}

Tender For Repair And Maintenance Of Dg Sets, Amf Panels, Fire Fighting And Fire Alarm System, Lt Acb, Ats, Apfc Panels And Servo Stabilizers At Ins Valsura, Jamnagar, jamnagar-Gujarat

Military Engineer Services-MES has published Tender For Repair And Maintenance Of Dg Sets, Amf Panels, Fire Fighting And Fire Alarm System, Lt Acb, Ats, Apfc Panels And Servo Stabilizers At Ins Valsura, Jamnagar. Submission Date for this Tender is 14-08-2023. Alarm Systems Tenders in jamnagar Gujarat. Bidders can get complete Tender details and download the document.




Tender Notice

38395213
Corrigendum : Tender For Repair And Maintenance Of Dg Sets, Amf Panels, Fire Fighting And Fire Alarm System, Lt Acb, Ats, Apfc Panels And Servo Stabilizers At Ins Valsura, Jamnagar
Open Tender
Indian
Gujarat
jamnagar
14-08-2023

Tender Details

Repair And Maintenance Of Dg Sets, Amf Panels, Fire Fighting And Fire Alarm System, Lt Acb, Ats, Apfc Panels And Servo Stabilizers At Ins Valsura, Jamnagar

Corrigendum Details

Sr No CorrigendumDate Corrignedum CorrigendumType NewSubmissionDate
1 07-Jul-2023 Date Corrigendum Date 27-07-2023
2 17-Jul-2023 Date Corrigendum II Date 02-08-2023
3 17-Jul-2023 BOQ Corrigendum BOQ 02-08-2023
4 02-Aug-2023 Bid Auto Extn Corrigendum Bid Auto Extn Corrigendum 09-08-2023
5 09-Aug-2023 Bid Auto Extn Corrigendum Bid Auto Extn Corrigendum 14-08-2023

Key Value

Document Fees
INR 500 /-
EMD
INR 90000.0 /-
Tender Value
INR 45 Lakhs /-

BOQ Items

Name of Work: Repair and maintenance of DG Sets, AMF Panels, Fire Fighting and Fire Alarm System, LT ACB, ATS, APFC Panels and Servo Stabilizers at INS Valsura, Jamnagar
Sl. No. Item Description
1M&L to attend "B" check for DG set of capacity 63 kVA (Make:Greaves) at different locations to carry out maintenance/servicing as given below once during the contract period as ordered including testing on completion of the following all as directed:- (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer,Contactors, Meters and others etc. (ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/ silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning. (xii) Change of Air filter element with O ring. (xiii) Change of filter insert with O ring (xiv) Change of Lub oil filter. (xv) Change of Primary filter element. (xvi) Change of secondary filter element. (xvii) Change of greaves lub oil CI4- 10ltrs pack (xviii) Change of Radiator pre-mix greaves kOOL 10 ltrs, complete to the satisfaction of Engr -in-charge. (Note: Cost of New minor spares required for replacement to make the DG set fully functional is included in quoted rate.)
2All same as per serial item No. 1 here-in-above, but DG set of capacity 100 kVA Make: Greaves
3All same as per serial item No. 1 here-in-above, but twice during the contract period and change of greaves Lub oil CI4- 20Ltrs pack complete for DG set of capacity 160 kVA Make: Greaves
4All same as per serial item No. 1 here-in-above, but twice during the contract period and change of greaves Lub oil CI4- 20Ltrs pack complete for DG set of capacity 250 kVA Make: Greaves
5All same as per serial item No. 1 here-in-above, but twice during the contract period and change of Cummins Lub oil CI4- 20Ltrs pack complete for DG set of capacity 160 kVA Make: Jakson
6M&L and attend "B" check for DG set of capacity 15 kVA (Make: Kirloskar) at different locations to carry out maintenance/servicing as given below once during the contract period as & when ordered including testing on completion of the following all as directed (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer, Contactors, Meters and others etc.(ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/ silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging, Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning (xii) Change of Spinon Lub oil filter (xiii) Change of air cleaner element (xiv) change of Belt- AVX 10 1500 (xv) Change of fuel filter element (xvi) Change of KOEL care premium genuine oil 7.5Ltrs Can, complete all as specified and directed by Engr-in-charge. (Note: Cost of New spares required for replacement is included and no seperate payment for minor spares if any reqd, will be made on this account to contractor.)
