engineer-in-charge. |
| 16 | Brick work in foundation and plinth with flyash bricks in cement mortar (1:6) with best quality bricks having crushing strength not less than 75 Kg/cm2 immersing the bricks in water for not less than 6 hours before use (the bricks shall be well burnt, free from cracks, well shaped, uniform in size and shall produce a clear metallic ringing sound when struck) includes molding, chamfering, corbelling .complete as per drawing, design and specification, watering and curing for 7days including cost, conveyance, royalty and taxes of all materials, labour, T&P etc. and as per direction of Engineer in charge. |
| 17 | Brick work in Superstructure with flyash bricks in cement mortar (1:6) with best quality bricks having crushing strength not less than 75 Kg/cm2 immersing the bricks in water for not less than 6 hours before use (the bricks shall be well burnt, free from cracks, well shaped, uniform in size and shall produce a clear metallic ringing sound when struck) includes molding, chamfering, corbelling .complete as per drawing, design and specification, watering and curing for 7days including cost, conveyance, royalty and taxes of all materials, labour, T&P etc. and as per direction of Engineer in charge. |
| 18 | Providing, lifting, hoisting and laying Reinforced cement concrete of different RCC structure in foundation level ofM-20 grade as per approved designs and drawings having a minimum compressive strength (in work test) 200 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed andcleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portlandslag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position. |
| 19 | a) Foundation |
| 20 | b) Tie Beam - |
| 21 | Providing kota stone flooring using kota stone of approved quality, colour and size of 20mm minimum thick in floors, treads on steps and landings in all floors at all height on 20mm thick bed of cement mortar of mix (1:4) laid in proper slope and gradient with screened and washed sharp sand for mortar and grouted with neat white cement slurry jointing the kota stone with neat white cement slurry mixed with required quantities of pigments of approved marks to match the shades of the kota stone, if required , watering and curing for 21 days, including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, sundries, T&P required for the work including rubbing mechanically and wax polishing etc. complete in all respect as per specification and direction of Engineer-in-charge. |
| 22 | Providing 12mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) finished smooth to outside smooth surface of brick masonry walls after racking out the joints including watering and curing, rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labours, sundries, T&P and scaffolding required for the work etc. complete in all respect as desired by the Engineer in charge. |
| 23 | Wall painting two coats with 100% Acrylic emulsion paint (1st quality) exterior grade of approved make & shade manufactured by reputed manufacturer like NEROLAC / ASIAN / BERGER / DULOX or equivalent to make an even finished surface after cleaning by watering & removing the dirts etc. to the surface to be painted including watering, curing, cost, conveyance and taxes of all materials, cost of all labour, brushes, T&P etc. and necessary scaffolding work complete as directed by the Engineer-in-charge. |
| 24 | Providing, fixing and placing ofTor steel (HYSD) Fe-500(Make:SAIL/RINL/TISCON/JINDAL STEEL/SHYAM STEEL )for RCC work in all floors of required diameter of approved quality with straightening, Cutting, bending, bindingwelding or jointing if necessary, bending, binding, tying the grills as required for R.C.C. works, providing fan hooks where necessary and hoisting, lowering and placing in proper position according to approved designs and drawings including cost, conveyance, loading, unloading, taxes of M.S. rods or Tor steel and binding wires of 18 to 20 gauge required for the work and cost of all labour, sundries, T & P and scaffolding complete in all respect as directed by the Engineer-in-Charge ( payment will be made according to the actual weight of M.S rod /Tor steel consumed in the work and no separate payment will be made towards weight of binding wires which is to be borne by the contractor at his own cost of all labour, sundries, T & P and scaffolding complete in all respect as directed by the Engineer-in-Charge |
