Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees andsaplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 2 | Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunk and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Girth 30-60 cm |
| 3 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth anddisposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil : |
| 4 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.All kinds of soil : |
| 5 | Preparation of subgrade by excavating earth to an average of 22.5 cm depth, dressing to camber and consolidation with road roller of 8-12 tonne capacity including making good the undulation etc. and disposal of surplus earth upto 50 meters. |
| 6 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader onprepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions ofEngineer-in-Charge.With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25 With material conforming incl all carraiges. |
| 7 | Providing , laying ,spreading and compacting graded stone aggregate (size 53.00 mm to 0.075 mm ) to wet mix macadam specification including premixing the material with water at OMC inmechanical mix plant , carraige of mixed material by tipper at site , for all lead and lift , laying in uniform layers with mechanical pavers finishers in sub base /base course on well prepared surface and compacting with vibratory roller of 8-10 tonn capacity to achieve the desired density , complete as per specifications and directions of engineer i/c including all carraiges. |
| 8 | Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to siteby tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as perspecifications to achieve the desired compaction and density, complete as per specifications and directions of Engineer-in-Charge.50 to 100 mm average compacted thickness with bitumen ofgrade VG-30 @ 3.5% (percentage by weight of total mix) prepared inDrum Type Hot Mix Plant of 60-90 TPH capacity. including all carraiges. |
| 9 | Providing and applying tack coat using hot straight run bitumen of grade – VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning andpreparing the existing road surface as per specifications. On bitumen surface @ 0.50 Kg/sqm. |
| 10 | Providing and laying semi- dense Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. 25 mm compacted thickness with bitumen of grade VG- 30 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot MixPlant of 100-120 TPH capacity. including all carraiges. |
| 11 | Surface/berm dressing of ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish , lead upto 50mtr and lift upto 1.5 mtr |
| 12 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 |
| 13 | Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. allcomplete as per direction of Engineer-in-charge |
| 14 | Chequerred precast cement concrete tiles 22mm thick in footpath on 20 mm thick bed of cement mortar 1:4 dark shade using ordinary cement |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 16 | Footings |
| 17 | columns |
| 18 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 19 | Shelves (cast-in-situ)/slab |
| 20 | Weather shades, chajjas, corbels etc. including edges. |
| 21 | Lintels /beams |
| 22 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing with 1:3:6 mix |
| 23 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:2:4 mix |
| 24 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6 mix |
| 25 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 26 | Providing and laying in position cement concrete in 1:1.5:3 |
| 27 | Supplying and stacking at site good earth |
| 28 | Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing off by spreading andneatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/andmanure before and after flooding trench with water |
| 29 | Spreading of sludge, dump manure or/and good earth in requiredthickness as per directions of officer in-charge |
| 30 | Edging with bricks laid dry length wise including excavation,refilling, consolidating with hand packing and spreading neatly surplus earth within a lead of 50 m Common burnt clay (non modular) bricks of class designation 7.5. |
| 31 | Grassing with selection no. 1 grass including watering & maintenance of the lawn for 30 days or more till the grass forms a thick lawn free fromweeds & fit for mowing including supplying of good earth if needed (thegood earth shall be paid separately.) Qty =3 x250 x70=70000 sft or 6505 sqm |