7All same as per serial item No. 6 here-in-above, but change of V Belt cogged- AVX10 1265L blower pulley, Change of V Belt cogged-AVX10 1136 for alternator pulley and Change of KOEL care premium genuine oil 13Ltrs Can, complete for DG set of capacity 40 kVA Make: Kirloskar
8M&L and attend "C" check for DG set of capacity 63 kVA (Make: Greaves) at different locations to carry out maintenance/servicing as given below once during the contract period as & when ordered including testing on completion of the following all as directed: (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer, Contactors, Meters and others etc. (ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii)Check exhaust pipe, flange and lagging Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning (xii) Change of Gskt set 4G11TA (w/o Hd gskt) (xiii) Change of cogged belt AX43-1143L (xiv) change of pipe turbo oil supply (xv) Change of pipe turbo drain (xvi) Change of set of hoses for 4G valve (xvii) Change of setting screw (xviii) Change of hex nut M8x1 DIN934 (xix) Change of gasket for PDC rocker cover (xx) Change of set of flex F/P (xxi) Change of push rod. (Note: Cost of New spares required for replacement is included and no seperate payment for minor spares if any reqd will be made on this account to contractor.)
9All same as per serial item No. 8 here-in-above, but DG set of capacity 100 kVA Make: Greaves
10M&L and attend "C" check for DG set of capacity 15 kVA (Make: Kirloskar) at different locations to carry out maintenance/servicing as given below once during the contract period as & when ordered including testing on completion of the following all as directed:(i) Check and clean engine,alternator battery,instrument panel,AMF panel,Timer,Contactors,Meters and others etc. (ii) Tightening of all nuts& bolts of DG set and its accessories.(iii)Check for any diesel lekage from any point and rectify if observed.(iv) Check and adjust fan belt tension ,replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/silencer,Repair if required. (vi)Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii)Check and tighten the AVM pads nuts and bolts,change AVM pads if found damaged. (viii)Check exhaust pipe,flange and lagging Repair if found damaged. (ix) Check output of alternator ,if found OK adjust the same to specified values in case of brush type.(x) Checking of all hoses and cleanup, if required. (xi)Oiling,Greasing and checking for proper & smooth functioning(xii) Change of rocker cover gasket (xiii) Change of valve seat insert inlet & exhaust (xiv) change of valve pair inlet & exhaust (xv) Change of set of joints (xvi) Change of set of O rings HA294 (xvii) Change of intermediate ring 1.1mm (xviii) Change of valve guide (xix) Change of valve stem seal , complete all as specified and directed by Engr -in-charge. (note :- Cost of New spares required for replacement is included and no seperate payment for minor spares if any reqd, will be made on this account to contractor. )
11All same as per serial item No. 10 here-in-above, but for DG set of capacity 40 kVA Make: Kirloskar
12S&F in repairs set of hoses with clipsfor DG set of capacity 63/ 100 kVA Make: Greaves
13S&F in repairs set of fuel pipes for DG set of capacity 63/ 100 kVA Make: Greaves
14S&F in repairs set of injector pipes for DG set of capacity 63/ 100 kVA Make: Greaves
15S&F in repairs Exhaust silencer for DG set of capacity 63/ 100 kVA Make: Greaves
16S&F in repairs injector with nozzle for DG set of capacity 63/ 100 kVA Make: Greaves
17M&L for greaves lubricating oil SAE 15W40 suitable for DG Set.