| 25 | Supplying and laying of heavy duty factory made hydraulically pressed and mechanically compacted pre-cast interlocking pavers of 80mm thick,preparation of sub base with 100mm sand and leveling,laying of interlocking paver block with sand binding and final compaction with plate vibrator finishing the surface including cutting of blocks at the edges with all labour and materials etc complete as per direction of Engineer-in-chrge. |
| 26 | LANDSCPAING |
| 27 | Supply of good garden soil and spreading uniformity in side landscape area up 1" height |
| 28 | Supply and Turfing of Zoysia grass carpet with well grown disease free, carpet formaed 2" thickness including loading and unloading and delivery at site and furting of greas carpet including watering, rolling as per requirement etc complete as per direction of Engineer -in-charge. |
| 29 | Supplying & Planting of Golden eypress 3"6" ht plants of well established , healthy, disease free type transprerted with poly bag including cost of transportatiion , loading /unloading etc, planting of each plant at specified location including cost of all labour for earth work, application of Manure/fertilizer/pestiside etc as per requirment etc complete in all respect as per th direction of the instruction of Engineer-in-charge. |
| 30 | Supplying & Planting of Ficus starlight 3"6" ht plants of well established, healthy, disease free type transported with poly bag including cost of trasportation loading/Unloaading etc, planting of each plant at specified location including cost of all labour for earth work, application of Manure/fertilzer/pesticide etc as per requirment etc complete in all respect as per the direction of the instructjionof Engineer-in-charge. |
| 31 | Supplying & Planting of Ficus Panda 3"6" ht plants of well established, healthy , diseses free type transported with poly bag including cost of trasportation, loadign/Unloading tec, planting of each plant at specified location including cost of all labour for earth work, application of Manure/fertilizer/pesticide etc as per requirment etc complete in all respect as per the direction of the instruction of Engineer-in-charge. |
| 32 | Supplying & Planting of Syzygium 4" ht plants of well established, heathy, disease free type transported with ply bag including cost of all labour for earth work, application of Manure/fertilizer/pesticide etc as per requirment etc complete in all respect as per the direction of the instruction of Engineer-in-charge. |
| 33 | Supplying & Planting of Sampen palm 5"ht plants of well established , healthy, disease free type transported with poly bag including cost of transportatio, cost of all labour for earth work, application of etc complete in all respect as per the direction of the instruction of Engineer-in-charge. |
| 34 | PH |
| 35 | Supplying all materials, labor T&P for fitting and fixing in all floors" fixed type glass mirror of size 600mm x 450mm best INDIAN make of 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with chromium plated brass screws and washer completeas per specification and direction of Engineering-in-charge. |
| 36 | Supplying & FixingBib cockofCP brass of Jaquar continetnal cat no- Jaquar CON-047KN/ eqv of crabtree / lauretincluding making good the damages including tools, plant, all material,labour , scaffolding etc. complete. |
| 37 | Supplying all materials, labour, T&P and fixing standard sized 15mm dia Angular Stop cock of Jaquar Cat. No.- COP-057PM or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 38 | Supplying & Fixingconcealed stop cockofCP brass (Jaquar cat no-CON-069 , continental / eqv of crabtree / lauret)including making good the damages including tools, plant, all material,labour , scaffolding etc. complete. |
| 39 | Supplying all materials, labour, T&P and fixing standard sizedCP Soap dish holder of Jaquar Cat. No.-CAN-1131N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 40 | Supplying all materials, labour, T&P and fixing standard sized C.P towel rail of Jaquar Cat. No.-1111BNM or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 41 | Providing and fixing C.P. Glass shelf 600mm long of Jaquar Cat. No.-ACN-1171N or equivalent type of approved make fixed to wall including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 42 | Supplying all materials, labour, T&P and fixing standard sized pillar cock of Jaquar Cat. No.-FUS-29001 or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 43 | Providing and fixingcircular type stainless steeljalli (grating) with hole for floor /nahani trap etc complete as per PH specification and direction of the engineer in charge |
