Tender For Arm Of Logistic Group Buildings At Nsg Campus Manesar For The Year 2023 24 Sh Civil And Elect Maintenance, Manesar-Haryana

TDR : 38285024

Tender Notice
BOQ

Expired

Manesar , Haryana

Tender Brief : Tender For Arm Of Logistic Group Buildings At Nsg Campus Manesar For The Year 2023 24 Sh Civil And Elect Maintenance

Document Fees
Refer document

EMD
₹ 166815.0 /-

Tender Value
₹ 83.40 Lakhs /-

Submission Date
29-06-2023

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	E A R T H W O R K
2	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
3	All kinds of soil.
4	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
5	C O N C R E T E W O R K
6	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
7	1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
8	1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
9	1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)
10	Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) at all heights complete as per direction of Engineer-in-charge.
11	Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.
12	REINFORCEDCEMENT CONCRETE
13	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
14	1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
15	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :
16	1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)
17	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
18	Centering and shuttering including strutting, propping etc. and removal of form for :
19	Foundations, footings, bases of columns, etc. for mass concrete
20	Suspended floors, roofs, landings, balconies and access platform including sides of roof slab.
21	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all level.
22	Thermo-Mechanically Treated bars
23	B R I C KW O R K
24	Brick work withcommon burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
25	Cement mortar 1:6 (1 cement : 6 coarse sand)
26	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :
27	Cement mortar 1:6 (1 cement : 6 coarse sand)
28	Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).
29	Cladding Work
30	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size horizontal as well as vertical, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
31	Granite stone slab of colour Z black, Cherry/Ruby red
32	Area of slab upto 0.50 sqm
33	Area of slab over 0.50 sqm
34	Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchenplatform, vanity counter and similar location in marble/ Granite/ stone work, including necessaryholes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
35	Providing and fixing Ist quality ceramic glazed wall tiles of size 300mm x 600mm or more conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
36	W O O D A N DP. V. C.W O R K
37	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.
38	25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws
39	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:
40	35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
41	Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
42	Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :
43	300x16 mm
44	250x16 mm
45	Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :
46	300x10 mm
47	250x10 mm
48	200x10 mm
49	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
50	125 mm
51	100 mm
52	Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
53	Providing and fixing to existing door frames.
54	30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.
55	S T E E L W O R K
56	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
57	Supplying and fixing rolling shutters of approved make, made of requiredsize M.S. laths, interlocked together through their entire length andjointed together at the end by end locks, mounted on specially designedpipe shaft with brackets, side guides and arrangements for inside andoutside locking with push and pull operation complete, including thecost of providing and fixing necessary 27.5 cm long wire springsmanufactured from high tensile steel wire of adequate strengthconforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.
58	80x1.20 mm M.S. laths with 1.20 mm thick top cover
59	Extra for providing mechanical device chain and crank operation for operating rolling shutters.
60	Exceeding 10.00 sqm
61	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses/ Gates etc. etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
62	Hot finished welded type tubes
63	Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
64	In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
65	Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm fixed with self drilling screws complete.
66	Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides
67	Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :
68	4.0 mm thick glass panes
69	F L O O R I N G
70	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
71	25 mm thick
72	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
73	Providing and laying rectified Glazed/Anti skid Ceramic floor tiles of size 400x400 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding pointing the joints with white cement and matching pigments etc., complete.
74	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
75	Double charge vitrified tile polished finish of size
76	Size of Tile 600 x 600 mm
77	Size of Tile 600 x 1200 mm
78	Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm.
79	Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 6mm thickness
80	Providing and laying Vitrified tiles(double charge) in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.
81	Size of Tile 600x600 mm
82	Providing and laying Vitrified tiles (double charged) in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).
83	Size of Tile 600x1200 mm
84	Providing and laying Polished Granite stone flooring/Door sillin required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
85	Polished Granite stone slab colour of Z- Black, Cherry/Ruby Red or equivalent
86	R O O F I N G
87	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
88	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
89	110 mm diameter
90	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
91	Bend 87.5°
92	110 mm bend
93	Shoe (Plain)
94	110 mm Shoe
95	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
96	110 mm
97	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
98	Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
99	Ridges plain (500 - 600mm)
100	Flashings/ Aprons.( Upto 600 mm)
101	F I N I S H I N G
102	12 mm cement plaster of mix :
103	1:6 (1 cement: 6 fine sand)
104	15 mm cement plaster on the rough side of single or half brick wall of mix :
105	1:6 (1 cement: 6 fine sand)
106	Wall paintingwith acrylic emulsion paintof interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.
107	One or more coats
108	Two or more coats on new work
109	Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.