| 32 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mixfoundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III): 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 33 | Providing and fixing square- mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design.100 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 34 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing inposition and binding all complete . |
| 35 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer all complete.(welded) |
| 36 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. as required in gratings frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 37 | Providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener andEPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required |
| 38 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 39 | Tile brick masonry with common burnt clay tile bricks of class designation 10 in including curing complete in cement sand mortar 1:6 . Qty = 1100 \" x 0.75\"x 0.25\" =206.25 cft 0r 5.84 cum |
| 40 | Providing and fixing tiled False Ceiling of specified materials of size 595x595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms/sqm both side inclusive ) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200 x 600mm and secondary cross “T” of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size24x24x0.30mm and laying false ceiling tiles of approved texture in the grid including, wherever, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T”runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center to center along size 85x30x0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard manufactured from natural gypsum as per IS 2095 part-I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 41 | Providing and fixing stainless steel (Grade 304) railing made of Hollowtubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steelbolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered) |
| 42 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size includingnecessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge |
| 43 | a)For Fixed portion Powder coated aluminum (minimum thickness of powdercoated 50 microns) |
| 44 | For shutters of doors, windows & ventilators includingproviding and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprenegasket required (Fittings shall be paid for separately.)Powder coated aluminum (minimum thickness of powder coated 50 microns) |
| 45 | Filling the gap in between aluminum frame and adjacentRCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5mm width |
| 46 | Providing and fixing Anodized aluminum grill (Anodized transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainlesssteel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved Anodized aluminum standard section around the opening, all complete as epr requirement and direction of Engineer-in-charge. (onlyweight of grill to be measured for payment) Qty vide item=334.80 sqm @ 3.25 kg/sqm =1088 kg |
| 47 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors asrequired and making good the same matching to the existing floorfinishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer plate etc. complete as per the direction of Engineer-in-charge.With Stainless Steel cover plate minimum 1.25 mm thickness |
| 48 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc.complete as per architectural drawings and directions of engineer-incharge.Pre-laminated particle board with decorative lamination on both sides. |
| 49 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin- charge.With floating glass panes of 5.0 mm thickness (weight not less than 10.00 kg / sqm) |
| 50 | Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16 mm |
| 51 | Providing and fixing aluminum Towerbolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete.300x10 m |
| 52 | Providing and fixing aluminum Towerbolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete.150 x 10mm |
| 53 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to requiredcolour and shade with necessary screws etc. complete. 125 mm |
| 54 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to requiredcolour and shade with necessary screws etc. complete.230mm |
| 55 | Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete |
| 56 | Providing and fixing ISI: 12817 marked Stainless Steel Butt Hinges with Stainless Steel screws etc. complete 100x58x1.90 mm |
| 57 | Providing and fixing ISI: 12817 marked Stainless Steel Butt Hinges with Stainless Steel screws etc. complete 75x47x1.80 mm |
| 58 | Providing and fixing aluminum casement stays, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed torequired colour or shade with necessary screws etc. complete : |