18M&L for Coolant suitable for DG sets make Fleetguard, Valvoline, Premium
19S&F in repairs Air filter outer for DG set of capacity 63/ 100 kVA Make: Greaves
20S&F in repairs Air filter inner for DG set of capacity 63/ 100 kVA Make: Greaves
21S&F in repairs 12V temp guage (40-120 deg cel) for DG set of capacity 63/ 100 kVA Make: Greaves
22S&F in repairs 12V press guage, 0-10 bar for DG set of capacity 63/ 100 kVA Make: Greaves
23Servicing and caliberation of FIP (Fuel injection pump) & nozzles including replacement of minor parts like nuts,bolts,washers etc of following :-DG Set 63/100 KVA capacity
24M&L for taking out Radiator of DG set 63 kVA/100 kVA Make: Greaves for repair, welding, brazing, leak testing & refixing to DG set to its original position and testing complete all as directed.
25M&L for taking out Radiator of DG set 160 kVA/250 kVA Make: Greaves for repair, welding, brazing, leak testing & refixing to DG set to its original position and testing complete all as directed.
26M&L for taking out Radiator of DG set 160 kVA Make: Jakson for repair, welding, brazing, leak testing & refixing to DG set to its original position and testing complete all as directed.
27Servicing & repair to self starter of DG set of capacity 15/40 kVA (Make: Kirloskar) including replacement of parts such as washer, nut, bolts, bush, solenoid, rotor etc. assembling and testing complete.
28All same as per serial item No. 27 here-in-above, but for DG set of capacity 63/100 kVA Make: Greaves
29All same as per serial item No. 27 here-in-above, but for DG set of capacity 160/250 kVA Make: Greaves
30All same as per serial item No. 27 here-in-above, but for DG set of capacity 160 kVA Make: Jakson
31S&F in repair Solonid Switch for 15/ 40 kVA DG set Make: Kirlosakar and testing complete for proper functioning.
32S&F in repair Solonid Switch for 63/ 100 kVA DG set Make: Greaves and testing complete for proper functioning.
33S&F in repair Relay card for 15/ 40 kVA DG set Make: Kirlosakar and testing complete for proper functioning.
34S&F in repair Relay card for 63/ 100 kVA DG set Make: Greaves and testing complete for proper functioning.
35S&F in repair Solonid Switch for 160/250 kVA DG set Make: Greaves and testing complete for proper functioning.
36S&F in repair AVR suitable for 15 kVA DG Set complete all as directed.
37S&F in repair AVR suitable for 40 KVA DG Set complete all as directed.
38S&F in repair AVR suitable for 63 KVA DG Set complete all as directed.
39S&F in repair AVR suitable for 100 KVA DG Set complete all as directed.
40S&F in repair AVR suitable for 160 KVA DG Set complete all as directed.
41S&F in repair AVR suitable for 250 KVA DG Set complete all as directed.
42S&F in repair battery auto cable copper PVC insulated unsheathed 35 Sqmm single core copper cable complete.
43S&F in repair battery auto cable copper PVC insulated unsheathed 95 sqmm single core copper cable complete.
44S&F 90AH 12Volt Lead acid battery (Maintenance free battery with min 2 years warranty) for DG set. Make: Exide Xpress
45S&F 150AH 12Volt 12Volt Lead acid battery (Maintenance free battery with min 2 years warranty) for DG set. Make: Exide Gold
46S&F battery lugs for DG set battery complete all as directed by Engr in charge.
47S&F in repair Ignition Switch of DG Sets complete all as directed.
48S&F in repair No volt coil for contactor of capacity up to 200 Amp Capacity all as specified and as directed by EIC. Make : L&T /C&S/Schneider
49S&F in repair LED type pilot lamp.Make: C&S / L&T
50S&F in repair selector switchin existing panel all as directed.
51S&F in repair Volt meter 0-500Volt in existing panel includingwiring from bus bar to volt meter terminalsiand fix the wiring wit existing control wiring all as directed. Make: L&T/ Meco/ HPL
52S&F in repair Ammeter 0-100 Amp in existing panel with necessary wiring from CT to Ammeter and fix the wiring in existing set of control wiring all as directed. Make: L&T/ Meco/ HPL
53S&F in repair Ammeter 0-200 Amp in existing panel with necessary wiring from CT to Ammeter and fix the wiring in existing set of control wiring all as directed. Make: L&T/ Meco/ HPL
54S&F in repair electronic timer of215/240/360/415 Volt 3 to 120 Sec all as directed. Make: L&T/C&S/Schneider
55M&L for wiring loom of control panel of DG Set AMF panel from Relay and auxilliary contacts complete by using 2.5 sq.mm copper cable of colour code from auxilliary contacts to Realyincluding fault finding etc all as specified and as directed.