110	New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.
111	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
112	Two or more coats on new work
113	Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
114	Providing and applying white cement based putty of average thickness 0.5 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
115	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :
116	One or more coats on old work
117	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade
118	Old work (one or more coats applied @ 0.83 ltr/10 sqm).
119	Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface
120	REPAIRS TO BUILDING
121	Providing & fixing White vitreous china water closet squatting pan (Indian type) along with \"S\" or \"P\" trap including dismantling of old WC seat and \"S\" or \"P\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.
122	Orissa pattern W.C Pan of size 580x440 mm
123	Hacking of CC flooring/Mosaic flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.
124	DISMANTLING AND DEMOLISHING
125	Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :
126	Of area 3 sq. metres and below
127	Dismantling tile work/Kotastone work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.
128	For thickness of tiles 10 mm to 25 mm
129	Demolishing/Dismantling mud phaska in terracing and disposal of material within 50 metres lead. (Recovery of dismantle tiles will be cradited seprately)
130	Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :
131	15 mm to 40 mm nominal bore metre
132	Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge:
133	Up to 150 mm diameter
134	Dismantling old plaster or skirting/ wall tile raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
135	Road Work
136	Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
137	Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed ofsand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.
138	80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.
139	SANITARY INSTALLATIONS
140	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :
141	W.C. pan with ISI marked white solid plastic seat and lid
142	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :
143	One urinal basin with 5 litre white P.V.C. automatic flushing cistern
144	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :
145	White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap
146	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
147	Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
148	Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.
149	WATER SUPPLY
150	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.
151	20 mm nominal dia Pipes
152	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.
153	20 mm dia nominal bore
154	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :
155	25 to 40 mm nominal bore
156	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
157	25 mm nominal bore
158	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
159	20 mm nominal bore
160	Providing and fixing uplasticised PVC connection pipe with brass unions :
161	45 cm length
162	15 mm nominal bore
163	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
164	150 mm diameter
165	Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :
166	20 mm diameter pipe
167	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work):
168	20 mm nominal bore
169	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
170	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
171	15 mm nominal bore
172	Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.
173	15 mm nominal bore
174	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore
175	15mm nominal bore
176	Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.
177	20 mm nominal bore, 120 mm long, weighing not less than 198 gms
178	D R A I N A G E
179	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :
180	100x100 mm size P type
181	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
182	Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :
183	Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
184	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
185	ALUMINIUM WORK
186	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) :
187	For fixed portion
188	Powder coated aluminium (minimum thickness of powder coating 50 micron)
189	For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
190	Powder coated aluminium (minimum thickness of powder coating 50 micron)
191	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):
192	With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
193	Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.
194	Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side
195	WATER PROOFING
196	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 andapproved by Engineer-in-charge including laying glass fibre cloth of pproved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :
197	With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
198	NEW TECHNOLOGIES AND MATERIALS
199	Providing, mixing and applying bonding coat of approved adhesive including Chipping of unsound/weak concrete material of RCC as perspecifications and direction of Engineer-In-charge complete in all respect.
200	SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer
201	Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used)as per specifications and directions of Engineer-in-charge.Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
202	12 mm average thickness.
203	25 mm average thickness in 2 layers.
204	Miscellaneous items
205	Providing and fixing Stainless steel curtain rods having weight not less then 550 gram per metre including side cap (Big wall type 50 mm dia) fixed with M.S.coated brackets with S.S.screws andPVC sleevesetc., wherever necessary complete :
206	25 mm dia
207	Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with necessary screws complete
208	Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides
209	Providing and applying white cement based putty of average thickness 0.5 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
210	Providing and fixing Table top wash basin [Cera Calburt or equivalent ] of size 550 mm x 400 mm Snow White Table Top Basin with 15 mm C.P. brass pillar taps[ equivalant to cat no 9302 (Prayag make) ,Cera F1015101 Steel Pillar Cock, Silver, Steel Finish or equivalent], 32 mm C.P. brass waste of as per approved make of selection including fittings and waste pipe etc. and fixing on wash basin counter by tile adhesive of approved make.
211	Providing and fixing C.P.brass towel ring complete with brackets fixed to wooden cleats.with C.P. brass screws.of 200 mm diameter of approved brand & as per direction of Engineer-in- charge.
212	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 ,Type B including jointing with adhesive (i) plain socketed pipes.
213	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type B,including jointing with adhesive.
214	Bend 87.5°
215	110 mm bend
216	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type B, including jointing with adhesive.