| 59 | Providing and fixing bright finished Aluminium 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per IS : 1868) aluminum lever handles of approved quality with necessary screws etc. complete. |
| 60 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required of jaguar /Essco/Cera or equivalent make |
| 61 | Providing and fixing white vitreous china flat back half stall urinal of size580x380x350mm with White P.V.C automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS:2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required: Single half stall urinal with 5 liter P.V.C automatic flushing cistern. |
| 62 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls whereverrequired:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 63 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 64 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040mm bowl depth 250mm |
| 65 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. |
| 66 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete Semi rigid pipe 32 mm dia |
| 67 | Providing and fixing 100 mm CP grating for gully trap. |
| 68 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved makeand shade with 6 mm thick hard board backing :rectangular 1500x 450 |
| 69 | Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete |
| 70 | Providing and fixing toilet paper holder C.P. brass |
| 71 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour,weighing not less than 105 gms. |
| 72 | Providing and fixing CP Waste Coupling for wash basin and sink, of approved quality and colour Waste coupling 31mm of 79 mm length and 62 mm breadthweighing not less than 45gms. |
| 73 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms. |
| 74 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour:450 mm long towel rail with total length of 495 mm, 78 mmwide and effective height of 88 mm, weighing not less than 170 gms. |
| 75 | Providing and fixing CP urinal cock of approved quality15 mm nominal bore, 80 mm long, 42mm high and 30 mmwide with BSP female threads weighing not less than 48 gms |
| 76 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved of make essco/jaguar/cera |
| 77 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 |
| 78 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 79 | Providing and fixing 15 mm nominal bore C.P. brass health faucet with 1.2 m Flexible Hose pipe of approved quality conforming to IS standard of Jaguar/Essco/Cera or equivalent. |
| 80 | Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. |
| 81 | Cutting holes up to 30x30 cm in walls including making good the same With common burnt clay (non modular) bricks |
| 82 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete |
| 83 | a)25mm |
| 84 | b)20mm |
| 85 | Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) |
| 86 | a)25mm |
| 87 | b)20mm |
| 88 | c)15mm |
| 89 | d)CP Brass Extension nipple 150x50 |
| 90 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete 25mm |
| 91 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete |
| 92 | a)25mm |
| 93 | b)20mm |
| 94 | Providing and laying non-pressure of specified class R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc.complete Non-pressure NP-3 class (Medium duty) R.C.C. pipes . 600 mm |
| 95 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand:10 graded stone aggregate 40 mm nominal size) including bed concrete for encassing of pipes .Qty = 700\" x 4\"x 1\"= 2800cft or 79.29 cum |
| 96 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. |
| 97 | a)150mm |
| 98 | b)110mm |
| 99 | c)75mm |
| 100 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. |
| 101 | a)150 mm plain bend |
| 102 | b)110mm plain bend |
| 103 | c)75mm plain bend |
| 104 | d)100x100x75 Tee |
| 105 | e)75x75x75 Tee |
| 106 | f)Collar 150mm |
| 107 | g)Collar 110 mm |
| 108 | h)Cowl |
| 109 | i)Door bend 110mm |
| 110 | j)Door bend 150mm |
| 111 | k)clamp m.s |
| 112 | Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In- Charge. Thejoints shall be of extruded aluminum base members with, self aligning and self centering arrangement support plates as per ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to itscomponents. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s preengineered self-centering arrangement that freely rotates/ moves in all directions. The self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint system shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint system to have water tight joint is mandatory requirement. Materialshall confirm to ASTM 6063. (200 mm gap) |