56M&L for Overhauling of water pump with repairing kit for 63/100 kVA DG set complete all as directed.
57M&L for Overhauling of water pump with repairing kit for 160/250 kVA DG set complete all as directed.
58M&L for complete checking of AMF panel,finding the fault, servicing complete including replacement of unserviceable spares and testing complete for manual & Auto operations all as directed. Note: Supply only of new items required for replacement will be measured & paid seperately under respective item of schedule.
59Supply only AMF Relay.
60Supply only single phase preventor.
61Supply only PLA relay.
62Supply only 3 pole power Contractor ML-4, 70 A, 415 V. Make: L&T/Legrand
63Supply only 3 pole power Contractor ML-4, 163 A, 415 V. Make: L&T/Legrand
64S&F in repair HRC Fuse base of capacity 200 Amps.
65S&F in repair Anti vibration pad set suitable for 63/ 100kVA DG set all as directed.
66M&L for taking out alternator of DG set of capacity 15 kVA (Make: Kirloskar) by dismantling from engine pulley including disconnecting electrical connection complete & transporting to workshop. Opening the rotor and stator for rewinding with copper wire of existing guage and then revarnishing the stator & rotor with good quality varnish, Heating and baking complete upto requisite duration. Check bearing & shaft for machining if reqd. Re-assemble stator & rotor by replacing existing bearings with new bearings complete. Retransportation alternator to base and coupled with engine by using new rubber bushing spider, nutbolts complete. Testing the system for smooth functioning & checking current and load output by giving existing electrical load and to the entire satisfaction of engr in charge.
67All same as per serial item No. 66 here-in-above, but for DG set of capacity 40 kVA Make: Kirloskar
68All same as per serial item No. 66 here-in-above, but for DG set of capacity 63 kVA Make: Greaves
69All same as per serial item No. 66 here-in-above, but for DG set of capacity 100 kVA Make: Greaves
70M&L for Readymade electrolyte having specific gravity 1.4 for DG set of any capacity all as directed.
71M&L for Distilled water having specific gravity 1.0 for DG set of any capacity all as directed.
72S&F in repair outdoor type double door factory fabricated 3.00 thick CRCA sheet front opening with Aluminium bus bar switch gear and all requisite internal fittins/ fixtures suitable for 63 kVA DG Set, 3 Phase, 50 Hz, 1500 RPM of Make Greaves (Engine sl No. 12080480408, alternator Sl No. 08L33889) complete all as specified and as directed by Engineer-in-Charge.
73S&F in repair MCCB thermal magnetic protection unit rating 160 Amp, 4 pole, 25 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and ncluding necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items complete all as specified. Make:Legrand Cat No. 4200 57 or equivalent in makes mentioned in Appendix "B" here-in-after.
74S&F in repair MCCB thermal magnetic protection unit rating 100 Amp, 4 pole, 25 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and ncluding necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items complete all as specified. Make:Legrand Cat No. 4200 55 or equivalent in makes mentioned in Appendix "B" here-in-after.
75Sevicing, repair, maintenance and attending complaint/ faults to the Fire Fighting and Fire alarm system including Fire Alarm Control Panel, Pre Alarm Action, Programmable detector sensivity, Device type verification, Earth fault annuciation facility at 0 ohms, Double Address Sensing, Loop wise divice test, 40 x 4 Characters LCD display 2 numbers of loop card and 200 devices in any combination per loop. Day/ Night Mode facility, USB 2.0 interface for PC connetivity RS 485 Communication facility for network/ Repeater/ MODBUS/ BACnet. Programmable Auto Silence Facility, Programmable AC Loos delay. Programmable Silence Inhibit. Two Nos. of programmable inputs, Battery low audio, visual warning, Three programmable Form C relay for Fire, Fault and Supervisory maintenance complete all as directed. Note: (i) New spare parts will be measured and paid separetely.