217	Single tee without door
218	110x110x110 mm
219	Credit for dismantled material received from site of work which will be handed over to contractor as per direction of Engineer-in-charge. Dismantled G.I. Pipe,C.I. pipe, M.S.Etc
220	Credit for dismantled material received from site of work which will be handed over to contractor as per direction of Engineer-in-charge.Dismantled old Wood
221	Credit for dismantled material received from site of work which will be handed over to contractor as per direction of Engineer-in-charge.Dismantled old PVC
222	Cradit for dismantling materials like brick tilesetc
223	Elect
224	SH-I ( Wiring)
225	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
226	Group A
227	Group C
228	Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required.
229	Group A
230	Group C
231	Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
232	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.
233	Group C
234	Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
235	Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
236	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
237	2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
238	2 X 6 sq. mm + 1 X 6 sq. mm earth wire
239	2 X 10 sq. mm + 1 X 6 sq. mm earth wire
240	4 X 6 sq. mm + 2 X 6 sq. mm earth wire
241	4 X 10 sq. mm + 2 X 6 sq. mm earth wire
242	Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.
243	3 X 1.5 Sq.mm
244	6X 1.5 Sq.mm
245	3 x4 Sq.mm
246	6 x4 Sq.mm
247	9 x 4 sq. mm
248	3 x 6 sq. mm
249	6 x 6 sq. mm
250	Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.
251	20 mm
252	25 mm
253	Supplying and fixing of following sizes of flexible steel conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
254	20 mm
255	25 mm
256	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
257	20 mm
258	25 mm
259	Supplying and fixing following sizesDLP U-PVCtrunkingwith cover, andaccessories (Joints, Angles, Bends, End Caps, Brackets, Junctions etc) on surface etc complete as required.
260	80 mm x 50 mm (with separation partition)
261	32 X 12.5 mm
262	Supplying and fixing of following sizes module frame on existing trunking including arranging the cover making good the same as original complete etc. as required.
263	2 Module Frame
264	4 Module Frame
265	6 Module Frame
266	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
267	5/6 amp switch
268	2 way 5/6 A switch
269	15/16 amp switch(Geyser Control)
270	3 pin 5/6 A socket outlet
271	6 pin 15/16 A socket outlet
272	25 amp switch
273	25 A modular socket outlet
274	Supplying and fixing two module stepped type electronic modular fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
275	Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
276	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.
277	1 or 2 Module (75mmX75mm)
278	3 Module (100mmX75mm)
279	4 Module (125mmX75mm
280	6 Module (200mmX75mm)
281	12 Module (200mmX150mm)
282	Supplying and fixing two module stepped type electronic piano fan regulator on the existing phenolic cover plate switch box including connections but excluding cover plate etc. as required.
283	Supplying and fixing one module stepped type electronic piano fan regulator on the existing phenolic cover plate switch box including connections but excluding cover plate etc. as required.
284	Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.
285	5/6 A switch
286	2 way 5/6 A switch
287	15/16 A switch
288	3 pin 5/6 A socket outlet
289	6 pin 15/16 A socket outlet
290	Supplying and fixing suitable size GI box with modular plate andcover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
291	Supply & Fixing suitable size GI Box with modular plate and cover in front on surface or in reccess including provising and fixing 6 pin 5/6 and 15/16 amps moduler socket outlet and 15/16 amps moduler switch connection ect. as required.
292	Supplying and fixing suitable size GI/ PVC box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 6 pin 15/16 A modular socket outlet and 2 nos. 15/16 A modular switch, connections etc. as required.
293	Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
294	Installation, testing, commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/ CFL / LEDlamps per fitting/ /Downlighters/ LED Panel Light /LED batten on wall or ceiling, complete with all accessories including connection and earthing etc. as required.
295	Supplying and fixing extra down rod of 10 cm length G.I. pipe ,15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)
296	Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)
297	Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
298	Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
299	1 run of cable
300	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).
301	Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \"C\" curve including connections, painting etc. as required.( For Geyser)
302	Supplying and fixing PVC batten/ angle holder including connections etc. as required.
303	Providing and fixing a metallic louvred shutter suitable for following sizes exhaust fan, the louvres should be able to open when the fan is on and close when the fan is turned off, on the existing opening on the wall, etc., as required.
304	i) 300 mm
305	Providing and fixing 3 mm thick PVC/phenolic laminatedround sheet cover with a minimum of 170 mm dia on the existing fan box with two screws, etc., as required.
306	Providing and fixing 3 mm thick PVC / phenolic laminatedround sheet cover on the existing junction boxwith two screws, etc., as required.
307	Supplying and fixing 3 mm thick phenolic laminated sheet cover on existing switch Box / metal box with Al. Alloy/ cadmium/ zinc plated screws and washers, including cutting the laminated sheet to required shape and size etc., complete as required.