| 113 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank |
| 114 | 12 mm cement plaster in 1:6 (1cement:6 fine sand ) mix |
| 115 | 15 mm cement plaster on the rough side of single or half brick wall in 1:4 (1cement:4 fine sand ) mix |
| 116 | 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
| 117 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 infoundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 118 | Extra for brickwork with common bunt clay bricks in superstructure upto level V |
| 119 | Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 120 | Extra for half Brick masonry in superstructure above plinth level upto floor V level |
| 121 | Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and includingbase coat of exterior primer applied 2.20kg/10sqm |
| 122 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 123 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 2mm thick |
| 124 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand and manufacture. |
| 125 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels |
| 126 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge |
| 127 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigmentsetc. complete 1000x1000 mm |
| 128 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling /grouting and finishing complete as per direction of Engineer-in-charge. |
| 129 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. |
| 130 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointingin white cement mixed with pigment of matching shade complete. |
| 131 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishingthe top smooth and curing complete |
| 132 | Providing and fixing fly proof wire gauze to windows, clerestory windows and doorscomplete Stainless steel (grade 304) wire gauze of 0.5mm dia wire and 1.4mm aperture on both sides |
| 133 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) includingmaking joints with or without grooves (thickness of the joints except at sharp curve shall not to be more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-incharge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 134 | Carraige of materials by M.T |
| 135 | a)Brick avg lead 1 KM |
| 136 | b) Sand Avg lead by 44 km |
| 137 | c) Aggregate by 44 km lead |
| 138 | d)Good Earth 1 km |
| 139 | e) Disposal of mulba within 1 km leet |
| 140 | Providing and fixing water pump motor 2 HP incl all fittings complete job |
| 141 | Providing and supplyingof student desk made of 1\" square pipe frame with shelf seat made of 18 mm thick laminated board conforming to IS 12823/1990 with Pvc edge banding on all sides of make godrej /durian . |
| 142 | Providing and supplying of visitor chair (400x400x700) with arm chrome plated frame sturdy and comfortable padded with poly urethane foam of make godrej/durian. |
| 143 | Providing and supplying of Steel bookcase with four glass drawers(size 840x305x1675) of material M.S sheet conforming to commercial quality CR-1 , grade 340 of IS 513:2008 , sheet thickness 1.0 mm (minimum) shutter thickness 1.25 mm (minimum) glass thickness (5mm), finish shall be powder coated with bolting device controlled with lock.of make godrej/ durian |
| 144 | Providing and supplying of steel almirahs with shelves (910x480x1855)of material M.S sheet conforming to commercial quality CR-1 , grade 340 of IS 513:2008 , sheet thickness 1.0 mm (minimum) ,stiffened pedestal width 70mmfinish shall be powder coated with 3 way bolting device controlled with lock.of make godrej/ durian |
| 145 | Providing and supplying of steel filling cabinetswith drawers(760x430x1150)of material M.S sheet conforming to commercial quality CR-1 , grade 340 of IS 513:2008 , sheet thickness 1.0 mm (minimum) ,stiffened pedestal width 70mmfinish shall be powder coated with 3 way bolting device controlled with lock.of make godrej/ durian |
| 146 | Providing and supplying of steel almirahs locker with six compartment (915x485x1980)of material M.S sheet conforming to qualitygrade D of IS 513:2008 , sheet thickness 0.7 mm (minimum) ,stiffened pedestal width 70mmfinish shall be powder coated of make godrej/ durian. |
| 147 | Providing and supplying of Periodicals/Journals/Magazine Stand (760x 350x1230) with Aluminium powder coated of make godrej/durian. |
| 148 | Providing and supplying of Newspaper Stand (350x 310x 1230) with Metal powder coated of make godrej/durian. |
| 149 | Providing and supplying of drawing boards with stand as per A1 size sheet , engineeering board 23x 32\" natural wood 15 mm thickandsteel/aluminium standpowder coated with adjustable height |
