Tender For Proposed Construction Of Auditorium Hall (500 Seats) For Kasturba Gandhi Balika Vidalaya At Chandankiyari., Bokaro-Jharkhand

TDR : 38389317

Tender Notice
BOQ

Expired

Bokaro , Jharkhand

Tender Brief : Tender For Proposed Construction Of Auditorium Hall (500 Seats) For Kasturba Gandhi Balika Vidalaya At Chandankiyari.

Document Fees
₹ 10000 /-

EMD
₹ 405000.0 /-

Tender Value
Refer document

Submission Date
10-07-2023

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	EARTH WORK INEXCAVATION IN FOUNDATION Trenches in ordinary soil (vide classification of soil item -A) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I.
2	Extra for earthwork in hard soil as per specification and direction of E/I (Vide classification of Soil item B)
3	FILLING IN FOUNDATION TRENCHES AND PLINTH in layers not exceeding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)
4	Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)
5	Providing designation 75-A, BRICK FLAT SOLING joints filled with local sand including cost of watering,taxes and royalty all complete as per building specification and direction of Engineer Incharge
6	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
7	1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stoneaggregate 20 mm nominal size)
8	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level :
9	1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)
10	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stoneaggregate 20 mm nominal size)
11	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
12	Providing, hosting and fixing above plinth level up to floor level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand ), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , exculuding the cost of reinforcement, with 1:1.5:3 (1cement : 1.5 coarse sand(zone-iii) : 3 graded stone aggregate 20mm nominal size)
13	Centering and shuttering including struting, propping etc. and removal of form for -
14	Foundation, footings, bases of columns etc.
15	Columns
16	ROOF SLAB
17	Beams, plinth beams,-
18	STAIRS -
19	CHAJJA
20	Providingtor steel reinforcement TMT FE 500 of following dia. rods as per approved design and drawing includingcarriage of bars to work site, cutting, bendingandbinding with annealedwirewithcostofwire, removal ofrustplacingtherods in position all complete as perbuilding specification and direction and direction of E/I.(ONLY VALID FOR SAIL & TATA STEEL, JSPL, ELECTRO STEEL LTD. AND VIZAG STEEL)
21	TOR 8 MMDIA. @ 30% of total steel qty.
22	TOR 10 MMDIA. @ 15% of total steel qty.
23	TOR 12 -32 MM DIA. @ 55% of total steel qty.
24	Providing designation 75A brick work in C.M. (1:6) in foundation & plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints,cost of screening materials raking out joints to 15mm depth , curing, taxes & royalty all complete as per building specification & direction of E/I.
25	Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 20mm nominal size)
26	Extra for providing and mixing waterproofing material in cement conncrete work in doses by weight of cement as per manufacturer\"s specification.
27	Providing designation 75 B BRICK WORK in CM. (1:6) in SUPERSTRUCTURE with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening,racking out joints to 15 mm depth,curing, taxes and royalty all complete as per building specification and direction of Engineer Incharge
28	Providing125 mm thick REINFORCED DESIGNATION75 A BRICK WORK in C.M. (1:4) in SUPERSTRUCTURE with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15 mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of Engineer Incharge .
29	Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.
30	Providing 12 mm Thk. cement plaster(1:6) on inside walls with clean course sand of FM-1.5including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all completeas per building specification and direction of E/I
31	Providing 6mm cement plaster(1:4) in ceiling with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all completeas per building specification and direction of E/I
32	Providing 12 mm cement plaster (1:3) with clean course sand of FM-1.5including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all completeas per building specification and direction of E/I
33	Providing 1.5 mm th. cement punning includingcuring, carriage of water with all leads and lifts as per building specification and direction of E/I.
34	Providing 19 mm thick water proof CEMENT PLASTER(1:3) on outside wall with clean coarse sand of F.M.1.5 wth 5% cico or any other waterproofing compound including cost of screening, curing making grooves with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I.
35	Providing & fixing FAN HOOK of 16 mm dia M.S. bar, 1 M long bent to required size and shape, placed in position and fluid in the R.C.C. slab-beam at the time of casting all complete as per building specification and direction of E/I.