308	Supplying and fixing suitable size GI box in recess, including providing and fixing of 3/4 Module LED Foot light /skirting light,including connection etc. as required.
309	Supplying and fixing two module Buzzer on the existing modular plate switch box including connections but excluding modular plate etc. as required.
310	Supplying and fixing two module bell/ chime on the existing modular plate switch box including connections but excluding modular plate etc. as required.
311	Supplying and fixingPRCD (Portable Residual Current Device) Plug top, 16 A 30 mA rating including connection etc. as required.
312	Supplying and fixing Plug top following rating including connection etc. as required.
313	16 A, three pin, Plug top ISI marked
314	6 A, three pin, Plug top ISI marked
315	25 A, three pin, Plug top ISI marked
316	Supplying, installation, testing and commissioning of Astronomical time switch of following configuration to be mounted in feeder pillars / Lighting DBs for automatic switching On & OFF of street lights at sun set & sun rise or twilight (Auto ON, Auto OFF, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site complete as required.
317	1 output per phase and suitable for single phase supply
318	Supplying, installation, testing and commissioning of single phase25 A Modular Power Contactorwith manual override facility and manual ON/OFF to be mounted in Lighting DBs including connection etc. as required.
319	Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab, including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete.
320	Supplying and fixing of following size PVC Saddles with base and screws on existing PVC / steel conduit etc as reqd (Precision / AKG /Polycab /Finolex / Anchor/ GM)
321	20 mm
322	25 mm
323	Supplying and installation of PVC Exhaust fanwith louver shutter 200 mm sweep in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.(Havells / C&G / Orient / Usha / Almonard/ Atomberg)
324	Supplying and installation of PVC Exhaust fanwith louver shutter 250 mm sweepin the existing opening, including making good the damage, connection, testing, commissioning etc. as required.(Havells / C&G / Orient / Usha / Almonard/ Atomberg)
325	250 mm sweep
326	Supplying and installation of 300 mm sweep, 1400 RPM heavy-duty, single phase, metallic exhaust fan Conforming to IS:2312 -1967in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.(HavellsTurbo force Heavy Duty Exhaust Fan or with similar specifications C&G / Orient / Usha / Almonard)
327	300 mm sweep
328	Supplying and installation of 225/ 230 mm sweep, single phase, metallic exhaust fanin the existing opening,including making the hole to suit the size of the above fan and making good the damage, connection, testing, commissioning etc. as required.(HavellsVentil Airor with similar specifications C&G / Orient / Usha / Almonard)
329	Making holes of the required size and shape in a brick masonry wall for installation of the following size exhaust fan, including making good the wall by plastering and finishing with the matching surface, etc., complete as per the direction of the engineer-in-charge.
330	200 mm sweep.
331	225/230 mm sweep.
332	250 mm sweep.
333	Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.
334	Supply and fixing of 8 mm thick BWP/marine grade plywood wood board having a circular /rectangular hole to suit the sie of exhaust fan upto 380 mm on wall /window for etc as required including the cost of making hole, nuts and bolts,etc. as required.
335	Supply and installation of 400 mm sweep, 220 V, wall mounted fan along withspeed regulator unit for speed control, on the existing wall,including connection, testing, commissioning etc. as required. (Make: Atomberg/Crompton/Havells/Orient/Usha/Bajaj/Almonard)
336	400 mm sweep
337	Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, down rod upto 30 cm long , 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 8, Air delivery minimum 215 Cum/Min, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%,without remote and compatible with existing step electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise 75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. (BLDC Ceiling fan with minimum 2 year Warranty ofAtomberg/ Usha/ Orient / Havells /Cromptonmake)
338	Supply, Installation, Testing and Commissioning of following size/sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, down rod upto 30 cm long , 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 8, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%,without remote and compatible with existing step electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise 75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. (BLDC Ceiling fan with minimum 2 year Warranty ofAtomberg/ Usha/ Orient / Havells /Cromptonmake)
339	900 mm sweep BLDC ceiling fan.
340	Supply, installation, testing, and commissioning of 2 ft. x 2 ft. (nominal size) LED Surface Mounted LED Panel Light, in metallic housing, with a minimum system lumen output of 3960 lumens and a minimum system luminous efficacy of 110 lm/W, colour temperature of 5500K–6500K, average life L70B50: 50000 hours, THD = 10%, suitable for operation on 140-270V, 1F, 50Hz AC supply system, complete with all accessories, electronic driver, diffuser, directly on the ceiling, including connections, earthing, etc. as required.