76Supply, installation, commissioning and testing of Analogue Addressable Fire Alarm Control Panel including detector wise configuration facility 2000 Event Storage with Real Time Clock, Upto 192 grouping facility, Pre Alarm Action, Programmable detector sensitivity. Device type verification, Earth fault annunciation facility at 0 ohms, Double Address Sensing, Loop wise device test. 40 X 4 Characters LCD display 2 numbers of loop card and 200 devices in any combination per loop. Day / Night Mode facility. USB 2.0 Interface for PC connectivity. Rs. 485.00 Communication facility for Network / Repeater / MODBUS / BACnet. Programmable Auto Silence Facility. Programmable AC Loos Delay. Programmable Silence Inhibit. Two No’s of programmable inputs. Battery low audio, visual warning. Three programmable Form C relay for Fire, Fault and Supervisory. Primary Power 120 / 220VAC + 10% -15%, 60 / 50 Hz. Standby Power 24V D.C (2 No’s of 12V, 40 Ah (Max), Built in for 12Ah) Sealed Lead acid battery Operating Condition Operating Temperature0 - 49° C / 32-120° F. Relative Humidity93 ± 2% RH (non-condensing) at 32 ±2° C / 90 ±3° F including taking down old unserviceable Panel complete all as specified and as directed.
77Supply, commissioning and testing of Smoke detector Operating Voltage Range: 9 to 32 VDC Volts Non-polarized Standby Current: =100µA @ 24 VDC, Maximum Alarm Current (LED on ): =55mA @ 24 VDC, Operating Humidity Range: 10% to 93% Relative Humidity, Non-condensing, Operating Temperature Range: 14°F to 120°F (-10°C to 49°C), Adjustable Sensitivity: 1-2.5%/FT, Height: 2.2 (55 mm) installed in Base including taking down old unserviceable smoke detector complete all as specified and as directed. Make: Ravel Electronics Pvt Ltd or equivalent make as approved by GE.
78S&F in repair of Batteries DC, 12V, 7 AH, lead acid duly initial charged complete all as specified and as directed. Make: Exide / Star Gold
79Supply, commissioning and testing of Fire Alarm Hooter made out of iron, red colouroperatingvoltage 24 DC supplyDimensions (L x B x H): 18.5cm x 13 cm x 7.5 cm including taking down existing fire alarm hooter complete all as specified and directed. Make: Ravel Electronics Pvt Ltd or equivalent make as approved by GE.
80Supply, commissioning and testing of Addressable manual call point resettable type including taking down existing addressable manual call point complete all as specified and as directed. Make: Ravel Electronics Pvt Ltd or equivalent make as approved by GE.
81S&F in repair of Hydrant valve single headed Gun metal landing valve (internal/external Fire-Hydrants) with oblique type single outlet complete with hose coupling adaptor of 63 mm size, instantaneous spring lock arrangement and blank cap with chain conforming to IS 5290 complete all as directed
82S&F in repair of Flanged stand post CI of 80 mm dia 1.5 m height complete all as directed
83M&L for Maintenance of Automatic Transfer Switch of rating up to 630 Amp of Make Havells/ Legrand/ L&T at Valsura complete by taking the shut down with prior intimation and disconnecting incoming and outgoing connections, refixing the same after complete maintenance, replacement of fuses, tripping mechanism, tripping coils, pole assembly, control unit, auxillary switch, incoming and outgoing connections and replacement of overheated/ faulty portion of control circuit wiring as per above mentioned make as and when as directed by Engineer-in-Charge Note: (i) Spares required for repairing/ servicing of ATS will be measured and paid separately under relvant item of this Schedule "A" (BoQ). (ii) Fixing rate of the spares including testing is deemed to be inclusive in quoted rate of this item.