| 150 | Providing and supplying of student sitting stools (400x400x600) of M.S powder coated frame wooden top . |
| 151 | providing and supplying of office tables of size 1200x600x750 with m.s powder coated frame and wooden top built in drawers with locking arrangement . |
| 152 | Providing and supplying of reading table for library (1350x700x 750 ) with M.s powder coated frame and wooden top. |
| 153 | Providing and supplying of lab tables (1350x 900x 750) with powder coated frame and S.S top . |
| 154 | Providing and supplying lecture stand 525x 375x1025 with Glass top sides ,engineering wood pre assembled with closed storage and microphone / audio fitted . |
| 155 | providing and supplying of conference table for 20 persons with ms powder coated frame and wooden top and microphone /audio fitted |
| 156 | providing and supplying office furniture executive table with 1 executive chair of make Godrej/durian . |
| 157 | Providing and supplying of 10 seater sofa arrangements with centre table and side tables .(Principal\"s room) of make godrej/durian |
| 158 | Providing and supplying 1 office table with 1 executive chair of ISI marked and as approved by engineer i/c of make godrej/durian. |
| 159 | Providing and supplying of white marker boards for lecture rooms 2440x1220 mm with white board with plyboard backing with provision to hang on walls . |
| 160 | Providing and supplying of Display boards for studio of size 2440x 1220 with soft board with plyboard backing with ms stands and provision to hang on walls. |
| 161 | Providing and supplying notice cum pin up boards of soft board with plyboard backing with provision to hang on walls. |
| 162 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &double action hydraulic floor spring type fixingarrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge . area = 10 x 1.5= 15 sft or 1.39 sqm |
| 163 | Providing and fixing aluminum tubular handle bar 32mm outer dia, 3.0mm thick & 2100mm long with SS screw etc. complete as perdirection of Engineer-in-charge. Anodized (AC 15)Polyester powder coated minimum thickness 50 micron aluminum tubular handle bar |
| 164 | providing and supplying reception counter made with 19mm ply and back made with 6mm ply and drawers fixed with channels and finished with PU polishsize 8\" x 2.5 \" =20 sft and top fitted with 12 mm toughened glass (that shall pe paid separately) |
| 165 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI boxetc. as required. |
| 166 | supply and fixing of 5 inch dia Fan Box / concealed box with round sheet cover for covering the base and bottom and dual painted with red oxide |
| 167 | Providing Installation testing and commissioning ofCeiling Fans of approved brands with connections etc as required Make:- Anchor/Indoasian/havells 0r equivalent |
| 168 | Supplying and fixing two module Stepped type electronic Fan Regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required |
| 169 | Supply,installation,testing and commissioning of Ceiling LED Panel type 10 watt day milky fitting with connections as required |
| 170 | Supply & installation, of Conceiled Box for LED Panelas required Make:Anchor/havells/CG |
| 171 | Supply & Installation of Exhaust Fans With Stylish Plastic Exhaust 250 mm(10\") in the existing opening including connections,testing commissioning etc as required |
| 172 | Supply and fixing Modular Blanking Plate on the existing modular plate and switch box excluding modular plateas required |
| 173 | a) 25 mm |
| 174 | b) 40mm |
| 175 | 1.0Sq. mm wire |
| 176 | 2 x 2.5 Sqmm + 1 x 2.5 sqmm |
| 177 | 2 x 4 Sqmm + 1 x 4 sqmm |
| 178 | 6 Module (200mmX75mm) |
| 179 | 6 pin 15/16 A socket outlet&15/16 A switch |
| 180 | 5 pin 5/6 A socket outlet & 5/6 A switch |
| 181 | Supplying and fixing following 5 pin 5/6 A modularswitch /socket on the existing modular plate & swichbox including connections etc. as reqd. |
| 182 | Providing and fixing of Decorative Mirror Light/ Wash Basin Lightand complete with 9 watt LED Bulb. Make:- Anchor/Indoasian/havells |
| 183 | Providing and fixing of full hd3400 lumens 1920x 1080 resolution Projector with screen(HDMI,VGA,Miracast enabled)with all accessories complete of make Epson/samsung or as directed by engineer i/c. Complete job |