341	Supply, installation, testing, and commissioning of 2 ft. x 2 ft. (nominal size) LED recessed Mounted LED Panel Light, in metallic housing, with a minimum system lumen output of 3960 lumens and a minimum system luminous efficacy of 110 lm/W, colour temperature of 5500K–6500K, average life L70B50: 50000 hours, THD = 10%, suitable for operation on 140-270V, 1F, 50Hz AC supply system, suitable for recessed mounting, Armstrong/grid/POP/GB ceiling complete with all accessories, diffuser and electronic driver, directly on the ceiling, including connections and earthing etc. as required.
342	Supply, installation, testing, and commissioning of integrated LED Batten luminaire, 1200 mm (nominal size) with a minimum system lumen output of 2400 lumen and with a minimum system luminous efficacy of 120 lm/W, made of aluminium housing having a colour temperature5500K - 6500 K, Average life L70B50: 50000 hours, THD = 10%, suitable for operation on 140-270V, 1F, 50Hz AC supply system, complete with all accessories, electronic driver, diffuser, directly on the ceiling/wall, including connections, earthing, etc. as required.
343	Supply, installation, testing, and commissioning of integrated LED Batten luminaire, 1200 mm (nominal size) with a minimum system lumen output of 4800 lumen and with a minimum system luminous efficacy of 120 lm/W, made of aluminium housing having a colour temperature5500K - 6500 K, Average life L70B50: 50000 hours, THD = 15%, suitable for operation on 140-270V, 1F, 50Hz AC supply system, complete with all accessories, electronic driver, diffuser, directly on the ceiling/wall, including connections, earthing, etc. as required.
344	Supply, installation, testing and commissioning of Bulk Head LED fittings with minimum 1000 lumens, efficacy not less than 100 lm / watt, having High grade polycarbonate / CRCA housing,housing with diffused optic, CCT 5700- 6500 K, CRI >70, PF > 0.9, THD< 10%, 50,000burning hours lifetime @L70 & SPD Device of appropriate Kv to support its minimum 5 Year life warranty
345	Supply, installation, testing, and commissioning of integrated LED Batten luminaire, 600 mm (nominal size) with a minimum system lumen output of 1000 lumen andwith a minimum system luminous efficacy of 100 lm/W, made of aluminium housing having a colour temperature5500K - 6500 K, Average life L70B50: 50000 hours, suitable for operation on 140-270V, 1F, 50Hz AC supply system, complete with all accessories, electronic driver, diffuser, directly on the ceiling/wall, including connections, earthing, etc. as required.
346	Supply, installation, testing and commissioning of surface mountedLED downlighter luminaire inmetallic housing, with a minimum system lumen output of 1500 lumen andwith a minimum system luminous efficacy of 100 lm/W, Average LED life L70B50: 50000 hours, suitable for operation on 140-270V, 1F, 50Hz AC supply system, complete with all accessories, diffuser and electronic driver, directly on ceiling, including connections and earthing etc. as required.
347	Supply, installation, testing and commissioning of surface mountedLED downlighter luminaire inmetallic housing, with a minimum system lumen output of 1800 lumen andwith a minimum system luminous efficacy of 100 lm/W, Average LED life L70B50: 50000 hours, suitable for operation on 140-270V, 1F, 50Hz AC supply system, complete with all accessories, diffuser and electronic driver, directly on ceiling, including connections and earthing etc. as required.
348	Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.
349	100A, 16 KA/18KA, TP MCCB
350	Supplying of3 liters capacity vertical mounting type water storage heater with safety system for protection against over heatingand external adjustable thermostat suitable for working with 230V AC, 50 Hz, 1 Phase supply with 16A 3 Pin Plug Top including pair of 450 mm length flexiable connection pipes and 02 nos 8mm X 75mm size steel fastner etc as required as per direction of engg-in-charge.
351	Supplying, installation testing and commissioning of BEE5 star rating, 6 litres capacity water storage heater, withprotection against over heating, Multifunction Safety Valveandexternal adjustable thermostat, with16 A, 240 V, plug top with in-built 30 mA RCDand02 nosflexible connection pipe suitable for working with 230V AC, 50 Hz, 1 Phase supply etc as required. (Make:Havells / Crompton/ AO Smith /Racold /Jaguar with 7 year warranty on inner tank, 3 year warranty on heating element, 2 year comprehensive Warranty)
352	Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
353	Single pole
354	Double pole
355	Triple pole and neutral
356	Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
357	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)(Note : DB should be suitable for RCCB/RCBO as incomer.)
358	4 way (8 + 18), Double door
359	Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB\"s (but without MCB\"s and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)
360	4 way (8 + 12), Double door
361	Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required.