| 44 | Supplying all materials, labour, T&P and fixing health faucet of Jaquar Cat. No.- ALD 573 or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 45 | Supplying all materials, labour, T&P and fixing standard two Way Bib cock of Jaquar Cat. No.- COP-041PMor equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 46 | Supplying all materials, labour, T&P, fitting and fixingUPVC SWR pipes & fittings of approved make confiEach Each Rmtting to IS-4985:2000, both below and above ground level / floor and on walls including supply of bobbins, nains, screws, wooden cleats, pipe clips as per requirement, including earth work in excavation and fitting, including cuting walls and floor and making good the damages with cement concrete (1:2:4) with hard granite chips, incluidng scaffolding wherever necessary all complete as per the PH specification and direction of the Engineer-in-charge.(Make SUPREME /ORIPLAST ) |
| 47 | 110mm dia |
| 48 | 75mm dia |
| 49 | Supplying all materials, labour, T&P, fitting and fixingCPVC SWR pipes & fittings of approved make |
| 50 | 20mm dia |
| 51 | 15mm dia |
| 52 | Electrical works |
| 53 | Recessed Wiring to light/ Fan/ Exhaust Fan point in 5/8" or 3/4"dia. Good quality PVC pipe with 1.5 sq.mm PVC insulated Cu.wire (2 run) &1.0 sq.mmPVC insulated Cu.wire (1 run) for running earth complete with 1 no .6Amp.1way plate type Modular switch, (Polycarbonate)and G.I box of adequate size including PVC bend, saddle, elbow, etc and other necessary materials & labour complete as per the direction of Engineer-in-Charge. |
| 54 | Group -A |
| 55 | Group -B |
| 56 | Group -C |
| 57 | Recessed Wiring to light/ Fan point in 5/8" or 3/4"dia. Good quality PVC pipe with 1.5 sq.mm PVC insulated Cu.wire (2 run) &1.0 sq.mmPVC insulated Cu.wire (1 run) for running earth complete with 1 no .6Amp. 2 way plate type Modular switch, (Polycarbonate)and G.I box of adequate size including PVC bend, saddle, elbow, etc and other necessary materials & labour complete as per the direction of Engineer-in-Charge. |
| 58 | Point wiring for 5 / 6 amp socket outlet with 2 x 1.5 sq.mm FR PVC insulated single core multistrand copperconductor of ISI marked in recess 20 mm dia non-metalic PVC flexible conduit with modular type switch ,phenolic laminated sheet suitable size ISI marked MS box and earthing point with 1 x 1.5 sq.mm FR PVCinsulated single core multistrand copper conductor for loop earthing etc. as required. ( Make of wire Finolex /L&T / Anchor / Havels / V Guard/RR ) |
| 59 | Supply and fixing of 6A modular switch & socket outlet complete with 1 no of 240 volt 6 amp 5 pin universal round/flat pin combined shuttered socket outlet & 1 no. of240 volt 6 amp control switch mounted on modular grid plate, all housed in a 3 module recessed zinc chromate passivated flush metalbox including mosaic white cover plate of approved make with all other accessories etc. as required complete as per the direction of Engineer-in-Charge. |
| 60 | Supply and fixing of 6A modular switch & socket outlet complete with 2 no of 240 volt 6 amp 5 pin universal round/flat pin combined shuttered socket outlet & 2 no. of240 volt 6 amp control switch mounted on modular grid plate, all housed in a 3 module recessed zinc chromate passivated flush metalbox including mosaic white cover plate of approved make with all other accessories etc. as required complete as per the direction of Engineer-in-Charge.( Make of Switch & Socket - L&T / Anchor roma / Havells / Legrand ) |
| 61 | Supply and fixing of 16A modular switch & socket outlet complete with 1 no of240 volt 16 amp 5 pin universal round/flat pin combined shuttered socket outlet &240 volt 16 amp control switch mounted on modular grid plate, all housed in a 3 module recessed zinc chromate passivated flush metalbox including mosaic white cover plate of approved make with all other accessories etc.as required. as per the direction of Engineer-in-Charge.( |
| 62 | Supplying and fixing of metal box of 32A D.P modular switch on surface or inrecess with 2 Madular metal box with cover in front including providing and fixing, connection etc as required as per the direction of Engineer-in-Charge. |