84Supply only Closing Coil for ATS upto 630 Amp, 4 pole as per existing make.
85Supply only Control unit for ATS upto 630 Amp, 4 pole, as per existing make.
86Supply only Trip coil of assy for ATS of rating upto 630 Amp as per existing make.
87Supply only Auxiliary switch for ATS of rating upto 630 Amp as per existing make.
88Supply only Pole assembly for ATS of rating upto 200 Amp as per existing make.
89Supply only Pole assembly for ATS of rating 315 Amp as per existing make.
90Supply only Pole assembly for ATS of rating 400 Amp as per existing make.
91Supply only Pole assembly for ATS of rating 630 Amp as per existing make.
92M&L for servicing and repair to HT oil switch of size upto 630 Amp complete by taking the shut down with prior intimation and opening the Oil chamber of HT switch gear and cleaning the contacts, put the fuse in position and testing complete all as specified and as directed by Engineer-in-Charge.
93S&F in repairs HT HRC type fuse, rating 40/63 Amp of HT Oil Switch complete by taking the shut down with prior intimation and opening the Oil chamber of HT switch gear and cleaning the contacts put the fuse in position and testing complete all as specified and as directed by Engineer-in-Charge. Make: L&T/ Bussmann/ CG Lucy
94M&L for servicing of LT ACB of rating up to 630 Amp, 415 Volt, 50 Hz of any make at Valsura complete by taking the shut down with prior intimation and cleaning the ACB by using air blower, tightening of connection of control circuit and complete checking of all fuses and control circuit for smooth functioning by employing one skilled tradesman as and when required including consisting of followings:- (a) Checking the control circuit wiring and rectifying the same with new rewiring with proper size and color code if found required at site. (b) Checking the components for replacement such as Shunt release, UV release,ammeter, voltmeter etc. c) Resetting and testing.of relay setting for proper functioning.
95S&F in repair copper bus bar of rating as per required at site, with supporting insulator duly fitted in PVC insulated sleeve in existing panel with requisite in shape and size required at site for fixing the bus bar at existing panel complete all as specified and directed by Engineer-in-Charge.
96S&F in repair 1100 Volt flexible single core cables with tinned copper stranded conductor PVC insulated and sheathed including copper lugs at both sides of the ends and all accessories required as per the site requirement for cross-sectional area 240 Sqmm including testing on competion complete all as specified and as directed.
97All as per serial item No. 96 here-in-above, but cross-sectional area 185 Sqmm.
98All as per serial item No. 96 here-in-above, but cross-sectional area 16 Sqmm.
99All as per serial item No. 96, here-in-above, but cross-sectional area 10 Sqmm.
100All as per serial item No. 96 here-in-above, but cross-sectional area 2.5 Sqmm.
101M&L for CT"s of required ratio from 200/5 to 800/5 in replacement in existing feeder pillar box and connect terminals to APFC panel and testing on completion complete all as specified & as directed by Engineer-in-Charge.
102S&F in repair Capacitor duty contactors, 3 pole, 230/415 V, 50 Hz of type MO C5 with auxiliary contacts for upto 5 kVAR rating complete all as specified & as directed.
103S&F in repair Capacitor duty contactors, 3 pole, 230/415 V, 50 Hz of type MO C12.5 with auxiliary contacts for upto 12.5 kVAR rating complete all as specified & as directed.
104S&F in repair Capacitor duty contactors, 3 pole, 230/415 V, 50 Hz of type MO C15 with auxiliary contacts for upto 15 kVAR rating complete all as specified & as directed.
105S&F in repair Capacitor duty contactors, 3 pole, 230/415 V, 50 Hz of type MO C25 with auxiliary contacts for upto 25 kVAR rating complete all as specified & as directed.
106S&F in repair 6-stage APFC relay with built in P.F Meter complete all as directed.
107S&F in repair 8-stage APFC relay with built in P.F Meter complete all as directed.
108S&F in repair 3-position selector switch centre off for auto Manual operation complete all as directed.