362	For 4 way, Double door TPN MCBDB
363	Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
364	6 way, Double door
365	8 way, Double door
366	12 way, Double door
367	16 way, Double door
368	Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required.
369	For 6 way, Double door SPN MCBDB
370	For 8 way, Double door SPN MCBDB
371	For 10 way/12 WAY, Double door SPN MCBDB
372	For 14 way/16 way, Double door SPN MCBDB
373	Providing and fixing following capacity & size, 4-pole 415 V, powder painted metallic bus-bar box , on surface/recess, cable knock-outs for entry/exit, 4-strips ofcolour coded copper strips in step type arrangement complete with bakelite insulator sheet, powder painted including earthing etc. as required. ( Make:Socomec / Tekson / HPL /Sainik/ Havells)
374	63 A Bus-bar box of nominal size 28 x 23 x 13 cm
375	100 A Bus-bar box of nominal size 36 x 30x 15 cm
376	Supplying and fixing TP sheet steel enclosure on surface/ recessalong with 16/25/32 A 415 V \"C\" curve TP MCB complete withconnections, testing and commissioning etc. as required.
377	Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
378	Supplying and fixing feed through terminal 100 A in the existing looping box/junction box, including connection, etc., as required. (Connect well/Elmex/ Phoenix/ Wago/ Essen)
379	Supplying and fixing feed through terminal 75 A in the existing looping box/junction box, including connection, etc., as required. (Connect well/Elmex/ Phoenix/ Wago/ Essen)
380	Supplying and fixingshorting link suitable for 75 A feed through terminals in existing looping box/junction box, etc. as required. (Connect well/Elmex/ Phoenix/ Wago/ Essen)
381	Supplying and fixingshorting link suitable for 100 A feed through terminals in existing looping box/junction box, etc. as required. (Connect well/Elmex/ Phoenix/ Wago/ Essen)
382	Supplying and fixing end plates for 75A feed through terminals in existing looping boxes/ junction boxes, etc. as required. (Connect well/Elmex/ Phoenix/ Wago/ Essen)
383	Supplying and fixing end plates for 100A feed through terminals in existing looping boxes/ junction boxes, etc. as required. (Connect well/Elmex/ Phoenix/ Wago/ Essen)
384	Supplying and fixing a PVC cable gland suitable for up to 6 sq mm of copper conductor cable in the existing polycarbonate cable junction box, including connections, etc. as required.(Hensel/ Dowells/ Barco/ Connectwell/ Elmex /Eaton/ Legrand)
385	Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
386	40 A
387	Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
388	40 A
389	63 A
390	Supplying and fixing following rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required
391	40 A Double pole
392	63 A Double pole
393	Supplying and fixing following rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
394	40 ATriple pole and neutral
395	63 ATriple pole and neutral
396	Fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
397	6 to 16 way,Double door
398	Supplying and fixing polycarbonate weatherproof, IP66 outdoor type cable junction box on the surface or recess, complete with a two-way, five-pole terminal block, including connections, etc., complete as required.(Hensel KF 0404 G /Legrand / CAPE/ ELM / GEWISS/ SPELSBERG / RITTAL/ EATON/OBO)
399	Supplying and fixing polycarbonate weatherproof, IP66 outdoor type cable junction box on the surface or recess, complete with a two-way, five-pole terminal block, including connections, etc., complete as required.(Hensel KF 1010 G /Legrand / CAPE/ ELM / GEWISS/ SPELSBERG / RITTAL/ EATON/OBO)
400	Supplying and fixing polycarbonate weatherproof, IP66 outdoor type cable junction box with minimum dimensions of 155 mm x 210 mm x 92 mm on surface or recess, including connections etc., complete as required. ( Hensel KF 1600G/Legrand / CAPE/ ELM / GEWISS/ SPELSBERG / RITTAL/ EATON/OBO)
401	Supplying and fixing polycarbonate weatherproof, IP66 outdoor type cable junction box with minimum dimensions of 205 mm x 255 mm x 112 mm on surface or recess,including connections etc., complete as required. (Hensel KF 2500G / Legrand / CAPE/ ELM / GEWISS/ SPELSBERG / RITTAL/ EATON/OBO)
402	SH-IV (Service Connection)
403	Supplying and laying of one number armoured PVC/XLPE insulated and PVC sheathed/XLPE aluminium conductor power cable 1.1 KV grade of following size in the existing RCC/ HUME/ STONEWARE/ METAL/ DWC pipe as required.