| 63 | Supplying and fixing of metal box of 20A modular socket on surface or inrecess with 2 Madular metal box with cover in front including providing and fixing, connection etc as required as per the direction of Engineer-in-Charge. |
| 64 | Supply and fixing of capacitor switching circuit,works at 120 to 280 volts,Heavy duty, Noiseless 100W step type Fan regulator complete with all other necessary materials & labour. |
| 65 | Supply and fixing ofTV antennaSocket outlet completelyproviding 1 no. of TV antenna socket & Top , moulded case metal box & plate of adequate size includingPVC bend, saddle, elbow, etc. & other necessary materials &labour complete as per the direction of Engineer-in-Charge. complete as per the direction of Engineer-in-Charge.( Make of Switch & Socket - L&T / Anchor roma / Havels / Legrand ) |
| 66 | Supply and fixing of Telephone point completelyproviding1 no.of telephone socket & Top, Metal plate made of polycarbonate moulded casemetal box with metal plate of adequate size including PVC bend, saddle, elbow etc and othernecessary materials & labour complete as per the direction of Engineer-in-Charge.complete as per the direction of Engineer-in-Charge. ( Make of Switch & Socket - L&T / Anchor roma / Havels / Legrand ) |
| 67 | Sub-main wiringin20/25/32mm dia. good quality ISI mark PVC Conduit withfollowing sizes PVC insulated un-sheathed Single Core FRLS Cu. conductor wire of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. |
| 68 | (2 x 1.5 + 1 x 1.5) sq.mm copper wire |
| 69 | (2 x 2.5 + 1 x 1.5) sq.mm copper wire |
| 70 | (2 x 4 + 1 x 2.5) sq.mm copper wire |
| 71 | (2 x 6 + 1 x 2.5) sq.mm copper wire |
| 72 | (4 x 4 + 1 x 2.5 ) sq.mm copper wire |
| 73 | (4 x 6 + 1 x 2.5 ) sq.mm copper wire |
| 74 | 0.5mm 2 pair telephone wire |
| 75 | RJ-6 Coaxial TV wire |
| 76 | Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe with charcole / coke and salt etc. as required as per the direction of Engineer-in-Charge. |
| 77 | Supplying and laying 10 Sq mm copper conductor ISI marked at 0.5 meter below grond level as strip earth electrode including soldering etc. as required as per the direction of Engineer-in-Charge. |
| 78 | Supply & fixing of 12 way Single pole and Neutral sheet steel MCB double door distribution box complete with tinned copper busbar, neutral link, earth bar, din rail, detachable gland plate includingcommissioning including all other materials etc. as required as per the direction of Engineer-in-Charg. |
| 79 | Supply & fixing of 4 way Triple pole and Neutral sheet steel MCB double door distribution box complete with tinned copper busbar, neutral link, earth bar, din rail, detachable gland plate includingcommissioning including all other materials etc. as required as per the direction of Engineer-in-Charg. |
| 80 | Supply & fixing of 4 way Triple pole and Neutral vertical double door load line distribution board complete with tinned copper busbar, neutral link, earth bar, din rail, detachable gland plate includingcommissioning including all other materials etc. as required. |
| 81 | Supply and fixing of 5 amp to 32 amp rating 240 V "B" series single pole miniature circuit breaker suitable for lighting and other loadsin the existing MCB DB ISI marked complete with connections testing and commissioning etc. as required. |
| 82 | Supply and fixing of 40 amp DP miniature circuit breaker suitable for inductive loads in the existing MCB DB ISI marked complete with connections testing and commissioning etc. as required. |
| 83 | Supply and fixing of 63 amp TPN miniature circuit breaker suitable for inductive loads in the existing MCB DB ISI marked complete with connections testing and commissioning etc. as required. |
| 84 | Supply and fixing of 63 amp TP miniature circuit breaker suitable for inductive loads in the existing MCB DB ISI marked complete with connections testing and commissioning etc. as required. |
| 85 | Supply and fixing of 63/100 Amp 4 pole MCCB of approved make with all other accessories etc as required complete as per the direction of Engineer-in-Charge. |