| 184 | Drilling/boring of 125 mm dia bore hole well for construction of tube wells . The job shall be inclusive of all logistic support in terms of men , machinery and stores at site .the charges on account of loading /unloading , shifting of men and machinery shall be arranged by the firm .The bore has to be cased simultaneously vide drilling in case of ODEX drilling or cased at the completion of drilling in open drilling .The specification of the bore well shall be as under 1) Min dia of the bore well 150 mm 2)max depth of the bore 150 mtr 3)dia of MS pipe to be used 125 mm 4)Acceptable make jindal/prakash/surya class of pipe \"C\"5)sample collection of the strata to be collected for examination after every 10 feet 6)Drilling / boring method to be used, Air rotary (prefered) .providing , fitting and lowering of 125 mm dia (nominal)MS casing pipe . the pipe shall be plane and bevelled ended and shall be lowered at desired level BGL . the avg. length of pipe shall not exceed 3.00mt .the welding electrodes shall be as per IS provisions complete job. |
| 185 | supply , Installation , testing and commisioning of 5H.p submersible type pump motor asembly with motor control panel. |
| 186 | supply and installation of 32 mm dia G.I riser pipe classB with 32 mm socket (Quantity of the riser shall depend on the drilling depth and the static water level of the well) |
| 187 | supply installation of 10 sq mm submersible cable (qty of the cable depends upon the position of submersible motor installed below ground level). |
| 188 | Providing fitting of bush , nipple , ball valve , clamps for holding pump motor. |
| 189 | SITC of 11/0.43 KV , 3 Phase 400 KVA Distribution Transrormerwith Bimetallic Terminal Connectors Energy Lcvel-2 |
| 190 | SITC of Gapless surge arrestor 9 KV,10 KA, LA with polymer/ Porcelain housing,Stn Type |
| 191 | SITC of 11 KV G.O AB Switch, 3 Phase, 3 pole 400A |
| 192 | SITC of 11 KV D.O Fuse 3 Phase 400A |
| 193 | SITC of 70 mm²/50 mm²(2ckt).185mrn(2Ckt) 400 MMsq Cable 1.1 KV GradePVC Insulated stranded ConductorFRLS type |
| 194 | Supply , laying & Commissioning of 9 Mtr Long Pole ST |
| 195 | Supply & fitting of 11 KV Disc Insulators (Polymer/ Porcelain) Complete with fitting (45KN) |
| 196 | Supply & fitting of GI Channel/Angle/ Flat of Sizes including clamps |
| 197 | Supply & fitting of Galvanized Nuts And Bolts |
| 198 | Supply & Laying of Earthing of Substation-Excavation of earth pit of dia 650 mm & depth 3000 mm,installation of earthing pipe of 40 mm Normal bore & 4 mm wall thickness & lenth 2.5 mtrlong as per IS 1239, GIStrip for neutral earthing of size 75 mmx10mm & 50 mmx6mm forconnection of transformer body.Go set & lightening arrestor as per IS 2629/85, GI nuts & Chamber made of brickMasonary with RCC |
| 199 | Supply & fitting of 11KV Pin Insulators (polymer/poreclain) with pins (5KN) |
| 200 | SITC of LT Distribution Panel Box for400 KVA DTR with MCCB forIncomer & SFU\"s for Outgoing Circuts (Complete job) including |
| 201 | Supply & fitting of Galvanised stay set with 50x80 mm stay clamp, guy insulator (2 Nos) anchor plate (200x200x6mm), nut bolts,2 Nos turn- buckles, 1.8 m long ,16 mm diameter solid GS stay rod & 7/3,15 mm dia GI stranded wire complete |
| 202 | Supply & fitting of Wedge Connectors/PG Clamps |
| 203 | Supply & fitting ofDanger Plates with Clamps |
| 204 | Supply & fitting of GI Barbed wire for anti Climbing |
| 205 | Supply & Laying of Cement Bottoming 1:2:4 mix as per REC standards 50m/pole |
| 206 | Supply & painting of poles Red oxide |
| 207 | Supply & Painting of Poles Aliminium paint |
| 208 | SITC of Trivector Meter with CT |
| 209 | Supply & fittingof Sundry items like aluminium lugs, jumpers, binding tape. |
| 210 | Supply & fitting of Galvanised stay set with 50x80 mmstay clamp, gI\ turn- buckles, 1.8 m long ,16 mm diarl\"eter solid GS stay rod & 7/3,15 mm di.1GI stranded wire completeuy insulator (2 Nos) anchor plate (200x200x6mm), nut -bolts,2 |
| 211 | 11 KV LINE/ISOLATION POINT0N9 MTR LONGST POLES |
| 212 | Supply , laying & Commissioning of 9Mtr long STPole(ST-410, SP-33 ) |
| 213 | Supply & fitting of GI-V cross Armwith top bracket lncluding clamp |
| 214 | Supply & fitting ofGI Channel./ angle Iron including clamps |
| 215 | Supply , fitting & commissioning of 11 KV G.O AB Switch 3 Phase |
| 216 | SITC of 50 mm ACR Conductor |
| 217 | Supply & fitting of PG clamps |
| 218 | Supply & fitting of 11 KV Pin Insulators (Polymer/Porcelain) Complete with fitting (45KN) |
| 219 | Supply & fitting of 11 KV Disc Insulators(Polymer/ Porcelain) Complete with fitting (45KN) |
| 220 | Supply & fitting of Galvanized Nuts and Bolts |
| 221 | Supply & fitting of Danger plate |
| 222 | Supply & fitting of GI Barbed Wire for Anti Climbing |
| 223 | Supply & Layingof Earthing complete |
| 224 | Supply & painting of Red oxide |
| 225 | Supply & painting of Aluminium paint |
| 226 | Supply & laying of Cement Bottoming 1:2:4 mix |