36	Supplying, fitting & fixing 250 x 20 x 6 mm L-type M.S. clamp properly fishtailed including making holes and setting the same in 375 x 125 x 75 mm cement concrete block (1:2:4) with cost of all layout and materials and taxes as per building specification and direction of E/I.
37	Making20x6 mmgroovesinplaster surface over walls trully horizontal orvertical asspecifiedat regular intervals atallheightsincluding cleaningfinishing , scaffoldingand curingwith all leads andlifts of water all complete as per buildinngspecification and directionofE/I.
38	Providing and laying DOUBLE CHARGE VITRIFIED FLOOR TILESin different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and confirming to IS : 15622/ ISO 13006, of approved make, in all coloursand shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.30 kg per sqmincluding grouting the joints with white cement and matching pigments etc. complete. SIZE OF TILE- 600MMX600MM
39	Marble stone flooring with 18 mm th marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with:
40	Udaipur Green Marble
41	Extra for pre finished nosing to treads of steps of marble stone
42	Extra for marble stone flooring in treads of steps and risers using single length upto 2.00 m
43	Providing & laying 15 mm to 23 mm thick KOTAH STONE SLAB FLOORING and skirting of approved size, texture and colour over 19 mm thick base of line mortar (1:1:1) Lime putty: Surkhi: Coarse sand) laid over and jointed with grey cement slurry mixed with pigment ot match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.
44	Providingand laying 25 mm thick kotah stone tiles in risers of steps, skirting and pillars of approvedsizetexture and colour laid over 12 mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing to granolithic finish with approved quality ofcarborandumstone including cost of curing taxes and royalty all complete as per building specification and direction ofE/I.
45	Extra for pre finished nosing to treads of steps of Kota stone/ sand stone slab
46	Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).
47	Ordinary cement without any pigment
48	Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and1.8 cm thick fixed in Urinal Partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement :2 coarse sand : 4 stone chips)as per direction of E/I and finished smooth.
49	Granite Stone of approved shade
50	suppling , fitting and fixing good quality well dressed and well seasoned sal wood work in chaukhat in doors window,sky light, fanlight and celevitial window opening including wedge over clmps all including application of two coats of wood preservative of approved quality on the surface , building walls and lintel all complete as per building specification and direction of El.
51	Supplying, fitting & fixing 35 mm th. Solid core type non-decorative double leaf FLUSH DOOR SHUTTERS in doors with block board core blended with high quality phenol formal dehydes synthetic resinboth side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts , handle,cleats aldrop, door stopper & sand blocks & taxes all complete as per detail drawing building specification & direction of the E/I.
52	Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately).
53	12mm thick commercial ply conforming to IS : 1328 BWR type
54	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
55	1.0 mm thick
56	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i. e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
57	For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
58	Powder coated aluminium (minimum thickness of powder coating 50 micron)
59	Providing and fixing glazing in aluminium window, ventilator shuttersetc. with EPDM / Neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):
60	With float glass panes of 4.0 mm thickness (weight notless than 10kg/sqm)
61	Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.
62	With 12 mm mild steel U beading
63	Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
64	Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge. (Approved brand - Godrej/ Dorset)
65	Providing and fixing aluminium round shape handle of outer dia.100 mm with SS screws etc. coplete as per direction of E/I.
66	Powder coated minimum thickness 50 micron aluminium.
67	Providing and fixing aluminium hanging floor door stoppers ISI marked anodized (anodic coating not less than grade Ac 10 as per I.S. 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.Twin rubber stopper
68	Providing and fixingaluminiumTOWER BOLTS ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required color or shade with necessary screws etc. complete.
69	300X 10MM
70	150X 10MM
71	Extra for providing lipping with 2nd class teak wood battens 25mm minimum depth on all edges of shutters (over all area of door shutter to be measured).
72	Providing and fixing bright finished brass 100 mm mortise latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.
73	Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