| 86 | Supply, Installation, Testing, and commissioning of decorative ceiling fan 900/1200 mm sweep 230/250 volts, 50HZ complete with suitable, clamp, downrod (as per site requirement), blades, canpoy,rubber, shackle, and connections with 1.5 sq.mm PVC insulated copper conductor cable etc as required of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 87 | Supply, Installation, Testing, and commissioning of ventilating Plastic Body Exhaust fan 150 mm dia suitable to work on 230/250 volts, 50HZ complete with mounting frame and louvers including making the hole to suit the size of above fan, making good the damage, connections, with 1.5 sq.mm PVC insulated, copper conductor, single core cable etc as required of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 88 | Supply, Installation, Testing, and commissioning of ventilating metal Body Exhaust fan 150 mm dia suitable to work on 230/250 volts, 50HZ complete with mounting frame and louvers including making the hole to suit the size of above fan, making good the damage, connections, with 1.5 sq.mm PVC insulated, copper conductor, single core cable etc as required of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 89 | Supply, Installation,Testing & commissioning ofSurface mounting 18 W LED tube light fitting includingluminairs of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 90 | Supply, Installation,Testing & commissioning ofSurface mounting 9 W LED tube light fitting includingluminairs of approved make complete with all materials & labour. |
| 91 | Supply, Installation,Testing & commissioning ofSurface mounted Celing 9 watt LED luminariessuitablefor indoor applications of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 92 | Supply, Installation,Testing & commissioning ofSurface mounted Celing 18 watt LED luminariessuitablefor indoor applications of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 93 | Supply, Installation,Testing & commissioning ofRecessed mounted 3 watt LED spot luminaries suitable for indoor applications of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 94 | Supply, Installation,Testing & commissioning ofRecessed mountedCeling 9 watt LED luminaries suitablefor indoor applications of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 95 | Supply, Installation,Testing & commissioning ofRecessed mountedCeling 12 watt LED luminaries suitablefor indoor applications of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 96 | Supply, Installation,Testing & commissioning ofFlexibleLEDstripwide viewing angle for good light distribution & IP 65 protection, linkable and easy to install, complete with separate replaceable electronic driver approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 97 | Supply and installation of surface mounted IP 65 LED Bulk head luminaries of 10 W Capacity of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 98 | Supplying, storing, laying, testing and commissioning of 2c x 6 Sq. mm A2XFY Al armoured Cable1100 Voltsetc. as required of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 99 | Supplying, storing, laying, testing and commissioning of 4 c x 10 Sq. mm A2XFY Al armoured Cable1100 Voltsetc. as required of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 100 | Supplying, storing, laying, testing and commissioning of 3.5 c x 35 Sq. mm A2XFY Al armoured Cable1100 Voltsetc. as required of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 101 | Supplying, storing, laying, testing and commissioning of 3c x 2.5 Sq. mm A2XFY flexible copper conductor etc as required of approved make complete with all materials & labour of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 102 | Supply, installation, testing & commissioning of 3050 mm long decorative lighting pole with mild steel body step pole with grey/black powder coting fnish. The control gear tray made up off diecast alluminium body & prewired with 2.5 sqmm copper cable, 6 Amp SP MCB, 32 Amp 4 pole connector, 5 Amp 3 way terminal connector & earthing point. The Pole shall have base Plate of size (200x12) mm with provision for founation bolt fittings.Compatible for all suitable size for cable entry & exist as required of approved make with all materials & labour as per the direction of Engineer-in-Charge.(Make: K- Lite Flat Series KP-4786/ Havells / BAJAJ/CG/Jaquar). |
| 103 | Supply, installation, testing & commissioning of coil earthing etc as required as per the direction of Engineer-in-Charge. |