| 227 | Supply & fitting of Galvanised stay set with 50x80 mmstay clamp, gI\ turn- buckles, 1.8 m long ,16 mm diarl\"eter solid GS stay rod & 7/3,15 mm di.1GI stranded wire completeuy insulator (2 Nos) anchor plate (200x200x6mm), nut -bolts,2 |
| 228 | INSTALLATION OF 11 KV HT METERING WITH CT & PT UNIT |
| 229 | SITC of 11Kv pilfer resistant metering cubicle for 3 phase 4 wire metering system made of MS sheel steel thickness not less than 2mm duly power coated painted suitable for indoor as well as outdoor as per the site requirement the cubicle shall painted through 7 compartments upper meter compartment and lower CT/PT compartment. provided with synthetic or semi synthetic gasket firmly glued to the surface. Dust, weather and vermin proof and shall comply degree of protection IP 65 both the chambers having one sided hinged door aggrementss. the metering panel shall be provided with two No MS channels of Size 100x50mm on the front and rear side duly welded and 4No of lifting hooks. It should be possible to take meter reading manually through CMRI and computer without opening the LV chamber door. |
| 230 | SITC of Single phase single core single ration Epoxy restin cast current Transformer suitable for 11Kv copper wound primary type with rated burden 5KV and accuracy class 0.5 or better and comforming to 152705 (Part 1&II) amended upto date ISF shall be upto 5 the CT ratio shall be as under 1. 2.5/5 for 25KVA DT 2. 5/5 for 63 KVA DT3. 7 5/5 for 100 KVA DT4. 15/5 for 200 KVA DT5. 20/5 for 250 KVA DT 6. 25/5 for 400 KVA DT7. 50/5 for 630 KVA DT8. 75/5 for IMVA DT |
| 231 | SITC of llkV/ 110 V. Three phase epoxy resin castPT with ratedburden 15VA perphase and accuracyclass0.5or betterandconformingto15:3156{part -1&11)amendedupto datewith proercolourcodedidentification PTs shallbeofuniforminsulatrngand withstand separate source 23kV pf for one minute. |
| 232 | SITC of Bus Bar detail , SITC of CTs bus bar:- 40x6mm copper strip or adequate size , SITC of PTs bus bar copper wire 8 SWG or 30x0.6mm copper flat strip to connect PT terminal or adequate size,Duly insulated by the monoplast tape |
| 233 | Supply & fixing of PVC copper wire flexible multi-strand of required size for secondary connections for CT wiring the minium wire size shall be 4mm (RYB) and for PT wiring minium wire size shall be 2.5 mm2 (RYB) |
| 234 | Supply & fitting of Copper lugs preferbaly ring type duly crimped for termination of wires and tapes |
| 235 | Supply & fixing of Grounding bus of minimum40mm copper25cm long fixed to the unit in HV Chamber The CTsPT meter and llkV Cable sheath shall be grounded to the bus through groundedwire (green) of min size 10mm2 |
| 236 | SITC OF 3 phase Wire HT CT/PT operated Fully static Smart Tri-Vector Energy meters DLMs Compliant CategoryC with RS232 port for modem compatibilt!y11KV/110V. Ph-Ph(3P,3W) meters for measurementof different electrical parameters includingActive Energy (KWh/ MWh). React v Energy lkVArh/MVArh), Apparent Energy (KVah/MVah) etc (make L&T Secure,ABB) |
| 237 | Providing & Fixing of Independent flexible PVC pipesfor CT wiring and PT wiring of appropate size from HT compartment to meter compartment |
| 238 | Supply & Fitting of Pedestal made out of MS Channel of size 75 x 40 min or angle ironof size 65 x 65x5mm. duly painted as per site requirement for mounting of metering panel including concrete foundation wherever required including costnuts and bolts |
| 239 | SITC of 3 core 11 KV aluminium cable XLPE armoured 35mm including cost of clamps for its fixing where ever required |
| 240 | SITC of Cable termination kits suitable for 3x 35mm XLPE cable (indoor/outdoor) |
| 241 | Providing & laying of Earthing 40mm GI pipe or 20mm Gi rod 2.5 mtr for metering unit earthing of metering cubicle through two no 25x5 mm flat iron |
| 242 | Providing and connecting of Jumpers at the tapping point after obtaining Proper shutdown for energising of11KVLine. |
| 243 | Job for carrying out inspection of 400 kva Sub-station including. HTline from concerned department complete job |
| 244 | Supply ,Installation,testing & Commissioning of 250KVA Servo Controlled Automatic Voltage Stabilizer With MCCB & Bye Pass Switch & with following specifications;a) Input voltage range = 208 Volts to 460Volts (Phase to Phase) ,b) Output voltage range = 415Volts + 1% (Phase to Phase),c) Frequency: 50 HZ.d) Capacity overload = 10% overload for four hour.e) Protection : Over Load & Short Circuitf) indoor typeg) Unbalance typeh) It shall Suitable for all power Factor.i) Cooling shall be ONAN. |