74	Supplying, fitting & fixing M.S. GRILL made of 20 x 6 mm flat as per approved design and drawing properly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.
75	Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :
76	3 mm thick
77	Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.
78	Covering of treated surface with PCC :- Providing 50mm thick Cement concrete M20 (1:1.5:3) maintaining slope in alternate 2mtX2mt panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering, and mixing cement concrete in mixer with admixture of integral waterproofing and placing in position striking curing, taxes and royality all complete as per building specification and direction of E/i. Panels that has been left should be casted next day. There should be 6mm gap betwwen panels. Brand - Sika Plastocrete Plus, MYK proof WP, Fosroc-Conplast X4211 C,. Dr. Fixit Pidiproof LW+.
79	Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying
80	a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.
81	(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.
82	The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
83	(WORKS TO BE DONE BY REGISTERED APPLICATOR OF PIDILITE/ SIKA/ ROFF WITH 10 YRS. GUARANTEE.)
84	Providing applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth copmlete .
85	Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I
86	Finishing walls with Premium Acrylic Smooth exterior paint with silicone additives \"Snowcryl - XT\" of M/S Snowcem India Ltd, or equivalent of required shade.
87	New work (Two or more coats applied @1.43 ltr / 10sqm. Over and including base coat of water proofing cement paint Snowcem Plus or equivalent applied @ 2.20 kg./10 sq.m. )
88	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall suface to prepare the surface even amd smooth complete.
89	Finishing walls with textured exterior paint of required shade :
90	New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm
91	Providing two coats of SYNTHETIC ENAMEL PAINT of approved shade and make over new WOODEN surface including cleaning the surface after removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification dirction of E/I.
92	Providing Primer one coat of read lead paint of approved make over new STEEL SURFACE preparing the surface after cleaning, removing rust, dirt, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I.
93	Providing 2 coats of SYNTHETIC ENAMEL PAINT of approved shade and make over STEEL SURFACE grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I.
94	Providing and fixing stainless steel(Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners, etc.)
95	Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of0.33 mmthick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm)50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’.
96	The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thicksheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.
97	With 16 mm thick beveled tegular mineral fibre falseceiling tile (NRC 0.55 to 0.6, (Approved Brand - Armstrong)
98	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recomme-nded jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
99	12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)
100	Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 48kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.
101	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
102	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (Approved Brand - Tata Bluescope/ Equivalent)
103	Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
104	Ridges plain (500 - 600mm)
105	Flashings/ Aprons.( Upto 600 mm)
106	Gutter (600 mm over all girth)
107	Providing & fixing on wall face unplasticised -Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia
108	110mm diameter
109	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
110	110 MM
111	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
112	Providing 250 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 250 mm apron including cost of earthwork involved with 75mm cement concrete (1:4:8) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I.
113	Making Soak Pit 2.5 m diameter 3.0 meter deep with 45x45cm dry briick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standerd design .
114	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
115	Supplying chemical emulsion in sealed containers including delivery as specified.
116	Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
117	Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :
118	Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete:
119	With chlorpyriphos/Lindone E.C. 20% with 1% concentration
120	Providing tuck pointing [1:3] in cement on brick work clean coarse sand of F.M 1.5 FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all completeas per building specification and direction of E/I