| 104 | Supply, installation, testing & commissioning of 30 watt LED post top light fittings integrated with LED Modules, Clear Polycarbonate optical cover, Protection class IP 65, Integral power supply, Earth connection, BIS Mark as required of approved make etc complete with all materials & labour as per the direction of Engineer-in-Charge. (Make: K -lite Avira KL- 4976/ Havells / BAJAJ/CG/Jaquar). |
| 105 | Supplying, installation and commissioning of 8W LED Bollard light. New generation, energy saving, environmental friendly, long life aesthetically designed aluminium landscape IP 65 Led 8 watt luminaire for diffused lighting with high power LED as light source etc complete with connection as required for the work and as per direction of Engineer-in-Charge.(Make: Havells /K- Lite/ BAJAJ/ CG/Jaquar). |
| 106 | Supplying, installation and commissioning of 35W LED post top light luminaries having Versatile pressure die-cast aluminium IP66 with high power LED as light source to be fixed on the ends of pole etc complete with connection as required for the work and as per direction of Engineer-in-Charge.(Make: Havells Ruby /K- Lite/ BAJAJ/ CG/Jaquar). |
| 107 | Supply, installation, testing & commissioning of Hot dipGalvanized 8 mtr long Octagonal poles with base plate fabricated from special steel plates as per BSEN 10025/IS 5986 single section Top Dia: 70mm, Bottom Dia:130 mm, Sheet Thickness:3, base plate size :200*200*16mm with foundation base plate of size 250 mm x 250mm x 16mm thick Hot Dip Galvanization of both internal and external surface with minimum thickness of 86 Microns more that 600 gm/ sqm as per IS: 4759 specification. 1mtrlong(Galvanized ) single arm bracket made out of 60 mm outer diameter Hot dip tubular pipesand welded to fit the top of the above pole and Plate for rigidity between cap and pipe with provision of passing the electrical cable from the pole to the end of the arm for connection of the luminaries, with provison of Electrical Termination junction in side the pole at a height of 1mtr(maximum) from the bottom of pole, with clamps, 4way 100Amps / 400Volts connector, 6/10 Amps / 230 Volts / 10KA SP MCB, Cable gland at bottom of suitable size for cable entry & exist. |
| 108 | Supply, installation, testing & commissioning ofIP 65 LED street Light of 90 W Capacity 6000K Colour temperature with pressure die-cast Aluminium body havingin built electronic driver which have 50000 burning hour road way luminaries of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 109 | Supply, installation, testing & commissioning ofIP 65 LED flood Light of 200 W Capacity 6000K Colour temperature with pressure die-cast Aluminium body havingin built electronic driver which have 50000 burning hour road way luminaries of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 110 | Supply, installation, testing & commissioning of LED spike light Environmental friendly, compact, light weight, energy saving, IP66 LED spike light.Multi purpose application like column lighting, tree up-lighting, statue accentuation etc. can be addressed with ease.of approved make etc complete with all materials & labour as required as per the direction of Engineer-in-Charge.(Make:Havells Eros/ K Lite/ BAJAJ/CG/Jaquar). |
| 111 | Supply, installation, testing & commissioning of Main pannel board2mm thick C.R. sheet individual box GI angle frame febricated welded hinges, powder coated body & danger board. Incoming 160 Amp 4 pole MCCB 1 no, 200A TPN copper bus bar-1 Set,indicator lamp, struggle switch & fuses -3 Nos. Digital voltage current meter -1 No., 100/5A CT coil-3 Nos., 63 Amp Change over 1 no, 63/100 Amp MCCB 5 nos, 40 Amp DP MCB 2nos,40 Amp TPN MCB 2nos& wire for wiring of approved make etc complete with all materials, labour &transportation as required as per the direction of Engineer-in-Charge. |
| 112 | R.C.C. work ofM-20having minimum compressive strength of 200kg./cm2 in 15cm cubes at 28 days and in accordance with I.S. 456 and I.S. 516 using crusher broken hard black granite chips of approved quality & from approved quarry including hoisting, lowering, laying and compacting concrete with vibrator, watering and curing for 28 days, cost of rigid and smooth including centering & shuttering and finishing to exposed surface smooth providing, grooves or beads wherever necessary including cost, conveyance & royaltiesof all materials and cost of all labour, T&P etc. as required for the work complete in all respects as per drawing, design and direction of Engineer-in-charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