| 245 | Supply ,instalation,fabrication and commissioning of Low voltage Sub Main Panel on 415 volts 3 phase 50 htzs of 2mm thick CRCA / Sheet of powder size 4X6X1.5 rft . a)Providing and fixing od 600 amp TPN A1.Bus bar with required nos of thimbles etc (2 nos) b)315 amp 4 pole MCCB with breaking capacity C)250 kva 4 pole MCCBd)300 amp 4 pole change over switch(2 nos)e)63 amp SPN (6 nos)f)VSS meter/switchg) ASS meter/ switch |
| 246 | Supply & Installationfor Construction of Tin Shed& Concerete Plate form of required size forServo stabilizer , D G Set &Panels |
| 247 | Disposal of unwanted Mulba/ material from the site of work including Cheselling , repairing & making the same where ever required. |
| 248 | Earth work/ Trench Cutting 60 cm X 60 cm for laying of75 mm dia PVC Pipe including laying of 95 sqmmArmoured cableRE-fillingof trench & making the same. |
| 249 | SITC of 100 amp 4 pole change over switch |
| 250 | Supply and fixing of ST pole8Mtr.Long (410-SP-15) Complete with base plate 300 x 300 x 5mm and top cap with Pole depth of 1.5 meters including transportation charges. It also includes all the taxes as applicable along with charges incurred while testing and commisionnig the samefor LT Network |
| 251 | Providing ,installation,testing and Commissioning of 250 watt LED Street lightinstalled on each 8 mtr ST Pole with connection etc as required |
| 252 | Supply and fixing of 2x 2.5 sqmm multi strand wire make (Polycab, havells, or equivalent) for connection purpose from conductor to luminarie |
| 253 | Supply and fixing of 1sqmm wire for earthing purposes of lights installed |
| 254 | Supply and fixing of GI Brackets for supporting the lights installed on the top end of the ST Poles including clamps and variuos other accessories like nut and bolts . |
| 255 | Supply and fixing of 0.03 ASCR WEASEL conductor on 08 m ST poles |
| 256 | Supply and fixing of LT shackle insulators along with Shackle pins with Clamps on 8 meter ST Poles |
| 257 | Supply & painting of poles Red oxide |
| 258 | Supply & Painting of Poles Aliminium paint |
| 259 | Supply & Laying of Cement Bottoming 1:2:4 mix as per REC standards 50m/pole |
| 260 | Supplyinglaying & making outdoor connections including aluminium lugs and other jointing materials for 2 X 16 sqmm LT unarmoured Power Cable ,Almunium Conductor |
| 261 | Earthing ofSteel tubular, 8 Mtr. poles with 85 SWGGI wire (105 turns of 50mm dia spiral in 1.5 meters deep pit as per REC specifications |
| 262 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box etc. as required. |
| 263 | Supply and fixing ofGate Light / Globe including testing , commissioning & providing connections as required |
| 264 | Providing and fixing of18 watt LED Bulb |
| 265 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required |
| 266 | 2 x 2.5 Sqmm |
| 267 | 2 x 4 Sqmm |
| 268 | Providing & Fixing of maintanance free chemical earthing including digging/drilling of 2 mtr deep pit in hard/semi hard soil,chemical material and laying of pipe electrodes with external dia of 50mm & internal strip of 32x6 mm GI make with back fill compound 50 kg in the pit and disposal of unwanted material from earthing site to disposal site & earthing should provide desire able earth resistance value as per IS Standard |
| 269 | Construction of cement concerete inspection pit /main holes 1.5x1.5x9\" (LBH) above the earth installation with main hole cover of GI/Hard Plastic assembly & cavity to be filled withglass wool complete job |
| 270 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 271 | Disposal of unwanted Mulba/ material from the site of work& making good the same whereever required |
| 272 | Supplyinglaying & making outdoor connections & other jointing materials for 3.5X 240 sqmm LT Power Cable ,Almunium Conductor, ARMOURED |
| 273 | Providing and fixingAluminium Thimbles for making connections to 3.5 X 240/95/35sqmm Cable. |
| 274 | Providing & fixing of Semi Integrated Solar LEDStreet Light with following Technical Specification: 60 watt LED luminaire, 100 watt SolarPolycrystalline PV Module , 12.8V42 Ah LIFEPO4 Battery, 6 Meter GI Pole with accessoties Such as , Panel Stand/ T Stand, Light Arm , Nut Bolts ,DC Cable etc. Complete job Operatng Dusk to Dawn,Light mounting height 05 meter above the ground level and pole to be 01 meter below the ground,including cement bottoming 1.5 feet X 1.5 feet X 3 feetof ratio 1:2:4 and warranty of the Complete Solar system for 2 years from the date of commissioning. |
| 275 | SITC of AMF Panel suitable for 400 KVA DG Set as per companynorms |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