404	3½X 35 Sq.mm
405	Supplying and laying of one number armoured PVC/XLPE insulated and PVC sheathed/XLPE aluminium conductor power cable 1.1 KV grade of following size in Masonry Open Duct Loose/loop/in panel etc. complete etc as required.
406	3½X 35 Sq.mm
407	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
408	3½ X 35 sq. mm (32mm)
409	Providing and fixing G.I. pipes complete with G.I. fittings including trenching(75 cm deep) and refilling etc.
410	50 mm dianominal bore
411	Supplying and laying of G.I. pipe of 50 mm dia.(nominal),medium class, ISI markedinwall / floorincluding cuttingchase, and making good the wall/ floor and finishing with matching surface after housing G.I. pipe in chase. ( for protection of UG cable)
412	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.
413	63 mm dia ( OD-63 mm & ID-51 mm Nominal)
414	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.
415	63 mm dia ( OD-63 mm & ID-51 mm Nominal)
416	Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.
417	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.
418	Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
419	Cutting road and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required.
420	Bituminous portion
421	Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
422	Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling etc as required.
423	Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
424	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclo sure with cover plate having locking arrangement and wa tering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
425	Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
426	Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
427	Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.
428	Excavation for cable trenches in soft soil, depth upto 1.2 m including dressing of sides lift upto 1.5 m, including getting out the excavated soil, refilling with sand and or good soil after laying of cable/ pipe etc in layers of 20 cm, ramming, watering and disposal of surplus excavated soil as directed, within a lead of 50 metres.
429	Rewinding of following size ceiling fan / exhaust fan/ Wall fanmotor including complete removal of existing burnt out winding and rewinding of the fan with suitable size enameled copper wire, including sleeving, suitable insulation materials, varnishing etc., complete with dismantling and reassembling after repair, including connection testing etc. as required. Removed winding wire shall be retained by the contractor and suitably credited with its value and net value to be quoted.
430	1200mm Sweep ceiling fan
431	Providing and replacing ball bearing in following sizeceiling fan/exhaust fan, including removing old ball-bearing, installing new ball bearing and testing the fan, etc., as required.(Scrap material will be retained by the contractor).(Both side shield ball bearing of SKF/ NBC /TATA )
432	1200mm Sweep ceiling fan.
433	Providing and replacing the 2.5 MFD/3.15 MFD fan capacitor in the ceiling fan/exhaust fan/wall fan, including connection and testing, etc., as required. (The old capacitor will be retained by the contractor).
434	Reconditioning of the oversized bush bearing housing to a suitable ball bearing in the ceiling fan/ exhaust fan/ wall-mounted fans as required and assembling and testing of the fan after repair. All the scrap material should be retained by the contractor.
435	Providing and replacing the worn-out M.S. shaft of the exhaust fan /wall fan with a suitable size new shaft etc., as required, including removing the old shaft, installing the new shaft, and testing the fan.All the scrap material should be retained by the contractor.
436	SH- II (DISMANTLING)
437	Dismantling of the existing switch accessories like switches, sockets, and MCBs, etc., as required.
438	Dismantling of the existing ceiling rose, holder, and wall bracket and depositing the same with the listing of materials in the store.
439	Dismantling of existing fluorescent fitting from ceiling/ wall including making good the damage to match the adjacent surface, etc., as required.
440	Dismantling of the existing ceiling fan/ exhaust fan of any size installed in the building and depositing it in the MMC store.
441	Dismantling of the existing recessed vertical type or horizontal type TPN MCB distribution board of any size along with MCBs and other accessories, including making good the damage to match the adjacent surface, etc., as required.
442	Dismantling of the existing recessed SPN MCB distribution board of any size along with MCBs and other accessories, including making good the damage to match the adjacent surface, etc., as required.
443	Dismantling of the existing recessed switch board of light points/power points, power/light plug points/socket outlet metal boxes of any size, along with phenolic laminated sheet, switches, sockets, etc., making good the damage to match the adjacent surface, etc., as required.
444	Dismantling wires from the following sizes, existing circuit/submain/power wiring conduits, complete as required. The length of the conduit from which the wires are removed will be measured for payment purposes, irrespective of the number of wires in it.Above 25 mm conduits.
445	Dismantling wires from the following sizes, existing circuit/submain/power wiring conduits, complete as required. The length of the conduit from which the wires are removed will be measured for payment purposes, irrespective of the number of wires in it.Up to 25 mm conduit.
446	Dismanttling of cable from already excavated ground, pipe, and disconnection from existing panel, box etc complete with shifting of material to respective MMC. Upto 35 sq.mm
447	Dismanttling of cable from already excavated ground, pipe, and disconnection from existing panel, box etc complete with shifting of material to respective MMC.Above 35 sq. mm and upto 95 sq. mm
448	Dismanttling of cable from already excavated ground, pipe, and disconnection from existing panel, box etc complete with shifting of material to respective MMC.Above 95 sq. mm and upto 185 sq. mm
449	Dismanttling of cable from already excavated ground, pipe, and disconnection from existing panel, box etc complete with shifting of material to respective MMC.Above 185 sq. mm and upto 400 sq. mm
450	The road crossings of power cablethrough trenchless boring. Trenchless horizontal boring using Manual/ Machine Moling techniqueat 0.75 metre below the ground level for following size pipes,including survey of under ground utilities,excavation of pits,moling with the hole size not exceeding 20% of the pipe dia,backfilling, compaction and restoration of the pits to original condition etc. as required. The rates for moling, as indicated are inclusive of excavation of pits, backfilling, compaction andrestoration of the pits to original condition. Any damages occurred to other utilities during the Moling operation shall be immediately notified and rectified by the contractor without any cost implication to the Department. The length of the Hole (excluding the sizes of the pits on both ends) shall be considered for the measurement of Moling length. However, intermediate pits will consider in the moling length.i)Upto 200 mm dia DWC HDPE / G.I. /PVC
451	Providing and erection of G.I. pipe medium class of the following diameter in the existing gate pillar for fixing the post-top lantern, including making holes and embedding the required length of the pipe in the pillar top, and making good the damage with matching concrete, plastering, and painting after the erection of the pipe, etc., complete as per the direction of the engineer-in-charge.
452	G.I. pipe 50 mm dia
453	Supply and drawing of 3 x 2.5 sq mm PVC insulated, FRLSPVCsheathed copper conductor multi core flexible cable into the existing street light pole/ PVC / DWC/ steel conduit, making connectionsetc. as required.
454	Supplying, installation, testing and commissioning of 45 Watt LED street light luminaire made up of die-cast aluminium housing, with IP66 degree of protection, complete with the driver, LEDs with optical lens, toughened glass cover, etc. The luminaire driver should have an operating voltage range of 140-270 Volt, a mechanical impact resistance rating of lk>=07. surge protection of = 10KV, PF= 0.90 and minimum system luminous efficacy of 100 lm/W. The luminaire shall be designed for a system life of 50,000 hours and suitable for mounting on pole bracket up to outer dia 50 mm, including installation on existing street light pole bracket connections and earthing etc., as required. LM 79 and LM 80 reports need to be submitted from a NABL/UL accredited lab to verify the above parameters.
455	Supplying and fixing of 32 mm dia X 2.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV/LED street light fitting on pole/ wall including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.
456	Providing and fixing Stainless Steel S Shaped Hooks of 8 mm dia. rod in existing R.C.C. slab, including cutting chase, anchoring clamp to a reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete.
457	SH- III (CREDIT)
458	Less credit for the unserviciable items dismantled items during execution of the work.
459	Assorted MCB TP AND TP&N & OTHER SWITCHGEAR
460	Assorted PIANO Type Switches
461	Assorted PIANO Type Sockets
462	Assorted Bell push/PIANO Type
463	Assorted Call bell buzzer single phase
464	Assorted Brass batten/ angle holder/Brass Bracket
465	Assorted Fan regulator/resistance type
466	Assorted Telephone Socket outlet
467	Assorted T.V. Socket outlet
468	Assorted Capacitor, 3.15/2.50/2.25 mfd
469	Assorted 1200/1400 mm sweep ceiling Fanwith blades
470	Assorted Fresh Air FAN 200/250
471	Assorted Exhaust fan 300/380/450
472	Assorted Wall Bracket Fittings
473	Assorted fluorescent Light Fittings
474	Assorted Bulk Head Fittings
475	less credit for the dismantled Copper wirewires from light points/ circuit/ submain/power circuit wiring,.
476	less credit for the dismantled aluminium wirewires from light points/ circuit/ submain/power circuit wiring,.
477	Assorted metal switch box.
478	Assorted MCB DB SPN with out MCBs
479	Assorted MCB DB TPN without MCBs
480	Assorted MCB SP
481	Assorted MCB DP
482	Assorted MCB TP AND TP&N
483	Add 1.0633 multiplying factor for GST on DSR items

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Haryana Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Arm Of Logistic Group Buildings At Nsg Campus Manesar For The Year 2023 24 Sh Civil And Elect Maintenance, Manesar-Haryana

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Arm Of Logistic Group Buildings At Nsg Campus Manesar For The Year 2023 24 Sh Civil And Elect Maintenance, Manesar-Haryana

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us