109S&F in repairs MCB SP 6 to 32 Amp, 240 V, 50 Hz, AC supply, 10 kA, "C" Curve, complete all as directed.
110S&F in repairs MCB TPN 20 to 32 Amp, 415 V, 50 Hz, AC supply, 10 kA, "C" Curve, with proper size lugs complete all as directed.
111S&F in repairs MCB TPN 40 to 63 Amp, 415 V, 50 Hz, AC supply, 10kA, "C" Curve, complete all as directed.
112S&F in repair Power factor improvement Capacitor banks, Cylindrical type, 3 phase, 440 V,Heavy duty of as per required at site from 5 to 25 kVAR LTCCR super heavy duty type capacitor complete all as directed. Make: L&T or equivalent in EPCOS/ C&S
113S&F in repair R/Y/B phase Indicator lamps LED type complete all as directed.
114S&F in repair power contactor ML 3 including necessary connections for incoming and outgoing connections complete all as directed. Make: L&T Cat No. SS90721 or equivalent in makes mentioned in Appendix "B" here-in-after.
115Disconnecting/ Taking out the existing Servo stabilizers transformer from site for repairing and transporting to workshop for servicing and repairing, including loading, unloading and handling to carry out repairs and refixing the same after repairing, installation, testing and commissioning at its original/ newlocation as ordered, decanting the transformer oil and checking of all parts for repair/ replacement of parts of 100 to 300 kVA capacity of servo controlled stabilizers 440 V, 3 Phase, AC 50 Hz, complete all as directed by Engineer-in-Charge.
116Disconnecting/ Taking out the existing Servo stabilizers transformer from site for repairing and transporting to workshop for servicing and repairing including loading, unloading and handling to carry out repairs and refixing the same after repairing, installation, testing and commissioning at its original/ newlocation as ordered, decanting the transformer oil and checking of all parts for repair/ replacement of parts of cap from 15 to 30 kVA capacity of servo controlled stabilizers 440 V, 3 Phase, AC 50 Hz complete all as directed by Engineer-in-Charge. Notes for serial item No. 115 & 116: (i) Spares required for replacement is measured and paid separately under serial item No. 117 to 125 of this Schedule "A" (BOQ) (ii) Fixing rate of the spares including testing is deemed to be inclusive in quoted rate of this item.
117Supply only Control push buttons/ switches/ fuse carriers/ knobs etc
118Rewinding of coils all as per its original specifications by copper conductor and with necessary insulation materials.
119Supply only LT bushing with brass terminal, neoprene rubber gasket and washers etc complete.
120Supply only Transformer oil up to standard level marking with new oil as per IS 335 having dielectric strength not less than 40 KV at 2.5 mm gap.
121Supply only Servo control motor as per existing model for controlling the voltage.
122Supply only Cork/ Neoprene rubber Gasket set complete.
123Supply only PCB for Servo controlled voltage stabilizers as per existing model and make or equivalent model and make as approved.
124Painting of Stabilizer body complete with two coat of Siemens gray paint with spray paint complete all as directed.
125Filtration of transformer oil of the transformer at site by providing filtration machine at site.
126M&L for Earthing with & including galvanised mild steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than2.25 m below normal ground level) with top edge of the earth plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to & including galvanized mild steel strip 32x6 mm as earth lead, including nuts, bolts, check nuts & washers of galvanized iron or steel and riveted/welded to earth plate at one end and other end of strip connected to Panel / transformer / GOD / equipment body / test point with two Nos nuts bolts or welding with steel structure, GI earth strip encased in and including 40mm bore GI light grade pipe with all fittings from upper edges of earth plate upto 7.5 metre above ground level fixed with and including 25x3mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from earth pit to top of electrode and including funnel, wire mesh, copper lugs etc complete with earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40mm thick RCC (1:2:4 type B1) cover complete all as specified and shown in electrical plate No 3 of SSR Part-I including necessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exc 50m complete all as specified and as directed including dismantling & taking out old existing unserviceable earthing. Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner.