121	DT: Basic rates for 125/115 mm dia Drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH ring Machine all complete including supplying all meterial, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of engineer-in-charge. (Basic rates)
122	(i) Drilling up to 30 mtr. Depth below G.L. in Rural Area
123	Supplying, assembling, lowering and fixing in vertical position in borewell unplasticized PVC medium well screen (RMS) pipes with ribs, confirming to IS: 12818, including hire and labour charges, fittings and accessories etc. all complete, for all depths, as per direction of engineer-in-charge.
124	100 mm nominal size dia. -
125	Supplying,filling, spreading and levelling stone boulders of of size range 5cm to 20 cm, in recharge pit, in the required thickness, for all leads and lifts, all complete as per direction of Engineer-in-charge.
126	Supplying,filling, spreading and levelling gravels of size range, 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders,in the required thickness, for all leads and lifts, all complete as per direction of E/I.
127	Constructing brick masonary chamber for Underground C. I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455X610 mm internal dimensions, total weight of cover with frame to be not less than 38 KG. (weight of cover 23 kg. and weight of frame 15 kg) RCC top slab with 1:1.5:3 mix (1 cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand :10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:
128	Inside dimensions 455X610mm and 45 mm deep for single pipe line with common burnt clay F.P.S. (non modular) bricks of class designation 7.5
129	Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete.
130	150 MM dia R.C.C. pipe
131	250 MM dia R.C.C. pipe
132	Supplying fitting and fixing Galvanised wire mesh of average width of aperture 1.4 mm and nominaldia of wire 0.63 mm(2\"-0\"x2\"-0\"*2) in position as per specification and direction of E/I.
133	200/150 mm dia Deep borewell : Cost of drilling 200 mm X 165 mm X 125m deep brewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH Rig machine, all complete including supplying all all materials, tools drilling rig, Air compressure and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicle up to the site.
134	From 0.00 M to 50.00 M below G.L
135	From 51.00 M to 125.00 M below G.L
136	From 125.00 M to 200.00 M
137	Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.
138	200mm Nominal size dia.
139	Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
140	Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm Dia.
141	Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nutsof required size complete.
142	Supplying 100mm dia. Submersible pump sets confirming to IS 8034 and motor cvonfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ant polypropylene/ norylimpeller. Motor suitable for working on 415 V+10%, 3PH, 50 HZ, AC supply with cable guard, thurst carbon/ fibre bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined no return valve shall be provided with pump. 3 m submersible copper conductor cable in single/ double run and nylon rope as required length shall be provided with each pump.
143	Submersible pump set 100mm dia (with polypropylene/ Noryl Impeller) 2HP
144	Supplying and fitting of standared make DOL starter for submerssible pump with SS enclosure with 380/415 vols as per ISI. 5 HP
145	Supplying and fixing copper conductor PVC insulated and PVC sheathed.3 Core 2.5 Sqmm
146	Supplying and laying /lowering of GI pipe of 50 mm dia including of required fittings solvent etc complete job as per direction of E/I
147	Carriage of materials by mechnical mean including loading at source ,unloading at works site and stacking properly ,labour, POL, etc all complete as per direction of E/I.
148	LOCAL SAND, LEAD - 9 KM. + (1 KM KACHA)
149	COARSESAND , LEAD - 21 KM. + (1 KM KACHA)
150	STONE CHIPS , LEAD - 22 KM.
151	BRICKS , LEAD-= 7 KM.+ (1KM KACHCHA)
152	Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast iron P or S trap, 10 litre low level white P.V.C. Flushing cistern with munally controlled device (handle lever) conforming to IS:7231 Parryware/ Hindware with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.
153	White Vitreous China Orissa pattern W C pan of size 580 X 440 mm with integral type foot rest.
154	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
155	15mm nominal bore
156	Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.
157	15mm nominal bore
158	Providing and fixing C.P Soap Dish of aaproved size, shape and approved brand with concealed fittings, complete job.
159	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
160	15mm nominal bore
161	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
162	White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap
163	Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
164	Providing and fixing white vitreous china flat back half stall urinal of 580X380X350mm with white PVC automatic flushing cistern, parryware/Hindware with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass with waste fitting as per IS : 2566 P.V.C. trap with outlet grating and other couplings in C.P. brass including parenting of fitting and cutting and making good the walls and floors wherever required..
165	Single half stall urinals without 5 litre P.V.C. auotmatic flushing cistern
166	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end )
167	25MM nominal bore.
168	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
169	Providing and fixing 100mm dia. Steel Jali of approved quality.
170	Providing and fixing unplasticised P.V.C. connection pipe with c.p. nuts collar and bush of approved quality.
171	15 mm nominal bore with 45 cm length.
172	Providing And fixing 32 mm waste pipe for sink or wash basin including P.V.C. waste fittings complete.
173	Flexible Pipe
174	Providing & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised -Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion .
175	Coupler -
176	110 MM
177	Single pushfit Coupler
178	110 MM
179	Single tee with door
180	110X110X110 MM
181	Single tee without door
182	110X110X110 MM
183	Bend 87.5°
184	110 MM
185	SHOE
186	110 MM
187	Supplying and fixing 100mm S.C.I. trap with 100mm inlet and 100mm outlet, with all complete.
188	110X100 MM
189	Supplying and fixing 100mm S.C.I. trap with 100mm inlet and 75mm outlet, with all complete.
190	110X750 MM
191	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I.(Approved Brand - ASTRAL/ SUPREME)
192	Concealed work including cutting chases and making good the wall etc..
193	15 mm nominal dia Pipes
194	20 mm nominal dia Pipes
195	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement & testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL)
196	Exposed on Wall
197	25 mm nominal dia Pipes
198	Constructing brick masonary chamber for Underground C. I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455X610 mm internal dimensions, total weight of cover with frame to be not less than 38 KG. (weight of cover 23 kg. and weight of frame 15 kg) RCC top slab with 1:1.5:3 mix (1 cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand :10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:
199	Inside dimensions 455X610X mm and 45 mm deep for single pipe
200	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
201	Providing and fixing C.P. Towel Ring (round) with flange
202	Towel Ring -CAT. NO. - JAQUAR, AQN - 7721
203	Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sqmmPVC insulatedcopperconductor cablein surface / recessed PVC conduit with moduler type switch,moduler plate,suitable size GI box etc. as required .
204	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit,and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.
205	Wiringforlight/powerplugwith 2 x 4 sqmm. PVCinsulated, copperconductor single core cable insurface / recessed PVC conduitalongwith 1 no 4.0sq. mm FR PVC insulated copper conductor single core cable forloopearthing mm as required.
206	Wiring for circuit /submainwiringwiththe following size ofPVC insulated, copper conductor single core cable in surface / recessed PVC conduit as required:
207	2x1.5 sq.mm.+1x 2.5 sq mm.
208	2x2.5 sq.mm.+1x 2.5 sq mm(for switch board / 5A Switch Socket+AC IDU)
209	Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC/steel conduit including dismantlingas required.
210	2x1.5 sq mm
211	S/F of following sizes of PVC conduit alongwith the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required .
212	20 mm PVC coduit.
213	S/F modular type switch / socket:- Suppling and fixing following moduler switch / socket on the existing moduler plate & switch box including connection but excluding moduler plate etc. as reqd.
214	5/6 amps switch
215	15/16 amps switch
216	5/6 amps socket outlet
217	Suppling and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connection but exluding modular plateetc.as required..
218	Suppling and fixingmodulertype blanking plate on the existing modular plate & switch box excluding modular plate as required.
219	Supplying and fixing suitable size GI box with moduler platecover in the front on surface or in recess including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps. moduler type switch, connections painting etc. as required. (For light plugs to be used in non residential buildings).
220	Supplying and fixing suitable size GI box with moduler platecover in the front on surface or in recess including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps. moduler type switch, connections painting etc. as required. (For power plugs to be used in non residential buildings).
221	S/F ceiling rose:- Supplying and fixing 2 pin 5A of ceiling rose on the existing junction box / wooden blockincluding connection etc as required.
222	Supplying and fixing 6 amps. to 32 amps. rating, 240 volts10 KA `C\" curve,miniature circuit breaker suitable for inductive loadoffollowingpolesin the existingMCBDBcomplete with connections, testing andcommissioning etc. as required.
223	Single pole(6 to 32A)
224	40 amps.TPN
225	50/63 amps. TPN
226	Supplying and fixing offollowingway, horizontal typethree pole and neutral, sheet steel, MCB distribution board, 415 volts,on surface /recess,completewithtinnedcopper bushbar, neutral link,earthbar,din bar,detachable gland plate, interconnections, including painting, earthing etc. as required.
227	6 way (4+18)double door horizontal type
228	8 way(4+24)double door,horizontal type
229	80mm dia earthing electrode 2mtr Length/ 80mm dia earthing electrode 3mtr Length /50mm dia earthing electrode 2mtr Length/50mm dia earthing electrode 3mtr Lengthand backfill compound chemical 4 bag (per bag 25Kg)
230	Providing and fixing 6SWG GI wire at0.50 m below ground level for coductor earth electrode,including solderingetc as required.
231	Providing and fixing of lightning conductor finial, made of 25mm dia 300mm long GI tube, having single prong at top, with 85 mm fia6 mm thick base plate including holes etc complete as required.
232	Rivetting, sweating and soldering of copper/GI Tape (with another GI Tape, base of the finial or any other metallic object) as required.
233	Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall for lighting conductor as required (for horizontal run).
234	Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall for lighting conductor as required (for vertical run).
235	Providing and fixing testing joint, made of 20mm x 3mm thick GI strip, 125mm long, with 4 Nos of brass bolts, nuts, check nuts and spring washers etc complete as required.
236	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade.ofsizenot exceeding 35 sq mm. Direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.
237	Supply of ISI marked (IS : 7098 Pt-I) aluminium conductor XLPE Insulated armoured, served, sheathed cable 1100 volts grade. (Skytone, Rallison, CCI, Gloster make)
238	25 sq. mm.X 3.5Core
239	S.I.T.C of following rating recess/ surfface mounted LED round /square shape down light luminaiere with pressure die cast housing for single phase supply voltage luminarie shall be confirm to IS:10322 part-5/section 2 or IEC :62722 with all necessary accessories as required.
240	18/20w LED round down light.
241	2\"x2\" LED panel light
242	S.I.T.C of following size ceiling fan 3 blades confirming to IS-374:2019including wiring the down rods of standared length (upto 30 cm)with 1.5 sq mm FR PVC insulated copper wire suitable for 230v 50Hz single phase supply etc.as required.
243	1200mm (48\") BLDC star rating 32w Ceiling fan
244	1400mm (56\") BLDC star rating 32w Ceiling fan
245	Supplying of 9\" (230 MM )Metal exaust fan
246	Supplying of 15\" (380 MM )Metal exaust fan
247	S.I.T.C of following rating surfface mounted LED tube light fitting suitabe for 230v 50Hz single phase supply etc complete as required
248	20/22w LED tube light
249	S.I.T.C of following rating LEDstreet light luminaiere with pressure die cast housing and toughend glass cover (IP 66 protection )in existing pole/pipe for supply voltage 100-270 AC 50 Hz luminarie shall be confirm to IS:10322 part-5/section 3and shall be completewith all necessary accessories as required.
250	90/100W LED street light.
251	Providing of bulkhead fitting with 9/10w LED bulb.
252	Installation of exhaust fan upto 450 mm. sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required.
253	Erection of wall bracket / ceiling fittings of all sizes and shapes ontaining upto two GLS lamp per fitting complete with all accessories including connection etc as required.
254	Providing supplying and installing Armstrong \"Optra Acoustical Wall Panelling\" with square edge made of fibre glass subtrate 25mm thick and wrapped on the front side with an acoustically transparent and fire resistant fabric with an option of colours as per the choice of the Architect of size 2100x600 or 600x600mm providing a minimum sound absorption level of 0.90 NRC to be affixed to wall using wall panel impalers including fixing of panel to the wall surface byself taping screws. Silica based construction adhessive shall be dabbed on to the prjecting elements (spikes) of the impalers and panels shall be pierced through the spikes with maintaining the line and level of panelApproved Brand - Armstrong/ Anutone)
255	Add 18 % GST
256	Add 1% Labour Cess

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Jharkhand Tenders

Construction Tenders

Building Construction Tenders

Auditorium Construction Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Proposed Construction Of Auditorium Hall (500 Seats) For Kasturba Gandhi Balika Vidalaya At Chandankiyari., Bokaro-Jharkhand

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Proposed Construction Of Auditorium Hall (500 Seats) For Kasturba Gandhi Balika Vidalaya At Chandankiyari., Bokaro-Jharkhand

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us