127S&F in repair MCCB thermal magnetic protection unit rating 630 Amp, 4 pole, 36 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and including necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items andtaking down old item complete all as specified & as directed. Make:Legrand Cat Part No. 4220 09 or equivalent in makes mentioned in Appendix "B" here-in-after.
128S&F in repair MCCB thermal magnetic protection unit rating 400 Amp, 4 pole, 36 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and including necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items andtaking down old item complete all as specified & as directed. Make:Legrand Cat Part No. 4220 07 or equivalent in makes mentioned in Appendix "B" here-in-after.
129S&F in repair MCCB thermal magnetic protection unit rating 160 Amp, 4 pole, 36 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and including necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items andtaking down old item complete all as specified & as directed. Make:Legrand Cat Part No. 4200 97 or equivalent in makes mentioned in Appendix "B" here-in-after.
130S&F in repair MCCB thermal magnetic protection unit rating 250 Amp, 4 pole, 36 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and including necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items and taking down old item complete all as specified & as directed. Make:Legrand Cat Part No. 4202 49 or equivalent in makes mentioned in Appendix "B" here-in-after. Note for Sl item No. 45 to 48: Rate quoted deemed to included for taking down the existing MCCB from panel board and incoming / outgoing cable and fix the new MCCB / incoming / outgoing cable connections of any size/ rating in position at panel board.
131S&F in repair ATS 630 Amp, 4 pole, AC-31A, 50 Hz, 415 V, with controller, Automatic / manual with complete protection complete all as specified and as directed. Make: Havells IHYFCDO630 or equivalent in makes mentioned in Appendix "B" here-in-after.
132S&F in repair ATS 400 Amp, 4 pole, AC-31A, 50 Hz, 415 V, with controller, Automatic / manual with complete protection complete all as specified and as directed. Make: Havells IHYFCDO400 or equivalent in makes mentioned in Appendix "B" here-in-after.
133S&F in repair ATS 200 Amp, 4 pole, AC-31A, 50 Hz, 415 V, with controller, Automatic / manual with complete protection complete all as specified and as directed. Make: Havells IHYFCDO200 or equivalent in makes mentioned in Appendix "B" here-in-after.
134S&F in repair Multifunction meter of 96x96 mm size, flush mounting, complete with digital display, LED showing Voltage, current, PF, Frequency, electrical parameters complete all as specified and as directed. Make: L&T Cat No. WL411010OOOO or equivalent in makes mentioned in Appendix "B" here-in-after.
135S&F in repairs 42Ah 12Volt Lead acid battery (Maintenance free battery with min 2 years warranty) for 10/ 15 kVA UPS including necessary connections complete. Make: Exide Powersafe plus or equivalent in makes mentioned in Appendix "B" here-in-after.
136S&F in repairs charging card for 15 kVA DSP based 3P-1Ph UPS. Make: APLAB or equivalent as approved by GE.
137S&F in repairs DC driver card for 15 kVA DSP based 3P-1Ph UPS. Make: APLAB or equivalent as approved by GE.
138S&F in repairs display card for 15 kVA DSP based 3P-1Ph UPS. Make: APLAB or equivalent as approved by GE.
139S&F in repairs bypass card for 10 kVA DSP based 3P-1Ph UPS. Make: APLAB or equivalent as approved by GE.
140S&F in repairs Transformer card for 10 kVA DSP based 3P-1Ph UPS. Make: APLAB or equivalent as approved by GE.
141S&F in repair ACB 630 Amp, 4 pole, 50kA single frame drawout, mannual and Electrical Versions, including advanced self powered electronic protection units (Legrand Cat No. 0281 67) and shunt coil, close coil working on 220-250 V AC, Neutral Overload protecton OFF-50%-100% inbuilt temperature protection, Real terminals- vertical or horizontal connection with bars (Legrand Cat No. 0288 97), fast operation type DMX SP 2500 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and ncluding necessary addition/ alteration to existing panel with welding cutting to steel structure and providing new steel items and taking down old item complete all as specified and as directed. Make: Legrand Cat No 6695 42 or equivalent in makes mentioned in Appendix "B" here-in-after.
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail